B57364S0509M000 - EPCOS - Product.Network

NTC thermistors for

inrush current limiting

Leaded and coated disks

Series/Type: B57364S0***M0**

Date: October 2011

information contained therein without EPCOS' prior express consent is prohibited.

1) For details on the capacitance Ctest as well as on the parameters k and n refer to "Application notes", chapters 1.6 and 1.7.

Applications

Switch-mode power supplies

Soft-start motors, e.g. in vacuum cleaners

Features

Useable in series connections

up to 265 VRMS

Coated thermistor disk

Kinked leads of tinned copper wire

Wide resistance range

UL approval (E69802)

Options

Resistance tolerance <20% and alternative lead

configurations available on request

Delivery mode

Bulk (standard) or with cardboard tape on 500-mm reel

Dimensional drawing

Dimensions in mm

Approx. weight 4 g

General technical data

Climatic category (IEC 60068-1) 55/170/21

Max. power (at 25 °C) Pmax 5.1 W

Resistance tolerance ∆RR/RR±20 %

Rated temperature TR25 °C

Dissipation factor (in air) δth approx. 24 mW/K

Thermal cooling time constant (in air) τcapprox. 100 s

Heat capacity Cth approx. 2400 mJ/K

Electrical specification and ordering codes

R25

Ω

Imax

(0...65 °C)

B25/100

Ctest1)

230 V AC

µF

Ctest1)

110 V AC

µF

Param.

for R(I)1)

Param.

for R(I)1)

Ordering code

** = Delivery mode

00 = Bulk

51 = Reel packing

1 16.0 2800 1000 4000 0.766 1.30 B57364S0109M0**

2 12.0 2900 1000 4000 0.966 1.32 B57364S0209M0**

2.5 11.0 2900 1000 4000 1.04 1.32 B57364S0259M0**

4 9.5 3060 1000 4000 1.20 1.34 B57364S0409M0**

5 8.5 3060 1000 4000 1.29 1.34 B57364S0509M0**

10 7.5 3300 1000 4000 1.55 1.37 B57364S0100M0**

Inrush current limiters B57364S0***M0**

ICLs S364

Page 2 of 14Please read Cautions and warnings and

Important notes at the end of this document.

Reliability data

Test Standard Test conditions ∆R25/R25

(typical)

Remarks

Storage in

dry heat

IEC

60068-2-2

Storage at upper

category temperature

T: 170 °C

t: 1000 h

< 10% No visible

damage

Storage in damp

heat, steady state

IEC

60068-2-78

Temperature of air: 40 °C

Relative humidity of air: 93%

Duration: 21 days

< 5% No visible

damage

Rapid temperature

cycling

IEC

60068-2-14

Lower test temperature: 55 °C

Upper test temperature: 170 °C

Number of cycles: 10

< 10% No visible

damage

Endurance I = Imax

t: 1000 h

< 10% No visible

damage

Cyclic

endurance

I=Imax, 1000 cycles

On-time = 1 min

Cooling time = 6 min

< 10% No visible

damage

Transient

load

Capacitance = Ctest

Number of cycles: 1000

< 5% No visible

damage

Note

The self-heating of a thermistor during operation depends on the load applied and the

applicable dissipation factor.

When loaded with maximum allowable current/power and the specified dissipation factor is

taken as a basis, the NTC thermistor may reach a mean temperature of up to 250 °C.

The heat developed during operation will also be dissipated through the lead wires. So the

contact areas, too, may become quite hot at maximum load.

When mounting NTC thermistors you have to ensure that there is an adequate distance

between the thermistor and all parts which are sensitive to heat or combustible.

Inrush current limiters B57364S0***M0**

ICLs S364

Page 3 of 14Please read Cautions and warnings and

Important notes at the end of this document.

Taping and packing

1 Taping of radial leaded ICL NTC thermistors according to the

specified lead spacing

Dimensions and tolerances

Lead spacing F = 5.0 mm (taping to IEC 60286-2)

Lead spacing F = 7.5 mm (taping based on IEC 60286-2)

Inrush current limiters B57364S0***M0**

ICLs S364

Page 4 of 14Please read Cautions and warnings and

Important notes at the end of this document.

Dimensions (mm)

Lead

spacing

5 mm

Tolerance of

lead spacing

5 mm

Lead

spacing

7.5 mm

Tolerance of

lead spacing

7.5 mm

Remarks

w≤12.0 max. ≥12.0 max. please refer to dimensional

drawings

th 6.0 max. 7 max. please refer to dimensional

drawings

d 0.5/0.6 ±0.05 0.8/1.0 ±0.05 please refer to dimensional

drawings

P012.7 ±0.3 12.7 ±0.3 ±1 mm / 20 sprocket holes

P13.85 ±0.7 8.95 ±0.8

F 5.0 +0.6/0.1 7.5 ±0.8

∆h 0 ±2.0 0 Depends on th measured at top

of component body

∆p 0 ±1.3 0 ±2.0

W 18.0 ±0.5 18.0 ±0.5

W05.5 min. 11.0 min. peel-off force ≥5 N

W19.0 +0.75/0.5 9.0 +0.75/0.5

W23.0 max. 3.0 max.

