240pin DDR2 SDRAM Unbuffered DIMMs based on 1Gb A ver. This Hynix unbuffered Dual In-Line Memory Module(DIMM) series consists of 1Gb ver.A DDR2 SDRAMs in Fine Ball Grid Array(FBGA) packages on a 240pin glass-epoxy substrate. This Hynix 1Gb ver.A based DDR2 Unbuffered DIMM series provide a high performance 8 byte interface in 133.35mm width form factor of industry standard. It is suitable for easy interchange and addition. FEATURES * JEDEC standard Double Data Rate2 Synchrnous DRAMs (DDR2 SDRAMs) with 1.8V +/- 0.1V Power Supply * All inputs and outputs are compatible with SSTL_1.8 interface * 8 Bank architecture * Posted CAS * Programmable CAS Latency 3 ,4 ,5 * OCD (Off-Chip Driver Impedance Adjustment) * ODT (On-Die Termination) * Fully differential clock operations (CK & CK) * Programmable Burst Length 4 / 8 with both sequential and interleave mode * Auto refresh and self refresh supported * 8192 refresh cycles / 64ms * Serial presence detect with EEPROM * DDR2 SDRAM Package: 68ball FBGA(128Mx8), 92ball FBGA(64Mx16) * 133.35 x 30.00 mm form factor * Lead-free Products are RoHS compliant ORDERING INFORMATION Part Name Density Org. # of DRAMs # of ranks Materials ECC HYMP164U64AP6-E3/C4/Y5/S5 512MB 64Mx64 4 1 Lead-free None HYMP112U64AP8-E3/C4/Y5/S5 1GB 128Mx64 8 1 Lead-free None HYMP112U72AP8-E3/C4/Y5/S5 1GB 128Mx72 9 1 Lead-free ECC HYMP125U64AP8-E3/C4/Y5/S5 2GB 256Mx64 16 2 Lead-free None HYMP125U72AP8-E3/C4/Y5/S5 2GB 256Mx72 18 2 Lead-free ECC This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any responsibility for use of circuits described. No patent licenses are implied. Rev. 0.3 / Nov. 2006 1 1240pin DDR2 SDRAM Unbuffered DIMMs SPEED GRADE & KEY PARAMETERS E3 (DDR2-400) C4 (DDR2-533) Y5 (DDR2-667) S5 (DDR2-800) Unit Speed @CL3 400 400 400 400 Mbps Speed @CL4 400 533 533 533 Mbps Speed @CL5 - - 667 800 Mbps CL-tRCD-tRP 3-3-3 4-4-4 5-5-5 5-5-5 tCK ADDRESS TABLE Density Organization Ranks SDRAMs # of DRAMs # of row/bank/column Address Refresh Method 512MB 64M x 64 1 64Mb x 16 4 13(A0~A12)/3(BA0~BA2)/10(A0~A9) 8K / 64ms 1GB 128M x 64 1 128Mb x 8 8 14(A0~A13)/3(BA0~BA2)/10(A0~A9) 8K / 64ms 1GB 128M x 72 1 128Mb x 8 9 14(A0~A13)/3(BA0~BA2)/10(A0~A9) 8K / 64ms 2GB 256M x 64 2 128Mb x 8 16 14(A0~A13)/3(BA0~BA2)/10(A0~A9) 8K / 64ms 2GB 256M x 72 2 128Mb x 8 18 14(A0~A13)/3(BA0~BA2)/10(A0~A9) 8K / 64ms Rev. 0.3 / Nov 2006 2 1240pin DDR2 SDRAM Unbuffered DIMMs Input/Output Functional Description Symbol CK[2:0], CK[2:0] CKE[1:0] Type SSTL SSTL Polarity Differential Crossing Active High Pin Description CK andk /CK are dirrerential clock inputs. All the DDR2 SDRAM addr/cntl inputs are sampled on the crossing of positive edge of CK and negative edge of /CK. Output(read) data is reference to the crossing of CK and /CK (Both directions of crossing) Activates the DDR2 SDRAM CK signal when high and deactivates the CK signal when low. By deactivating the clocks, CKE low initiates the Power Down mode or the Self Refresh mode. Enables the associated DDR2 SDRAM command decoder when low and disables the S[1:0] SSTL Active Low command decoder when high. When the command decoder is disabled, new commands are ignored but previous operations continue. Rank 0 is selected by S0; Rank 1 is selected by S1 RAS, CAS, SSTL Active Low ODT[1:0] SSTL Active High Vref Supply SDRAM mode register. Reference voltage for SSTL18 inputs Power supplies for the DDR2 SDRAM output buffers to provide improved noise immu- VDDQ Supply nity. For all current DDR2 unbuffered DIMM designs, VDDQ shares the same power plane BA[2:0] SSTL WE /RAS,/CAS and /WE(ALONG WITH S) define the command being entered. Asserts on-die termination for DQ, DM, DQS and DQS signals if enabled via the DDR2 as VDD pins. - Selects which DDR2 SDRAM internal bank of four or eight is activated. During a Bank Activate command cycle, Address input difines the row address(RA0~RA15) During a Read or Write command cycle, Address input defines the column address when sampled at the cross point of the rising edge of CK and falling edge of CK. In addition to A[9:0], A10/AP, A[13:11] SSTL - the column address, AP is used to invoke autoprecharge operation at the end of the burst read or write cycle. If AP is high., autoprecharge is selected and BA0-BAn defines the bank to be precharged. If AP is low, autoprecharge is disabled. During a Precharge command cycle., AP is used in conjunction with BA0-BAn to control which bank(s) to precharge. If AP is high, all banks will be precharged regardless of the state of BA0-BAn inputs. If AP is low, then BA0-BAn are used to define which bank to precharge. DQ[63:0], CB[7:0] SSTL - Data and Check Bit Input/Output pins. DM is an input mask signal for write data. Input data is masked when DM is sampled DM[8:0] VDD,VSS DQS[8:0], DQS[8:0] SSTL Active High pins are tied to VDD/VDDQ planes on these modules. Differential crossing SA[2:0] - SDA - SCL - VDDSPD Supply Rev. 0.3 / Nov 2006 of DQS. Although DM pins are input only, the DM loading matches the DQ and DQS loading. Power and ground for the DDR2 SDRAM input buffers, and core logic. VDD and VDDQ Supply SSTL High coincident with that input data during a write access. DM is sampled on both edges Data strobe for input and output data. For Rawcards using x16 organized DRAMs, DQ0~7 connect to the LDQS pin of the DRAMs and DQ8~15 connect to the