LT1617/LT1617-1 Micropower Inverting DC/DC Converters in SOT-23 U FEATURES DESCRIPTIO The LT(R)1617/LT1617-1 are micropower inverting DC/DC converters in a 5-lead SOT-23 package. The LT1617 is designed for higher power systems with a 350mA current limit and an input voltage range of 1.2V to 15V, whereas the LT1617-1 is intended for lower power and single-cell applications with a 100mA current limit and an extended input voltage range of 1V to 15V. Otherwise, the two devices are functionally equivalent. Both devices feature a quiescent current of only 20A at no load, which further reduces to 0.5A in shutdown. A current limited, fixed offtime control scheme conserves operating current, resulting in high efficiency over a broad range of load current. The 36V switch allows high voltage outputs up to - 34V to be easily generated without the use of costly transformers. The LT1617's low off-time of 400ns permits the use of tiny, low profile inductors and capacitors to minimize footprint and cost in space-conscious portable applications. Low Quiescent Current: 20A in Active Mode <1A in Shutdown Mode Operates with VIN as Low as 1V Low VCESAT Switch: 250mV at 300mA Uses Small Surface Mount Components High Output Voltage: Up to - 34V Tiny 5-Lead SOT-23 Package U APPLICATIO S LCD Bias Handheld Computers Battery Backup Digital Cameras , LTC and LT are registered trademarks of Linear Technology Corporation. U TYPICAL APPLICATION 1-Cell Li-Ion to -15V Inverting Converter VIN 2.5V TO 4.2V 5 1 VIN SW 80 L2 22H D1 -15V 12mA 267k C2 4.7F LT1617 4 C1 4.7F SHDN NFB GND 3 24.9k 75 EFFICIENCY (%) C3 0.22F L1 22H Efficiency 70 VIN = 4.2V VIN = 2.5V 65 60 2 55 C1: TAIYO YUDEN LMK316BJ475 C2: TAIYO YUDEN EMK316BJ475 C3: TAIYO YUDEN TMK316BJ224 L1, L2: MURATA LQH3C220K34 D1: MOTOROLA MBR0530 1617/-1 TA01 50 0.1 1 10 LOAD CURRENT (mA) 30 1617/-1 TA01a 1 LT1617/LT1617-1 U W W W ABSOLUTE AXI U RATI GS U W U PACKAGE/ORDER I FOR ATIO (Note 1) VIN, SHDN Voltage ................................................... 15V SW Voltage .............................................................. 36V NFB Voltage ............................................................. - 3V Current into NFB Pin ............................................. -1mA Junction Temperature ........................................... 125C Operating Temperature Range (Note 2) .. - 40C to 85C Storage Temperature Range ................. - 65C to 150C Lead Temperature (Soldering, 10 sec).................. 300C ORDER PART NUMBER TOP VIEW SW 1 5 VIN LT1617ES5 LT1617ES5-1 GND 2 NFB 3 4 SHDN S5 PACKAGE 5-LEAD PLASTIC SOT-23 S5 PART MARKING TJMAX = 125C, JA = 256C/W LTKF LTKA Consult factory for Industrial and Military grade parts. ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 1.2V, VSHDN = 1.2V unless otherwise noted. PARAMETER CONDITIONS Minimum Input Voltage LT1617-1 LT1617 Quiescent Current Not Switching VSHDN = 0V FB Comparator Trip Point MIN -1.205 FB Comparator Hysteresis TYP 1.2V < VIN < 12V FB Pin Bias Current (Note 3) VNFB = -1.23V 1.3 Switch Off Time V V 20 30 1 A A -1.23 -1.255 V ISW = 60mA (LT1617-1) ISW = 300mA (LT1617) Switch Current Limit LT1617-1 LT1617 SHDN Pin Current VSHDN = 1.2V VSHDN = 5V SHDN Input Voltage High 0.05 0.1 %/V 2 2.7 A 75 300 ns 85 250 120 350 mV mV 100 350 125 400 mA mA 2 8 3 12 A A 0.9 V SHDN Input Voltage Low Switch Off, VSW = 5V Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: The LT1617 