H 18.0 +2.0/0 18.0 +2.0/0

H016.0 ±0.5 16.0 ±0.5

H132.2 max. 45.0 max.

D04.0 ±0.2 4.0 ±0.2

t 0.9 max. 0.9 max. without wires

L 11.0 max. 11.0 max.

L14.0 max. 4.0 max.

Inrush current limiters B57364S0***M0**

ICLs S364

Page 5 of 14Please read Cautions and warnings and

Important notes at the end of this document.

Types of packing

Reel packing

Reel dimensions (in mm)

Reel type d f n w

I 360 max. 31 ±1 approx. 45 54 max.

II 500 max. 23 ±1 approx. 59 72 max.

Bulk packing

The components are packed in cardboard boxes, the size of which depends on the order quantity.

Inrush current limiters B57364S0***M0**

ICLs S364

Page 6 of 14Please read Cautions and warnings and

Important notes at the end of this document.

Mounting instructions

1 Soldering

1.1 Leaded NTC thermistors

Leaded thermistors comply with the solderability requirements specified by CECC.

When soldering, care must be taken that the NTC thermistors are not damaged by excessive

heat. The following maximum temperatures, maximum time spans and minimum distances have

to be observed:

Dip soldering Iron soldering

Bath temperature max. 260 °C max. 360 °C

Soldering time max. 4 s max. 2 s

Distance from thermistor min. 6 mm min. 6 mm

Under more severe soldering conditions the resistance may change.

Solderability (test to IEC 60068-2-20)

Preconditioning: Immersion into flux F-SW 32.

Evaluation criterion: Wetting of soldering areas ≥95%.

Solder Bath temperature (°C) Dwell time (s)

SnAg (3.0 ... 4.0), Cu (0.5 ... 0.9) 245 ±3 3

1.1.1 Resistance to soldering heat (test to IEC 60068-2-20)

Preconditioning: Immersion into flux F-SW 32.

Solder Bath temperature (°C) Dwell time (s)

SnAg (3.0 ... 4.0), Cu (0.5 ... 0.9) 260 5 10

Inrush current limiters B57364S0***M0**

ICLs S364

Page 7 of 14Please read Cautions and warnings and

Important notes at the end of this document.

Wave soldering

Temperature characteristic at component terminal with dual wave soldering

2 Robustness of terminations

The leads meet the requirements of IEC 60068-2-21. They may not be bent closer than 4 mm

from the solder joint on the thermistor body or from the point at which they leave the feed-

throughs. During bending, any mechanical stress at the outlet of the leads must be removed. The

bending radius should be at least 0.75 mm.

Tensile strength: Test Ua1:

Leads 0.50 < ∅ ≤0.80 mm = 10.0 N

0.80 < ∅ ≤1.25 mm = 20.0 N

Bending strength: Test Ub:

Two 90°-bends in opposite directions at a weight of 0.25 kg.

Torsional strength: Test Uc: severity 2

The lead is bent by 90°at a distance of 6 to 6.5 mm from the thermistor body.

The bending radius of the leads should be approx. 0.75 mm. Two torsions of

180°each (severity 2).

Inrush current limiters B57364S0***M0**

ICLs S364

Page 8 of 14Please read Cautions and warnings and

Important notes at the end of this document.

When subjecting leads to mechanical stress, the following should be observed:

Tensile stress on leads

During mounting and operation tensile forces on the leads are to be avoided.

Bending of leads

Bending of the leads directly on the thermistor body is not permissible.

A lead may be bent at a minimum distance of twice the wire's diameter +2 mm from the solder

joint on the thermistor body. During bending the wire must be mechanically relieved at its outlet.

The bending radius should be at least 0.75 mm.

Twisting of leads

The twisting (torsion) by 180°of a lead bent by 90°is permissible at 6 mm from the bottom of the

thermistor body.

3 Sealing and potting

When thermistors are sealed, potted or overmolded, there must be no mechanical stress caused

by thermal expansion during the production process (curing / overmolding process) and during

later operation. The upper category temperature of the thermistor must not be exceeded. Ensure

that the materials used (sealing / potting compound and plastic material) are chemically neutral.

