VN7007AH High-side driver with CurrentSense analog feedback for automotive applications Datasheet - production data Load current limitation Self limiting of fast thermal transients Loss of ground and loss of VCC Reverse battery Electrostatic discharge protection Applications Features Max transient supply voltage VCC 40 V Operating voltage range VCC 4 to 28 V Typ. on-state resistance (per Ch) RON 7 m Current limitation (typ) ILIMH 100 A Stand-by current (max) ISTBY 0.5 A AEC-Q100 qualified General Single channel smart high-side driver with CurrentSense analog feedback Very low standby current Compatible with 3.0 V and 5 V CMOS outputs Diagnostic functions Overload and short to ground (power limitation) indication Thermal shutdown indication OFF-state open-load detection Output short to VCC detection Sense enable/ disable Protections Undervoltage shutdown Overvoltage clamp November 2016 Specially intended for Automotive smart power distribution, glow plugs, heating systems, DC motors, relay replacement and high power resistive and inductive actuators. Description The device is a single channel high-side driver manufactured using ST proprietary VIPower(R) technology and housed in the Octapak package. The device is designed to drive 12 V automotive grounded loads through a 3 V and 5 V CMOScompatible interface, providing protection and diagnostics. The device integrates advanced protective functions such as load current limitation, overload active management by power limitation and overtemperature shutdown. A sense enable pin allows OFF-state diagnosis to be disabled during the module low-power mode as well as external sense resistor sharing among similar devices. Table 1: Device summary Order codes Package Octapak DocID027957 Rev 3 This is information on a product in full production. Tape and reel VN7007AHTR 1/36 www.st.com Contents VN7007AH Contents 1 Block diagram and pin description ................................................ 5 2 Electrical specification .................................................................... 7 3 4 2.1 Absolute maximum ratings ................................................................ 7 2.2 Thermal data ..................................................................................... 8 2.3 Electrical characteristics .................................................................... 8 2.4 Electrical characteristics curves ...................................................... 15 Protections..................................................................................... 19 3.1 Power limitation ............................................................................... 19 3.2 Thermal shutdown ........................................................................... 19 3.3 Current limitation ............................................................................. 19 3.4 Negative voltage clamp ................................................................... 19 Application information ................................................................ 20 4.1 Protection against reverse battery................................................... 20 4.2 Immunity against transient electrical disturbances .......................... 21 4.3 MCU I/Os protection ........................................................................ 21 4.4 CS - analog current sense .............................................................. 22 4.4.1 Principle of CurrentSense signal generation .................................... 23 4.4.2 Short to VCC and OFF-state open-load detection ........................... 25 5 Maximum demagnetization energy (Vcc = 16 V) ......................... 27 6 Package and PCB thermal data .................................................... 28 6.1 7 8 2/36 Octapak thermal data ...................................................................... 28 Package information ..................................................................... 31 7.1 Octapak package information.......................................................... 31 7.2 Octapak packing information ........................................................... 32 7.3 Octapak marking information .......................................................... 34 Revision history ............................................................................ 35 DocID027957 Rev 3 VN7007AH List of tables List of tables Table 1: Device summary ........................................................................................................................... 1 Table 2: Pin functions ................................................................................................................................. 5 Table 3: Suggested connections for unused and not connected pins ........................................................ 6 Table 4: Absolute maximum ratings ........................................................................................................... 