MIC3003GML TR - Micrel - Product.Network

MIC3003

FOM Management IC

with Internal Calibration

MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc.

Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com

November 2009 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

General Description

The MIC3003 is a fiber optic module controller which

enables the implementation of sophisticated, hot-pluggable

fiber optic transceivers with intelligent laser control and an

internally calibrated Digital Diagnostic Monitoring Interface

per SFF-8472. It essentially integrates all non-datapath

functions of an SFP transceiver into a tiny (4mm x 4mm)

MLF® package. It also works well as a microcontroller

peripheral in transponders or 10Gbps transceivers.

A highly configurable automatic power control (APC) circuit

controls laser bias. Bias and modulation are temperature

compensated using dual DACs, an on-chip temperature

sensor, and NVRAM look-up tables. A programmable

internal feedback resistor provides a wide dynamic range

for the APC. Controlled laser turn-on facilitates hot

plugging.

An analog-to-digital converter converts the measured

temperature, voltage, bias current, transmit power, and

received power from analog to digital. An EEPOT provides

front-end adjustment of RX power. Each parameter is

compared against user-programmed warning and alarm

thresholds. Analog comparators and DACs provide fast

monitoring of received power and critical laser operating

parameters. Data can be reported as either internally

calibrated or externally calibrated.

An interrupt output, power-on hour meter, and data-ready

bits add user friendliness beyond SFF-8472. The interrupt

output and data-ready bits reduce overhead in the host

system. The power-on hour meter logs operating hours

using an internal real-time clock and stores the result in

NVRAM.

In addition to the features listed above which are already

implemented in the previous MIC300x controllers, the

MIC3003 features an extended temperature range, options

to mask alarms and warnings interrupt and TXFAULT, a

reset signal source, and the ability to support up to four

chips with the same address on the serial interface. It also

supports eight-byte SMBus block writes.

Communication with the MIC3003 is via an industry

standard 2-wire SMBus serial interface. Nonvolatile

memory is provided for serial ID, configuration, and

separate OEM and user scratchpad spaces.

Datasheets and support documentation can be found on

Micrel’s web site at: www.micrel.com.

Features

• Extended temperature range

• Alarms and warnings interrupt and TXFAULT masks

• Capability to support up to four MIC3003 on one SMBus

• APC or constant-current laser bias

• Turbo mode for APC loop start-up and shorter laser turn

on time

• Supports multiple laser types and bias circuit topologies

• Integrated digital temperature sensor

• Temperature compensation of modulation, bias, bias fault

and alarm thresholds via NVRAM look-up tables

• NVRAM to support GBIC/SFP serial ID function

• User writable EEPROM scratchpad

• Reset signal compatible with some new systems

requirements

• Diagnostic monitoring interface per SFF-8472

– Monitors and reports critical parameters:

temperature, bias current, TX and RX optical power,

and supply voltage

– S/W control and monitoring of TXFAULT, RXLOS,

RATESELECT, and TXDISABLE

– Internal or external calibration

– EEPOT for adjusting RX power measurement

• Power-on hour meter

• Interrupt capability

• Extensive test and calibration features

• 2-wire SMBus-compatible serial interface

• SFP/SFP+ MSA and SFF-8472 compliant

• 3.0V to 3.6V power supply range

• 5V-tolerant I/O

• Available in (4mm x 4mm) 24-pin MLF® package

Applications

• SFP/SFP+ optical transceivers

• SONET/SDH transceivers and transponders

• Fibre Channel transceivers

• 10Gbps transceivers

• Free space optical communications

• Proprietary optical links

Micrel, Inc. MIC3003

November 2009 2 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Typical Application

Ordering Information

Part Number Package Type Junction Temp. Range Package Marking Lead

Finish

MIC3003GML 24-pin MLF® –45°C to +105°C 3003

with Pb-Free bar-line indicator

Pb-Free

NiPdAu

MIC3003GMLTR(1) 24-pin MLF® –45°C to +105°C 3003

with Pb-Free bar-line indicator

Pb-Free

NiPdAu

Note:

1. Tape and Reel.

Micrel, Inc. MIC3003

November 2009 3 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Contents

Pin Configuration.......................................................................................................................................................... 8

Pin Description.............................................................................................................................................................. 8

Absolute Maximum Ratings....................................................................................................................................... 10

Operating Ratings....................................................................................................................................................... 10

Electrical Characteristics........................................................................................................................................... 10

Serial Interface Timing Diagram................................................................................................................................ 14

Serial Interface Address Maps................................................................................................................................... 15

Block Diagram............................................................................................................................................................. 18

Analog-to-Digital Converter/Signal Monitoring........................................................................................................ 18

Alarms and Warnings Interrupt Source Masking..................................................................................................... 19

Alarms and Warnings as TXFAULT Source ............................................................................................................. 21

Latching of Alarms and Warnings............................................................................................................................. 21

SMBus Multipart Support........................................................................................................................................... 21

QGOP Pin Function..................................................................................................................................................... 21

Calibration Modes....................................................................................................................................................... 22

A/ External Calibration............................................................................................................................................ 22

Voltage ............................................................................................................................................................. 22

Temperature..................................................................................................................................................... 22

Bias Current ..................................................................................................................................................... 22

TX Power.......................................................................................................................................................... 22

RX Power ......................................................................................................................................................... 23

B/ Internal Calibration ............................................................................................................................................. 23

Computing Internal Calibration Results ........................................................................................................... 23

C/ Reading the ADC Result Registers.................................................................................................................... 25

RXPOT ................................................................................................................................................................... 25

Laser Diode Bias Control........................................................................................................................................ 25

Laser Modulation Control ....................................................................................................................................... 26

Power On and Laser Start-Up ................................................................................................................................ 27

Fault Comparators .................................................................................................................................................. 28

SHDN and TXFIN ................................................................................................................................................... 29

Temperature Measurement .................................................................................................................................... 30

Diode Faults............................................................................................................................................................ 30

Temperature Compensation................................................................................................................................... 30

Alarms and Warning Flags ..................................................................................................................................... 32

Control and Status I/O ............................................................................................................................................ 32

System Timing............................................................................................................................................................. 34

Warm Resets .......................................................................................................................................................... 36

Power-On Hour Meter............................................................................................................................................. 36

Test and Calibration Features ................................................................................................................................ 37

Serial Port Operation .............................................................................................................................................. 38

Block Writes............................................................................................................................................................ 38

Acknowledge Polling............................................................................................................................................... 39

Write Protection and Data Security ........................................................................................................................ 39

OEM Password................................................................................................................................................ 39

OEM Mode and User Mode............................................................................................................................. 39

Detailed Register Desc riptions.................................................................................................................................. 40

Micrel, Inc. MIC3003

November 2009 4 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Alarm Threshold Registers........................................................................................................................................ 40

Temperature High Alarm Threshold ....................................................................................................................... 40

Temperature Low Alarm Threshold ........................................................................................................................ 40

Voltage High Alarm Threshold................................................................................................................................ 40

D[7] read/write ........................................................................................................................................................ 40

D[6] read/write ........................................................................................................................................................ 40

Voltage Low Alarm Threshold ................................................................................................................................ 41

Bias Current High Alarm Threshold........................................................................................................................ 41

Bias Current Low Alarm Threshold......................................................................................................................... 41

TX Optical Power High Alarm Threshold................................................................................................................ 41

TX Optical Power Low Alarm Threshold................................................................................................................. 42

RX Optical Power High Alarm Threshold ............................................................................................................... 42

RX Optical Power Low Alarm Threshold ................................................................................................................ 42

Warning Threshold Registers.................................................................................................................................... 43

Temperature High Warning Threshold ................................................................................................................... 43

Temperature Low Warning Threshold.................................................................................................................... 43

Voltage High Warning Threshold............................................................................................................................ 43

Voltage Low Warning Threshold ............................................................................................................................ 43

Bias Current High Warning Threshold.................................................................................................................... 44

Bias Current Low Warning Threshold..................................................................................................................... 44

TX Optical Power High Warning............................................................................................................................. 44

TX Optical Power Low Warning.............................................................................................................................. 44

RX Optical Power High Warning Threshold ........................................................................................................... 45

RX Optical Power Low Warning Threshold ............................................................................................................ 45

Checksum (CHKSUM) Checksum of bytes 0 - 94 at serial address A2h............................................................... 45

ADC Result Register s................................................................................................................................................. 46

Temperature Result ................................................................................................................................................ 46

Voltage ................................................................................................................................................................... 46

