COUNT/RATE COUNT/RATE CP4-92 SERIES UP/DOWN COUNTER, BATCH COUNTER CHRONOMETER AND RATE CONTROLLER * Backlit Green LCD or Red Illuminated Display * Displays Actual and Preset Count C UL * 1/16 DIN-Sized (48 x 48mm) Housing (R) US LISTED The CP4-92 Series is a programmable dual preset up/down counter, batch counter, chronometer and rate controller with relay outputs. The CP4-92 display shows both actual and preset values. Both count and preset values are saved in EEPROM memory. The unit provides a built-in sensor power supply of 12 VDC, 100mA and will accept contact or solid state inputs. CONFORMITY: SPECIFICATIONS: RF Emissions (EMC) CENELEC EN 55022; Class A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 to 260 VAC 20 to 55 VAC Vibration limits (in 3 axes) 10 to 30 VDC IEC 68-2-6; 10-55Hz/.0375mm 12VDC 100mA 5 digit, Green backlit LCD 5 digit, Red Illuminated -9999 to +99999 WIRING: Power supply 8mm - actual 4mm preset 2 2 Inputs, IN1, IN2 Contact Closure, DC Voltage, NPN/PNP transistor Low Level: 0 to 1 VDC High Level: 4 to 30 VDC Impedance: 10 K Low Speed: 30 Hz Max. NPN High Speed: 5 kHz + Up IN1 - Count input DN IN1 - Count input PNP IND IN1 - one direction IN2 - opposite direction DIR IN1 - Count input IN2 - Change in direction input CUMUL IN1 - Input DIMENSIONS: inches (mm) IN2 - Same direction input Phase; Quadrature Up/Down Mode Phase x 2, Phase x 4 Dry contact, voltage, solid state: NPN/PNP front panel Programmable from 0.001 to 99.999 2 x 2 Amp SP N.O. Relay Repeat or single cycle (11) (48) .44" Maintained or pulsed output of 500ms. 1.90" 2 Screw terminals: 2 x 1.5mm NEMA 12, IP54 Panel cut-out 3 3 3 3 OUT : 2A/250V ~ 1 2 OUT1 OUT2 3 4 5 6 7 8 9 10 11 12 IN1 IN2 RST 0V+12V 100mA 1.90" (48) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level Level Level Level P +.024 0 ORDERING INFORMATION: Part Number 87 618 228 87 618 224 87 618 222 Input Voltage 80 to 260 VAC 20 to 55 VAC 10 to 30 VDC Display Backlit Green Backlit Green Backlit Green 87 618 328 87 618 324 87 618 322 80 to 260 VAC 20 to 55 VAC 10 to 30 VDC Red Illuminated Red Illuminated Red Illuminated RST (114) 4.51" (45 +0.6 0 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.78" Input Power . . . . . . ................ ................ Sensor Supply . . . . Display . . . . . . . . . . ................ ................ Display digit height ................ Presets . . . . . . . . . . Count Inputs . . . . . . ................ ................ ................ ................ ................ ................ Input Modes . . . . . . ................ ................ ................ ................ ................ ................ ................ ................ ................ Reset Input . . . . . . . Scale factor . . . . . . Output . . . . . . . . . . . Output Modes . . . . . ................ Connections . . . . . . Front Panel Rating . Immunity to interference and noise (EMC) IEC 1000.4.2 IEC 1000.4.3 Radiated disturbance IEC 1000.4.4 Fast transient IEC 255.4 1.78" +.024 0 (45 +0.6 0 ) IN STOCK Products and specifications subject to change without notice. Consult factory for application assistance. 204 Airline Drive, Suite 300, Coppell, Texas 75019 / Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 7-13 7 COUNT/RATE COUNT/RATE Batch counter function Batch counter function Principle P1 is the "batch" preset. Example On a packing line, bottles need to be counted into packs of 6 bottles and then dispatched in a box containing a batch of 4 packs. When P2 is displayed, the value displayed on the upper digits represents the current counter value (reset to P2). In this configuration the "RST" key on the front panel reinitializes the current value. When P1 (batch preset) is displayed, the value displayed on the upper digits represents the value of the Batch counter. P2: current counter preset value: 00006 P1: batch counter preset value: 00004 In this configuration the "RST" key on the front panel resets the batch counter. Current counter 012345 012345 012345 012345 012345 012345 0 1 OUT 2 Batch counter An "electrical" reset (RST terminal) still resets the current counter value and that of the batch counter. 2 3 0 1 OUT 1 Reset Tachometer function Measurement principle Measurement begins on a rising edge of the signal to be measured. The measurement time is greater than TR, but less than TL. Measurement stops at the end of the current period (3), after TR. If the period (3) does not end before TL, the measurement result will be zero (0). 3 1 2 Signal measurement period Time TR Time TL Start of measurement The outputs are updated each time measurement ends according to the selected output mode. - Maintained output: output active if the measured speed is greater than the preset speed. - Pulsed output: output activated during time T, when the preset threshold is crossed. Speed P2 P2 P1 P1 t 0 Out 1 (1) Out 2 (2) t 0 Out 1 Out 2 Out 1 (2) Out 2 (1) Maintained output End of measurement Measurement precision: 100 + (200 / TR) PPM Example: for TR = 1s 300 PPM (0.03%) Speed (1) Signal to be measured Out 1 Out 2 (2) Pulsed output Chronometer function (Precision: 150 ppm) 1 - Input IN1 2 - Display (0 PR), 1-channel pulse measurement 3 - Display (PR 0), 1-channel pulse measurement 1 1 - Input IN1 2 - Display (0 PR), 1-channel pulse measurement 3 - Display (PR 0), 1-channel pulse measurement 1 1 - Input IN1 (start counting) 2 - Input IN2 (stop counting) 3 - Display (0 PR), measurement on 2 separate channels 4 - Display (PR 0), measurement on 2 separate channels 1 Accessory T1 2 0 --- 3 Tn --- T2 T1 ---------- T1+T2 Tn-T1 ---------- Tn-(T1+T2) T1 T2 2 0 ---------- T1 ---------- T1+T2 3 Tn ---------- Tn-T1 ---------- Tn-(T1+T2) T1 T2 ---------- T1+T2 Tn-T1 ---------- Tn-(T1+T2) 2 3 4 0 T1 ---------- Tn ---------- Adaptor frame: 79 237 807 o 49 x 50.5 mm Products and specifications subject to change without notice. Consult factory for application assistance. 204 Airline Drive, Suite 300, Coppell, Texas 75019 / Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 7-14