7 Table 5: Thermal data ................................................................................................................................. 8 Table 6: Power section ............................................................................................................................... 8 Table 7: Switching....................................................................................................................................... 9 Table 8: Logic inputs ................................................................................................................................. 10 Table 9: Protection .................................................................................................................................... 10 Table 10: CurrentSense ............................................................................................................................ 11 Table 11: Truth table ................................................................................................................................. 15 Table 12: ISO 7637-2 - electrical transient conduction along supply line ................................................. 21 Table 13: CurrentSense pin levels in off-state .......................................................................................... 25 Table 14: PCB properties ......................................................................................................................... 28 Table 15: Thermal parameters ................................................................................................................. 30 Table 16: Octapak mechanical data ......................................................................................................... 31 Table 17: Reel dimensions ....................................................................................................................... 33 Table 18: Document revision history ........................................................................................................ 35 DocID027957 Rev 3 3/36 List of figures VN7007AH List of figures Figure 1: Block diagram .............................................................................................................................. 5 Figure 2: Configuration diagram (top view)................................................................................................. 6 Figure 3: Current and voltage conventions ................................................................................................. 7 Figure 4: IOUT/ISENSE versus IOUT ....................................................................................................... 13 Figure 5: Current sense precision vs. IOUT ............................................................................................. 13 Figure 6: Switching times and Pulse skew ............................................................................................... 14 Figure 7: tDSTKON ................................................................................................................................... 14 Figure 8: OFF-state output current ........................................................................................................... 15 Figure 9: Standby current ......................................................................................................................... 15 Figure 10: IGND(ON) vs Tcase ................................................................................................................ 16 Figure 11: Logic Input high level voltage .................................................................................................. 16 Figure 12: Logic Input low level voltage.................................................................................................... 16 Figure 13: High level logic input current ................................................................................................... 16 Figure 14: Low level logic input current .................................................................................................... 16 Figure 15: Logic Input hysteresis voltage ................................................................................................. 16 Figure 16: Undervoltage shutdown ........................................................................................................... 17 Figure 17: On-state resistance vs Tcase .................................................................................................. 17 Figure 18: On-state resistance vs VCC .................................................................................................... 17 Figure 19: Turn-on voltage slope .............................................................................................................. 17 Figure 20: Turn-off voltage slope .............................................................................................................. 17 Figure 21: Won vs Tcase .......................................................................................................................... 