Laser Diode Bias Current ....................................................................................................................................... 47

Transmitted Optical Power ..................................................................................................................................... 47

Received Optical Power ......................................................................................................................................... 48

Control and Status (CNTRL) .................................................................................................................................. 48

Application Select Control Mode (ASCM)............................................................................................................... 49

Alarm Flags............................................................................................................................................................. 50

Alarm Status Register 0 (ALARM0)........................................................................................................................ 50

Alarm Status Register 1 (ALARM1)........................................................................................................................ 50

Warning Flags.............................................................................................................................................................. 51

Warning Status Register 0 (WARN0) ..................................................................................................................... 51

Warning Status Register 1 (WARN1) ..................................................................................................................... 51

Extended Control and Status (ECNTRL)................................................................................................................ 52

OEM Password Entry (OEMPW)............................................................................................................................ 52

Power-On Hours (POHh and POHl) ....................................................................................................................... 53

Data Ready Flags (DATARDY) .............................................................................................................................. 53

User Control Register (USRCTL) ........................................................................................................................... 54

RESETOUT ............................................................................................................................................................ 55

OEM Configuration Register 0 (OEMCFG0) .......................................................................................................... 56

OEM Configuration Register 1 (OEMCFG1) .......................................................................................................... 57

OEM Configuration Register 2 (OEMCFG2) .......................................................................................................... 58

Micrel, Inc. MIC3003

November 2009 5 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

APC Setpoint 0, 1, and 2 (APCSET0, APCSET1, APCSET2) Automatic Power Control Setpoint........................ 59

Modulation Setpoint 0, 1, and 2 (MODSET0, MODSET1, and MODSET2) Nominal VMOD Setpoint ..................... 59

BIAS Fault Threshold (IBFLT) Bias Current Fault Threshold................................................................................... 60

Transmit Power Fault Threshold (TXFLT) .............................................................................................................. 60

Loss-Of-Signal Threshold (LOSFLT)...................................................................................................................... 60

Fault Suppression Timer (FLTTMR) Fault Suppression Interval in Increments of 0.5 ms ..................................... 61

Fault Mask (FLTMSK)............................................................................................................................................. 61

OEM Password Setting (OEMPWSET) .................................................................................................................. 62

OEM Calibration 0 (OEMCAL0).............................................................................................................................. 62

OEM Calibration 1 (OEMCAL1).............................................................................................................................. 64

LUT Index (LUTINDX) ............................................................................................................................................ 65

OEM Configuration 3 (OEMCFG3)......................................................................................................................... 66

BIAS DAC Setting (APCDAC) Current VBIAS Setting ........................................................................................... 66

Modulation DAC Setting (MODDAC) Current VMOD Setting................................................................................. 67

OEM Readback Register (OEMRD) ....................................................................................................................... 67

Signal Detect Threshold (LOSFLTn) ...................................................................................................................... 68

RX EEPOT Tap Selection (RXPOT)....................................................................................................................... 68

OEM Configuration 4 (OEMCFG4)......................................................................................................................... 69

OEM Configuration 5 (OEMCFG5)......................................................................................................................... 70

OEM Configuration 6 (OEMCFG6)......................................................................................................................... 71

Power-On Hour Meter Data (POHDATA)............................................................................................................... 72

OEM Scratchpad Registers (SCRATCHn) ............................................................................................................. 72

RX Power Coefficient Look-up Table (RXLUTn) .................................................................................................... 73

Calibration Constants (CALCOEFn)....................................................................................................................... 73

Manufacturer ID Register (MFG_ID) Identifies Micrel as the manufacturer of the device. Always returns 2Ah .... 74

Device ID Register (DEV_ID) ................................................................................................................................. 74

Package Information................................................................................................................................................... 75

Micrel, Inc. MIC3003

November 2009 6 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

List of Figures

Figure 1. MIC3003 Block Diagram............................................................................................................................ 18

Figure 2. Analog-to-Digital Converter Block Diagram............................................................................................... 18

Figure 3. Internal Calibration RX Power Linear Approximation................................................................................ 25

Figure 4. RXPOT Block Diagram.............................................................................................................................. 25

Figure 5. MIC3003 APC and Modulation Control Block Diagram............................................................................ 26

Figure 6. Programmable Feedback Resistor ............................................................................................................ 26

Figure 7. Transmitter Configurations Supported by MIC3003 ................................................................................. 26

Figure 8. VMOD Configured as Voltage Output with Gain ...................................................................................... 27

Figure 9. MIC3003 Power-ON Timing ...................................................................................................................... 28

Figure 10. Fault Comparator Logic ............................................................................................................................. 28

Figure 11. Saturation Detector.................................................................................................................................... 29

Figure 12. RXLOS Comparator Logic......................................................................................................................... 29

Figure 13. Control and Status I/O Logic ..................................................................................................................... 33

Figure 14. Transmitter ON-OFF Timing...................................................................................................................... 34

Figure 15. Initialization Timing with TXDISABLE Asserted ........................................................................................ 34

Figure 16. Initialization Timing with TXDISABLE Not Asserted.................................................................................. 34

Figure 17. Loss-of-Signal (LOS) Timing ..................................................................................................................... 35

Figure 18. Transmit Fault Timing................................................................................................................................ 35

Figure 19. Successfully Clearing a Fault Condition.................................................................................................... 36

Figure 20. Unsuccessful Attempt to Clear a Fault ...................................................................................................... 36

Figure 21. Write Byte Protocol.................................................................................................................................... 38

Figure 22. Read Byte Protocol.................................................................................................................................... 38

Figure 23. Read_Word Protocol ................................................................................................................................. 38

Figure 24. Eightr-Byte Block Write Protocol ............................................................................................................... 39

Micrel, Inc. MIC3003

November 2009 7 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

List of Tables

Table 1. MIC3003 Serial Interface Address Map, Device Address = A0h............................................................... 15

Table 2. MIC3003 Serial Interface Address Map, Device Address = A2h............................................................... 15

Table 3. MIC3003 Serial Interface Address Map (Temperature Compensation Tables), Device Address = A4h... 16

Table 4. MIC3003 Serial Interface Address Map (OEM Configuration Registers), Device Address = A6h............. 17

Table 5. A/D Input Signal Ranges and Resolutions ................................................................................................ 19

Table 6. VAUX Input Signal Ranges and Resolutions ............................................................................................... 19

Table 7. Alarms Interrupt Sources Masking Bits ..................................................................................................... 20

Table 8. Warnings Interrupt Sources Masking Bits ................................................................................................. 20

Table 9. RESETOUT Clear Delay ........................................................................................................................... 21

Table 10. LSB Values of Offset Coefficients ............................................................................................................. 23

Table 11. Internal Calibration Coefficient Memory Map – Part I................................................................................ 24

Table 12. Internal Calibration Coefficient Memory Map – Part II............................................................................... 24

Table 13. Shutdown State of SHDN vs. Configuration Bits...................................................................................... 27

Table 14. Shutdown State of VBIAS vs. Configuration Bits ........................................................................................ 27

Table 15. Shutdown State of VMOD vs. Configuration Bits ........................................................................................ 27

Table 16. Temperature Compensation Look-up Tables............................................................................................ 30

Table 17. APC Temperature Compensation Look-Up Table.................................................................................... 31

Table 18. IMOD Temperature Compensation Look-Up Table..................................................................................... 31

Table 19. IBIAS Comparator Temperature Compensation Look-Up Table.................................................................. 31

Table 20. BIAS Current High Alarm Temperature Compensation Table .................................................................. 31

Table 21. MIC3003 Alarm and Warning Events ........................................................................................................ 33

Table 22. Test and Diagnostic Features.................................................................................................................... 37

Micrel, Inc. MIC3003

November 2009 8 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Pin Configur ation

24-Pin MLF® (MLF-24)

Pin Description

Pin Number Pin Name Pin Function

1 FB

Analog Input. Feedback voltage for the APC loop op-amp. Polarity and scale are programmable

via the APC configuration bits I OEMCFG1. Connect to VBIAS if APC is not used.

2 VMPD

Analog Input. Multiplexed A/D converter input for monitoring transmitted optical power via a

monitor photodiode. In most applications, VMPD will be connected directly to FB. The input range

is 0 - VREF or 0 - VREF/4 depending upon the setting of the APC configuration bits

3 GNDA Ground return for analog functions.

4 VDDA Power supply input for analog functions.

5 VILD–

Analog Input. Reference terminal for the multiplexed pseudo-differential A/D converter inputs for

monitoring laser bias current via a sense resistor (VILD+ is the sensing input). Tie to VDD or GND

to reference the voltage sensed on VILD+ to VDD or GND, respectively.