and LT1617-1 are guaranteed to meet specifications from 0C to 70C. Specifications over the - 40C to 85C operating temperature range are assured by design, characterization and correlation with statistical process controls. Note 3: Bias current flows out of the NFB pin. 2 mV 400 Switch VCESAT UNITS 1.0 1.2 8 Output Voltage Line Regulation Switch Leakage Current MAX 0.01 0.25 V 5 A LT1617/LT1617-1 U W TYPICAL PERFOR A CE CHARACTERISTICS Switch Saturation Voltage (VCESAT) Feedback Pin Voltage and Bias Current 0.60 Quiescent Current -1.25 5 25 4 23 VFB = 1.23V NOT SWITCHING FEEDBACK VOLTAGE (V) -1.24 0.45 ISWITCH = 500mA 0.40 0.35 0.30 ISWITCH = 300mA 0.25 0.20 VOLTAGE -1.23 3 -1.22 2 CURRENT -1.21 BIAS CURRENT (A) SWITCH VOLTAGE (V) 0.50 1 QUIESCENT CURRENT (A) 0.55 21 VIN = 12V 19 VIN = 1.2V 17 0.15 -25 0 25 50 TEMPERATURE (C) 75 100 -1.20 -50 -25 0 25 50 TEMPERATURE (C) 1617/-1 G01 400 SWITCH CURRENT LIMIT (mA) 450 VIN = 1.2V 400 VIN = 12V 350 300 0 25 50 TEMPERATURE (C) 75 300 25 VIN = 12V VIN = 1.2V LT1617 250 200 150 LT1617-1 100 Shutdown Pin Current 350 500 -25 1617/-1 G03 Switch Current Limit 550 SWITCH OFF TIME (ns) 15 -50 0 100 1617/-1 G02 Switch Off Time 250 -50 75 SHUTDOWN PIN CURRENT (A) 0.10 -50 VIN = 12V 100 VIN = 1.2V 20 15 25C 10 100C 5 50 -25 0 25 50 TEMPERATURE (C) 75 100 0 -50 0 -25 0 25 50 TEMPERATURE (C) 1617/-1 G04 75 100 0 1617/-1 G05 5 10 SHUTDOWN PIN VOLTAGE (V) 15 1617/-1 G06 U U U PI FU CTIO S SW (Pin 1): Switch Pin. This is the collector of the internal NPN power switch. Minimize the metal trace area connected to this pin to minimize EMI. GND (Pin 2): Ground. Tie this pin directly to the local ground plane. NFB (Pin 3): Feedback Pin. Set the output voltage by selecting values for R1 and R2 (see Figure 1): R1 = VOUT - 1.23 ( 1.23 + 2 * 10 -6 R2 ) SHDN (Pin 4): Shutdown Pin. Tie this pin to 0.9V or higher to enable the device. Tie below 0.25V to turn off the device. VIN (Pin 5): Input Supply Pin. Bypass this pin with a capacitor as close to the device as possible. 3 LT1617/LT1617-1 W BLOCK DIAGRA C3 L1 L2 VOUT VIN C1 5 VIN R5 80k 4 SHDN 1 D1 SW C2 R6 80k + A1 ENABLE - Q1 Q2 X10 400ns ONE-SHOT Q3 DRIVER R3 60k VOUT R1 (EXTERNAL) NFB RESET + R4 280k 0.12 3 A2 R2 (EXTERNAL) - 42mV* 2 GND 1617/-1 BD * 12mV FOR LT1617-1 Figure 1. LT1617 Block Diagram U OPERATIO The LT1617 uses a constant off-time control scheme to provide high efficiencies over a wide range of output current. Operation can be best understood by referring to the block diagram in Figure 1. Q1 and Q2 along with R3 and R4 form a bandgap reference used to regulate the output voltage. When the voltage at the NFB pin is slightly below -1.23V, comparator A1 disables most of the internal circuitry. Output current is then provided by capacitor C2, which slowly discharges until the voltage at the NFB pin goes above the hysteresis point of A1 (typical hysteresis at the NFB pin is 8mV). A1 then enables the internal circuitry, turns on power switch Q3, and the current in 4 inductors L1 and L2 begins ramping up. Once the switch current reaches 350mA, comparator A2 resets the oneshot, which turns off Q3 for 400ns. L2 continues to deliver current to the output while Q3 is off. Q3 turns on again and the inductor currents ramp back up until the switch current reaches 350mA, then A2 again resets the oneshot. This switching action continues until the output voltage is charged up (until the NFB pin reaches -1.23V), then A1 turns off the internal circuitry and the cycle repeats. The LT1617-1 operates in the same manner, except the switch current is limited to 100mA (the A2 reference voltage is 12mV instead of 42mV). LT1617/LT1617-1 U U W U APPLICATIO S I FOR ATIO Choosing an Inductor Several recommended inductors that work well with the LT1617 and LT1617-1 are listed in Table 1, although there are many other manufacturers and devices that can be used. Consult each manufacturer for more detailed information and for their entire selection of related parts. Many different sizes and shapes are available. Use the equations and recommendations in the next few sections to find the correct inductance value for your design. Table 1. Recommended Inductors PART VALUE (H) MAX DCR () VENDOR LQH3C4R7 LQH3C100 LQH3C220 4.7 10 22 0.26 0.30 0.92 Murata (714) 852-2001 www.murata.com CD43-4R7 CD43-100 CDRH4D18-4R7 CDRH4D18-100 4.7 10 4.7 10 0.11 0.18 0.16 0.20 Sumida (847) 956-0666 www.sumida.com DO1608-472 DO1608-103 D01608-223 4.7 10 22 0.09 0.16 Coilcraft (847) 639-6400 www.coilcraft.com Inductor Selection--Inverting Regulator The formula below calculates the appropriate inductor value to be used for an inverting regulator using the LT1617 or LT1617-1 (or at least provides a good starting point). This value provides a good tradeoff in inductor size and system performance. Pick a standard inductor close to this value (both inductors should be the same value). A larger value can be used to slightly increase the available output current, but limit it to around twice the value calculated below, as too large of an inductance will increase the output voltage ripple without providing much additional output current. A smaller value can be used (especially for systems with output voltages greater than 12V) to give a smaller physical size. Inductance can be calculated as: VOUT + VD L = 2 ILIM tOFF where VD = 0.4V (Schottky diode voltage), ILIM = 350mA or 100mA, and tOFF = 400ns. For higher output voltages, the formula above will give large inductance values. For a 2V to 20V converter (typical LCD bias application), a 47H inductor is called for with the above equation, but a 10H or 22H inductor could be used without excessive reduction in maximum output current. Inductor Selection--Inverting Charge Pump Regulator For the inverting regulator, the voltage seen by the internal power switch is equal to the sum of the absolute value of the input and output voltages, so that generating high output voltages from a high input voltage source will often exceed the 36V maximum switch rating. For instance, a 12V to - 30V converter using the inverting topology would generate 42V on the SW pin, exceeding its maximum rating. For such a system, an inverting charge pump is the best topology. The formula below calculates the approximate inductor value to be used for an inverting charge pump regulator using the LT1617. As for the boost inductor selection, a larger or smaller value can be used. For designs with varying VIN such as battery powered applications, use the minimum VIN value in the equation below. L= VOUT - VIN(MIN) + VD ILIM tOFF Current Limit Overshoot For the constant off-time control scheme of the LT1617, the power switch is turned off only after the 350mA (or 100mA) current limit is reached. There is a 100ns delay between the time when the current limit is reached and when the switch actually turns off. During