56.8mm (2.3 INCH) 16 SEGMENT SINGLE DIGIT ALPHANUMERIC DISPLAY P/N: PSA23-11EWA Features z2.3 HIGH EFFICIENCY RED Description INCH CHARACTER HEIGHT. The High Efficiency Red source color devices are CURRENT OPERATION. made with Gallium Arsenide Phosphide on Gallium CONTRAST AND LIGHT OUTPUT. Phosphide Orange Light Emitting Diode. zLOW zHIGH zEASY MOUNTING ON P.C. BOARDS OR SOCKETS. zMECHANICALLY zSTANDARD zRoHS RUGGED. : GRAY FACE, WHITE SEGMENT. COMPLIANT. Package Dimensions & Internal Circuit Diagram Notes: 1. All dimensions are in millimeters (inches), Tolerance is 0.25(0.01")unless otherwise noted. 2. Specifications are subject to change without notice. SPEC NO: DSAD2410 REV NO: V.5 DATE:NOV/26/2005 PAGE: 1 OF 4 APPROVED: J. Lu CHECKED: Joe Lee DRAWN:F.LI ERP: 1311000078 Selection Guide Part No. Dice PSA23-11EWA Iv (ucd) @ 10mA Lens Type HIGH EFFICIENCY RED (GaAsP/GaP) WHITE DIFFUSED Min. Typ. 1900 8000 Description Common Anode, Rt. Hand Decimal. Electrical / Optical Characteristics at TA=25C Symbol peak D 1/2 C Parameter Device Typ. Peak Wavelength High Efficiency Red Dominant Wavelength Units Test Conditions 627 nm IF=20mA High Efficiency Red 625 nm IF=20mA Spectral Line Half-width High Efficiency Red 45 nm IF=20mA Capacitance High Efficiency Red 15 pF VF=0V;f=1MHz High Efficiency Red 4.0 3.8 2.0 A1,A2,D1,D2,P,K VF Forward Voltage B,C,E,F,G,H,J,L,M,N DP Max. A1,A2,D1,D2,P,K IR Reverse Current B,C,E,F,G,H,J,L,M,N High Efficiency Red DP 5.0 5.0 2.5 V 10 20 10 uA IF=20mA VR = 10V VR = 10V VR = 5V Absolute Maximum Ratings at TA=25C Parameter A1,A2,D1,D2,P,K Power dissipation B,C,E,F,G,H,J,L,M,N DP A1,A2,D1,D2,P,K DC Forward Current B,C,E,F,G,H,J,L,M,N DP A1,A2,D1,D2,P,K Peak Forward Current [1] B,C,E,F,G,H,J,L,M,N DP A1,A2,D1,D2,P,K Reverse Voltage B,C,E,F,G,H,J,L,M,N DP Operating / Storage Temperature High Efficiency Red Units 150 300 105 mW 30 60 30 mA 160 320 160 mA 10 10 5 V -40C To +85C Lead Solder Temperature [2] 260C For 5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. SPEC NO: DSAD2410 REV NO: V.5 DATE:NOV/26/2005 PAGE: 2 OF 4 APPROVED: J. Lu CHECKED: Joe Lee DRAWN:F.LI ERP: 1311000078 High Efficiency Red PSA23-11EWA Remarks: If special sorting is required (e.g. binning based on forward voltage, luminous intensity/ luminous flux or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity/ Luminous Flux: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. SPEC NO: DSAD2410 REV NO: V.5 DATE:NOV/26/2005 PAGE: 3 OF 4 APPROVED: J. Lu CHECKED: Joe Lee DRAWN:F.LI ERP: 1311000078 PACKING & LABEL SPECIFICATIONS PSA23-11EWA SPEC NO: DSAD2410 REV NO: V.5 DATE:NOV/26/2005 PAGE: 4 OF 4 APPROVED: J. Lu CHECKED: Joe Lee DRAWN:F.LI ERP: 1311000078