6 VILD+

Analog Input. Multiplexed A/D input for monitoring laser bias current via a sense resistor (signal

input); accommodates inputs referenced to VDD or GND (see pin 5 description).

7 SHDN/TXFIN

Digital output/Input; programmable polarity. When used as shutdown output (SHDN), OEMCFG3

bit 2 set to 0, SHDN is asserted at the detection of a fault condition if OEMCFG4 bit 7 is set to 0. If

OEMCFG4 bit 7 is set to 1, a fault condition will not assert SHDN. When programmed as TXFIN, it

is an input for external fault signals to be ORed with the internal fault sources to drive TXFAULT.

8 VRX

Analog Input. Multiplexed A/D converter input for monitoring received optical power. The input

range is 0 to VREF. A 5-bit programmable EEPOT on this pin provides coarse calibration and

ranging of the RX power measurement.

9 RS1

Digital Input; Transmitter Rate Select Input; ORed with soft rate select bit SRS1 to determine the

state of the TRSOUT pin. The state of this pin is always reflected in the RS1S bit.

10 TXFAULT

Digital Output; Open-Drain, with programmable polarity. If OEMCFG5 bit 4 is set to 0, a high level

indicates a hardware fault impeding transmitter operation. If OEMCFG5 bit 4 is set to 1, a low level

indicates a hardware fault impeding transmitter operation. The state of this pin is always reflected

in the TXFLT bit.

Micrel, Inc. MIC3003

November 2009 9 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Pin Number Pin Name Pin Function

11 TXDISABLE

Digital input; Active high. The transmitter is disabled when this input is high or the STXDIS bit is

set to 1. The state of this input is always reflected in the TXDIS bit.

12 DATA Digital I/O, open-drain, bi-directional serial data input/output.

13 CLK Digital input. Serial clock input.

14 VIN/INT

If bit 4 (IE) in the USRCTL register is set to 0 (its default value), this pin is configured as an analog

input. If IE bit is set to 1, this pin is configured as an open-drain output.

Analog input: Multiplexed A/D input for monitoring supply voltage, with a 0V to 5.5V input range.

Open-drain output: outputs the internally generated active-low interrupt signal /INT.

15 RS0

Digital input. Receiver Rate Select input. ORed with soft rate select bit SRS0 to determine the

state of the RRSOUT pin. The state of this pin is always reflected in the RS0S bit.

16 GNDD Ground return for digital functions.

17 QGPO

Open-drain output. Can be selected (via OEMCFG3 bit 7) to be an open-drain GPO or an active-

low, open-drain, pulsed reset signal output controlled by the status of bits [0-2] of byte A2h: FFh.

18 VDDD Power supply input for digital functions.

19 RXLOS/

TRSOUT

Digital output. This programmable polarity, open-drain outputs has two purposes:

If OEMCFG6 bit 2 = 0, indicates the loss of the received signal as indicated by a level of received

optical power below the programmed RXLOS comparator threshold; may be wire-ORed with

external signals. Normal operation is indicated by a low level when OEMCFG6 bit 3 is set to 0 and

a high level when OEMCFG6 bit 3 is set to 1. RXLOS is de-asserted when VRX > LOSFLTn. The

LOS bit reflects the state of RXLOS whether driven by the MIC3003 or an external circuit.

If OEMCFG6 bit 2 = 1, TRSOUT is selected. This signal represents the transmitter rate select as

per the SFF specification. This output is controlled by the SRS1 bit ORed with the RS1 input.

20 RRSOUT/

GPO

Digital Output. Open-Drain or push-pull.

If OEMCFG3 bit 4 is set to 0, RRSOUT is selected. It represents the receiver rate select as per

SFF. This output is controlled by the SRS0 bit ORed with RS0 input and is open drain only.

If OEMCFG3 bit 4 is set to 1, GPO is selected. General-purpose, non-volatile output, it is

controlled by the GPO configuration bits in OEMCFG3.

21 COMP

Analog output. Compensation terminal for the APC loop. Connect a capacitor between this pin and

GNDA or VDDA with the appropriate value to tune the APC loop time constant to a desirable value.

22 VBIAS

Analog output. Buffered DAC output capable of sourcing or sinking up to 10mA under control of

the APC function to drive an external transistor or the APCSET pin of a laser diode driver for laser

diode DC bias. The output and feedback polarity are programmable to accommodate either an

NPN or a PNP transistor to drive a common-anode or common-cathode laser diode.

23 VMOD–

Analog input. This pin is the inverting terminal of the VMOD buffer op-amp. Connect to VMOD

(gain = 1) or a feedback resistor network to set a different gain value.

24 VMOD

Analog Output. Buffered DAC output to set the modulation current on the laser driver IC. Operates

with either a 0– VREF or a (VDD–VREF) – VDD output swing so as to generate either a ground-

referenced or a VDD referenced programmed voltage. A simple external circuit can be used to

generate a programmable current for those drivers that require a current rather than a voltage

input.

Micrel, Inc. MIC3003

November 2009 10 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Absolute Maximum Ratings(1)

Power Supply Voltage, VDD .......................................+3.8V

Voltage on CLK, DATA, TXFAULT, VIN, RXLOS,

TXDISABLE, RS0, RS1 ......................... –0.3V to +6.0V

Voltage On Any Other Pin.....................–0.3V to VDD+0.3V

Power Dissipation, TA = 85°C .................................... 1.5W

Junction Temperature (TJ) ....................................... 150°C

Storage Temperature (TS)....................... –65°C to +150°C

Soldering (20 sec.) ................................................... 260ºC

ESD Ratings(3)

Human Body Model.................................................. 2kV

Machine Model ....................................................... 300V

Operating Ratings(2)

Power Supply Voltage, VDDA/VDDD ........... +3.0V to +3.6V

Ambient Temperature Range (TA) .......–40°C to +105°C

Package Thermal Resistance

MLF® (θJA) .................................................43°C/W

Electrical Characteristics

For typical values, TA = 25°C, VDDA = VDDD = +3.3V, unless otherwise noted. Bold values are guaranteed for +3.0V ≤ (VDDA = VDDD)

≤ 3.6V, T(min) ≤ TA ≤ T(min), (8)

Symbol Parameter Condition Min Typ Max Units

Power Supply

CLK = DATA = VDDD = VDDA; TXDISABLE

low; all DACs at full-scale; all A/D inputs

at full-scale; all other pins open.

2.3 3.5 mA

IDD Supply Current

CLK = DATA = VDDD = VDDA; TXDISABLE

high; FLTDAC at full-scale; all A/D inputs

at full-scale; all other pins open.

2.3 3.5 mA

VPOR Power-on Reset Voltage All registers reset to default values;

A/D conversions initiated.

2.9 2.98 V

VUVLO Under-Voltage Lockout Threshold Note 5 2.5 2.73 V

VHYST Power-on Reset Hysteresis Voltage 170 mV

tPOR Power-on Reset Time VDD > VPOR, Note 4 50 µs

VREF Reference Voltage 1.210 1.225 1.240 V

ΔVREF/

ΔVDDA

Voltage Reference Line Regulation 1.7 mV/V

Temperature-to-Digital Converter Characteristics

Local Temperature Measurement

Error

–40°C ≤ TA ≤ +105°C, Note 6 ±1 ±3 °C

tCONV Conversion Time Note 4 60 ms

tSAMPLE Sample Period 100 ms

Voltage-to-Digital Converter Characteristics (VRX, VAUX, VBIAS, VMPD, VILD±)

Voltage Measurement Error –40°C ≤ TA ≤ +105°C, Note 6 ±1 ±2.0 %fs

tCONV Conversion Time Note 4 10 ms

tSAMPLE Sample Period Note 4 100 ms

Notes:

1. Exceeding the absolute maximum rating may damage the device.

2. The device is not guaranteed to function outside its operating rating.

3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF.

4. Guaranteed by design and/or testing of related parameters. Not 100% tested in production.

5. The MIC3003 will attempt to enter its shutdown state when VDD falls below VUVLO. This operation requires time to complete. If the supply voltage falls

too rapidly, the operation may not be completed.