UDQS pin of the DRAM These signals are tied at the system planar to either VSS or VDD to configure the serial SPD EEPROM. This is a bidirectional pin used to transfer data into or out of the SPD EEPROM. A resister must be connected to VDD to act as a pull up. This signal is used to clock data into and out of the SPD EEPROM. A resistor may be connected from SCL to VDD to act as a pull up on the system board. Power supply for SPD EEPROM. This supply is separate from the VDD/VDDQ power plane. EEPROM supply is operable from 1.7V to 3.6V. 3 1240pin DDR2 SDRAM Unbuffered DIMMs PIN CONFIGURATION Front Side 1 pin 64 pin 65 pin 121 pin 184 pin 185 pin 120 pin 240 pin Back Side PIN ASSIGNMENT Pin Name Pin Name Pin Name Pin Name Pin Name Pin Name 1 VREF 41 VSS 81 DQ33 121 VSS 161 NC(CB4)* 201 VSS 2 VSS 42 NC(CB0)* 82 VSS 122 DQ4 162 NC(CB5)* 202 DM4 3 DQ0 43 NC(CB1)* 83 DQS4 123 DQ5 163 VSS 203 NC 4 DQ1 44 VSS 84 DQS4 124 VSS 164 NC(DM8)* 204 VSS 5 VSS 45 NC(DQS8)* 85 VSS 125 DM0 165 NC 205 DQ38 6 DQS0 46 NC(DQS8)* 86 DQ34 126 NC 166 VSS 206 DQ39 7 DQS0 47 VSS 87 DQ35 127 VSS 167 NC(CB6)* 207 VSS 8 VSS 48 NC(CB2)* 88 VSS 128 DQ6 168 NC(CB7)* 208 DQ44 9 DQ2 49 NC(CB3)* 89 DQ40 129 DQ7 169 VSS 209 DQ45 10 DQ3 50 VSS 90 DQ41 130 VSS 170 VDDQ 210 VSS 11 VSS 51 VDDQ 91 VSS 131 DQ12 171 CKE1 211 DM5 12 DQ8 52 CKE0 92 DQS5 132 DQ13 172 VDD 212 NC 13 DQ9 53 VDD 93 DQS5 133 VSS 173 A15 213 VSS 14 VSS 54 BA2 94 VSS 134 DM1 174 A14 214 DQ46 15 DQS1 55 NC 95 DQ42 135 NC 175 VDDQ 215 DQ47 16 DQS1 56 VDDQ 96 DQ43 136 VSS 176 A12 216 VSS 17 VSS 57 A11 97 VSS 137 CK1 177 A9 217 DQ52 18 NC 58 A7 98 DQ48 138 CK1 178 VDD 218 DQ53 19 NC 59 VDD 99 DQ49 139 VSS 179 A8 219 VSS 20 VSS 60 A5 100 VSS 140 DQ14 180 A6 220 CK2 21 DQ10 61 A4 101 SA2 141 DQ15 181 VDDQ 221 CK2 22 DQ11 62 VDDQ 102 NC,TEST1 142 VSS 182 A3 222 VSS * The pin names in parenthesises are applied to DIMM with ECC only. Rev. 0.3 / Nov 2006 4 1240pin DDR2 SDRAM Unbuffered DIMMs PIN ASSIGNMENT(Continued) Pin Name Pin Name Pin Name Pin Name Pin Name Pin Name 23 VSS 63 A2 103 VSS 143 DQ20 183 A1 223 DM6 24 DQ16 64 VDD 104 DQS6 144 DQ21 184 VDD 224 NC 25 DQ17 65 VSS 105 DQS6 145 VSS 185 CK0 225 VSS 26 VSS 66 VSS 106 VSS 146 DM2 186 CK0 226 DQ54 27 DQS2 67 VDD 107 DQ50 147 NC 187 VDD 227 DQ55 28 DQS2 68 NC 108 DQ51 148 VSS 188 A0 228 VSS 29 VSS 69 VDD 109 VSS 149 DQ22 189 VDD 229 DQ60 30 DQ18 70 A10/AP 110 DQ56 150 DQ23 190 BA1 230 DQ61 31 DQ19 71 BA0 111 DQ57 151 VSS 191 VDDQ 231 VSS 32 VSS 72 VDDQ 112 VSS 152 DQ28 192 RAS 232 DM7 33 DQ24 73 WE 113 DQS7 153 DQ29 193 S0 233 NC 34 DQ25 74 CAS 114 DQS7 154 VSS 194 VDDQ 234 VSS 35 VSS 75 VDDQ 115 VSS 155 DM3 195 ODT0 235 DQ62 36 DQS3 76 S1 116 DQ58 156 NC 196 A13 236 DQ63 37 DQS3 77 ODT1 117 DQ59 157 VSS 197 VDD 237 VSS 38 VSS 78 VDDQ 118 VSS 158 DQ30 198 VSS 238 VDDSPD 39 DQ26 79 VSS 119 SDA 159 DQ31 199 DQ36 239 SA0 40 DQ27 80 DQ32 120 SCL 160 VSS 200 DQ37 240 SA1 *NC=No connect Note : 1. The TEST pin is reserved for bus analysis tools and is not connected on standard memory module products(DIMMs). 2. NC Pins should not be connected to anything, including bussing within the NC group. Rev. 0.3 / Nov 2006 5 1240pin DDR2 SDRAM Unbuffered DIMMs FUNCTIONAL BLOCK DIAGRAM 512MB(64Mbx64) : HYMP164U64AP6 /S 0 / DQS 0 / LD Q S DQS 0 LD Q S / CS LD M DM 0 DQ 0 DQ 1 DQ 2 DQ 3 DQ 4 DQ 5 DQ 6 DQ 7 I/ O 0 I/ O 1 I/ O 2 I/ O 3 I/ O 4 I/ O 5 I/ O 6 I/ O 7 / DQS 1 DQS 1 D0 / UDQS / DQS 5 UDQS DQS 5 / LDQS / DQS 2 DQS 2 / CS LD M DM 2 D Q 16 D Q 17 D Q 18 D Q 19 D Q 20 D Q 21 D Q 22 D Q 23 I/ O 0 I/ O 1 I/ O 2 I/ O 3 I/ O 4 I/ O 5 I/ O 6 I/ O 7 / DQS 3 DQS 3 D1 VD D S P D LDQS UDQS DQS 7 SDRAMS SDRAMS SDRAMS SDRAMS SDRAMS SDRAMS SDRAMS D0-D 3 D0-D 3 D0-D 3 D0-D 3 D0-D 3 D0-D 3 D0-D 3 S erial P D D O -D 3 V REF D O -D 3 VS S D O -D 3 / CS LD M I/ O 0 I/ O 1 I/ O 2 I/ O 3 I/ O 4 I/ O 5 I/ O 6 I/ O 7 D3 / UDQS UDQS UDM I/ O 8 I/ O 9 I/ O 10 I/ O 11 I/ O 12 I/ O 13 I/ O 14 I/ O 15 DM 7 D Q 56 D Q 57 D Q 58 D Q 59 D Q 60 D Q 61 D Q 62 D Q 63 VD D / V D D Q Rev. 0.3 / Nov 2006 / LDQ S DQS 6 / DQS 7 SCL BA 0- BA 2 A 0 - A 12 / RAS / CAS CKE 0 /WE ODT 0 UDQS UDM I/ O 8 I/ O 9 I/ O 10 I/ O 11 I/ O 12 I/ O 13 I/ O 14 I/ O 15 / DQS 6 / UDQS D2 / UDQS DM 6 D Q 48 D Q 49 D Q 50 D Q 51 D Q 52 D Q 53 D Q 54 D Q 55 UDM I/ O 8 I/ O 9 I/ O 10 I/ O 11 I/ O 12 I/ O 13 I/ O 14 I/ O 15 DM 3 D Q 24 D Q 25 D Q 26 D Q 27 D Q 28 D Q 29 D Q 30 D Q 31 LD M I/ O 0 I/ O 1 I/ O 2 I/ O 3 I/ O 4 I/ O 5 I/ O 6 I/ O 7 DM 5 D Q 40 D Q 41 D Q 42 D Q 43 D Q 44 D Q 45 D Q 46 D Q 47 LDQS / CS LDQS DM 4 D Q 32 D Q 33 D Q 34 D Q 35 D Q 36 D Q 37 D Q 38 D Q 39 UDM I/ O 8 I/ O 9 I/ O 10 I/ O 11 I/ O 12 I/ O 13 I/ O 14 I/ O 15 DM 1 DQ 8 DQ 9 D Q 10 D Q 11 D Q 12 D Q 13 D Q 14 D Q 15 / LDQ S / DQS 4 DQS 4 SCL WP A0 S A0 SDA S erial P D A1 S A1 A1 S A2 C lock S ignal Loads C lock Input SDRAMs C K 0, /C K 0 NC C K 1, /C K 1 2 C K 2, /C K 2 2 N otes: 1. D Q ,D M ,D Q S ,/D Q S resistors : 22 +/- 5 % . 2. B ax,A x,/R A S ,/C A S ,/W E resistors : 10 +/- 5 % . 