this delay, the inductor current exceeds the current limit by a small amount. The peak inductor current can be calculated by: VIN(MAX) - VSAT IPEAK = ILIM + 100ns L Where VSAT = 0.25V (switch saturation voltage). The current overshoot will be most evident for systems with high input voltages and for systems where smaller induc- 5 LT1617/LT1617-1 U W U U APPLICATIO S I FOR ATIO tor values are used. This overshoot can be beneficial as it helps increase the amount of available output current for smaller inductor values. This will be the peak current seen by the inductor (and the diode) during normal operation. For designs using small inductance values (especially at input voltages greater than 5V), the current limit overshoot can be quite high. Although it is internally current limited to 350mA, the power switch of the LT1617 can handle larger currents without problem, but the overall efficiency will suffer. Best results will be obtained when IPEAK is kept below 700mA for the LT1617 and below 400mA for the LT1617-1. Diode Selection For most LT1617 applications, the Motorola MBR0520 surface mount Schottky diode (0.5A, 20V) is an ideal choice. Schottky diodes, with their low forward voltage drop and fast switching speed, are the best match for the LT1617. For higher output voltage applications the 30V MBR0530 can be used. Many different manufacturers make equivalent parts, but make sure that the component is rated to handle at least 0.5A. For LT1617-1 applications, a Phillips BAT54 or a Central Semiconductor CMDSH-3 works well. Lowering Output Voltage Ripple Capacitor Selection Low ESR (Equivalent Series Resistance) capacitors should be used at the output to minimize the output ripple voltage. Multilayer ceramic capacitors are the best choice, as they have a very low ESR and are available in very small packages. Their small size makes them a good companion to the LT1617's SOT-23 package. Solid tantalum capacitors (like the AVX TPS, Sprague 593D families) or OS-CON capacitors can be used, but they will occupy more board area than a ceramic and will have a larger ESR. Always use a capacitor with a sufficient voltage rating. Ceramic capacitors also make a good choice for the input decoupling capacitor, which should be placed as close as possible to the LT1617. A 4.7F input capacitor is sufficient for most applications. Table 2 shows a list of several capacitor manufacturers. Consult the manufacturers for more detailed information and for their entire selection of related parts. Using low ESR capacitors will help minimize the output ripple voltage, but proper selection of the inductor and the output capacitor also plays a big role. The LT1617 provides energy to the load in bursts by ramping up the inductor current, then delivering that current to the load. If too large of an inductor value or too small of a capacitor value is used, the output ripple voltage will increase because the capacitor will be slightly overcharged each burst cycle. To reduce the output ripple, increase the output capacitor value or add a 100pF feed-forward capacitor in the feedback network of the LT1617 (see the circuits in the Typical Applications section). Adding this small, inexpensive 100pF capacitor will greatly reduce the output voltage ripple. Table 2. Recommended Capacitors 6 CAPACITOR TYPE VENDOR Ceramic Taiyo Yuden (408) 573-4150 www.t-yuden.com Ceramic AVX (803) 448-9411 www.avxcorp.com Ceramic