6. Does not include quantization error.

Micrel, Inc. MIC3003

November 2009 11 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Voltage Input, VIN (Pin 14 used as an ADC Input)

Symbol Parameter Condition Min Typ Max Units

VIN Input Voltage Range –0.3 V ≤ VDD ≤ 3.6V GNDA 5.5 V

ILEAK Input Current VIN = VDD or GND; VAUX = VIN 55 µA

CIN Input Capacitance 10 pF

Digital-to-Voltage Converter Characteristics (VMOD, VBIAS)

Accuracy –40°C ≤ TA ≤ +105°C, Note 7 ±1 2.0 %fs

tCONV Conversion Time Note 8 20 ms

DNL Differential Non-linearity Error Note 8 ±0.5 ±1 LSB

Bias Current Sense Inputs, VILD+, VILD–

VILD Differential Input Signal Range,

| VILD+ – VILD– |

0 VREF/4 mV

IIN+ VILD+ input current ±1 µA

VILD– referred to VDDA +150 µA

IIN– VILD– input current

| VILD+ – VILD– | = 0.3V VILD– referred to GND -150 µA

CIN Input Capacitance 10 pF

APC Op Amp, FB, VBIAS, COMP

GBW Gain Bandwidth Product CCOMP = 20pF; Gain = 1 1 MHz

TCVOS Input Offset Voltage Temperature

Coefficient(4)

1 µV/°C

IOUT = 10mA, SRCE bit = 1 GNDA 1.25 V

VOUT Output Voltage Swing

IOUT = -10mA, SRCE bit = 0 VDDA -1.25 VDDA V

ISC Output Short-Circuit Current 55 mA

tSC Short Circuit Withstand Time TJ ≤ 150°C, Note 8 sec

CCOMP = 20pF; gain = 1, to GND 55 dB

PSRR Power Supply Rejection Ratio

CCOMP = 20pF; gain = 1, to VDD 40

AMIN Minimum Stable Gain CCOMP = 20pF, note 8 1 V/V

ΔV/Δt Slew Rate CCOMP = 20pF; gain = 1 3 V/µs

ΔRFB Internal Feedback Resistor

Tolerance

±20 %

ΔRFB/Δt Internal Feedback Resistor

Temperature Coefficient

25 ppm/C

START = 01h 0.375 mA

START = 02h 0.750 mA

START = 04h 1.500 mA

ISTART Laser Start-up Current Magnitude

START = 08h 3.000 mA

CIN Pin Capacitance 10 pF

Notes:

7. Does not include quantization error.

8. Guaranteed by design and/or testing of related parameters. Not 100% tested in production.

Micrel, Inc. MIC3003

November 2009 12 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Electrical Characteristics

Symbol Parameter Condition Min Typ Max Units

VMOD Buffer Op-Amp, VMOD, VMOD–

GBW Gain Bandwidth CCOMP = 20pF; gain = 1 1 MHz

TCVOS Input Offset Voltage Temperature

Coefficient

1 µV/°C

IBIAS V

MOD– Input Current ±0.1 ±1 µA

VOUT Output Voltage Swing IOUT = ±1mA GNDA+75 VDDA-75 mV

ISC Output Short-Circuit Current 35 mA

tSC Short Circuit Withstand Time TJ ≤ 150°C, Note 9 sec

CCOMP = 20pF; gain = 1, to GND 65 dB

PSRR Power Supply Rejection Ratio

CCOMP = 20pF; gain = 1, to VDD 44 dB

AMIN Minimum Stable Gain CCOMP = 20pF 1 V/V

ΔV/ΔT Slew Rate CCOMP = 20pF; gain = 1 1 V/µs

CIN Pin Capacitance 10 pF

Control and Status I/O, TXDISABLE, TXFAULT, RS0, RRSOUT(GPO), SHDN(TXFIN), RXLOS(TRSOUT), /INT, RS1, QGPO

VIL Low Input Voltage 0.8 V

VIH High Input Voltage 2.0 V

VOL Low Output Voltage IOL ≤ 3mA 0.3 V

VOH High Output Voltage

(applies to SHDN only)

IOH ≤ 3mA

VDDD–0.3 V

ILEAK Input Current ±1 µA

CIN Input Capacitance 10 pF

Transmit Optical Power Input, VMPD

VIN Input Voltage Range Note 9 GNDA VDDA V

BIASREF=0

VREF V

VRX Input Signal Range

BIASREF=1 VDDA–VREF VDDA V

CIN Input Capacitance Note 9 10 pF

ILEAK Input Current ±1 µA

Received Optical Power Input, VRX, RXPOT

Input Voltage Range Note 9 GNDA VDDA V

VRX Valid Input Signal Range

(ADC Input Range)

VREF V

RRXPOT(32) End-to-End Resistance RXPOT = 1Fh 32 KΩ

ΔRXPOT Resistor Tolerance ±20 %

ΔRXPOT/ΔT Resistor Temperature Coefficient 25 ppm/ºC

ΔVRX/VRXPOT Divider Ratio Accuracy 00 ≤ RXPOT ≤ 1Fh -5 +5 %

ILEAK Input Current RXPOT = 0 (disconnected) ±1 µA

CIN Input Capacitance Note 9 10 pF

ILEAK Input Current ±1 µA

Note:

9. Guaranteed by design and/or testing of related parameters. Not 100% tested in production.

Micrel, Inc. MIC3003

November 2009 13 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Electrical Characteristics

Symbol Parameter Condition Min Typ Max Units

Control and Status I/O Timing, TXFAULT, TXDISABLE, RS0, RRSOUT, and RXLOS

tOFF TXDISABLE Assert Time From input asserted to optical output

at 10% of nominal, CCOMP = 10nF.

10 µs

tON TXDISABLE De-assert Time From input de-asserted to optical output

at 90% of nominal, CCOMP = 10nF.

1 ms

tINIT Initialization Time From power on or transmitter enabled to

optical output at 90% of nominal and

TX_FAULT de-asserted. Note 10

300 ms

tINIT2 Power-on Initialization Time From power on to APC loop-enabled. 200 ms

tFAULT TXFAULT Assert Time From fault condition to TXFAULT

assertion. Note 10

95 µs

tRESET Fault Reset Time Length of time TXDISABLE must be

asserted to reset fault condition.

10 µs

tLOSS_ON RXLOS Assert Time From loss of signal to RXLOS asserted. 95 µs

tLOSS_OFF RXLOS De-assert Time From signal acquisition to LOS

de-asserted.

100 µs

tDATA Analog Parameter Data Ready From power on to valid analog

parameter data available. Note 10

400 ms

tPROP_IN TXFAULT, TXDISABLE, RXLOS,

RS0, RS1 Input Propagation Time

Time from input change to

corresponding internal register bit set or

cleared. Note 10

1 µs

tPROP_OUT TXFAULT, TRSOUT, TRRSOUT,

/INT, QGPO Output Propagation

Time

From an internal register bit set or

cleared to corresponding output change.

Note 10

1 µs

Fault Comparators

FLTTMR Fault Suppression Timer Clock

Period

Note 10 0.475 0.5 0.525 ms

Accuracy -3 +3 %/fs

tREJECT Glitch Rejection Maximum length pulse that will not

cause output to change state. Note 10

4.5 µs

High level 95 %VDDA

VSAT Saturation Detection Threshold

Low level 5 %VDDA

Power-On Hour Meter

Timebase Accuracy 0°C ≤ TA ≤ +70°, Note 10 +5 -5 %

–40°C ≤ TA ≤ +105°C +10 -10 %

Resolution Note 10 10 hours

Non-Volatile (FLASH) Memory

tWR Write Cycle Time, Note 11 Measured from the SMBus STOP

condition of a one-byte to eight-byte

write transaction. Note 10

13 ms

NVRAM Data Retention 100 years

Endurance Maximum permitted number of write

cycles to any single NVRAM location

10,000 cycles

Notes:

10. Guaranteed by design and/or testing of related parameters. Not 100% tested in production.

11. The MIC3003 will not respond to serial bus transactions during an EEPROM write cycle. The host will receive a NACK response during tWR.