6 1240pin DDR2 SDRAM Unbuffered DIMMs FUNCTIONAL BLOCK DIAGRAM 1GB(128Mbx64) : HYMP112U64AP8 /S0 /DQS0 DQS0 /DQS4 DQS4 DM0 DM4 DM DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 /CS DM DQS /DQS DQ32 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ39 I/O 0 I/O 1 D0 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 /DQS1 DQS1 /CS I/O 1 D1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 I/O 4 I/O 5 I/O 6 I/O 7 /CS DQS /DQS I/O 0 I/O 1 D5 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 /DQS6 DQS6 DM6 DM /CS DM DQS /DQS DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 I/O 0 I/O 1 D2 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 /DQS3 DQS3 /CS DQS /DQS I/O 0 I/O 1 D6 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 /DQS7 DQS7 DM3 DM7 DM /CS DM DQS /DQS DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ63 I/O 0 I/O 1 I/O 2 D3 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 SCL DQS /DQS I/O 1 I/O 2 D7 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 SDA Serial PD A0 SDRAMS D0-7 SDRAMS D0-7 SDRAMS D0-7 SDRAMS D0-7 SDRAMS D0-7 SDRAMS D0-7 SDRAMS D0-7 /CS I/O 0 Clock Signal Loads SCL WP Rev. 0.3 / Nov 2006 I/O 3 DM DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47 I/O 0 DM2 BA0-BA2 A0-A13 /RAS /CAS CKE0 /WE ODT0 D4 I/O 2 DQS /DQS /DQS2 DQS2 DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 I/O 1 DM5 DM DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 DQS /DQS /DQS5 DQS5 DM1 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 /CS I/O 0 SA0 VDD SPD Serial PD VDD /VDDQ DO-D7 VREF DO-D7 VSS DO-D7 A1 SA1 A1 SA2 Clock Input SDRAMs CK0, /CK0 2 CK1, /CK1 3 CK2, /CK2 3 Notes: 1. DQ,DM,DQS,/DQS resistors : 22 +/- 5 %. 2. Bax,Ax,/RAS,/CAS,/WE resistors : 5.1 +/- 5 %. 7 1240pin DDR2 SDRAM Unbuffered DIMMs FUNCTIONAL BLOCK DIAGRAM 1GB(128Mbx72) - HYMP112U72AP8 /S0 /DQS0 DQS0 /DQS4 DQS4 DM0 DM4 DM DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 /CS DM DQS /DQS DQ32 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ39 I/O 0 I/O 1 D0 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 /DQS1 /DQS5 DQS1 DQS5 DM1 /CS DQS /DQS I/O 0 I/O 1 D4 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM5 DM DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 /CS DM DQS /DQS DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47 I/O 0 I/O 1 D1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 /DQS2 DQS2 /CS DQS /DQS I/O 0 I/O 1 D5 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 /DQS6 DQS6 DM2 DM6 DM DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 /CS DM DQS /DQS DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 I/O 0 I/O 1 D2 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 /DQS3 /DQS7 DQS3 DQS7 DM3 /CS DQS /DQS I/O 0 I/O 1 D6 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM7 DM DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 /CS DM DQS /DQS DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ63 I/O 0 I/O 1 D3 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 /CS DQS /DQS I/O 0 I/O 1 I/O 2 D7 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 /DQS8 DQS8 DM8 Clock Signal Loads DM CB0 CB1 CB2 CB3 CB4 CB5 CB6 CB7 BA0-BA2 A0-A13 /RAS /CAS CKE0 /WE ODT0 /CS DQS /DQS I/O 0 SCL D8 I/O 3 I/O 4 SDA Serial PD WP I/O 1 I/O 2 SCL Clock Input SDRAMs CK0, /CK0 3 A0 A1 A1 CK1, /CK1 3 SA0 SA1 SA2 CK2, /CK2 3 A1 I/O 5 I/O 6 I/O 7 SDRAMS D0-7,D8 SDRAMS D0-7,D8 SDRAMS D0-7,D8 SDRAMS D0-7,D8 SDRAMS D0-7,D8 SDRAMS D0-7,D8 SDRAMS D0-7,D8 Rev. 0.3 / Nov 2006 V DD SPD Serial PD V DD /V DDQ DO-D8 V REF DO-D8 V SS DO-D8 Notes: 1. DQ,DM,DQS,/DQS resistors : 22 +/- 5 %. 2. Bax,Ax,/RAS,/CAS,/WE resistors : 5.1 +/- 5 %. 8 1240pin DDR2 SDRAM Unbuffered DIMMs FUNCTIONAL BLOCK DIAGRAM 2GB(256Mbx64) - HYMP125U64AP8 /S1 /S0 / DQS0 DQS0 / DQS4 DQS4 DM0 DM4 DM DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 /CS DQS /DQS / I/ O 0 I/ O 3 /CS DM DQS /DQS DQ32 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ39 I/ O 0 I/ O 1 I/ O 2 DM I/ O 1 D0 I/ O 2 D8 I/ O 3 I/ O 4 I/ O 4 I/ O 5 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 / DQS1 DQS1 DQS /DQS /CS DM I/ O 0 I/ O 0 I/ O 1 I/ O 1 /CS DQS /DQS I/ O 2 I/ O 2 D4 I/ O 3 D12 I/ O 3 I/ O 4 I/ O 4 I/ O 5 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 / DQS5 DQS5 DM1 DM5 DM DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 /CS I/ O 0 I/ O 3 /CS DQS /DQS DM DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47 I/ O 0 I/ O 1 I/ O 2 DM DQS /DQS I/ O 1 D1 I/ O 2 D9 I/ O 3 I/ O 4 I/ O 4 I/ O 5 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 / DQS2 DQS2 /CS DQS /DQS I/ O 0 DM /CS DQS /DQS I/ O 0 I/ O 1 I/ O 1 I/ O 2 I/ O 2 D5 I/ O 3 D13 I/ O 3 I/ O 4 I/ O 4 I/ O 5 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 / DQS6 DQS6 DM2 DM6 DM DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 /CS DM DQS /DQS I/ O 0 I/ O 0 I/ O 1 I/ O 1 I/ O 2 I/ O 2 I/ O 3 D2 /CS I/ O 4 I/ O 5 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 D10 I/ O 3 I/ O 4 DM DQS /DQS / DQS3 DQS3 / DQS7 DQS7 DM3 DM7 I/ O 0 I/ O 0 I/ O 1 I/ O 1 I/ O 2 I/ O 4 I/ O 5 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 I/ O 1 I/ O 1 I/ O 2 I/ O 2 I/ O 3 D3 I/ O 4 I/ O 4 I/ O 5 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 BA0-BA2 A0-A15 CKE0 CKE1 /CAS /RAS /WE ODT0 ODT1 Rev. 0.3 / Nov 2006 D11 I/ O 3 SDRAMS D0-D15 SDRAMS D0-D15 SDRAMS D0-D7 SDRAMS D8-D15 SDRAMS D0-D15 SDRAMS D0-D15 SDRAMS D0-D15 SDRAMS D0-D7 SDRAMS D8-D15 SCL SCL WP VDD SPD A0 A1 A1 SA0 SA1 SA2 Serial PD VDD /V DDQ DO-D15 V REF DO-D15 VSS DO-D15 DM I/ O 0 I/ O 1 I/ O 1 I/ O 2 I/ O 3 /CS DQS /DQS I/ O 2 D7 D15 I/ O 3 I/ O 4 I/ O 4 SDA Serial PD DQS /DQS I/ O 0 DQS /DQS D14 I/ O 3 I/ O 4 /CS /CS I/ O 2 D6 I/ O 3 DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ63 DM I/ O 0 DM DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 DQS /DQS /CS I/ O 0 I/ O 5 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 Clock Signal Loads Clock Input SDRAMs CK0, /CK0 4 CK1, /CK1 6 CK2, /CK2 6 Notes: 1. DQ,DM,DQS,/DQS resistors : 22 +/- 5 %. 