LRTB G6SG
2013-03-13 22
Fußnoten:
1)
Helligkeitswerte werden während eines Strompulses
einer typischen Dauer von 25 ms, mit einer internen
Reproduzierbarkeit von +/- 8 % und einer erweiterten
Messunsicherheit von +/- 11 % gemessen (gemäß
GUM mit Erweiterungsfaktor k = 3).
2)
Die LED kann kurzzeitig in Sperrichtung betrieben
werden.
3)
R
thJA
ergibt sich bei Montage auf PC-Board FR 4
(Padgröße ≥16 mm
2
je Pad)
4)
Die dominante Wellenlänge wird während eines
Strompulses einer typischen Dauer von 25 ms, mit einer
internen Reproduzierbarkeit von +/- 0,5 nm und einer
erweiterten Messunsicherheit von +/- 1 nm gemessen
(gemäß GUM mit Erweiterungsfaktor k = 3).
5)
Vorwärtsspannungen werden während eines
Strompulses einer typischen Dauer von 8 ms, mit einer
internen Reproduzierbarkeit von +/- 0,05 V und einer
erweiterten Messunsicherheit von +/- 0,1 V gemessen
(gemäß GUM mit Erweiterungsfaktor k=3).
6)
Wegen der besonderen Prozessbedingungen bei der
Herstellung von LED können typische oder abgeleitete
technische Parameter nur aufgrund statistischer Werte
wiedergegeben werden. Diese stimmen nicht
notwendigerweise mit den Werten jedes einzelnen
Produktes überein, dessen Werte sich von typischen
und abgeleiteten Werten oder typischen Kennlinien
unterscheiden können. Falls erforderlich, z.B. aufgrund
technischer Verbesserungen, werden diese typischen
Werte ohne weitere Ankündigung geändert.
7)
Im gestrichelten Bereich der Kennlinien muss mit
erhöhten Helligkeitsunterschieden zwischen
Leuchtdioden innerhalb einer Verpackungseinheit
gerechnet werden.
Dimmverhältnis im Gleichstrom-Betrieb max. 5:1 für red
8)
Maße werden wie folgt angegeben: mm (inch)
9)
Gehäuse hält TTW-Löthitze aus nach CECC 00802
10)
Ein kritisches Bauteil ist ein Bauteil, das in
lebenserhaltenden Apparaten oder Systemen
eingesetzt wird und dessen Defekt voraussichtlich zu
einer Fehlfunktion dieses lebenserhaltenden Apparates
oder Systems führen wird oder die Sicherheit oder
Effektivität dieses Apparates oder Systems
beeinträchtigt.
11)
Lebenserhaltende Apparate oder Systeme sind für
(a) die Implantierung in den menschlichen Körper
oder
(b) für die Lebenserhaltung bestimmt.
Falls sie versagen, kann davon ausgegangen werden,
dass die Gesundheit und das Leben des Patienten in
Gefahr ist.
Published by
OSRAM Opto Semiconductors GmbH
Leibnizstrasse 4, D-93055 Regensburg
www.osram-os.com
© All Rights Reserved.
Remarks:
1)
Brightness values are measured during a current pulse
of typical 25 ms, with an internal reproducibility of +/- 8
% and an expanded uncertainty of +/- 11 % (acc. to
GUM with a coverage factor of k = 3).
2)
Driving the LED in reverse direction is suitable for short
term application.
3)
R
thJA
results from mounting on PC board FR 4
(pad size ≥16 mm
2
per pad)
4)
The dominant wavelength is measured at a current
pulse of typical 25 ms, with an internal reproducibility of
+/- 0,5 nm and an expanded uncertainty of +/- 1 nm
(acc. to GUM with a coverage factor of k=3).
5)
The forward voltage is measured during a current pulse
of typical 8 ms, with an internal reproducibility of +/- 0,05
V and an expanded uncertainty of +/- 0,1 V (acc. to
GUM with a coverage factor of k=3).
6)
Due to the special conditions of the manufacturing
processes of LED, the typical data or calculated
correlations of technical parameters can only reflect
statistical figures. These do not necessarily correspond
to the actual parameters of each single product, which
could differ from the typical data and calculated
correlations or the typical characteristic line. If
requested, e.g. because of technical improvements,
these typ. data will be changed without any further
notice.
7)
In the range where the line of the graph is broken, you
must expect higher brightness differences between
single LEDs within one packing unit.
Dimming range for direct current mode max. 5:1 for red
8)
Dimensions are specified as follows: mm (inch)
9)
Package able to withstand TTW-soldering heat acc. to
CECC 00802
10)
A critical component is a component used in a
life-support device or system whose failure can
reasonably be expected to cause the failure of that
life-support device or system, or to affect its safety or the
effectiveness of that device or system.
11)
Life support devices or systems are intended
(a) to be implanted in the human body,
or
(b) to support and/or maintain and sustain human life. If
they fail, it is reasonable to assume that the health and
the life of the user may be endangered.