Micrel, Inc. MIC3003

November 2009 14 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Serial Data I/O Pin, Data

Symbol Parameter Condition Min Typ Max Units

IOL = 3mA 0.4 V VOL Low Output Voltage

IOL = 6mA 0.6 V

VIL Low Input Voltage 0.8 V

VIH High Input Voltage 2.1 V

ILEAK Input Current

±1 µA

CIN Input Capacitance Note 12 10 pF

Serial Clock Input, CLK

VIL Low Input Voltage 2.7V ≤ VDD ≤ 3.6V 0.8 V

VIH High Input Voltage 2.7V ≤ VDD ≤ 3.6V 2.1 V

ILEAK Input Current

±1 µA

CIN Input Capacitance Note 12 10 pF

Serial Interface Timing(4)

t1 CLK (clock) Period 2.5 µs

t2 Data In Setup Time to CLK High 100 ns

t3 Data Out Stable After CLK Low 300 ns

t4 Data Low Setup Time to CLK Low Start Condition 100 ns

t5 Data High Hold Time After CLK High Stop Condition 100 ns

tDATA Data Ready Time From power on to completion of one set

of ADC conversions; analog data

available via serial interface.

400 ms

QGPO Reset Pulse Timing

t1 QGPO reset pulse low duration OEMCFG3 bit 7 = 1

A2h:255 (FFh) [2-0] switch to 111

112.5 125 137.5 µs

t2 QGPO reset de-assertion to the

clearing of A2:FFh bits 2:0

OEMCFG3 bit 7 = 1

A2h:255 (FFh) [2-0] ≠ 111

20.25 22.5 24.75 ms

Note:

12. Guaranteed by design and/or testing of related parameters. Not 100% tested in production.

Serial Interface Timing Diagram

Serial Interface Timing

Micrel, Inc. MIC3003

November 2009 15 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Serial Interface Address Maps

Address

(Decimal) Field Size

(Bytes) Name Description

0 –95 96 Serial ID defined by SFP MSA General-purpose NVRAM; R/W under valid OEM password.

96 – 127 32 Vendor Specific Vendor specific EEPROM

128 – 255 128 Reserved Reserved for future use. General-purpose NVRAM; R/W under

valid OEM password.

Table 1. MIC3003 Serial Interface Address Map, Device Address = A0h

Address(s)

Hex Dec

Field Size

(Bytes) Name Description

00-27 0-39 40 Alarm and Warning Thresholds High/low limits for warnings and alarms; writeable using the

OEM password; read-only otherwise.

28-37 40-55 16 Reserved Reserved – do not write; reads undefined.

38-5B 56-91 36 Calibration Constants Numerical constants for external calibration; writeable using

the OEM password; read-only otherwise.

5C-5E 92-94 3 Reserved Reserved – do not write; reads undefined.

5F 95 1 Checksum General-purpose NVRAM; writeable using the OEM password;

read-only otherwise.

60-69 96-105 10 Analog Data Real time analog parameter data.

6A-6D 106-109 4 Reserved Reserved – do not write; reads undefined.

6E 110 1 Control/Status Register Control and status bits.

6F 111 1 Rate Select Control Bits [7-6] control the use of the RS0 and RS1 inputs and the

SRS0 and SRS1 register bits.

70-71 112-113 2 Alarm Flags Alarm status bits; read-only.

72-73 114-115 2 Reserved Reserved – do not write; reads undefined.

74-75 116-117 2 Warning Flags Warning status bits; read-only.

76 118 1 Extended Control/Status

Additional control and status bits.

77 119 1 Reserved Reserved – do not write; reads undefined.

78-7E 120-126 7 OEMPW OEM password entry field. The four-byte OEM password

location can be selected to be 78h-7Bh (120-123) by setting

OEMCFG5 bit 2 to 0 (default) or 7Bh-7Eh (123-126) by setting

OEMCFG5 bit 2 to a one.

7F 127 1 Vendor-specific Vendor specific. Reserved – do not write; reads undefined.

80-F7 128-247 120 User Scratchpad User-writeable EEPROM. General-purpose NVRAM.

F8-F9 248-249 2 Alarms Masks Bit = 0: Corresponding alarm not masked.

Bit = 1: Corresponding alarm masked.

FA-FB 250-251 2 Warnings Masks Bit = 0: Corresponding warning not masked.

Bit = 1: Corresponding warning masked.

FC-FD 252-253 2 Reserved Reserved – do not write; reads undefined.

FE 254 1 USRCTL End-user control and status bits.

FF 255 1 RESETOUT Bits [2:0] of this register control the QGPO reset output (pin

17) If OEMCFG3 bit 7 is set to 1.

Table 2. MIC3003 Serial Interface Address Map, Device Address = A2

Micrel, Inc. MIC3003

November 2009 16 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Address(s)

Hex Dec

Field Size

(Bytes) Name Description

00-3F 0-63 64 BIASLUT1 First 64 entries of the bias current temperature compensation LUT (Look-

up Table) The additional 12 entries are located in A6: 58h – 63h.

40-7F 64-127 64 MODLUT1 First 64 entries of the modulation current temperature compensation

LUT. The additional 12 entries are located in A6:.64h – 6Fh.

80-BF 128-191 64 IFTLUT1 First 64 entries of the bias current fault threshold temperature

compensation LUT. The additional 12 entries are located in A6: 70h -

7Bh.

C0-FF 192-255 64 HATLUT1 First 64 entries of the bias current high alarm threshold temperature

compensation LUT. The additional 12 entries are located in A6: 7C-87h.

Table 3. MIC3003 Serial Interface Address Map (Temperature Compensation T ab les), Device Address = A4h

Address(s)

Hex Dec

Field Size

(Bytes) Name Description

00 0 1 OEMCFG0 OEM configuration register 0

01 1 1 OEMCFG1 OEM configuration register 1

02 2 1 OEMCFG2 OEM configuration register 2

03 3 1 APCSET0 APC setpoint register 0

04 4 1 APCSET1 APC setpoint register 1

05 5 1 APCSET2 APC setpoint register 2

06 6 1 MODSET0 Modulation setpoint register 0

07 7 1 IBFLT Bias current fault-comparator threshold. This register is temperature

compensated.

08 8 1 TXPFLT TX power fault threshold

09 9 1 LOSFLT RX LOS fault-comparator threshold

0A 10 1 FLTTMR Fault comparator timer setting

0B 11 1 FLTMSK Fault source mask bits

0C-0F 12-15 4 OEMPWSET Password for access to OEM areas

10 16 1 OEMCAL0 OEM calibration register 0

11 17 1 OEMCAL1 OEM calibration register 1

12 18 1 LUTINDX Look-up table index read-back

13 19 1 OEMCFG3 OEM configuration register 3

14 20 1 APCDAC Reads back current APC DAC value (setpoint+offset)

15 21 1 MODDAC Reads back current modulation DAC value (setpoint+offset)

16 22 1 OEMREAD Reads back OEM calibration data

17 23 1 LOSFLTn LOS deassert threshold

18 24 1 RXPOT RXPOT tap selection

19 25 1 OEMCFG4 OEM configuration register 4

1A 26 1 OEMCFG5 OEM configuration register 5

1B 27 1 OEMCFG6 OEM configuration register 6

1C-1D 28-29 2 SCRATCH Reserved – do not write; reads undefined.

1E 30 1 MODSET 1 Modulation setpoint register 1

Micrel, Inc. MIC3003

November 2009 17 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Address(s)

HEX DEC Field Si ze

(Bytes) Name Description

1F 31 1 MODSET 2 Modulation setpoint register 2

20-27 32-39 8 POHDATA Power-on hour meter scratchpad

28-47 40-71 32 RXLUT RX power internal calibration coefficient table. Eight sets of slope and

offset coefficients provide a piecewise-linear transfom for the receive

power ADC result.

48-57 72-87 16 CALCOEF Slope and offset coefficients used for temperature, voltage, bias current,

and transmit power internal calibration

58-63 88-99 12 IFTLUT2 Additional 12 entries of the bias current fault threshold temperature

compensation LUT.

64-6F 100-111 12 BIASLUT2 Additional 12 entries of the bias current temperature compensation LUT.

70-7B 112-123 12 MODLUT2 Additional 12 entries of the modulation current temperature

compensation LUT.

7C-87 124-135 12 HATLUT2 Additional 12 entries of the bias current high alarm threshold

temperature compensation LUT.

88-CF 136-207 72 SCRATCH OEM scratchpad area

D0-DD 208-221 14 RXLUTSEG/

SCRATCH

Receive power calibration segment delimiters. Each of the eight

segments can have its own slope and offset coefficient. Used to refine

the shape of the piecewise-linear function used for receive power in

internal calibration mode.