17 Figure 22: Woff vs Tcase .......................................................................................................................... 18 Figure 23: ILIMH vs. Tcase ....................................................................................................................... 18 Figure 24: Turn-off output voltage clamp .................................................................................................. 18 Figure 25: OFF-state open-load voltage detection threshold ................................................................... 18 Figure 26: Vsense clamp vs. Tcase.......................................................................................................... 18 Figure 27: Vsenseh vs. Tcase .................................................................................................................. 18 Figure 28: Application diagram ................................................................................................................. 20 Figure 29: Simplified internal structure ..................................................................................................... 20 Figure 30: CurrentSense and diagnostic - block diagram........................................................................ 22 Figure 31: CurrentSense block diagram ................................................................................................... 23 Figure 32: Analogue HSD - open-load detection in off-state ................................................................... 24 Figure 33: Open-load / short to VCC condition ......................................................................................... 25 Figure 34: Maximum turn off current versus inductance .......................................................................... 27 Figure 35: Octapak on two-layers PCB (2s0p to JEDEC JESD 51-5) ...................................................... 28 Figure 36: Octapak on four-layers PCB (2s2p to JEDEC JESD 51-7) ..................................................... 28 Figure 37: Rthj-amb vs PCB copper area in open box free air conditions ............................................... 29 Figure 38: Octapak thermal impedance junction ambient single pulse .................................................... 29 Figure 39: Thermal fitting model for Octapak ........................................................................................... 30 Figure 40: Octapak package dimensions ................................................................................................. 31 Figure 41: Octapack reel 13" .................................................................................................................... 32 Figure 42: Octapak carrier tape ................................................................................................................ 33 Figure 43: Octapak schematic drawing of leader and trailer tape ............................................................ 34 Figure 44: Octapak marking information................................................................................................... 34 4/36 DocID027957 Rev 3 VN7007AH 1 Block diagram and pin description Block diagram and pin description Figure 1: Block diagram V CC Reverse Battery Protection Signal Clamp Undervoltage IN Control & Diagnostic Power Clamp DRIVER VON Limitation Over temperature Current Limitation OFF State Open load SEn V SENSEH CS Current Sense LOGIC OUT OVERLOAD PROTECTION ( ACTIVE POWER LIMI TATION ) GND Table 2: Pin functions Name VCC OUTPUT GND Function Battery connection. Power outputs. All the pins must be connected together. Ground connection. INPUT Voltage controlled input pin with hysteresis. Compatible with 3 V and 5 V CMOS outputs. It controls output switch state. CS Analog current sense output pin delivers a current proportional to the load current. SEn Active high compatible with 3 V and 5 V CMOS outputs pin; it enables the CurrentSense diagnostic pin. DocID027957 Rev 3 5/36 Block diagram and pin description VN7007AH GND CS SE n INPUT OUTPUT OUTPUT OUTPUT Figure 2: Configuration diagram (top view) Table 3: Suggested connections for unused and not connected pins Connection / pin CurrentSense N.C. Output Input SEn Floating Not allowed X (1) X X X To ground Through 1 k resistor X Not allowed Through 15 k resistor Through 15 k resistor Notes: (1)X: 6/36 do not care. DocID027957 Rev 3 VN7007AH 2 Electrical specification Electrical specification Figure 3: Current and voltage conventions VF = VOUT - VCC when VOUT > VCC and INPUT = LOW 2.1 Absolute maximum ratings Stressing the device above the rating listed in Table 4: "Absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to the conditions in table below for extended periods may affect device reliability. Table 4: Absolute maximum ratings Symbol Parameter Value Unit VCC DC supply voltage 38 -VCC Reverse DC supply voltage 16 VCCPK Maximum transient