Murata (714) 852-2001 www.murata.com LT1617/LT1617-1 U TYPICAL APPLICATIO S 5V to - 5V Inverting Converter C3 0.47F L1 10H VIN 5V 5 1 VIN SW L2 10H -5V 100mA 100pF D1 73.2k C2 10F LT1617 4 SHDN 3 NFB GND C1 4.7F 24.9k 2 C1: TAIYO YUDEN LMK316BJ475 C2: TAIYO YUDEN JMK316BJ106 C3: TAIYO YUDEN EMK212BJ474 L1, L2: MURATA LQH3C100K24 D1: MOTOROLA MBR0520 (408) 573-4150 (408) 573-4150 (408) 573-4150 (814) 237-1431 (800) 441-2447 1617/-1 TA02 - 33V Inverting Charge Pump Converter C3 0.22F L1 10H VIN 5V 5 1 VIN SW D2 -33V 20mA D1 619k C2 1F LT1617 4 NFB SHDN 3 GND C1 4.7F 24.9k 2 C1: TAIYO YUDEN LMK316BJ475 C2: TAIYO YUDEN GMK316BJ105 C3: TAIYO YUDEN GMK212BJ224 L1: MURATA LQH3C100K24 D1: MOTOROLA MBR0540 (408) 573-4150 (408) 573-4150 (408) 573-4150 (814) 237-1431 (800) 441-2447 1617/-1 TA03 1-Cell to - 9V Inverting Converter C3 0.22F L1 47H VIN 1V TO 1.5V 5 1 VIN SW L2 47H D1 -9V 2.5mA 150k C2 4.7F LT1617-1 4 C1 4.7F SHDN NFB 3 GND 24.9k 2 C1: TAIYO YUDEN LMK316BJ475 C2: TAIYO YUDEN EMK316BJ475 C3: TAIYO YUDEN TMK316BJ224 L1, L2: MURATA LQH3C470K34 D1: CENTRAL SEMICONDUCTOR CMDSH-3 (408) 573-4150 (408) 573-4150 (408) 573-4150 (814) 237-1431 (516) 435-1110 1617/-1 TA02 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 7 LT1617/LT1617-1 U TYPICAL APPLICATIO S 20V Dual Output Converter with Load Disconnect D3 D2 C5 1F C4 1F L1 10H VIN 1.5V TO 5V 20V 4mA C3 1F 5 1 VIN SW D1 -20V 4mA 100pF D4 267k C2 1F LT1617 4 SHDN NFB 3 GND C1 4.7F C1: TAIYO YUDEN LMK316BJ475 C2, C3, C4: TAIYO YUDEN TMK316BJ105 C5: TAIYO YUDEN LMK212BJ105 L1: MURATA LQH3C100K24 D1, D2, D3, D4: MOTOROLA MBR0530 U PACKAGE DESCRIPTIO 24.9k 2 (408) 573-4150 (408) 573-4150 (408) 573-4150 (814) 237-1431 (800) 441-2447 1617/-1 TA04 Dimensions in millimeters (inches) unless otherwise noted. S5 Package 5-Lead Plastic SOT-23 (LTC DWG # 05-08-1633) 2.60 - 3.00 (0.102 - 0.118) 1.50 - 1.75 (0.059 - 0.069) 0.10 - 0.60 (0.004 - 0.024) REF 0.00 - 0.15 (0.00 - 0.006) 0.09 - 0.20 (0.004 - 0.008) (NOTE 2) 0.90 - 1.45 (0.035 - 0.057) 2.80 - 3.00 (0.110 - 0.118) (NOTE 3) 0.35 - 0.50 0.90 - 1.30 (0.014 - 0.020) (0.035 - 0.051) FIVE PLACES (NOTE 2) S5 SOT-23 0797 NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DIMENSIONS ARE INCLUSIVE OF PLATING 3. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 4. MOLD FLASH SHALL NOT EXCEED 0.254mm 5. PACKAGE EIAJ REFERENCE IS SC-74A (EIAJ) 1.90 (0.074) REF 0.95 (0.037) REF RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1307 Single-Cell Micropower 600kHz PWM DC/DC Converter 3.3V at 75mA from One Cell, MSOP Package TM LT1316 Burst Mode Operation DC/DC with Programmable Current Limit 1.5V Minimum, Precise Control of Peak Current Limit LT1317 2-Cell Micropower DC/DC with Low-Battery Detector 3.3V at 200mA from Two Cells, 600kHz Fixed Frequency LT1610 Single-Cell Micropower DC/DC Converter 3V at 30mA fro 1V, 1.7MHz Fixed Frequency LT1611 1.4MHz Inverting Switching Regulator in 5-Lead SOT-23 - 5V at 150mA from 5V Input, Tiny SOT-23 Package LT1613 1.4MHz Switching Regulator in 5-Lead SOT-23 5V at 200mA from 3.3V Input, Tiny SOT-23 Package LT1615 Micropower DC/DC Converter in 5-Lead SOT-23 20V at 12mA from 2.5V Input, Tiny SOT-23 Package Burst Mode is a trademark of Linear Technology Corporation 8 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408)432-1900 FAX: (408) 434-0507 www.linear-tech.com 16171f LT/TP 0200 4K * PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 1999