4 Cleaning

If cleaning is necessary, mild cleaning agents such as ethyl alcohol and cleaning gasoline are

recommended. Cleaning agents based on water are not allowed. Ultrasonic cleaning methods are

permissible.

5 Storage

In order to maintain their solderability, thermistors must be stored in a non-corrosive atmosphere.

Humidity, temperature and container materials are critical factors.

The components should be left in the original packing. Touching the metallization of unsoldered

thermistors may change their soldering properties.

Storage temperature: 25 °Cupto45°C

Max. relative humidity (without condensation):

<95%, maximum 30 days per annum

Solder the thermistors listed in this data book after shipment from EPCOS within the time speci-

fied:

Leaded components: 24 months

Inrush current limiters B57364S0***M0**

ICLs S364

Page 9 of 14Please read Cautions and warnings and

Important notes at the end of this document.

Cautions and warnings

General

See "Important notes" at the end of this document.

Storage

Store thermistors only in original packaging. Do not open the package before storage.

Storage conditions in original packaging: storage temperature 25 °C ... +45 °C, relative

humidity ≤75% annual mean, maximum 95%, dew precipitation is inadmissible.

Avoid contamination of thermistors surface during storage, handling and processing.

Avoid storage of thermistor in harmful environments like corrosive gases (SOx, Cl etc).

Solder thermistors after shipment from EPCOS within the time specified:

Leaded components: 24 months

Handling

NTC thermistors must not be dropped. Chip-offs must not be caused during handling of NTCs.

Components must not be touched with bare hands. Gloves are recommended.

Avoid contamination of thermistor surface during handling.

In case of exposure of the NTC thermistors to water, electrolytes or other aggressive media,

these media can penetrate the coating and reach the surface of the ceramic. Low-ohmic or

high-ohmic behavior may occur due to the formation of an electrolyte with metals (silver/lead/tin

from metallization or solder). Low-ohmic behavior is caused by electrochemical migration,

high-ohmic behavior by dissolving of the electrode. Ineither case, the functionality of the NTC

thermistors can not be assured.

Bending / twisting leads

A lead (wire) may be bent at a minimum distance of twice the wire’s diameter plus 4 mm from

the component head or housing. When bending ensure the wire is mechanically relieved at the

component head or housing. The bending radius should be at least 0.75 mm.

Twisting (torsion) by 180°of a lead bent by 90°is permissible at 6 mm from the bottom of the

thermistor body.

Soldering

Use resin-type flux or non-activated flux.

Insufficient preheating may cause ceramic cracks.

Rapid cooling by dipping in solvent is not recommended.

Complete removal of flux is recommended.

Inrush current limiters B57364S0***M0**

ICLs S364

Page 10 of 14Please read Cautions and warnings and

Important notes at the end of this document.

Mounting

When NTC thermistors are encapsulated with sealing material or overmolded with plastic

material, the precautions given in chapter “Mounting instructions”, “Sealing and potting” must

be observed.

Electrode must not be scratched before/during/after the mounting process.

Contacts and housings used for assembly with thermistor have to be clean before mounting.

During operation, the inrush current limiters surface temperature can be very high. Ensure that

adjacent components are placed at a sufficient distance from the thermistor to allow for proper

cooling of the thermistors.

Ensure that adjacent materials are designed for operation at temperatures comparable to the

surface temperature of the thermistor. Be sure that surrounding parts and materials can

withstand this temperature.

Make sure that inrush current limiters are adequately ventilated to avoid overheating.

Avoid contamination of thermistor surface during processing.

Operation

Use thermistors only within the specified operating temperature range.

Use inrush current limiters only within the specified voltage and current ranges.

Environmental conditions must not harm the thermistors. Use thermistors only in normal

atmospheric conditions.

Contact of NTC thermistors with any liquids and solvents should be prevented. It must be

ensured that no water enters the NTC thermistor (e.g. through plug terminals). For

measurement purposes (checking the specified resistance vs. temperature), the component

must not be immersed in water but in suitable liquids (e.g. Galden).

In case of exposure of the NTC thermistors to water, electrolytes or other aggressive media,

these media can penetrate the coating and reach the surface of the ceramic. Low-ohmic or

high-ohmic behavior may occur due to the formation of an electrolyte with metals (silver/lead/tin

from metallization or solder). Low-ohmic behavior is caused by electrochemical migration,

high-ohmic behavior by dissolving of the electrode. Ineither case, the functionality of the NTC

thermistorscannot be assured.

Be sure to provide an appropriate fail-safe function to prevent secondary product damage

caused by malfunction (e.g. use a metal oxide varistor for limitation of overvoltage condition).

Inrush current limiters B57364S0***M0**

ICLs S364

Page 11 of 14Please read Cautions and warnings and

Important notes at the end of this document.