supply voltage (ISO7637-2:2004 Pulse 5b level IV clamped to 40 V; RL = 4) 40 VCCJS Maximum jump start voltage for single pulse short circuit protection 28 -IGND DC reverse ground pin current 200 mA IOUT OUTPUT DC output current Internally limited A -IOUT Reverse DC output current 30 IIN INPUT DC input current ISEn SEn DC input current ISENSE -1 to 10 CS pin DC output current (VGND = VCC and VSENSE < 0 V) 10 CS pin DC output current in reverse (VCC < 0 V) -20 DocID027957 Rev 3 V mA mA 7/36 Electrical specification VN7007AH Symbol Parameter Unit EMAX Maximum switching energy (single pulse) TDEMAG = 0.4 ms; Tjstart = 150C 170 mJ VESD Electrostatic discharge (JEDEC 22A-114F) INPUT CurrentSense SEn OUTPUT VCC 4000 2000 4000 4000 4000 V V V V V VESD Charge device model (CDM-AEC-Q100-011) 750 V Tj Tstg 2.2 Value Junction operating temperature -40 to 150 Storage temperature -55 to 150 C Thermal data Table 5: Thermal data Symbol Parameter Typ. value Rthj-board Thermal resistance junction-board (JEDEC JESD 51-8) (1) 2.8 Rthj-amb Thermal resistance junction-ambient (JEDEC JESD 51-2) (2) 58.3 Rthj-amb Thermal resistance junction-ambient (JEDEC JESD 51-2) (1) 15.8 Unit C/W Notes: 2.3 (1)Device mounted on four-layers 2s2p PCB (2)Device mounted on two-layers 2s0p PCB with 2 cm2 heatsink copper trace Electrical characteristics 7 V < VCC < 28 V; -40C < Tj < 150C, unless otherwise specified. All typical values refer to VCC = 13 V; Tj = 25 C, unless otherwise specified. Table 6: Power section Symbol Parameter Test conditions Min. Typ. Max. 4 13 28 VCC Operating supply voltage VUSD Undervoltage shutdown 4 VUSDReset Undervoltage shutdown reset 5 V VUSDhyst Undervoltage shutdown hysteresis IOUT = 6 A; Tj = 150 C 14.3 m IOUT = 6 A; VCC = 4 V; Tj = 25 C 10.5 0.3 IOUT = 6 A; Tj = 25 C RON RON_Rev Vclamp 8/36 Unit On-state resistance RDSON in reverse battery condition VCC = -13 V; IOUT = -6 A; Tj = 25 C Clamp voltage IS = 20 mA; Tj = -40 C DocID027957 Rev 3 7 7 38 m V VN7007AH Electrical specification Symbol Parameter Test conditions IS = 20 mA; 25 C < Tj < 150 C ISTBY tD_STBY IS(ON) IGND(ON) IL(off) VF Supply current in standby at VCC = 13 V (1) Max. 41 46 52 Unit 0.5 A VCC = 13 V; VIN = VOUT = VSEn = 0 V; Tj = 85 C (2) 0.5 A VCC = 13 V; VIN = VOUT = VSEn = 0 V; Tj = 125 C 3 A 300 550 s 3 6.5 mA 9 mA VCC = 13 V; VIN = 5 V; VSEn = 0 V; IOUT = 0 A Supply current VCC = 13 V; VSEn = 0 V; VIN = 5 V; IOUT = 0 A Control stage current consumption in ON-state. All channels active. VCC = 13 V; VSEn = 5 V; VIN = 5 V; IOUT = 6 A Output - VCC diode voltage Typ. VCC = 13 V; VIN = VOUT = VSEn = 0 V; Tj = 25C Standby mode blanking time Off-state output current at VCC = 13 V Min. 60 VIN = VOUT = 0 V; VCC = 13 V; Tj = 25 C 0 VIN = VOUT = 0 V; VCC = 13 V; Tj = 125 C 0 0.01 0.5 A 3 IOUT = -6 A; Tj = 150 C 0.7 V Unit Notes: (1)PowerMOS (2)Parameter leakage included. specified by design; not subject to production test. Table 7: Switching VCC = 13 V; -40 C < Tj < 150 C, unless otherwise specified Symbol Parameter td(on)(1) Turn-on delay time at Tj = 25 C td(off)(1) Turn-off delay time at Tj = 25 C Test conditions RL = 2.2 Min. Typ. Max. 10 65 120 10 55 100 0.1 0.36 0.8 0.1 0.47 0.8 s (dVOUT/dt)on(1) Turn-on voltage slope at Tj = 25 C (dVOUT/dt)off(1) Turn-off voltage slope at Tj = 25 C WON Switching energy losses at turn-on (twon) RL = 2.2 -- 0.6 1.7(2) mJ WOFF Switching energy losses at turn-off (twoff) RL = 2.2 -- 0.6 1.7(2) mJ Differential Pulse skew (tPHL - tPLH) RL = 2.2 -65 -15 35 s tSKEW (1) RL = 2.2 V/s Notes: (1)See Figure 6: "Switching times and Pulse skew" (2)Parameter guaranteed by design and characterization; not subject to production test. DocID027957 Rev 3 9/36 Electrical specification VN7007AH Table 8: Logic inputs 7 V < VCC < 28 V; -40 C < Tj < 150 C Symbol Parameter Test conditions Min. Typ. Max. Unit VIN = 0.9 V 1 A 2.1 V INPUT characteristics VIL Input low level voltage IIL Low level input current VIH Input high level voltage IIH High level input current VI(hyst) Input hysteresis voltage VICL 0.9 VIN = 2.1 V 10 0.2 IIN = 1 mA Input clamp voltage A V 5.3 IIN = -1 mA V 7.5 -0.7 V SEn characteristics (7 V < VCC < 18 V) VSEnL Input low level voltage ISEnL Low level input current VSEnH Input high level voltage ISEnH High level input current VSEn(hyst) Input hysteresis voltage VSEnCL 0.9 VIN = 0.9 V 1 A 2.1 V VIN = 2.1 V 10 0.2 IIN = 1 mA Input clamp voltage V V 5.3 IIN = -1 mA A 7.5 -0.7 V Table 9: Protection 7 V < VCC < 18 V; -40 C < Tj < 150 C Symbol Parameter Test conditions ILIMH(1) DC short circuit current ILIML Short circuit current during thermal cycling TTSD Shutdown temperature TR Reset temperature(2) TRS Thermal reset of fault diagnostic indication Thermal hysteresis (TTSD - TR)(2) TJ_SD Dynamic temperature VDEMAG Turn-off output voltage clamp Output voltage drop limitation Typ. Max. 70 100 140 4 V < VCC < 18 V (2) 140 VCC = 13 V; TR < Tj < TTSD VSEn = 5 V THYST VON VCC = 13 V Min. A 33 150 175 TRS + 1 TRS + 7 200 C 135 7 Tj = -40 C; VCC = 13 V 60 IOUT = 2 A; L = 6 mH; Tj = -40 C