These bytes may also be part of the OEM scratch pad if the hard coded

delimiters option is selected, see the description of OEMCFG6

DE-FA 222-250 29 SCRATCH OEM scratchpad area

FB-FC 251-252 2 POH Power on hour meter result; read-only

FD 253 1 Data Ready Flags Data ready bits for each measured parameter; read-only

FE 254 1 MFG_ID Manufacturer identification (Micrel’s manufacturer ID is 42, 2Ah)

FF 255 1 DEV_ID Device ID and die revision

Table 4. MIC3003 Serial Interface Address Map (OEM Con figuration Registers), Device Address = A6h

Micrel, Inc. MIC3003

November 2009 18 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Block Diagram

Figure 1. MIC3003 Block Diagram

Analog-to-Digital Converter/Signal

Monitoring

A block diagram of the monitoring circuit is shown below.

Each of the five analog parameters monitored by the

MIC3003 is sampled in sequence. All five parameters are

sampled and the results updated within the tCONV duration

given in the “Electrical Characteristics” section. In OEM

mode, the channel that is normally used to measure VIN

may be assigned to measure the level of the VDDA pin or

one of five other nodes. This provides a kind of analog

loopback for debug and test purposes. The VAUX bits in

OEMCFG0 control which voltage source is being

sampled. The various VAUX channels are level-shifted

differently depending on the signal source, resulting in

different LSB values and signal ranges. See Table 5.

Figure 2. Analog-to -Dig ital Converter Block Diagram

Micrel, Inc. MIC3003

November 2009 19 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Channel ADC Resolution

(bits) Conditions Input Range (V) LSB(1)

TEMP 8 or 9 N/A 1°C or 0.5°C

VAUX 8 See Table 6

GAIN = 0; BIASREF = 0 GNDA - VREF

GAIN = 0; BIASREF = 1 VDDA – (VDDA – VREF)

4.77mV

GAIN = 1; BIASREF = 0 GNDA - VREF/4

VMPD 8

GAIN = 1; BIASREF = 1 VDDA – (VDDA – VREF/4)

1.17mV

VILD- = VDDA VDDA – (VDDA – VREF) VILD 8

VILD- = GNDA GNDA - VREF

4.77mV

VRX 12 RXPOT = 00 0 - VREF 0.298mV

Table 5. A/D Input Signal Ranges and Resolutions

Note:

1. Assumes typical VREF value of 1.22V.

Channel VAUX [2:0] Input Range (V) LSB(1) (mV)

VIN 000 = 00h 0.5V to 5.5V 25.6mV

VDDA 001 = 01h 0.5V to 5.5V 25.6mV

VBIAS 010 = 02h 0.5V to 5.5V 25.6mV

VMOD 011 = 03h 0.5V to 5.5V 25.6mV

APCDAC 100 = 04h 0V to VREF 4.77mV

MODDAC 101 = 05h 0V to VREF 4.77mV

FLTDAC 110 = 06h 0V to VREF 4.77mV

Table 6. VAUX Input Signal Ranges and Resolutions

Note:

1. Assumes typical VREF value of 1.22V.

Alarms and Warnings Interrupt Source Masking

Alarm and warning violations set the flags in the Alarm

and Warning Status Registers, and also assert the

interrupt output if they are not masked. If an alarm or

warning is masked, it will not set the interrupt. Table 8

shows the locations of the masking bits. The warning or

alarm is masked if the corresponding bit is set to 1.

Micrel, Inc. MIC3003

November 2009 20 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Serial Address A2h

Byte Bit Default Value Description

7 0 Masking bit for Temperature High Alarm interrupt source

6 0 Masking bit for Temperature Low Alarm interrupt source

5 0 Masking bit for Voltage High Alarm interrupt source

4 0 Masking bit for Voltage Low Alarm interrupt source

3 0 Masking bit for Bias High Alarm interrupt source

2 0 Masking bit for Bias Low Alarm interrupt source

1 0 Masking bit for TX Power High Alarm interrupt source

248

0 0 Masking bit for TX Power Low Alarm interrupt source

7 0 Masking bit for RX Power High Alarm interrupt source

6 1 Masking bit for RX Power Low Alarm interrupt source

249

[5-0] Reserved

Table 7. Alarms Interrupt Sou rces Masking Bits

Serial Address A2h

Byte Bit Default Value Description

7 0 Masking bit for Temperature High Warning interrupt

source

6 0 Masking bit for Temperature Low Warning interrupt

source

5 0 Masking bit for Voltage High Warning interrupt source

4 0 Masking bit for Voltage Low Warning interrupt source

3 0 Masking bit for Bias High Warning interrupt source

2 0 Masking bit for Bias Low Warning interrupt source

1 0 Masking bit for TX Power High Warning interrupt source

250

0 0 Masking bit for TX Power Low Warning interrupt source

7 0 Masking bit for RX Power High Warning interrupt source

6 1 Masking bit for RX Power Low Warning interrupt source

251

[5-0] Reserved

Table 8. Warnings Interru pt Sources Masking Bits

Micrel, Inc. MIC3003

November 2009 21 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Alarms and Warnings as TXFAULT Source

Alarms and warnings are not sources for TXFAULT with

the default setting. To set alarms as a TXFAULT source

set OEMCFG4 bit 6 to 1. To set warnings as a

TXFAULT, source set OEMCFG4 bit 7 to 1. The alarms

and warnings TXFAULT sources can be masked

individually in the same way shown in Tables 7 and 8.

Latching of Alarms and Warnings

Alarms and warnings are latched by default, i.e., once

asserted the flags remain ON until the register is read or

TXDSABLE is toggled. If OEMCFG4 bit 5 is set to 1, the

warnings are not latched and will be set and reset with

the warning condition. Reading the register or toggling

TXDISABLE will clear the flag. If OEMCFG4 bit 4 is set

to 1, the alarms are not latched and will be set and reset

with the alarm condition. Reading the register or toggling

TXDISABLE will clear the flag.

SMBus Multipart Support

If more than one MIC3003 device shares the same serial

interface and multipart mode is selected on them

(OEMCFG5 bit 3 = 1), then pin 7 and pin 20 become

SMBus address bits 3 and 4 respectively. Therefore, the

parts should have a different setting on those pins to

create four address combinations based upon the state

of pin 7 and pin 20 state, (00, 01, 10, 11) where 0 is a

pull down to GND and 1 is a pull up to VCC. The parts

come from the factory with the same address (A0) and

multipart mode off (OEMCFG5 bit 3 is 0). After power

up, write 1 to OEMCFG5 bit 3 to turn ON multipart mode,

which is done to all parts at the same time since they all

respond to serial address A0 at this point. With multipart

mode on, the parts have now different addresses based

on the states of pins 7 and 20. Another option is to

access each part individually, set their single mode

address in OEMCFG2 bits [4-7] to different values and

then turn off multipart mode to return to normal mode

where the parts have new different addresses.

QGOP Pin Function

QGOP can be used in GOP mode as a general purpose

output by setting OEMCFG3 bit 7 to 0, or as in RESET

mode as a reset signal output by setting OEMCFG3 bit 7

to 1.

If RESET mode is selected, the reset signal state is

controlled by RSETOUT (A2:FFh bits [2-0]). By default,

these three bits are 000, and the QGPO output is

undriven (state: High). When the three bits are written to

111, QGPO’s open-drain output will be driven low for

125 μs (typical), after which QGPO reenters the undriven

state. The RESETOUT field is cleared from 111 to 000

22.5 ms (typical) after the de-assertion edge of QGPO.

Other values of this delay may be selected by setting

TRSTCLR (OEMCFG2 bits [2-0]) to different values as

shown on table.

If Reset mode in OEMCFG3 is not selected, these three

bits have no function.

TRSTCLR

[2-0] Delay from QGPO

Switching high to

RESETOUT clear

000 Zero delay

001 17.5 ms typical

010 22.5 ms typical (default)

011 27 ms typical

100 45 ms typical

Table 9. RESETOUT Clear Delay

Micrel, Inc. MIC3003

November 2009 22 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Calibration Modes

The default mode of calibration in the MIC3003 is

external calibration, for which the INTCAL bit (bit 0 in

OEMCFG3 register) is set to 0. The internal calibration

mode is selected by setting INTCAL to 1.

A/ External Calibration

The voltage and temperature values returned by the

MIC3003’s A/D converter are internally calibrated. The

binary values of TEMPh:TEMPl and VOLTh:VOLTl are in

the format called for by SFF-8472 under Internal

Calibration.

