A Business Partner of Renesas Electronics Corporation. Data Sheet NE3520S03 R09DS0029EJ0100 Rev.1.00 Oct 18, 2011 N-Channel GaAs HJ-FET, K Band Low Noise and High-Gain FEATURES * Low noise figure and high associated gain: NF = 0.65 dB TYP., Ga = 13.5 dB TYP. @ f = 20 GHz, VDS = 2 V, ID = 10 mA * K band Micro-X plastic (S03) package APPLICATIONS * 20 GHz band DBS LNB * Other K band communication system ORDERING INFORMATION Part Number NE3520S03-T1C Order Number NE3520S03-T1C-A NE3520S03-T1D NE3520S03-T1D-A Package S03 package (Pb-Free) Quantity 2 kpcs/reel Marking J Supplying Form * Embossed tape 8 mm wide * Pin 4 (Gate) face the perforation side of the tape 10 kpcs/reel Remark To order evaluation samples, please contact your nearby sales office. Part number for sample order: NE3520S03-A ABSOLUTE MAXIMUM RATINGS (TA = +25C, unless otherwise specified) Parameter Symbol Ratings Unit Drain to Source Voltage VDS 4.0 V Gate to Source Voltage VGS -3.0 V ID IDSS mA IG 100 A Ptot 165 mW Tch +125 C Drain Current Gate Current Total Power Dissipation Note Channel Temperature Storage Temperature Tstg -65 to +125 Note: Mounted on 1.08 cm2 x 1.0 mm (t) glass epoxy PWB C CAUTION Observe precautions when handling because these devices are sensitive to electrostatic discharge. R09DS0029EJ0100 Rev.1.00 Oct 18, 2011 Page 1 of 8 NE3520S03 RECOMMENDED OPERATING RANGE (TA = +25C, unless otherwise specified) Parameter Symbol MIN. TYP. MAX. Unit VDS +1 +2 +3 V Drain Current ID 5 10 15 mA Input Power Pin - - 0 dBm Drain to Source Voltage ELECTRICAL CHARACTERISTICS (TA = +25C, unless otherwise specified) MIN. TYP. MAX. Unit Gate to Source Leak Current Parameter IGSO VGS = -3.0 V - 0.5 10 A Saturated Drain Current IDSS VDS = 2 V, VGS = 0 V 25 40 70 mA Gate to Source Cut-off Voltage Symbol Test Conditions VGS (off) VDS = 2 V, ID = 100 A -0.2 -0.7 -1.3 V Transconductance gm VDS = 2 V, ID = 10 mA 50 65 - mS Noise Figure NF VDS = 2 V, ID = 10 mA, f = 20 GHz - 0.65 0.90 dB Associated Gain Ga 11.5 13.5 - dB R09DS0029EJ0100 Rev.1.00 Oct 18, 2011 Page 2 of 8 NE3520S03 TYPICAL CHARACTERISTICS (TA = +25C, unless otherwise specified) TOTAL POWER DISSIPATION vs. AMBIENT TEMPERATURE Total Power Dissipation Ptot (mW) 250 Mounted on Glass Epoxy PCB (1.08 cm2 x 1.0 mm (t) ) 200 150 100 50 0 50 100 150 200 250 Ambient Temperature TA (C) DRAIN CURRENT vs. DRAIN TO SOURCE VOLTAGE DRAIN CURRENT vs. GATE TO SOURCE VOLTAGE 80 80 70 70 60 60 VGS = 0 V 40 -0.1 V 30 -0.2 V 20 -0.3 V 10 -0.4 V -0.5 V 1.0 2.0 40 30 20 10 3.0 0 -0.8 4.0 -0.6 -0.4 -0.2 0 Drain to Source Voltage VDS (V) Gate to Source Voltage VGS (V) MINIMUM NOISE FIGURE, ASSOCIATED GAIN vs. FREQUENCY MINIMUM NOISE FIGURE, ASSOCIATED GAIN vs. DRAIN CURRENT 20 1.1 VDS = 2 V ID = 10 mA 19 1.0 18 0.9 17 0.8 16 0.7 15 0.6 14 Ga 13 0.5 12 0.4 0.3 0.2 10 NFmin 11 15 20 25 16 1.5 10 Frequency f (GHz) Minimum Noise Figure NFmin (dB) 1.2 Minimum Noise Figure NFmin (dB) 50 1.4 f = 20 GHz VDS = 2 V 15 1.3 14 Ga 1.2 13 1.1 12 1.0 11 0.9 0.8 10 NFmin 9 0.7 8 0.6 7 0.5 0 5 10 15 20 Associated Gain Ga (dB) 0 0.0 Drain Current ID (mA) 50 Associated Gain Ga (dB) Drain Current ID (mA) VDS = 2 V 6 25 Drain Current ID (mA) Remark The graphs indicate nominal characteristics. R09DS0029EJ0100 Rev.1.00 Oct 18, 2011 Page 3 of 8 NE3520S03 S-PARAMETERS S-parameters/Noise-parameters are provided on our web site in a form (S2P) that enables direct import to a microwave circuit simulator without keyboard input. Click here to download S-parameters. [RF and Microwave] [Device Parameters] URL http://www2.renesas.com/microwave/ R09DS0029EJ0100 Rev.1.00 Oct 18, 2011 Page 4 of 8 NE3520S03 RF MEASURING LAYOUT PATTERN (REFERENCE ONLY) (UNIT: mm) 2.80 2.60 2.06 0.64 Reference Plane (Calibration Plane) 13.0 0.54 0.74 1.60 2.2 S-S2.2mm 1.7 1.7 Reference Plane (Calibration Plane) 0.3 TH 6.0 RT/duroid 5880/ROGERS t = 0.254 mm r = 2.20 tan delta = 0.0009 @10 GHz Au-flash plate R09DS0029EJ0100 Rev.1.00 Oct 18, 2011 Page 5 of 8 NE3520S03 PACKAGE DIMENSIONS S03 (UNIT: mm) (Top View) (Bottom View) 3.20.2 0.65 TYP. 2.20.2 1 2.20.2 0.5 TYP. 2.60.1 1 J 2 4 4 2 3 3 (Side View) 2.20.2 0.150.05 1.5 MAX. 1.7 3.20.2 PIN CONNECTIONS 1. 2. 3. 