VCC 38 IOUT = 2 A; L = 6 mH; Tj = 25 C to 150 C VCC 41 IOUT = 1.2 A Notes: 10/36 Unit (1)Parameter guaranteed by an indirect test sequence. (2)Parameter guaranteed by design and characterization; not subject to production test. DocID027957 Rev 3 K V VCC 46 20 VCC 52 V mV VN7007AH Electrical specification Table 10: CurrentSense 7 V < VCC < 18 V; -40 C < Tj < 150 C Symbol VSENSE_CL Parameter Test conditions CurrentSense clamp voltage VSEn = 0 V; ISENSE = 1 mA Min. Typ. -17 VSEn = 0 V; ISENSE = -1 mA Max. Unit -12 V 7 V Current Sense characteristics KOL1 IOUT/ISENSE IOUT = 10 mA; VSENSE = 0.5 V; VSEn = 5 V KOL2 IOUT/ISENSE IOUT = 0.25 A; VSENSE = 0.5 V; VSEn = 5 V K0 IOUT/ISENSE IOUT = 1 A; VSENSE = 4 V; VSEn = 5 V 3390 Current sense ratio drift IOUT = 1 A; VSENSE = 4 V; VSEn = 5 V -25 IOUT/ISENSE IOUT = 4.6 A; VSENSE = 4 V; VSEn = 5 V 4080 Current sense ratio drift IOUT = 4.6 A; VSENSE = 4 V; VSEn = 5 V -20 IOUT/ISENSE IOUT = 9 A; VSENSE = 4 V; VSEn = 5 V 4830 Current sense ratio drift IOUT = 9 A; VSENSE = 4 V; VSEn = 5 V -13 IOUT/ISENSE IOUT = 27 A; VSENSE = 4 V; VSEn = 5 V 5600 Current sense ratio drift IOUT = 27 A; VSENSE = 4 V; VSEn = 5 V -8 8 % CurrentSense disabled: VSEn = 0 V; 0 0.5 A CurrentSense disabled; -1 V < VSENSE < 5 V(1) -0.5 0.5 A CurrentSense enabled: VSEn = 5 V; VIN = 5 V; IOUT = 0 A; 0 2 A dK0/K0(1)(2) K1 dK1/K1(1)(2) K2 dK2/K2(1)(2) K3 dK3/K3(1)(2) ISENSE0 CurrentSense leakage current 800 10400 6600 10180 25 6570 9530 20 6350 % 8060 13 6300 % % 7150 VOUT_CSD(1) Output voltage for CurrentSense shutdown VSEn = 5 V; RSENSE = 2.7 k; VIN = 5 V; IOUT = 3 A VSENSE_SAT CurrentSense saturation voltage VCC = 7 V; RSENSE = 2.7 k; VSEn = 5 V; VIN = 5 V; IOUT = 27 A; Tj = 150 C 5 V ISENSE_SAT(1) CS saturation current VCC = 7 V; VSENSE = 4 V; VIN = 5 V; VSEn = 5 V; Tj = 150 C 4 mA Output saturation current VCC = 7 V; VSENSE = 4 V; VIN = 5 V; VSEn = 5 V; Tj = 150 C 45 A IOUT_SAT(1) DocID027957 Rev 3 5 V 11/36 Electrical specification VN7007AH 7 V < VCC < 18 V; -40 C < Tj < 150 C Symbol Parameter Test conditions Min. Typ. Max. Unit 3 4 V -15 A 700 s 60 s 30 s 6.6 V 30 mA 60 s OFF-state diagnostic VOL OFF-state open-load voltage detection threshold VIN = 0 V; VSEn = 5 V 2 IL(off2) OFF-state output sink current VIN = 0 V; VOUT = VOL; Tj = -40 C to 125 C -100 tDSTKON OFF-state diagnostic delay time from falling edge of INPUT (see Figure 7: "tDSTKON") VIN = 5 V to 0 V; VSEn = 5 V; IOUT = 0 A; VOUT = 4 V 100 tD_OL_V Settling time for valid OFF-state open load diagnostic indication from rising edge of SEn VIN = 0 V; VOUT = 4 V; VSEn = 0 V to 5 V tD_VOL OFF-state diagnostic delay time from rising edge of VOUT VIN = 0 V; VSEn = 5 V; VOUT = 0 V to 4 V 350 5 Fault diagnostic feedback (see Table 11: "Truth table") VSENSEH CurrentSense output voltage in fault condition VCC = 13 V; VIN = 0 V; VSEn = 5 V; IOUT = 0 A; VOUT = 4 V; RSENSE = 1 k 5 ISENSEH CurrentSense output current in fault condition VCC = 13 V; VSENSE = 5 V 7 20 CurrentSense timings (current sense mode)(3) tDSENSE1H Current sense settling time from rising edge of SEn VIN = 5 V; VSEn = 0 V to 5 V; RSENSE = 1 k; RL = 2.2 tDSENSE1L Current sense disable delay time from falling edge of SEn VIN = 5 V; VSEn = 5 V to 0 V; RSENSE = 1 k; RL = 2.2 5 20 s tDSENSE2H Current sense settling time from rising edge of INPUT VIN = 0 V to 5 V; VSEn = 5 V; RSENSE = 1 k; RL = 2.2 100 300 s tDSENSE2H Current sense settling time from rising edge of IOUT (dynamic response to a step change of IOUT) VIN = 5 V; VSEn = 5 V; RSENSE = 1 k; ISENSE = 90% of ISENSEMAX; RL = 2.2 200 s Current sense turn-off delay time from falling edge of INPUT VIN = 5 V to 0 V; VSEn = 5 V; RSENSE = 1 k; RL = 2.2 250 s tDSENSE2L Notes: (1)Parameter (2)All values refer to VCC = 13 V; Tj = 25C, unless otherwise specified. (3)Transition 12/36 guaranteed by design and characterization; not subject to production test. delay are measured up to 10% of final conditions. DocID027957 Rev 3 50 VN7007AH Electrical specification Figure 4: IOUT/ISENSE versus IOUT 12000 Max 10000 Min Typ K-factor 8000 6000 4000 2000 0 0 5 10 15 20 25 30 IOUT [A] Figure 5: Current sense precision vs. IOUT 80 70 60 Current sense uncalibrated precision 50 Current sense calibrated precision % 40 30 20 10 0 0 5 10 15 20 25 30 IOUT [A] DocID027957 Rev 3 13/36 Electrical specification VN7007AH Figure 6: Switching times and Pulse skew Figure 7: tDSTKON 14/36 DocID027957 Rev 3 VN7007AH Electrical specification Table 11: Truth table Mode 2.4 Conditions INX SEn OUTX Current Sense Comments Standby All logic inputs low L L L Hi-Z Low quiescent current consumption Nominal load connected; Tj < 150C L H L 0 Normal H L H Hi-Z H H H ISENSE = 1/K * IOUT H L H Hi-Z H H H VSENSEH Output cycles with temperature hysteresis Hi-Z Hi-Z Re-start when VCC > VUSD + VUSDhyst (rising) Overload Overload or short to GND causing: Tj > TTSD or Tj > Tj_SD Undervoltage VCC < VUSD (falling) X X L L OFF-state diagnostics Short to VCC L H H Open-load L H H Negative output voltage Inductive loads turn-off L X <0V VSENSEH