SFF-8472 calls for a set of calibration constants to be

stored by the transceiver OEM at specific non-volatile

memory locations; refer to the SFF-8472 specifications

for the memory map of the calibration coefficients. The

MIC3003 provides the non-volatile memory required for

the storage of these constants. The Digital Diagnostic

Monitoring Interface specification should be consulted

for full details. Slopes and offsets are stored for use with

voltage, temperature, bias current, and transmitted

power measurements. Coefficients for a fourth-order

polynomial are provided for use with received power

measurements. The host system can retrieve these

constants and use them to process the measured data.

Voltage

The voltage values returned by the MIC3003’s A/D

converter are internally calibrated. The binary values of

VOLTh:VOLTl are in the format called for by SFF-8472

under Internal Calibration. Since VINh:VINl requires no

processing, the corresponding slope should be set to

one and the offset to zero.

Temperature

The temperature values returned by the MIC3003’s A/D

converter are internally calibrated. The binary values of

TEMPh:TEMPl are in the format called for by SFF-8472

under Internal Calibration.

The temperature value may be offset by storing a value

in A6:74(4Ah). The temperature offset is a six-bit signed

quantity with .5 degrees C resolution.

The temperature offset coefficient at A6:74(4Ah) is used

in the same way in both internal and external calibration

modes.

Bias Current

Bias current is sensed via an external sense resistor as

a voltage appearing between VILD+ and VILD-. The

value returned by the A/D is therefore a voltage

analogous to bias current. Bias current, IBIAS, is simply

VVILD/RSENSE. The binary value in IBIASh (IBIASl is

always zero) is related to bias current by:

(1)

The value of the least significant bit (LSB) of IBIASh is

given by:

(2)

Per SFF-8472, the value of the bias current LSB is 2µA.

The necessary conversion factor, “slope”, is therefore:

The tolerance of the sense resistor directly impacts the

accuracy of the bias current measurement. It is

recommended that the sense resistor chosen be 1%

accurate or better. The offset correction, if needed, can

be determined by shutting down the laser, i.e., asserting

TXDISABLE, and measuring the bias current. Any non-

zero result gives the offset required. The offset will be

equal and opposite to the result of the “zero current”

measurement.

TX Power

Transmit power is sensed via a resistor carrying the

monitor photodiode current. In most applications, the

signal at VMPD will be feedback voltage on FB. The

VMPD voltage may be measured relative to GND or

VDDA depending on the setting of the BIASREF bit in

OEMCFG1. The value returned by the A/D is therefore a

voltage analogous to transmit power. The binary value in

TXOPh (TXOPl is always zero) is related to transmit

power by:

(3)

For a given implementation, the value of RSENSE is

known. It is either the value of the external resistor or the

selected internal value of RFB. The constant, K, will

likely have to be determined through experimentation or

closed-loop calibration, as it depends on the monitoring

photodiode responsively and coupling efficiency.

It should be noted that the APC circuit acts to hold the

transmitted power constant. The value of transmit power

reported by the circuit should only vary by a small

amount as long as the APC is functioning correctly.

Micrel, Inc. MIC3003

November 2009 23 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

RX Power

Received power is sensed as a voltage appearing at

VRX. It is assumed that this voltage is generated by a

sense resistor carrying the receiver photodiode current

or by the RSSI circuit of the receiver. The value returned

by the A/D is therefore a voltage analogous to received

power. The binary values in RXOPh and RXOPl are

related to receive power by:

RX(mW)=K x VREF x (256 x RXOPh +RXOPl/16)/ 65536 (4)

For a given implementation, the constant, K, will likely

have to be determined through experimentation or

closed-loop calibration, as it depends upon the gain and

efficiencies of the receiver. In SFF-8472

implementations, the external calibration constants can

describe up to a fourth-order polynomial in case K is

nonlinear.

B/ Internal Calibration

If the INTCAL bit in OEMCFG3 is set to 1 (internal

calibration selected), the MIC3003 will process each

piece of data coming out of the A/D converter before

storing the result in result register. Linear slope/offset

correction will be applied on a per-channel basis to the

measured values for voltage, bias current, TX power,

and RX power. Only offset is applied to temperature.

The user must store the appropriate slope/offset

coefficients in memory at the time of transceiver

calibration. In the case of RX power, a look-up table is

provided that implements eight-segment piecewise-

linear correction. This correction may be performed as a

compensation of the receiver non-linearity over

temperature or receive power level. If static slope/offset

correction for RX power is desired, the eight coefficient

sets can simply be made the same. The user has the

option to select between using preset hard-coded

delimiters values or programmable delimiters where

delimiters corresponding to the best linear approximation

intervals of a specific receiver can be entered. The latter

option will use an additional fourteen (14) bytes from the

OEM scratch pad A6h:208-221(DOh-DDh). OEMCFG6

bits [6:5] are used to select between these options. The

memory maps for the calibration coefficients are shown

in Tables 11 and 12. If the programmable delimiters

option is selected, the user must enter the seven

delimiters of the intervals that best fit the receiver

response. The diagram in Figure 3 shows the link

between the delimiters and the sets of slopes and

offsets.

Slopes Coefficients

The slopes allow for the correction of gain errors. Each

slope coefficient is an unsigned, sixteen-bit, fixed-point

binary number in the format:

[mmmmmmmm.llllllll], (5)

where m is a data bit in the most-significant byte and l is

a data bit in the least significant byte

Slopes are always positive. The decimal point is in

between the two bytes, i.e., between bits 7 and 8. This

provides a numerical range of 1/256 (0.00391) to

255.997 in steps of 1/256. The most significant byte is

always stored in memory at the lower numerical

address.

Offset coefficients

The offsets correct for constant errors in the measured

data. Each offset, apart from temperature, is a signed,

sixteen-bit, fixed-point binary number. The bit-weights of

the offsets are the same as that of the final results. The

sixteen-bit offsets provide a numerical range of –32768

to +32767 for voltage, bias current, transmit power, and

receive power.

The numerical range for the six-bit temperature offset is

–32 (–16 °C) to +31 (+15.5 °C) in increments of .5 °C.

The two most significant bits of the temperature offset

coefficient are ignored by the MIC3003.

Computing Internal Calibration Results

Calibration of voltage, bias current, and TX power are

performed using the following calculation:

RESULTn = ADC_RESULTn x SLOPEn + OFFSETn (6)

Calibration of RX power is performed using the following

calculation:

RESULT = ADC_RESULT x SLOPE(m) + OFFSET(m) (7)

where m represents one of the eight linearization

intervals corresponding to the RX power level.

The results of these calculations are rounded to sixteen

bits. If the seventeenth bit is a one, the result is rounded

up to the next higher value. If the seventeenth bit is zero,

the upper sixteen bits remain unchanged. The bit-

weights of the offsets are the same as that of the final

results. For SFF-8472 compatible applications, these bit-

weights are given in Table 10.

Parameter Magnitude of LSB

Voltage 100µV

Bias Current 2µA

TX Power 0.1µW

RX Power 0.1µW

Table 10. LSB Values of Offset Coefficien ts

Micrel, Inc. MIC3003

November 2009 24 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Address(s)

HEX DEC

Field

Size Name Description

48-49 72-73 2 RESERVED Reserved. There is no slope for temperature. Do not write; reads undefined.

4A-4B 74-75 2 TOFFh:TOFFl Temperature offset; signed six-bit integer offset with an LSB resolution of .5

degrees C per bit. The two most significant bits of TOFFh are ignored.

TOFFl is not used.

Note that TOFFh is also used in external calibration mode.

4C-4D 76-77 2 VSLPh:VSLPl Voltage slope; unsigned fixed-point; MSB is at lower physical address.

4E-4F 78-79 2 VOFFh:VOFFl Voltage offset; signed integer; MSB is at lower physical address.

50-51 80-81 2 ISLPh:ISLPl Bias current slope; unsigned fixed-point; MSB is at lower physical address.

52-53 82-83 2 IOFFh:IOFFl Bias current offset; signed integer; MSB is at lower physical address.

54-55 84-85 2 TXSLPh: XSLPl TX power slope; unsigned fixed-point; MSB is at lower physical address.

56-57 86-87 2 TXOFFh: TXOFFl TX power slope; unsigned fixed-point; MSB is at lower physical address.

Table 11. Internal Calibration Coefficient Memor y Map – Part I

Address(s)

HEX DEC

Field

Size Name Description

28-29 40-41 2 RXSLP0h: RXSLP0l RX power slope 0; unsigned fixed-point; MSB is at lower physical address.

2A-2B 42-43 2 RXOFF0h: RXOFF0l RX power offset 0; signed integer; MSB is at lower physical address.