4. R09DS0029EJ0100 Rev.1.00 Oct 18, 2011 Source Drain Source Gate Page 6 of 8 NE3520S03 RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Infrared Reflow Partial Heating Soldering Conditions Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220C or higher Preheating time at 120 to 180C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) : 260C or below : 10 seconds or less : 60 seconds or less : 12030 seconds : 3 times : 0.2% (Wt.) or below Peak temperature (terminal temperature) : 350C or below Soldering time (per side of device) : 3 seconds or less Maximum chlorine content of rosin flux (% mass) : 0.2% (Wt.) or below Condition Symbol IR260 HS350 CAUTION Do not use different soldering methods together (except for partial heating). R09DS0029EJ0100 Rev.1.00 Oct 18, 2011 Page 7 of 8 NE3520S03 Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. * Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. * Do not burn, destroy, cut, crush, or chemically dissolve the product. * Do not lick the product or in any way allow it to enter the mouth. R09DS0029EJ0100 Rev.1.00 Oct 18, 2011 Page 8 of 8 Revision History Rev. 1.00 Date Oct 18, 2011 NE3520S03 Data Sheet Description Summary Page - First edition issued All trademarks and registered trademarks are the property of their respective owners. C-1 Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website. 2. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. 3. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. 4. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 5. When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. 6. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics 7. Renesas Electronics products are classified according to the following three quality grades: "Standard", "High Quality", and "Specific". The recommended applications for each Renesas Electronics product assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. depends on the product's quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application categorized as "Specific" without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as "Specific" or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is "Standard" unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc. "Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; safety equipment; and medical equipment not specifically designed for life support. "Specific": Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life. 8. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. 9. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 10. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 11. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics. 12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries. (Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics. http://www.renesas.com SALES OFFICES Refer to "http://www.renesas.com/" for the latest and detailed information. Renesas Electronics America Inc. 2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A. Tel: +1-408-588-6000, Fax: +1-408-588-6130 Renesas Electronics Canada Limited 1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada Tel: +1-905-898-5441, Fax: +1-905-898-3220 Renesas Electronics Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K Tel: +44-1628-585-100, Fax: +44-1628-585-900 Renesas Electronics Europe GmbH Arcadiastrasse 10, 40472 Dusseldorf, Germany Tel: +49-211-65030, Fax: +49-211-6503-1327 Renesas Electronics (China) Co., Ltd. 7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China Tel: +86-10-8235-1155, Fax: +86-10-8235-7679 Renesas Electronics (Shanghai) Co., Ltd. Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898 Renesas Electronics Hong Kong Limited Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong Tel: +852-2886-9318, Fax: +852 2886-9022/9044 Renesas Electronics Taiwan Co., Ltd. 13F, No. 363, Fu Shing North Road, Taipei, Taiwan Tel: +886-2-8175-9600, Fax: +886 2-8175-9670 Renesas Electronics Singapore Pte. Ltd. 1 harbourFront Avenue, #06-10, keppel Bay Tower, Singapore 098632 Tel: +65-6213-0200, Fax: +65-6278-8001 Renesas Electronics Malaysia Sdn.Bhd. Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: +60-3-7955-9390, Fax: +60-3-7955-9510 Renesas Electronics Korea Co., Ltd. 11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, Korea Tel: +82-2-558-3737, Fax: +82-2-558-5141 (c) 2011 Renesas Electronics Corporation. All rights reserved. Colophon 1.1