External pull-up 0 Electrical characteristics curves Figure 8: OFF-state output current Figure 9: Standby current Iloff [nA] ISTBY [A] 400 0 5 4.5 350 0 4 300 0 Off State Vcc = 13V Vin = Vout = 0 250 0 Vcc = 13V 3.5 3 200 0 2.5 2 150 0 1.5 100 0 1 500 0.5 0 0 -50 -25 0 25 50 75 100 125 150 175 T [C] -50 -25 0 25 50 75 100 125 150 175 T [C] DocID027957 Rev 3 15/36 Electrical specification VN7007AH Figure 10: IGND(ON) vs Tcase Figure 11: Logic Input high level voltage ViH, VSE nH [V] IGND (ON) [mA] 5.0 2 4.5 1.8 1.6 4.0 1.4 3.5 Vcc = 13V Iou t = 6A 3.0 1.2 2.5 1 2.0 0.8 1.5 0.6 1.0 0.4 0.5 0.2 0 0.0 -50 -25 0 25 50 75 100 125 150 -50 175 -25 0 25 50 75 100 125 150 175 T [C] T [C] Figure 12: Logic Input low level voltage Figure 13: High level logic input current IiH, ISE nH [A] ViL, VSE nL [V] 4 2 1.8 3.5 1.6 3 1.4 2.5 1.2 2 1 0.8 1.5 0.6 1 0.4 0.5 0.2 0 0 -50 -25 0 25 50 75 100 125 150 -50 175 -25 0 25 50 75 100 125 150 175 T [C] T [C] Figure 14: Low level logic input current Figure 15: Logic Input hysteresis voltage Vi(hyst), VSE n(hyst) [V] IiL, ISE nL [A] 1 4 0.9 3.5 0.8 3 0.7 2.5 0.6 2 0.5 0.4 1.5 0.3 1 0.2 0.5 0.1 0 0 -50 -25 0 25 50 75 100 125 150 175 T [C] 16/36 -50 -25 0 25 50 T [C] DocID027957 Rev 3 75 100 125 150 175 VN7007AH Electrical specification Figure 16: Undervoltage shutdown Figure 17: On-state resistance vs Tcase VUSD [V] Ron [mOhm] 8 30 7 25 6 20 5 Iou t = 6A Vcc = 13V 4 15 3 10 2 5 1 0 0 -50 -25 0 25 50 75 100 125 150 175 -50 -25 0 25 T [C] 50 75 100 125 150 175 T [C] Figure 18: On-state resistance vs VCC Figure 19: Turn-on voltage slope (dVou t/dt)On [V/s] Ron [mOhm] 1 16 0.9 14 12 T = 150 C 0.8 T = 125 C 0.7 10 Vcc = 13V Rl = 2.2 0.6 0.5 8 T = 25 C 0.4 6 T = -40 C 0.3 4 0.2 2 0.1 0 0 0 5 10 15 20 25 30 35 40 -50 -25 0 25 50 Vcc [V] 75 100 125 150 175 150 175 T [C] Figure 20: Turn-off voltage slope Figure 21: Won vs Tcase Won [mJ] (dVou t/dt)Off [V/s] 2 1 0.9 1.6 0.8 Vcc = 13V Rl = 2.2 0.7 1.2 0.6 0.5 0.8 0.4 0.3 0.4 0.2 0.1 0 0 -50 -25 0 25 50 75 100 125 150 175 -50 -25 0 25 50 75 100 125 T [C] T [C] DocID027957 Rev 3 17/36 Electrical specification VN7007AH Figure 23: ILIMH vs. Tcase Figure 22: Woff vs Tcase W off [mJ] Ilimh [A] 2 140 135 1.6 130 125 1.2 120 Vcc = 13V 0.8 115 110 0.4 105 100 0 -50 -25 0 25 50 75 100 125 150 -50 175 -25 0 25 50 75 100 125 150 175 T [C] T [C] Figure 25: OFF-state open-load voltage detection threshold Figure 24: Turn-off output voltage clamp VDEMAG [V] VOL [V] -38 4 -39 -40 3.5 -41 3 -42 -43 2.5 -44 -45 2 Vcc = 13V -46 -47 1.5 -48 -49 1 -50 0.5 -51 -52 -50 -25 0 25 50 75 100 125 150 0 175 -50 T [C] -25 0 25 50 75 100 125 150 175 T [C] Figure 26: Vsense clamp vs. Tcase Figure 27: Vsenseh vs. Tcase VSE NSE_CL [V] VSE NSEH [V] 10 10 9 5 8 Iin = -1mA 7 0 6 5 -5 4 3 -10 2 Iin = 1mA 1 -15 0 -50 -25 0 25 50 75 100 125 150 175 T [C] 18/36 -50 -25 0 25 50 75 T [C] DocID027957 Rev 3 100 125 150 175 VN7007AH Protections 3 Protections 3.1 Power limitation The basic working principle of this protection consists of an indirect measurement of the junction temperature swing Tj through the direct measurement of the spatial temperature gradient on the device surface in order to automatically shut off the output MOSFET as soon as Tj exceeds the safety level of T j_SD. The protection prevents fast thermal transient effects and, consequently, reduces thermo-mechanical fatigue. 3.2 Thermal shutdown In case the junction temperature of the device exceeds the maximum allowed threshold (typically 175C), it automatically switches off and the diagnostic indication is triggered. The device switches on again as soon as its junction temperature drops to T R. 3.3 Current limitation The device is equipped with an output current limiter in order to protect the silicon as well as the other components of the system (e.g. bonding wires, wiring harness, connectors, loads, etc.) from excessive current flow. Consequently, in case of short circuit, overload or during load power-up, the output current is clamped to a safety level, ILIMH, by operating the output power MOSFET in the active region. 3.4 Negative voltage clamp In case the device drives inductive load, the output voltage reaches negative value during turn off. A negative voltage clamp structure limits the maximum negative voltage to a certain value, VDEMAG, allowing the inductor energy to be dissipated without damaging the device. DocID027957 Rev 3 19/36 Application information 4 VN7007AH Application information Figure 28: Application diagram 4.1 Protection against reverse battery Figure 29: Simplified internal structure 20/36 DocID027957 Rev 3 VN7007AH Application information The device does not need any external components to protect the internal logic in case of a reverse battery condition. The protection is provided by internal structures. In addition, due to the fact that the output MOSFET turns on even in reverse battery mode, thus providing the same low ohmic path as in regular operating conditions, no additional power dissipation has to be considered. 