2. Bax,Ax,/RAS,/CAS,/WE resistors : 7.5 +/- 5 %. 9 1240pin DDR2 SDRAM Unbuffered DIMMs FUNCTIONAL BLOCK DIAGRAM 2GB(256Mbx72) - HYMP125U72AP8 /S1 /S0 / DQS0 DQS0 / DQS4 DQS4 DM0 DM4 DM D Q0 D Q1 D Q2 D Q3 D Q4 D Q5 D Q6 DQ7 / CS DM DQ S / DQ S I/ O 0 / CS DQ32 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ 39 I/ O 0 I/ O 1 I/ O 1 I/ O 2 I/ O 2 D0 I/ O 3 D9 I/ O 3 I/ O 4 I/ O 4 I/ O 5 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 DM DQ S / DQ S / DQS1 DQS1 / CS DM DQ S / DQ S / CS DQ S / DQ S I/ O 0 I/ O 0 I/ O 1 I/ O 1 I/ O 2 I/ O 2 D4 I/ O 3 D13 I/ O 3 I/ O 4 I/ O 4 I/ O 5 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 / DQS5 DQS5 DM1 DM5 DM D Q8 D Q9 DQ 10 DQ 11 DQ 12 DQ 13 DQ 14 DQ 15 / CS DM DQ S / DQ S I/ O 0 / CS DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ 47 I/ O 0 I/ O 1 I/ O 1 I/ O 2 I/ O 2 D1 I/ O 3 D10 I/ O 3 I/ O 4 I/ O 4 I/ O 5 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 DM DQ S / DQ S / DQS2 DQS2 / CS DM DQ S / DQ S / CS DQ S / DQ S I/ O 0 I/ O 0 I/ O 1 I/ O 1 I/ O 2 I/ O 2 D5 I/ O 3 D14 I/ O 3 I/ O 4 I/ O 4 I/ O 5 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 / DQ S6 DQ S6 DM2 DM6 / CS DQ 16 DQ 17 DQ 18 DQ 19 DQ 20 DQ 21 DQ 22 DQ 23 DM DQ S / DQ S I/ O 0 / CS DQ 48 DQ 49 DQ 50 DQ 51 DQ 52 DQ 53 DQ 54 DQ 55 I/ O 0 I/ O 1 I/ O 1 I/ O 2 I/ O 2 D2 I/ O 3 D11 I/ O 3 I/ O 4 I/ O 4 I/ O 5 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 DM DQ S / DQ S / DQS3 DQS3 / CS DM DQS / DQS I/ O 0 / CS DQ S / DQ S I/ O 0 I/ O 1 I/ O 1 I/ O 2 I/ O 2 D6 I/ O 3 D15 I/ O 3 I/ O 4 I/ O 4 I/ O 5 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 / DQS7 DQS7 DM3 DM7 DM DQ 24 DQ 25 DQ 26 DQ 27 DQ 28 DQ 29 DQ 30 DQ 31 / CS DM DQ S / DQ S I/ O 0 / CS DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ 63 I/ O 0 I/ O 1 I/ O 1 I/ O 2 I/ O 2 D3 I/ O 3 D12 I/ O 3 I/ O 4 I/ O 4 I/ O 5 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 DM DQ S / DQ S / CS DM DQ S / DQ S I/ O 0 I/ O 0 I/ O 1 I/ O 1 I/ O 2 DQ S / DQ S I/ O 2 D7 I/ O 3 / CS I/ O 3 D 16 I/ O 4 I/ O 4 I/ O 5 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 / DQS8 DQS8 DM8 DM C B0 C B1 C B2 C B3 C B4 C B5 C B6 CB7 / CS DM DQ S / DQ S I/ O 0 I/ O 0 I/ O 1 I/ O 1 I/ O 2 I/ O 3 I/ O 3 I/ O 5 I/ O 6 I/ O 7 I/ O 6 I/ O 7 Rev. 0.3 / Nov 2006 V D D S PD Serial PD V DD /V D DQ DO-D 17 Clock Signal Loads D17 C lock Input SD RAM s CK0, /C K0 6 V REF DO-D 17 CK1, /C K1 6 VSS DO-D 17 CK2, /C K2 6 I/ O 4 I/ O 5 /W E ODT0 ODT1 DQ S / DQ S I/ O 2 D8 I/ O 4 BA0-BA2 A0-A13 CKE0 CKE1 /CAS /RAS / CS SDR AM S D 0-D 17 SDR AM S D0-D 17 SDRAM S D 0-D8 SDR AM S D 9-D 17 SDR AM S D0-D 17 SDR AM S D 0-D 17 SDR AM S D 0-D 17 SD RAM S D0-D8 SDR AM S D9-D 17 S CL SCL WP SDA S erial PD A0 A1 A1 SA0 S A1 SA2 Notes: 1. D Q ,DM ,DQ S,/DQ S resistors : 22 +/- 5 % . 2. Bax,Ax,/R AS,/CAS,/W E resistors : 7.5 +/- 5 % . 10 1240pin DDR2 SDRAM Unbuffered DIMMs ABSOLUTE MAXIMUM RATINGS Parameter Symbol Value Unit Note VDD - 1.0 V ~ 2.3 V V 1 VDDQ - 0.5 V ~ 2.3 V V 1 VIN, VOUT Voltage on VDD pin relative to Vss Voltage on VDDQ pin relative to Vss Voltage on any pin relative to Vss Storage Temperature Storage Humidity(without condensation) - 0.5 V ~ 2.3 V V 1 TSTG -50 ~ +100 oC 1 HSTG 5 to 95 % 1 Note : 1. Stress greater than those listed may cause permanent damage to the device. This is a stress rating only, and device functional operation at or above the conditions indicated is not implied. Expousure to absolute maximum rating con ditions for extended periods may affect reliablility. OPERATING CONDITIONS Parameter DIMM Operating temperature(ambient) DIMM Barometric Pressure(operating & storage) Symbol TOPR Rating 0 ~ +55 Units oC Notes PBAR TCASE 105 to 69 K Pascal 1 0 ~+95 oC 2 DRAM Component Case Temperature Range Note : 1. Up to 9850 ft. 2. If the DRAM case temperature is Above 85oC, the Auto-Refresh command interval has to be reduced to tREFI=3.9us. For Measurement conditions of TCASE, please refer to the JEDEC document JESD51-2. DC OPERATING CONDITIONS (SSTL_1.8) Parameter Symbol Min Max Unit VDD 1.7 1.9 V VDDQ 1.7 1.9 V 1 Input Reference Voltage VREF 0.49 x VDDQ 0.51 x VDDQ V 2 EEPROM Supply Voltage VDDSPD 1.7 3.6 V VTT VREF-0.04 VREF+0.04 V II -2 2 uA IOZ -5 5 uA Power Supply Voltage Termination Voltage Input leakage current; any input 0V VIN VDD; all other balls not under test = 0V) Output leakage current; 0V VOUT VDDQ; DQ and ODT disabled Note 3 Note : 1. VDDQ must be less than or equal to VDD. 2. Peak to peak ac noise on VREF may not exeed +/-2% VREF(dc) 3. VTT of transmitting device must track VREF of receiving device. Rev. 0.3 / Nov 2006 11 1240pin DDR2 SDRAM Unbuffered DIMMs INPUT DC LOGIC LEVEL Parameter Symbol Min Max Unit Input High Voltage VIH(DC) VREF + 0.125 VDDQ + 0.3 V Input Low Voltage VIL(DC) -0.30 VREF - 0.125 V Note INPUT AC LOGIC LEVEL DDR2 400, 533 Parameter DDR2 667, 800 Unit Note Symbol Min Max Min Max AC Input logic High VIH(AC) VREF + 0.250 - VREF + 0.200 - V AC Input logic Low VIL(AC) - VREF - 0.250 - VREF - 0.200 V Value Units Notes 0.5 * VDDQ V 1 AC INPUT TEST CONDITIONS Symbol Condition VREF Input reference voltage VSWING(MAX) Input signal maximum peak to peak swing 1.0 V 1 SLEW Input signal minimum slew rate 1.0 V/ns 2, 3 Note: 1. Input waveform timing is referenced to the input signal crossing through the VREF level applied to the device under test. 2. The input signal minimum slew rate is to be maintained over the range from VREF to VIH(ac) min for rising edges and the range from VREF to VIL(ac) max for falling edges as shown in the below figure. 