2BB0435T2Ax-12 2BB0435T2Ax-12 Target Data Sheet Base Board for 2SC0435T SCALE-2 driver for 1200V IGBT modules or MOSFETs with an electrical interface for 2-level, 3-level and multilevel converter topologies with paralleling capability Abstract The 2BB0435T is a Base Board based on the SCALE-2 driver core 2SC0435T designed to drive almost all available 1200V IGBT modules like 62mm IGBT modules, 130mm x 140mm IGBT modules and others. The Base Board features an electrical interface with a built-in DC/DC power supply. The turn-on and turn-off gate resistors of both channels are not assembled in order to provide maximum flexibility. They must be assembled by the user before start of operation. Please refer to "Description & Application Manual for 2BB0435T Base Boards" for more information. For drivers adapted to various types of high-power and high-voltage IGBT modules, refer to www.IGBT-Driver.com/go/plug-and-play Features [ Easy start of operation of 2SC0435T [ Shortens application development time [ Schematics available [ Production data available (Gerber files) [ 20-pin flat cable interface [ Allows parallel connection of IGBT modules [ Safe isolation to EN 50178 [ UL compliant Applications [ 62mm IGBT modules [ 130mm x 140mm dual IGBT modules [ 130mm x 140mm single IGBT modules [ 190mm x 140mm single IGBT modules [ 17mm dual IGBT modules [ PrimePACK IGBT modules [ EconoPACK+ IGBT modules TM TM PrimePACK and EconoPACK+ are trademarks of Infineon Technologies AG, Munich www.IGBT-Driver.com Page 1 2BB0435T2Ax-12 Target Data Sheet Safety Notice! The data contained in this data sheet is intended exclusively for technically trained staff. Handling all highvoltage equipment involves risk to life. Strict compliance with the respective safety regulations is mandatory! Any handling of electronic devices is subject to the general specifications for protecting electrostatic-sensitive devices according to international standard IEC 60747-1, Chapter IX or European standard EN 100015 (i.e. the workplace, tools, etc. must comply with these standards). Otherwise, this product may be damaged. Important Product Documentation The data sheet of 2SC0435T (see www.igbt-driver.com/go/2SC0435T) applies. This data sheet contains only information which differs or completes the data contained in the data sheet of driver core 2SC0435T. For a detailed description, must-read application notes and common data that apply to the whole series, please refer to "Description & Application Manual for 2SC0435T drivers" and "Description & Application Manual for 2BB0435T Base Boards" on www.IGBT-Driver.com/go/2SC0435T and www.IGBT-Driver.com/go/2BB0435T. The turn-on and turn-off gate resistors on this Base Board are not assembled in order to provide maximum flexibility. Please refer to "Description & Application Manual for 2BB0435T Base Boards" for more information. Mechanical Dimensions Dimensions: See "Description & Application Manual for 2BB0435T Base Boards" Mounting principle: Connected to IGBT module over the connectors X2 and X3 Absolute Maximum Ratings Parameter Remarks Average supply current IDC Output power per gate Note 1 Ambient temperature <70C (Note 2) Ambient temperature 85C (Note 2) Note 3 DC-link voltage Min Max Unit 550 3 2 800 mA W W V Max Unit 4 k mA Recommended Operating Conditions Parameter Remarks Min Resistance from TB to GND SOx current Blocking time0, ext. value Fault condition, 3.3V logic 128 www.IGBT-Driver.com Typ Page 2 2BB0435T2Ax-12 Target Data Sheet Electrical Characteristics Logic Inputs and Outputs Remarks Min Typ Max Unit Input impedance SOx output voltage V(INx) > 3V Fault condition, I(SOx)<8mA 3.5 4.1 4.6 0.7 k V Short-circuit Protection Remarks Min Typ Max Unit Vce-monitoring threshold Response time Blocking time Between auxiliary terminals DC-link voltage > 550V (Note 4) After fault (Note 5) Timing Characteristics Remarks Jitter of turn-on delay Jitter of turn-off delay Dead time between outputs Jitter of dead time Note 6 Note 6 Half-bridge mode Half-bridge mode Outputs Remarks Turn-on gate resistor Rg(on) Turn-off gate resistor Rg(off) Gate resistance to COMx Note 7 Note 7 Electrical Isolation Remarks Min Creepage distance Primary to secondary side 15.7 mm Clearance distance Secondary to secondary side Primary to secondary side Secondary to secondary side 6.6 15.7 6.6 mm mm mm 10.2 7.5 90 Min Typ V s ms Max t.b.d. t.b.d. 3 t.b.d. Min Typ ns ns s ns Max not assembled not assembled 4.7 Typ Unit Max Unit k Unit All data refer to +25C and VDC = VCC = 15V unless otherwise specified Footnotes to the Key Data 1) 2) 3) 4) 5) 6) 7) If the specified value is exceeded, this indicates a Base Board overload. It should be noted that the Base Board is not protected against overload. If the specified value is exceeded, this indicates a Base Board overload. It should be noted that the Base Board is not protected against overload. From 70C to 85C, the maximum permissible output power can be linearly interpolated from the given data. This limit is due to active clamping. Refer to the "Description & Application Manual for 2BB0435T Base Boards". Resulting pulse width of the direct output of the gate drive unit for short-circuit type I (excluding the delay of the gate resistors) Factory set value. The blocking time can be reduced with an external resistor. Refer to the "Description & Application Manual for 2BB0435T Base Boards". Jitter measurements are performed with input signals INx switching between 0V and 15V referred to GND, with a corresponding rise time and fall time of 8ns. The gate resistors are not assembled on this Base Board. They must be assembled by the user. Please refer to "Description & Application Manual for 2BB0435T Base Boards". www.IGBT-Driver.com Page 3 2BB0435T2Ax-12 Target Data Sheet Legal Disclaimer This data sheet specifies devices but cannot promise to deliver any specific characteristics. No warranty or guarantee is given - either expressly or implicitly - regarding delivery, performance or suitability. CT-Concept Technologie AG reserves the right to make modifications to its technical data and product specifications at any time without prior notice. The general terms and conditions of delivery of CT-Concept Technologie AG apply. www.IGBT-Driver.com Page 4 2BB0435T2Ax-12 Target Data Sheet Ordering Information The general terms and conditions of delivery of CT-Concept Technologie AG apply. CONCEPT Base Board Type # Related IGBTs 2BB0435T2A0-12 1200V IGBT modules Note that the Base Boards 2BB0435T2A0-12 are delivered without driver 2SC0435T and without gate resistors. For orders of 1000 pieces or more (per delivery) the Base Board can be assembled with the driver 2SC0435T and the required gate resistors. Product home page: www.IGBT-Driver.com/go/2BB0435T Refer to www.IGBT-Driver.com/go/nomenclature for information on driver nomenclature Information about Other Products For drivers adapted to high-voltage or high-power IGBT modules Direct link: www.IGBT-Driver.com/go/plug-and-play For other drivers, evaluation systems product documentation and application support Please click onto: www.IGBT-Driver.com Manufacturer CT-Concept Technologie AG A Power Integrations Company Johann-Renfer-Strasse 15 2504 Biel-Bienne Switzerland Phone Fax +41 - 32 - 344 47 47 +41 - 32 - 344 47 40 E-mail Internet Info@IGBT-Driver.com www.IGBT-Driver.com (c) 2010...2013 CT-Concept Technologie AG - Switzerland. We reserve the right to make any technical modifications without prior notice. www.IGBT-Driver.com All rights reserved. Version 2.0 from 2013-02-05 Page 5 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Power Integrations: 2BB0435T2A0-12