4.2 Immunity against transient electrical disturbances The immunity of the device against transient electrical emissions, conducted along the supply lines and injected into the VCC pin, is tested in accordance with ISO7637-2:2011 (E) and ISO 16750-2:2010. The related function performance status classification is shown in Table 12: "ISO 7637-2 electrical transient conduction along supply line". Test pulses are applied directly to DUT (Device Under Test) both in ON and OFF-state and in accordance to ISO 7637-2:2011(E), chapter 4. The DUT is intended as the present device only, without components and accessed through VCC and GND terminals. Status II is defined in ISO 7637-1 Function Performance Status Classification (FPSC) as follows: "The function does not perform as designed during the test but returns automatically to normal operation after the test". Table 12: ISO 7637-2 - electrical transient conduction along supply line Test Pulse 2011(E) Test pulse severity level with Status II functional performance status Minimum number of pulses or test time Burst cycle / pulse repetition time Pulse duration and pulse generator internal impedance Level US(1) 1 III -112V 500 pulses 0,5 s 2a III +55V 500 pulses 0,2 s 5s 50s, 2 3a IV -220V 1h 90 ms 100 ms 0.1s, 50 3b IV +150V 1h 90 ms 100 ms 0.1s, 50 4(2) IV -7V 1 pulse min max 2ms, 10 100ms, 0.01 Load dump according to ISO 16750-2:2010 Test B(3) 40V 5 pulse 1 min 400ms, 2 Notes: (1)U S 4.3 is the peak amplitude as defined for each test pulse in ISO 7637-2:2011(E), chapter 5.6. (2)Test pulse from ISO 7637-2:2004(E). (3)With 40 V external suppressor referred to ground (-40C < Tj < 150C). MCU I/Os protection If a ground protection network is used and negative transients are present on the V CC line, the control pins will be pulled negative. ST suggests to insert a resistor (Rprot) in line both to prevent the microcontroller I/O pins from latch-up and to protect the HSD inputs. The value of these resistors is a compromise between the leakage current of microcontroller and the current required by the HSD I/Os (Input levels compatibility) with the latch-up limit of microcontroller I/Os. DocID027957 Rev 3 21/36 Application information VN7007AH Equation VCCpeak/Ilatchup Rprot (VOHC-VIH-VGND) / IIHmax Calculation example: For VCCpeak = -150 V; Ilatchup 20mA; VOHC 4.5V 7.5 k Rprot 140 k. Recommended values: Rprot = 15 k 4.4 CS - analog current sense Diagnostic information on device and load status are provided by an analog output pin (CS) delivering the following signal: Current monitor: current monitor of channel output current Figure 30: CurrentSense and diagnostic - block diagram 22/36 DocID027957 Rev 3 VN7007AH 4.4.1 Application information Principle of CurrentSense signal generation Figure 31: CurrentSense block diagram Current sense This output is capable of providing: Current mirror proportional to the load current in normal operation, delivering current proportional to the load according to known ratio named K Diagnostics flag in fault conditions delivering fixed voltage V SENSEH The current delivered by the current sense circuit, ISENSE, can be easily converted to a voltage VSENSE by using an external sense resistor, RSENSE, allowing continuous load monitoring and abnormal condition detection. Normal operation (channel ON, no fault, SEn active) While device is operating in normal conditions (no fault intervention), V SENSE calculation can be done using simple equations Current provided by CurrentSense output: ISENSE = IOUT/K Voltage on RSENSE: VSENSE = RSENSE * ISENSE = RSENSE * IOUT/K DocID027957 Rev 3 23/36 Application information Where : VN7007AH VSENSE is voltage measurable on RSENSE resistor ISENSE is current provided from CS pin in current output mode IOUT is current flowing through output K factor represents the ratio between PowerMOS cells and SenseMOS cells; its spread includes geometric factor spread, current sense amplifier offset and process parameters spread of overall circuitry specifying ratio between IOUT and ISENSE. Failure flag indication In case of power limitation/overtemperature, the fault is indicated by the CS pin which is switched to a "current limited" voltage source, VSENSEH . In any case, the current sourced by the CS in this condition is limited to ISENSEH Figure 32: Analogue HSD - open-load detection in off-state 24/36 DocID027957 Rev 3 VN7007AH Application information Figure 33: Open-load / short to VCC condition Table 13: CurrentSense pin levels in off-state Condition Output CurrentSense SEn Hi-Z L VSENSEH H Hi-Z L 0 H Hi-Z L VSENSEH H Hi-Z L 0 H VOUT > VOL Open-load VOUT < VOL Short to VCC Nominal 4.4.2 VOUT > VOL VOUT < VOL Short to VCC and OFF-state open-load detection Short to VCC A short circuit between VCC and output is indicated by the relevant current sense pin set to VSENSEH during the device off-state. Small or no current is delivered by the current sense during the on-state depending on the nature of the short circuit. OFF-state open-load with external circuitry Detection of an open-load in off mode requires