3. AC timings are referenced with input waveforms switching from VIL(ac) to VIH(ac) on the positive transitions and VIH(ac) to VIL(ac) on the negative transitions. VDDQ VIH(ac) min VIH(dc) min VREF VIL(dc) max VIL(ac) max VSS VSWING(MAX) delta TF Falling Slew = delta TR VREF - VIL(ac) max Rising Slew = delta TF VIH(ac) min - VREF delta TR < Figure : AC Input Test Signal Waveform > Rev. 0.3 / Nov 2006 12 1240pin DDR2 SDRAM Unbuffered DIMMs Differential Input AC logic Level Symbol Parameter VID (ac) ac differential input voltage VIX (ac) ac differential cross point voltage Min. Max. Units Note 0.5 VDDQ + 0.6 V 1 0.5 * VDDQ - 0.175 0.5 * VDDQ + 0.175 V 2 1. VIN(DC) specifies the allowable DC execution of each input of differential pair such as CK, CK, DQS, DQS, LDQS, LDQS, UDQS and UDQS. 2. VID(DC) specifies the input differential voltage |VTR -VCP | required for switching, where VTR is the true input (such as CK, DQS, LDQS or UDQS) level and VCP is the complementary input (such as CK, DQS, LDQS or UDQS) level. The minimum value is equal to VIH(DC) - VIL(DC). VDDQ VTR Crossing point VID VIX or VOX VCP VSSQ < Differential signal levels > Note: 1. VID(AC) specifies the input differential voltage |VTR -VCP | required for switching, where VTR is the true input signal (such as CK, DQS, LDQS or UDQS) and VCP is the complementary input signal (such as CK, DQS, LDQS or UDQS). The minimum value is equal to V IH(AC) - VIL(AC). 2. The typical value of VIX(AC) is expected to be about 0.5 * VDDQ of the transmitting device and VIX(AC) is expected to track variations in VDDQ . VIX(AC) indicates the voltage at whitch differential input signals must cross. DIFFERENTIAL AC OUTPUT PARAMETERS Symbol VOX (ac) Parameter ac differential cross point voltage Min. Max. Units Note 0.5 * VDDQ - 0.125 0.5 * VDDQ + 0.125 V 1 Note: 1. The typical value of VOX(AC) is expected to be about 0.5 * VDDQ of the transmitting device and VOX(AC) is expected to track variations in VDDQ . VOX(AC) indicates the voltage at whitch differential output signals must cross. Rev. 0.3 / Nov 2006 13 1240pin DDR2 SDRAM Unbuffered DIMMs OUTPUT BUFFER LEVELS OUTPUT AC TEST CONDITIONS Symbol VOTR Parameter Output Timing Measurement Reference Level SSTL_18 Units Notes 0.5 * VDDQ V 1 Note: 1. The VDDQ of the device under test is referenced. OUTPUT DC CURRENT DRIVE Symbol Parameter IOH(dc) Output Minimum Source DC Current IOL(dc) Output Minimum Sink DC Current SSTl_18 Units Notes - 13.4 mA 1, 3, 4 13.4 mA 2, 3, 4 Note: 1.VDDQ = 1.7 V; VOUT = 1420 mV. (VOUT - VDDQ)/IOH must be less than 21 ohm for values of VOUT between VDDQ and VDDQ - 280 mV. 2. VDDQ = 1.7 V; VOUT = 280 mV. VOUT/IOL must be less than 21 ohm for values of VOUT between 0 V and 280 mV. 3. The dc value of VREF applied to the receiving device is set to VTT 4. The values of IOH(dc) and IOL(dc) are based on the conditions given in Notes 1 and 2. They are used to test device drive current capability to ensure VIH min plus a noise margin and VIL max minus a noise margin are delivered to an SSTL_18 receiver. The actual current values are derived by shifting the desired driver operating point along a 21 ohm load line to define a convenient driver current for measurement. Rev. 0.3 / Nov 2006 14 1240pin DDR2 SDRAM Unbuffered DIMMs PIN Capacitance (VDD=1.8V,VDDQ=1.8V, TA=25. f=1MHz ) 512MB : HYMP164U64AP6 Pin CK, CK CKE, ODT,CS Address, RAS, CAS, WE DQ, DM, DQS, DQS Symbol Min Max Unit CCK CI1 CI2 CIO 18 57 42 7 22 63 48 9 pF Symbol Min Max Unit CCK CI1 CI2 CIO 22 62 42 6 30 84 64 9 pF Symbol Min Max Unit CCK CI1 CI2 CIO 22 63 43 6 30 85 66 9 pF Symbol Min Max Unit CCK CI1 CI2 CIO 22 64 50 8 35 87 88 13 pF Symbol Min Max Unit CCK CI1 CI2 CIO 23 65 52 9 35 89 92 13 pF pF pF pF 1GB : HYMP112U64AP8 Pin CK, CK CKE, ODT,CS Address, RAS, CAS, WE DQ, DM, DQS, DQS pF pF pF 1GB : HYMP112U72AP8 Pin CK, CK CKE, ODT,CS Address, RAS, CAS, WE DQ, DM, DQS, DQS pF pF pF 2GB : HYMP125U64AP8 Pin CK, CK CKE, ODT,CS Address, RAS, CAS, WE DQ, DM, DQS, DQS pF pF pF 2GB : HYMP125U72AP8 Pin CK, CK CKE, ODT,CS Address, RAS, CAS, WE DQ, DM, DQS, DQS pF pF pF Note : 1. Pins not under test are tied to GND. 2. These value are guaranteed by design and tested on a sample basis only. Rev. 0.3 / Nov 2006 15 1240pin DDR2 SDRAM Unbuffered DIMMs IDD SPECIFICATIONS (TCASE : 0 to 95) 512MB, 64M x 64 U-DIMM : HYMP164U64AP6 Symbol E3(DDR2 400@CL 3) C4(DDR2 533@CL 4) Y5(DDR2 667@CL 5) S5(DDR2 800@CL 5) Unit IDD0 TBD TBD TBD TBD mA IDD1 TBD TBD TBD TBD mA IDD2P TBD TBD TBD TBD mA IDD2Q TBD TBD TBD TBD mA IDD2N TBD TBD TBD TBD mA IDD3P(F) TBD TBD TBD TBD mA IDD3P(S) TBD TBD TBD TBD mA IDD3N TBD TBD TBD TBD mA IDD4R TBD TBD TBD TBD mA IDD4W TBD TBD TBD TBD mA IDD5B TBD TBD TBD TBD mA IDD6 TBD TBD TBD TBD mA IDD7 TBD TBD TBD TBD mA Note 1 Note : 1. IDD6 current values are guaranted