Symbols and terms

Symbol English German

Ctest Test capacitance Prüfkapazität (elektrisch)

Cth Heat capacitance Wärmekapazität

I Current Strom

Imax Maximum current within stated

temperature range

Maximalstrom im angegebenen

Temperaturbereich

INTC NTC current Heißleiter-Strom

IRRated current Nennstrom

P25 Maximum power at 25 °C Maximale Leistung bei 25 °C

Pdiss Power dissipation Verlustleistung

Pel Electrical power Elektrische Leistung

Pmax Maximum power within stated

temperature range

Maximale Leistung im

angegebenenTemperaturbereich

RRRated resistance Nennwiderstand

∆RR/RRResistance tolerance Widerstandstoleranz

RTResistance at temperature T

(e.g. R25 = resistance at 25 °C)

Widerstand bei Temperatur T

(z.B. R25 = Widerstand bei 25 °C)

T Temperature Temperatur

t Time Zeit

TAAmbient temperature Umgebungstemperatur

taThermal threshold time Thermische Ansprechzeit

Tmax Upper category temperature Obere Grenztemperatur

(Kategorietemperatur)

Tmin Lower category temperature Untere Grenztemperatur

(Kategorietemperatur)

TRRated temperature Nenntemperatur

V Voltage Spannung

Vload Load voltage Ladespannung

VNTC Voltage drop across an NTC thermistor Spannungsabfall am Heißleiter

αTemperature coefficient Temperaturkoeffizient

∆Tolerance, change Toleranz, Änderung

δth Dissipation factor Wärmeleitwert

τcThermal cooling time constant Thermische Abkühlzeitkonstante

Inrush current limiters B57364S0***M0**

ICLs S364

Page 12 of 14Please read Cautions and warnings and

Important notes at the end of this document.

Abbreviations / Notes

Symbol English German

* To be replaced by a number in ordering

codes, type designations etc.

Platzhalter für Zahl im Bestellnummern-

code oder für die Typenbezeichnung.

+ To be replaced by a letter. Platzhalter für einen Buchstaben.

All dimensions are given in mm. Alle Maße sind in mm angegeben.

The commas used in numerical values

denote decimal points.

Verwendete Kommas in Zahlenwerten

bezeichnen Dezimalpunkte.

Inrush current limiters B57364S0***M0**

ICLs S364

Page 13 of 14Please read Cautions and warnings and

Important notes at the end of this document.

The following applies to all products named in this publication:

1. Some parts of this publication contain statements about the suitability of our products for

certain areas of application. These statements are based on our knowledge of typical re-

quirements that are often placed on our products in the areas of application concerned. We

nevertheless expressly point out that such statements cannot be regarded as binding

statements about the suitability of our products for a particular customer application.

As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar

with them than the customers themselves. For these reasons, it is always ultimately incum-

bent on the customer to check and decide whether an EPCOS product with the properties de-

scribed in the product specification is suitable for use in a particular customer application.

2. We also point out that in individual cases, a malfunction of electronic components or

failure before the end of their usual service life cannot be completely ruled out in the

current state of the art, even if they are operated as specified. In customer applications

requiring a very high level of operational safety and especially in customer applications in

which the malfunction or failure of an electronic component could endanger human life or

health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by

means of suitable design of the customer application or other action taken by the customer

(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by

third parties in the event of malfunction or failure of an electronic component.

3. The warnings, cautions and product-specific notes must be observed.

4. In order to satisfy certain technical requirements, some of the products described in this

publication may contain substances subject to restrictions in certain jurisdictions (e.g.

because they are classed as hazardous). Useful information on this will be found in our Ma-

terial Data Sheets on the Internet (www.epcos.com/material). Should you have any more de-

tailed questions, please contact our sales offices.

5. We constantly strive to improve our products. Consequently, the products described in this

publication may change from time to time. The same is true of the corresponding product

specifications. Please check therefore to what extent product descriptions and specifications

contained in this publication are still applicable before or when you place an order. We also

reserve the right to discontinue production and delivery of products. Consequently, we

cannot guarantee that all products named in this publication will always be available. The

aforementioned does not apply in the case of individual agreements deviating from the fore-

going for customer-specific products.

6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-

sion of the "General Terms of Delivery for Products and Services in the Electrical In-

dustry" published by the German Electrical and Electronics Industry Association

(ZVEI).

7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DeltaCap,

DigiSiMic, DSSP, FormFit, MiniBlue, MiniCell, MKK, MKD, MLSC, MotorCap, PCC,

PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap,

SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trade-

marks registered or pending in Europe and in other countries. Further information will be

found on the Internet at www.epcos.com/trademarks.

Important notes

Page 14 of 14