Datasheet
Visible red or infrared backlights in 2 sizes, with 3-conductor cable
• Diffused backlight for PresencePLUS® Pro sensors. See Banner’s website
at www.bannerengineering.com for a complete lighting tutorial.
• Continuous light and strobed operation, selectable via sensor software
• Solid-state LED matrix, in two sizes.
• Direct connection to PresencePLUS Pro or to an external power supply
using 3 discrete wires.
• Two sizes available; see models table.
• Bracket option(s) available for all models.
Models
Model LED Color Wave Length Active Area
LEDIB70X70W Infrared 940 nm 71 x 71 mm
(2.8" x 2.8")
LEDRB70X70W Visible Red 660 nm
LEDIB85X220W Infrared 940 nm 85 x 220 mm
(3.35" x 8.67")
LEDRB85X220W Visible Red 660 nm
To order the 9 m (30 ft) integral cable model, add the suffix “W/30” to the model number (for example, LEDIB70X70W
W/30).
Specifications
Light Source
LED; see models table for wavelengths
Illumination
Diffused for use in applications needing a backlit light source.
Supply Voltage and Current
70 X 70 mm models: 24 V dc at 250 mA max.
85 x 220 mm models: 24 V dc at 500 mA max.
Connections
2 m (6.5 ft) or 9 m (30 ft) PUR-jacketed, 3-conductor attached cable
Construction
Low-carbon steel with black zinc plating, acrylic window
Useful Life
10,000 hours (LED ON time). When operated within specifications,
output will decrease less than 30% after 10,000 hours and less than
40% after 20,000 hours.
Operating Conditions
0 °C to 50 °C (32 °F to 122 °F)
90% at 50 °C (non-condensing) max. relative humidity
Cleaning Instructions
• Regularly remove any dust, dirt, or fingerprints from the light
source.
• Blow off dust using anti-static compressed air.
• If necessary, use a lens cloth and lens cleaner or window
cleaner to wipe off remaining debris. Do not use any other
chemicals for cleaning.
LED..B..W Series Backlights
Original Document
115349 Rev. C 27 February 2014
115349
Wiring Table
Backlight Wire PresencePLUS Pro
Controller Terminal Block External Power Supply
(Strobed) External Power Supply
(Continuous)
Brown Pin 1 (+V 1) +V +V
Blue Pin 2 (–V 2) –V –V
Black Pin 4 (strobe) +5 V dc
–V OFF
ON –V
Dimensions
110.4 mm
(4.35")
92.6 mm
(3.65")
46.2 mm
(1.81")
13.8 mm
(0.54")
94.0 mm
(3.70")
61.0 mm
(2.40")
15.8 mm
(0.62")
8.2 mm
(0.32")
10.8 mm
(0.43")
19.7 mm
(0.78")
71.0 mm
(2.80")
71.0 mm
(2.80")
4x M4 x 0.7
(7.1 mm Deep)
25.4 mm
(1.0")
Figure 1. Backlight, 70x70 mm model
6.9 mm
(0.27")
275.8 mm
(10.86") 244.3 mm
(9.62")
108.2 mm
(4.26")
25 mm
(0.98")
27.9 mm
(1.10")
220.0 mm
(8.66")
11.6 mm
(0.45")
85.0 mm
(3.3")
17.4 mm
(0.69")
73.5 mm
(2.89")
Figure 2. Backlight, 85x220 mm model
1+V = 24V dc ± 10%
2–V = dc common
LED..B..W Series Backlights
2 www.bannerengineering.com - tel: 763-544-3164 P/N 115349 Rev. C
Accessory Mounting Brackets
SMBABM
• 13-ga. zinc-plated low-
carbon steel
• (4) M4 Phillips flathead
screws included
• For mounting light from
front
• Accommodates backlight
models LED..B70X70..
86.4 mm
(3.40")
60.9 mm
(2.40")
40.6 mm
(1.60")
2.3 mm
(0.09")
2x 12.7 mm
(0.50")
10.2 mm
(0.40")
30.5 mm
(1.20")
8.8 mm
(0.35")
5.1 mm
(0.20")
4.7 mm
(0.18")
2x Ø4.6 mm
(0.18")
C'sink ø8.3 mm
(0.33")
SMBACM
• 14-ga. zinc-plated low-
carbon steel
• (4) M4 socket-head cap
screws, washers and hex
key included
• For mounting light from
rear
• Accommodates backlight
models LED..B70X70..
110.2 mm
(4.34")
10.2 mm
(0.40")
2x 22.9 mm
(0.90")
55.1 mm
(2.17")
94.0 mm
(3.70")
15.8 mm
(0.62")
61.0 mm
(2.40")
92.5 mm
(3.64")
8.1 mm
(0.32")
46.2 mm
(1.82")
2x 14.9 mm
(0.59")
2x M6 x 1
1/4-20
SMBLB
• Accommodates backlight
models LED..B85X220..
76.2 mm
(3.0")
40.6 mm
(1.6")
73.5 mm
(2.89")
12.7 mm
(0.50")
11.5 mm
(0.45")
10.2 mm
(0.40")
8.9 mm
(0.35")
2.3 mm
(0.09")
99.1 mm
(3.9")
2 x Ø 6.6 mm
(0.26")
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following
the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture
which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty
does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR
IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR
TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO
EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR
ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR
SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE
PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY,
NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any
obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp.
LED..B..W Series Backlights
www.bannerengineering.com - tel: 763-544-3164