up to Tcase of 85 max. Rev. 0.3 / Nov 2006 16 1240pin DDR2 SDRAM Unbuffered DIMMs IDD SPECIFICATIONS (TCASE : 0 to 95) 1GB, 128M x 64 U-DIMM : HYMP112U64AP8 Symbol E3(DDR2 400@CL 3) C4(DDR2 533@CL 4) Y5(DDR2 667@CL 5) S5(DDR2 800@CL 5) Unit IDD0 TBD TBD TBD TBD mA IDD1 TBD TBD TBD TBD mA IDD2P TBD TBD TBD TBD mA IDD2Q TBD TBD TBD TBD mA IDD2N TBD TBD TBD TBD mA IDD3P(F) TBD TBD TBD TBD mA IDD3P(S) TBD TBD TBD TBD mA IDD3N TBD TBD TBD TBD mA IDD4R TBD TBD TBD TBD mA IDD4W TBD TBD TBD TBD mA IDD5B TBD TBD TBD TBD mA IDD6 TBD TBD TBD TBD mA IDD7 TBD TBD TBD TBD mA Note 1 1GB, 128M x 72 ECC U-DIMM : HYMP112U72AP8 Symbol E3(DDR2 400@CL 3) C4(DDR2 533@CL 4) Y5(DDR2 667@CL 5) S5(DDR2 800@CL 5) Unit IDD0 TBD TBD TBD TBD mA IDD1 TBD TBD TBD TBD mA IDD2P TBD TBD TBD TBD mA IDD2Q TBD TBD TBD TBD mA IDD2N TBD TBD TBD TBD mA IDD3P(F) TBD TBD TBD TBD mA IDD3P(S) TBD TBD TBD TBD mA IDD3N TBD TBD TBD TBD mA IDD4R TBD TBD TBD TBD mA IDD4W TBD TBD TBD TBD mA IDD5B TBD TBD TBD TBD mA IDD6 TBD TBD TBD TBD mA IDD7 TBD TBD TBD TBD mA Note 1 Note : 1. IDD6 current values are guaranted up to Tcase of 85 max. Rev. 0.3 / Nov 2006 17 1240pin DDR2 SDRAM Unbuffered DIMMs 2GB, 256M x 64 U - DIMM : HYMP125U64AP8 Symbol E3(DDR2 400@CL 3) C4(DDR2 533@CL 4) Y5(DDR2 667@CL 5) S5(DDR2 800@CL 5) Unit IDD0 TBD TBD TBD TBD mA IDD1 TBD TBD TBD TBD mA IDD2P TBD TBD TBD TBD mA IDD2Q TBD TBD TBD TBD mA IDD2N TBD TBD TBD TBD mA IDD3P(F) TBD TBD TBD TBD mA IDD3P(S) TBD TBD TBD TBD mA IDD3N TBD TBD TBD TBD mA IDD4R TBD TBD TBD TBD mA IDD4W TBD TBD TBD TBD mA IDD5B TBD TBD TBD TBD mA IDD6 TBD TBD TBD TBD mA IDD7 TBD TBD TBD TBD mA Note 1 2GB, 256M x 72 ECC U-DIMM : HYMP125U72AP8 Symbol E3(DDR2 400@CL 3) C4(DDR2 533@CL 4) Y5(DDR2 667@CL 5) S5(DDR2 800@CL 5) Unit IDD0 TBD TBD TBD TBD mA IDD1 TBD TBD TBD TBD mA IDD2P TBD TBD TBD TBD mA IDD2Q TBD TBD TBD TBD mA IDD2N TBD TBD TBD TBD mA IDD3P(F) TBD TBD TBD TBD mA IDD3P(S) TBD TBD TBD TBD mA IDD3N TBD TBD TBD TBD mA IDD4R TBD TBD TBD TBD mA IDD4W TBD TBD TBD TBD mA IDD5B TBD TBD TBD TBD mA IDD6 TBD TBD TBD TBD mA IDD7 TBD TBD TBD TBD mA Note 1 Note : 1. IDD6 current values are guaranted up to Tcase of 85 max. Rev. 0.3 / Nov 2006 18 1240pin DDR2 SDRAM Unbuffered DIMMs IDD MEASUREMENT CONDITIONS Symbol Conditions Units IDD0 Operating one bank active-precharge current; tCK = tCK(IDD), tRC = tRC(IDD), tRAS = tRASmin(IDD);CKE is HIGH, CS is HIGH between valid commands;Address bus inputs are SWITCHING;Data bus inputs are SWITCHING mA IDD1 Operating one bank active-read-precharge curren ; IOUT = 0mA;BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRC = tRC (IDD), tRAS = tRASmin(IDD), tRCD = tRCD(IDD) ; CKE is HIGH, CS is HIGH between valid commands ; Address bus inputs are SWITCHING ; Data pattern is same as IDD4W mA IDD2P Precharge power-down current ; All banks idle ; tCK = tCK(IDD) ; CKE is LOW ; Other control and address bus inputs are STABLE; Data bus inputs are FLOATING mA IDD2Q Precharge quiet standby current;All banks idle; tCK = tCK(IDD);CKE is HIGH, CS is HIGH; Other control and address bus inputs are STABLE; Data bus inputs are FLOATING mA IDD2N Precharge standby current; All banks idle; tCK = tCK(IDD); CKE is HIGH, CS is HIGH; Other control and address bus inputs are SWITCHING; Data bus inputs are SWITCHING mA IDD3P Active power-down current; All banks open; tCK = tCK(IDD); CKE is LOW; Other control and address bus inputs are STABLE; Data bus inputs are FLOATING Fast PDN Exit MRS(12) = 0 mA Slow PDN Exit MRS(12) = 1 mA IDD3N Active standby current; All banks open; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP =tRP(IDD); CKE is HIGH, CS is HIGH between valid commands; Other control and address bus inputs are SWITCHING; Data bus inputs are SWITCHING mA IDD4W Operating burst write current; All banks open, Continuous burst writes; BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP = tRP(IDD); CKE is HIGH, CS is HIGH between valid commands; Address bus inputs are SWITCHING; Data bus inputs are SWITCHING mA IDD4R Operating burst read current; All banks open, Continuous burst reads, IOUT = 0mA; BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP = tRP(IDD); CKE is HIGH, CS is HIGH between valid commands; Address bus inputs are SWITCHING;; Data pattern is same as IDD4W mA IDD5B Burst refresh current; tCK = tCK(IDD); Refresh command at every tRFC(IDD) interval; CKE is HIGH, CS is HIGH between valid commands; Other control and address bus inputs are SWITCHING; Data bus inputs are SWITCHING mA IDD6 Self refresh current; CK and CK at 0V; CKE 0.2V; Other control and address bus inputs are FLOATING; Data bus inputs are FLOATING. IDD6 current values are guaranted up to Tcase of 85 max. mA IDD7 Operating bank interleave read current; All bank interleaving reads, IOUT = 0mA; BL = 4, CL = CL(IDD), AL = tRCD(IDD)-1*tCK(IDD); tCK = tCK(IDD), tRC = tRC(IDD), tRRD = tRRD(IDD), tRCD = 1*tCK(IDD); CKE is HIGH, CS is HIGH between valid commands; Address bus inputs are STABLE during DESELECTs; Data pattern is same as IDD4R; - Refer to the following page for detailed timing conditions Normal Low Power mA Note: 1. IDD specifications are tested after the device is properly initialized 2. Input slew rate is specified by AC Parametric Test Condition 3. IDD parameters are specified with ODT disabled. 