an external pull-up resistor RPU connecting the output to a positive supply voltage VPU. DocID027957 Rev 3 25/36 Application information VN7007AH It is preferable VPU to be switched off during the module standby mode in order to avoid the overall standby current consumption to increase in normal conditions, i.e. when load is connected. RPU must be selected in order to ensure VOUT > VOLmax in accordance with the following equation: Equation 26/36 DocID027957 Rev 3 VN7007AH Maximum demagnetization energy (Vcc = 16 V) Figure 34: Maximum turn off current versus inductance VN7007Ax - Maximum turn off current versus inductance 100 10 I (A) 5 Maximum demagnetization energy (Vcc = 16 V) 1 VN7007Ax - Single Pulse Repetitive pulse Tjstart=100C Repetitive pulse Tjstart=125C 0.1 0.1 1 10 L (mH) 100 1000 Values are generated with RL = 0 . In case of repetitive pulses, Tjstart (at the beginning of each demagnetization) of every pulse must not exceed the temperature specified above for curves A and B. DocID027957 Rev 3 27/36 Package and PCB thermal data VN7007AH 6 Package and PCB thermal data 6.1 Octapak thermal data Figure 35: Octapak on two-layers PCB (2s0p to JEDEC JESD 51-5) Figure 36: Octapak on four-layers PCB (2s2p to JEDEC JESD 51-7) Table 14: PCB properties Dimension Board finish thickness 1.6 mm +/- 10% Board dimension 77 mm x 86 mm Board Material FR4 Copper thickness (top and bottom layers) 0.070 mm Copper thickness (inner layers) 0.035 mm Thermal vias separation 1.2 mm Thermal via diameter 0.3 mm +/- 0.08 mm Copper thickness on vias 0.025 mm Footprint dimension (top layer) 6.4 mm x 7mm Heatsink copper area dimension (bottom layer) 28/36 Value DocID027957 Rev 3 Footprint, 2 cm2 or 8 cm2 VN7007AH Package and PCB thermal data Figure 37: Rthj-amb vs PCB copper area in open box free air conditions RTHjamb 80 75 RTHjamb 70 65 60 55 50 45 40 35 30 0 2 4 6 8 10 Figure 38: Octapak thermal impedance junction ambient single pulse ZTH (C/W) 100 Cu=foot print Cu=2 cm2 Cu=8 cm2 10 4Layer 1 0.1 0.01 0.000 1 0.001 0.01 0.1 1 10 100 100 0 Time (s) Equation: Pulse calculation formula ZTH = RTH * + ZTHtp (1 - ) where = tP/T DocID027957 Rev 3 29/36 Package and PCB thermal data VN7007AH Figure 39: Thermal fitting model for Octapak The fitting model is a simplified thermal tool and is valid for transient evolutions where the embedded protections (power limitation or thermal cycling during thermal shutdown) are not triggered. Table 15: Thermal parameters 30/36 Area/island (cm2) Footprint 2 8 4L R1 (C/W) 0.2 0.2 0.2 0.2 R2 (C/W) 0.7 0.7 0.7 0.7 R3 (C/W) 1.4 1.4 1.4 1.4 R4 (C/W) 10 10 10 2.5 R5 (C/W) 28 20 12 5 R6 (C/W) 36 26 18 6 C1 (W.s/C) 0.0015 0.0015 0.0015 0.0015 C2 (W.s/C) 0.013 0.013 0.013 0.013 C3 (W.s/C) 0.15 0.15 0.15 0.15 C4 (W.s/C) 0.6 0.6 0.6 0.8 C5 (W.s/C) 0.8 1.4 2.2 3 C6 (W.s/C) 3 6 9 25 DocID027957 Rev 3 VN7007AH 7 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK (R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. 7.1 Octapak package information Figure 40: Octapak package dimensions Table 16: Octapak mechanical data Millimeters Symbol Min. Typ. Max. A 2.20 2.30 2.40 A1 0.90 1.00 1.10 A2 0.03 b 0.38 DocID027957 Rev 3 0.15 0.45 0.52 31/36 Package information VN7007AH Millimeters Symbol Min. Typ. b1 0.70 b4 5.20 5.30 5.40 c 0.45 0.50 0.60 c2 0.75 0.80 0.90 D 6.00 6.10 6.20 D1 E 5.15 6.40 E1 6.50 0.85 BSC e1 1.60 1.70 1.80 e2 3.30 3.40 3.50 e3 5.00 5.10 5.20 H 9.35 9.70 10.10 L 1.00 -- (L1) 2.80 L2 0.80 L3 0.85 R V2 0.40 BSC 0 Octapak packing information Figure 41: Octapack reel 13" 32/36 6.60 5.30 e 7.2 Max. DocID027957 Rev 3 8 VN7007AH Package information Table 17: Reel dimensions Description Value(1) Base quantity 2500 Bulk quantity 2500 A (max) 330 B (min) 1.5 C (+0.5, -0.2) 13 D 20.2 N 100 W1 (+2 /-0) 16.4 W2 (max) 22.4 Notes: (1)All dimensions are in mm. Figure 42: Octapak carrier tape DocID027957 Rev 3 33/36 Package information VN7007AH Figure 43: Octapak schematic drawing of leader and trailer tape 7.3 Octapak marking information Figure 44: Octapak marking information Parts marked as "&" are not yet qualified and therefore not yet ready to be used in production and any consequences deriving from such usage will not be at ST charge. In no event, ST will be liable for any customer usage of these engineering samples in production. ST Quality has to be contacted prior to any decision to use these Engineering Samples to run qualification activity. 34/36 DocID027957 Rev 3 VN7007AH 8 Revision history Revision history Table 18: Document revision history Date Revision Changes 17-Jun-2015 1 13-Oct-2015 2 02-Nov-2016 3 Added AEC Q100 qualified in Features section Updated Applications section Initial release Table 10: "CurrentSense": KOL1: updated test conditions DocID027957 Rev 3 35/36 VN7007AH IMPORTANT NOTICE - PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST's terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers' products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. (c) 2016 STMicroelectronics - All rights reserved 36/36 DocID027957 Rev 3