3793-60,2,3,5,60T02TC - 3M - Product.Network

Electronic Solutions Division

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ Four-Wall Header

.100” × .100” Latch/Ejector, Straight, Compliant Pin 3000 Series

Military (with 3M’s 3518 and N3518 polarizing key) •

and centerbump polarization

Optional ejector latches•

Optional polarizing posts•

Mounting holes for securing header to board•

Dependable eye-of-the needle pin design•

Optional high-temperature insulator•

See Regulatory Information Appendix (RIA) for •

chemical compliance information

Date Modied: April 30, 2008 TS-0478-B

Sheet 1 of 3

Physical

Insulation:

Material: Glass Filled Polyester (PBT) Glass Filled Polyester (PCT)

Flammability: UL 94V-0

Color: Gray (PBT), Black (PCT)

Contact:

Material: Copper Alloy

Plating:

Underplating: 100 μ” [ 2.54 μm ] Nickel

Wiping Area: 30 μ” [ 0.76 μm ] Gold

Solder Tails: 100 μ” [ 2.54 μm ] Tin Lead or 300u” [7.62 um] Matte Tin (See Ordering Information)

Marking: 3M Logo, Part Identiﬁcation Number and Orientation Triangle

Electrical

Current Rating: 1 A

Insulation Resistance: >1 × 109 Ω at 500 VDC

Withstanding Voltage: 1,000 VRMS at Sea Level

Environmental

Temperature Rating: -55°C to +105°C

UL File No.: E68080

Electronic Solutions Division

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ Four-Wall Header

.100” × .100” Latch/Ejector, Straight, Compliant Pin 3000 Series

TS-0478-B

Sheet 2 of 3

.100

2.54 REF.

.25

6.4

.34

8.6

.28

7.1

.100

2.54 REF.

POSITION #1

.020

0.51

.13

3.2

2X O .100 [2.54]

SEE NOTE #2

.185

4.70

-620T02

Header

with Short Ejector/Latch

for 3M Sockets without Strain Relief

-600T02

Header

with No Ejector/Latch

-630T02

Header

with Long Ejector/Latch

for 3M sockets with Strain Relief

.08

[2.0]

.08

[2.0]

.97 Ref

[24.6]

.573 ± .010

[14.55]

.424 ± .010

[10.77]

1.07 Ref

[27.2]

.37 Ref

[9.4] .46 Ref

[11.7]

Notch A

(See Table & Note 1)

Notch C

(See Table & Note 1)

Notch B

(See Table)

.35

[8.9]

.21

[5.3] .16

[4.1]

.020

[0.51]

.68

[17.3]

.24

[6.1]

.30

[7.6] .19

[4.8]

.025 ± .002 Sq Typ

[0.64]

.175 ± .010

[4.44]

Position 1

Orientation

Triangle

Section A-A

.68

[17.3]

Inch

(mm)

± .005

± .1 ± .01

Tolerance Unless Noted

.0 .00 .000

Inch

[ ] Dimensions for

Reference only

Notes:

1. Notches A & C will accomodate 3M Polarizing Keys 3518 or N3518.

2. Accepts Rear and Front entry mounting hardware:

Rear Entry: #4-24 thread cutting screw

3M Part # 3341-5 (.116 [2.95] dia. mounting hole).

Front Entry (Prior to installation of latch): #2-56 Bolt and Nut

3M Part # 3341-6 (.106 [2.69] dia. mounting hole).

Electronic Solutions Division

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ Four-Wall Header

.100” × .100” Latch/Ejector, Straight, Compliant Pin 3000 Series

TS-0478-B

Sheet 3 of 3

Pin Qty 3M Part

Number

Dimensions Polarizing

Notches

Provided

Insertion platen

3442-00XX

A B C D

10 3793 1.26 (32.1) 1.105 (28.07) 0.865 (21.97) 0.71 (18.0) BC 3442-0048

14 3314 1.46 (37.2) 1.305 (33.15) 1.065 (27.05) 0.91 (23.1) BC 3442-0049

16 3408 1.56 (39.7) 1.405 (35.69) 1.165 (29.59) 1.01 (25.6) ABC 3442-0050

20 3428 1.76 (44.8) 1.605 (40.77) 1.365 (34.67) 1.21 (30.7) ABC 3442-0051

24 3627 1.96 (49.9) 1.805 (45.85) 1.565 (39.75) 1.41 (35.8) ABC 3442-0052

26 3429 2.06 (52.4) 1.905 (48.39) 1.665 (42.29) 1.51 (38.3) ABC 3442-0053

30 3440 2.26 (57.5) 2.105 (53.47) 1.865 (47.37) 1.71 (43.4) ABC 3442-0054

34 3431 2.46 (62.6) 2.305 (58.55) 2.065 (52.45) 1.91 (48.5) ABC 3442-0055

40 3432 2.76 (70.2) 2.605 (66.17) 2.365 (60.07) 2.21 (56.1) ABC 3442-0056

50 3433 3.26 (82.9) 3.105 (78.87) 2.865 (72.77) 2.71 (68.8) ABC 3442-0057

60 3372 3.76 (95.6) 3.605 (91.57) 3.365 (85.47) 3.21 (81.5) ABC 3442-0058

64 3764 3.96 (100.7) 3.805 (96.65) 3.565 (90.55) 3.41 (86.6) ABC 3442-0059

Ordering Information

Note:

3. Listed below are the PCB hole sizes and tolerances recommended for use with 3M’s compliant

pin header. The insertion force is designed not to exceed 40 pounds per pin and the withdrawal

force is not less than 10 pounds per pin.

4. Use of snap-in latch/ejectors in either short (N3XXX-650T02XX) or long (N3XXX-660T02XX)

styles, installed or shipped separately. (-5 & -6 snap-in latches are dimensionally and functionally

equivalent to -2 & -3 roll pin latches)

Plating sufx:

TC = 30 μ” Gold w/Tin-Lead Tails (App. E2 & C2 Apply)

RB = 30 μ” Gold w/Matte Tin Tails (App. E1 & C1 Apply)

Prex:

Blank = Std.Temp Gray (PBT): (TC Plating Req’d)

N = High Temp Black (PCT) (RB Plating Req’d)

3M Part Number Latch/Ejector System:

0 = No latch/ejectors

2 = Short latch/ejectors

3 = Long latch/ejectors

5 = Short, Snap-In Latch/Ejectors

6 = Long, Snap-In Latch/Ejectors

X XXXX - 6X0T02XX

.106

[2.69] or

.116

[2.95]

(See Note 2)

See Note 3

.300 Min

[7.62]

Side to Side

Stackability

4X .002 ± .001

[0.05]

Break Edges

.100 ± .003

[2.54]

.060

[1.52]

4X R .009 Max

[0.23]

R .020 Sym

[0.51]

.100 ± .003

[2.54]

.352

[8.94]

Position 1

Section R-R

Recommended Mounting Hole Pattern

Section S-S

Section T-T

RST

Tail

Section

Compliant SectionMating

Area

Pin Cross Sections

Hole Size for:

Preferred Drilled - ø.0453 ± .0005

Acceptable Drilled - ø.0453 +.0005

-.0010

After Etchback - ø.0460 Max

After Plating - .ø040 ± .003

Board thickness - .093 to .150

Plating:

.001 Minimum Copper plating thickness

.0003 Min Tin plating

If ordering Snap-In style latches separately, please use the chart below

Short Latch Long Latch Color

High Temp (PPA) 3505-30 3505-31 Gray

High Temp (PPA) N3505-30B N3505-31B Black

Assembly Equipment: Use 3442-00XX platen (see chart above) and

appropriate commercial arbor press to press header into pc board.

Regulatory Information Appendix

3M Electronic Solutions Division/Interconnect

EUROPE

Appendix E1: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC.

This product is RoHS Compliant 2005/95/EC.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of

the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless

the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information

represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and

Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E2: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC.

This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is

compliant by exemption under EU Commission Decision 2005/747/EC.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of

the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless

the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information

represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and

Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E3: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as

amended by Commission Decision 2005/618/EC.

This product contains lead in the solder tail area in excess of the maximum concentration value allowed.

Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information

provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and

Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E4: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC.

This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is

compliant by exemption under EU Commission Decision 2005/717/EC.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of

the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless

the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information

represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and

Buyer’s exclusive remedy will be in accordance with the Warranty stated below.product Warranty stated below.

RIA-2217A-D

Appendix E5: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC.

This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under

Item 6 of the Annex to the Directive.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of

the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless

the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information

represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and

Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

CHINA

Appendix C1: China RoHS

Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for

Certain Hazardous Substances in Electronic Information Products.

This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means

that the product or part does not contain any of the following substances in excess of the following maximum concentration

values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls

or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this

information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and

Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix C2: China RoHS

Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for

Certain Hazardous Substances in Electronic Information Products.

This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that

the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration

values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls

or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this

information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an

extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with

3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the

product Warranty stated below.

RIA-2217A-D

Important Notice

All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness

is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated

with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order

shall have no force or effect unless expressly agreed upon, in writing, by an authorized ofﬁcer of 3M.

Warranty; Limited Remedy; Limited Liability.

This product will be free from defects in material and manufacture for a period of 90 days from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING,

BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty

period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where

prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the

legal theory asserted.

Please recycle. Printed in USA.

RIA-2217A-D



3M Electronic Solutions Division

6801 River Place Blvd.

Austin, TX 78726-9000

U.S.A.

1-800-225-5373

www.3m.com/interconnects 3M is a trademark of 3M Company.

Appendix C3: China RoHS