4. Data bus consists of DQ, DM, DQS, DQS, RDQS, RDQS, LDQS, LDQS, UDQS, and UDQS. IDD values must be met with all combinations of EMRS bits 10 and 11. 5. Definitions for IDD LOW is defined as Vin VILAC(max) HIGH is defined as Vin VIHAC(min) STABLE is defined as inputs stable at a HIGH or LOW level FLOATING is defined as inputs at VREF = VDDQ/2 SWITCHING is defined as: inputs changing between HIGH and LOW every other clock cycle (once per two clocks) for address and control signals, and inputs changing between HIGH and LOW every other data transfer (once per clock) for DQ signals not including masks or strobes. Rev. 0.3 / Nov 2006 19 1240pin DDR2 SDRAM Unbuffered DIMMs Electrical Characteristics & AC Timings Speed Bins and CL,tRCD,tRP,tRC and tRAS for Corresponding Bin Speed DDR2-800(S5) DDR2-667(Y5) DDR2-533 (C4) DDR2-400 (E3) Unit Bin(CL-tRCD-tRP) 5-5-5 5-5-5 4-4-4 3-3-3 Parameter min min min min CAS Latency 5 5 4 3 ns tRCD 12.5 15 15 15 ns tRP 12.5 15 15 15 ns tRC 57.5 60 60 55 ns tRAS 45 45 45 40 ns AC Timing Parameters by Speed Grade DDR2-400 Parameter DDR2-533 Symbol Unit Note Min Max Min Max Data-Out edge to Clock edge Skew tAC -600 600 -500 500 ps DQS-Out edge to Clock edge Skew tDQSCK -500 500 -500 450 ns Clock High Level Width tCH 0.45 0.55 0.45 0.55 CK Clock Low Level Width tCL 0.45 0.55 0.45 0.55 CK Clock Half Period tHP min (tCL,tCH) - min (tCL,tCH) - ns System Clock Cycle Time tCK 5000 8000 3750 8000 ps DQ and DM input setup time tDS 150 - 100 - ps 1 DQ and DM input hold time tDH 275 - 225 - ps 1 Control & Address input Pulse Width for each input tIPW 0.6 - 0.6 - tCK tDIPW 0.35 - 0.35 - tCK tHZ - tAC max - tAC max ps tLZ(DQS) tAC min tAC max tAC min tAC max ps DQ low-impedance time from CK/CK tLZ(DQ) 2*tAC min tAC max 2*tAC min tAC max ps DQS-DQ skew for DQS and associated DQ signals tDQSQ - 350 - 300 ps tQHS - 450 - 400 ps tQH tHP - tQHS - tHP - tQHS - ps Write command to first DQS latching transition tDQSS WL - 0.25 WL + 0.25 WL - 0.25 WL + 0.25 tCK DQS input high pulse width tDQSH 0.35 - 0.35 - tCK DQS input low pulse width DQ and DM input pulse witdth for each input pulse width for each input Data-out high-impedance window from CK, /CK DQS low-impedance time from CK/CK DQ hold skew factor DQ/DQS output hold time from DQS tDQSL 0.35 - 0.35 - tCK DQS falling edge to CK setup time tDSS 0.2 - 0.2 - tCK DQS falling edge hold time from CK tDSH 0.2 - 0.2 - tCK Mode register set command cycle time tMRD 2 - 2 - tCK Write postamble tWPST 0.4 0.6 0.4 0.6 tCK Write preamble tWPRE 0.35 - 0.35 - tCK Rev. 0.3 / Nov 2006 20 1240pin DDR2 SDRAM Unbuffered DIMMs - continued DDR2-400 Parameter DDR2-533 Symbol Unit Note Min Max Min Max Address and control input setup time tIS 350 - 250 - Address and control input hold time tIH 475 - 375 - ps Read preamble tRPRE 0.9 1.1 0.9 1.1 tCK Read postamble tRPST 0.4 0.6 0.4 0.6 tCK Auto-Refresh to Active/Auto-Refresh command period tRFC 127.5 - 127.5 - ns Row Active to Row Active Delay for 1KB page size tRRD 7.5 - 7.5 - ns Row Active to Row Active Delay for 2KB page size tRRD 10 - 10 - ns Four Activate Window for 1KB page size tFAW 37.5 - 37.5 - ns Four Activate Window for 2KB page size tFAW 50 - 50 - ns CAS to CAS command delay tCCD 2 Write recovery time tWR 15 - 15 - ns Auto Precharge Write Recovery + Precharge Time tDAL tWR+tRP - tWR+tRP - tCK Write to Read Command Delay tWTR 10 - 7.5 - ns Internal read to precharge command delay tRTP 7.5 Exit self refresh to a non-read command tXSNR tRFC + 10 Exit self refresh to a read command tXSRD 200 - 200 - tCK - 2 - tCK Exit precharge power down to any non-read command 2 ps tCK 7.5 ns tRFC + 10 ns tXP 2 Exit active power down to read command tXARD 2 2 tCK Exit active power down to read command (Slow exit, Lower power) tXARDS 6 - AL 6 - AL tCK CKE 3 3 tCK AOND 2 tAON CKE minimum pulse width (high and low pulse width) t t ODT turn-on delay 2 2 tAC(min) tAC(max)+1 tAONPD tAC(min)+2 2tCK+tAC(m ax)+1 tAOFD 2.5 2.5 AOF tAC(min) tAC(max)+ 0.6 AOFPD tAC(min)+2 2.5tCK+tA C(max)+1 ODT to power down entry latency tANPD 3 3 tCK ODT power down exit latency tAXPD 8 8 tCK OCD drive mode output delay tOIT 0 tDelay tIS+tCK+tIH tREFI - 7.8 - 7.8 us 2 tREFI - 3.9 - 3.9 us 3 ODT turn-on ODT turn-on(Power-Down mode) ODT turn-off delay t ODT turn-off ODT turn-off (Power-Down mode) Minimum time clocks remains ON after CKE asynchronously drops LOW t Average periodic Refresh Interval 12 2 tCK tAC(min) tAC(max)+1 ns tAC(min)+2 2tCK+tAC(m ax)+1 ns 2.5 2.5 tCK tAC(min) tAC(max)+ 0.6 ns tAC(min)+2 2.5tCK+tA C(max)+1 ns 0 12 tIS+tCK+tIH ns ns Note : 1. For details and notes, please refer to the relevant HYNIX component datasheet (HY5PS1G(8, 16)31AFP). 2. 0C TCASE 85C 3. 85C TCASE 95C Rev. 0.3 / Nov 2006 21 1240pin DDR2 SDRAM Unbuffered DIMMs Parameter Symbol DDR2-667 DDR2-800 min max min max Unit Note DQ output access time from CK/CK tAC -450 +450 -400 +400 DQS output access time from CK/CK tDQSCK -400 +400 -350 +350 ps CK high-level width tCH 0.45 0.55 0.45 0.55 tCK CK low-level width tCL 0.45 0.55 0.45 0.55 tCK CK half period tHP min(tCL, tCH) - min(tCL, tCH) - ps Clock cycle time, CL=x tCK 3000 8000 2500 tDS 100 - 50 - ps 1 tDH 175 - 125 - ps 1 Control & Address input pulse width for each input tIPW 0.6 - 0.6 - tCK DQ and DM input pulse width for each input tDIPW 0.35 - 0.35 - tCK Data-out high-impedance time from CK/CK tHZ - tAC max - tAC max ps DQS low-impedance time from CK/CK tLZ(DQS) tAC min tAC max tAC min tAC max ps DQ low-impedance time from CK/CK tLZ(DQ) 2*tAC min tAC max 2*tAC min tAC max ps DQS-DQ skew for DQS and associated DQ signals tDQSQ - 240 - 200 ps DQ hold skew factor tQHS - 340 - 300 ps DQ/DQS output hold time from DQS tQH tHP - tQHS - tHP - tQHS - ps First DQS latching transition to associated clock edge tDQSS - 0.25 + 0.25 - 0.25 + 0.25 tCK DQS input high pulse width tDQSH 0.35 - 0.35 - tCK DQS input low pulse width tDQSL 0.35 - 0.35 - tCK DQS falling edge to CK setup time tDSS 0.2 - 0.2 - tCK DQS falling edge hold time from CK tDSH 0.2 - 0.2 - tCK Mode register set command cycle time tMRD 2 - 2 - tCK Write postamble tWPST 0.4 0.6 0.4 0.6 tCK Write preamble tWPRE 0.35 - 0.35 - tCK Address and control input setup time tIS 200 - 175 - ps Address and control input hold time tIH 275 - 250 - ps Read preamble tRPRE 0.9 1.1 0.9 1.1 tCK Read postamble tRPST 0.4 0.6 0.4 0.6 tCK Auto-Refresh to Active/Auto-Refresh command period tRFC 127.5 - 127.5 - ns Active to active command period for 1KB page size products tRRD 7.5 - 7.5 - ns Active to active command period for 2KB page size products tRRD 10 - 10 - ns Four Active Window for 1KB page size products tFAW 37.5 - 35 - ns Four Active Window for 2KB page size products tFAW 50 - 45 - ns DQ and DM input setup time (differential strobe) DQ and DM input hold time (differential strobe) Rev. 0.3 / Nov 2006 ps ps 22 1240pin DDR2 SDRAM Unbuffered DIMMs - continued Symbol Parameter DDR2-667 min DDR2-800 max min max 2 Unit Note CAS to CAS command delay tCCD 2 Write recovery time tWR 15 - 15 - tCK ns Auto precharge write recovery + precharge time tDAL WR+tRP - WR+tRP - tCK Internal write to read command delay tWTR 7.5 - 7.5 - ns Internal read to precharge command delay tRTP 7.5 7.5 ns tRFC + 10 ns Exit self refresh to a non-read command tXSNR tRFC + 10 Exit self refresh to a read command tXSRD 200 - 200 - tCK Exit precharge power down to any non-read command tXP 2 - 2 - tCK Exit active power down to read command tXARD 2 2 tCK tXARDS 7 - AL 8 - AL tCK tCKE 3 3 tCK ODT turn-on delay t 2 2 2 2 tCK ODT turn-on tAON tAC(min) tAC(max) +0.7 tAC(min) tAC(max) +0.7 ns ODT turn-on(Power-Down mode) tAONPD ODT turn-off delay t Exit active power down to read command (Slow exit, Lower power) CKE minimum pulse width (high and low pulse width) AOND AOFD tAC(min)+2 2tCK+ tAC(min) 2tCK+ tAC(max)+1 +2 tAC(max)+1 2.5 2.5 tAC(min) tAC(max)+ 0.6 2.5 2.5 tCK tAC(min) tAC(max) +0.6 ns tAC(min) +2 2.5tCK+ tAC(min) 2.5tCK+ tAC(max)+1 +2 tAC(max)+1 ns tCK ODT turn-off t ODT turn-off (Power-Down mode) tAOFPD ODT to power down entry latency tANPD 3 3 ODT power down exit latency tAXPD 8 8 OCD drive mode output delay tOIT 0 Minimum time clocks remains ON after CKE asynchronously drops LOW Average periodic Refresh Interval AOF tDelay ns 12 tIS+tCK+tI H 0 tCK 12 tIS+tCK +tIH ns ns tREFI - 7.8 - 7.8 us 2 tREFI - 3.9 - 3.9 us 3 Note : 1. For details and notes, please refer to the relevant HYNIX component datasheet (HY5PS1G(8,16)31AFP). 2. 0C TCASE 85C 3. 85C TCASE 95C Rev. 0.3 / Nov 2006 23 1240pin DDR2 SDRAM Unbuffered DIMMs PACKAGE OUTLINE 64Mx 64 - HYMP164U64AP6 Front Side 133.35 2.7 max (Front) 4.00.1 30.0 Detail-A Detail-B 5.175 5.175 63.0 5.0 1.270.10 55.0 10.0 17.80 Back 3.0 3.0 Detail of Contacts B 2.50 1.0 3.80 2.50 0.20 0.20 Detail of Contacts A 0.8 0.05 1.50 0.10 5.00 Note) All dimensions are typical millimeter scale unless otherwise stated. Rev. 0.3 / Nov 2006 24 1240pin DDR2 SDRAM Unbuffered DIMMs PACKAGE OUTLINE 128Mx 64 - HYMP112U64AP8 Front Side 133.35 2. 7 max (Front) 4.00.1 30.0 Detail-A Detail-B 5.175 5.175 63.0 5.0 1. 27 0.10 55.0 10.0 17.80 Back 3.0 3.0 Detail of Contacts B 2.50 1.0 3.80 2.50 0.20 0.20 Detail of Contacts A 0.8 0.05 1.50 0.10 5.00 Note) All dimensions are typical millimeter scale unless otherwise stated. Rev. 0.3 / Nov 2006 25 1240pin DDR2 SDRAM Unbuffered DIMMs PACKAGE OUTLINE 128Mx 72 - HYMP112U72AP8 Front Side 133.35 2. 7 max (Front) 4.00.1 30.0 Detail-A Detail-B 5.175 5.175 63.0 5.0 1. 27 0.10 55.0 10.0 17.80 Back 3.0 3.0 Detail of Contacts B 2.50 1.0 3.80 2.50 0.20 0.20 Detail of Contacts A 0.8 0.05 1.50 0.10 5.00 Note) All dimensions are typical millimeter scale unless otherwise stated. Rev. 0.3 / Nov 2006 26 1240pin DDR2 SDRAM Unbuffered DIMMs PACKAGE OUTLINE 256Mx 64 - HYMP125U64AP8 Front Side 133.35 4.00 max. 4.00.1 30.0 Detail-A Detail-B 5.175 5.175 63.0 5.0 1.27 0.10 55.0 10.0 17.80 Back 3.0 3.0 Detail of Contacts B 2.50 1.0 3.80 2.50 0.20 0.20 Detail of Contacts A 0.8 0.05 1.50 0.10 5.00 Note) All dimensions are typical millimeter scale unless otherwise stated. Rev. 0.3 / Nov 2006 27 1240pin DDR2 SDRAM Unbuffered DIMMs PACKAGE OUTLINE 256Mx 72 - HYMP125U72AP8 Front Side 133.35 4.00 max. 4.00.1 30.0 Detail-A Detail-B 5.175 5.175 63.0 5.0 1.27 0.10 55.0 10.0 17.80 Back 3.0 3.0 Detail of Contacts B 2.50 1.0 3.80 2.50 0.20 0.20 Detail of Contacts A 0.8 0.05 1.50 0.10 5.00 Note) All dimensions are typical millimeter scale unless otherwise stated. Rev. 0.3 / Nov 2006 28 1240pin DDR2 SDRAM Unbuffered DIMMs REVISION HISTORY Revision History Date 0.1 Initial data sheet released Mar. 2006 0.2 Leakage current spec. added to the DC OPERATING CONDITIONS Jul. 2006 0.3 Corrected Type errors Nov. 2006 Rev. 0.3 / Nov 2006 Remark 29