2C-2D 44-45 2 RXSLP1h: RXSLP1l RX power slope 1; unsigned fixed-point; MSB is at lower physical address.

2E-2F 46-47 2 RXOFF1h: RXOFF1l RX power offset 1; signed integer; MSB is at lower physical address.

30-31 48-49 2 RXSLP2h: RXSLP2l RX power slope 2; unsigned fixed-point; MSB is at lower physical address.

32-33 50-51 2 RXOFF2h: RXOFF2l RX power offset 2; signed integer; MSB is at lower physical address.

34-35 52-53 2 RXSLP3h: RXSLP3l RX power slope 3; unsigned fixed-point; MSB is at lower physical address.

36-37 54-55 2 RXOFF3h: RXOFF3l RX power offset 3; signed integer; MSB is at lower physical address.

38-39 56-57 2 RXSLP4h: RXSLP4l RX power slope 4; unsigned fixed-point; MSB is at lower physical address.

3A-3B 58-59 2 RXOFF4h: RXOFF4l RX power offset 4; signed integer; MSB is at lower physical address.

3C-3D 60-61 2 RXSLP5h: RXSLP5l RX power slope 5; unsigned fixed-point; MSB is at lower physical address.

3E-3F 62-63 2 RXOFF5h: RXOFF5l RX power offset 5; signed integer; MSB is at lower physical address.

40-41 64-65 2 RXSLP6h: RXSLP6l RX power slope 6; unsigned fixed-point; MSB is at lower physical address.

42-43 66-67 2 RXOFF6h: RXOFF6l RX power offset 6; signed integer; MSB is at lower physical address.

44-45 68-69 2 RXSLP7h: RXSLP7l RX power slope 7; signed integer; MSB is at lower physical address.

46-47 70-71 2 RXOFF7h: RXOFF7l RX power offset 7; signed fixed-point; MSB is at lower physical address.

Table 12. Internal Calibration Coefficient Memory Map – Part II

Micrel, Inc. MIC3003

November 2009 25 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Figure 3. Internal Calibration RX Power Linear Approximation

C/ Reading the ADC Result Registers

The ADC result registers should be read as 16-bit

registers under internal calibration while under external

calibration they should be read as 8-bit or 16-bit

registers at the MSB address. For example, TX power

should be read under internal calibration as 16 bits at

address A2h: 66h–67h and under external calibration as

8 bits at address A2h: 66h. 9-bit temperature results and

12-bit receive power results should always be read as

16-bit quantities.

Reading the result registers using two-byte burst reads on

the SMBus guarantees that the two bytes are coherent

with each other—that is, they form a matched result pair.

If the two bytes were read separately, it is possible that

the internal result could be updated between the reads,

leading to an incorrect ADC result.

RXPOT

A programmable, non-volatile digitally controlled

potentiometer is provided for adjusting the gain of the

receive power measurement signal chain in the analog

domain. Five bits in the RXPOT register are used to set

and adjust the position of potentiometer. RXPOT

functions as a programmable divider or attenuator. It is

adjustable in steps from 1:1 (no divider action) down to

1/32 in steps of 1/32. If RXPOT is set to zero, then the

divider is bypassed completely. There will be no scaling

of the input signal, and the resistor network will be

disconnected from the VRX pin. At all other settings of

RXPOT, there will be a 32kΩ (typical) load seen on

VRX.

Figure 4. RXPOT Block Diagram

Laser Diode Bias Control

The MIC3003 can be configured to generate a constant

bias current using electrical feedback, or regulate

average transmitted optical power using a feedback

signal from a monitor photodiode, as shown in Figure 5.

An operational amplifier is used to control laser bias

current via the VBIAS output. The VBIAS pin can drive a

maximum of ±10mA. An external bipolar transistor

provides current gain. The polarity of the op amp’s

output is programmable with BIASREF (bit-5 in

OEMCFG1) in order to accommodate either NPN or

PNP transistors that drive common anode and common

cathode laser, respectively. Additionally, the polarity of

the feedback signal is programmable for use with either

common-emitter or emitter-follower transistor circuits.

Micrel, Inc. MIC3003

November 2009 26 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Furthermore, the reference level for the APC circuit is

selectable to accommodate electrical, i.e., current

feedback, or optical feedback via a monitor photodiode.

Finally, any one of seven different internal feedback

resistors can be selected. This internal resistor can be

used alone or in parallel with an external resistor. This

wide range of adjustability (50:1) accommodates a wide

range of photodiode current, i.e., wide range of

transmitter output power. The APC operating point can

be kept near the mid-scale value of the APC DAC,

insuring maximum SNR, maximum effective resolution

for digital diagnostics, and the widest possible DAC

adjustment range for temperature compensation, etc.

See Figure 6.

The APCCAL bit in OEMCAL0 is used to turn the APC

function on and off. It will be turned on in the MIC3003’s

default state as shipped from the factory. When the APC

is on, the value in the selected APCSETx register is

added to the signed compensation value taken from the

APC look-up table and loaded into the VBIAS DAC. When

the APC is off, the VBIAS DAC may be written directly via

the VBIAS register, bypassing the look-up table entirely.

This provides direct control of the laser diode bias during

setup and calibration. In either case, the VBIAS DAC

setting is reported in the APCDAC register.

Figure 5. MIC3003 APC and Modulation Control

Block Diagram

Figure 6. Programmable Feedback Resistor

Laser Modulation Control

As shown in Figure 5, a temperature-compensated DAC

is provided to set and control the laser modulation

current via an external laser driver circuit. The MODREF

bit in OEMCFG0 selects whether the VMOD DAC output

swings up from ground or down from VDD. If the laser

driver requires a voltage input to set the modulation

current, the MIC3003’s VMOD output can drive it directly.

If a current input is required, a fixed resistor can be used

between the driver and the VMOD output. Several different

configurations are possible as shown in Figure 8.

When the APC is on, i.e., the APCCAL bit in OEMCAL0

is set to 0, the value corresponding to the current

temperature is taken from the MODLUT look-up table,

added to the selected MODSETx register, and loaded

into the VMOD DAC. When the APC is off, the

compensation value in VMOD is loaded directly into the

VMOD DAC, bypassing the look-up table entirely. This

provides for direct modulation control for setup and

calibration.

Figure 7. Transmitter Configurations

Supported by MIC3003

Micrel, Inc. MIC3003

November 2009 27 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Figure 8. VMOD Configured as Voltage Output

with Gain

Power On and Laser Start-Up

When power is applied, the MIC3003 initializes its

internal registers and state machine. This process takes

tPOR, about 50ms. Following tPOR, analog-to-digital

conversions begin, serial communication is possible, and

the POR bit and data ready bits may be polled. The first

set of analog data will be available tCONV after tPOR.

MIC3003s are shipped from the factory with the output

enable bit, OE, set to zero, off. The MIC3003’s power-up

default state, therefore, is APC off, VBIAS, VMOD, and

SHDN outputs disabled. VBIAS, VMOD, and SHDN will be

floating (high impedance) and the laser diode, if

connected, will be off. Once the device is incorporated

into a transceiver and properly configured, then the

shutdown states of SHDN, VBIAS, and VMOD will be

determined by the state of the APC configuration and

OE bits. Tables 13, 14, and 15 illustrate the shutdown

states of the various laser control outputs versus the

control bits.

Configuration Bits Shutdown State

OE SPOL SHDN

0 Don’t Care Hi-Z

1 0 GND

1 1 VDD

Table 13. Shutdown State of SHDN vs.

Configuration Bits

Configuration Bits VBIAS Shutdown State

OE INV BIASREF VBIAS

0 Don’t Care Don’t Care Hi-Z

1 Don’t Care 0 GND

1 Don’t Care 1 VDD

Table 14. Shutdown State of VBIAS vs.

Configuration Bits

Configuration Bits VMOD Shutdown State

OE MODREF VMOD

0 Don’t Care Hi-Z

1 0 GND

1 1 VDD

Table 15. Shutdown State of VMOD vs.

Configuration Bits

In order to facilitate hot-plugging, the laser diode is not

turned on until tINIT2 after Power-On. Following tINIT2, and

assuming TXDISABLE is not asserted, the DACs will be

loaded with their initial values. Since tCONV is much less

than tINIT2, the first set of analog data, including

temperature, is available at tINIT2. Temperature

compensation will be applied to the DAC values if

enabled. APC will begin if OE is asserted. (If the output

enable bit, OE, is not set, the VMOD, VBIAS, and SHDN

outputs will float indefinitely.) Figure 9 shows the power-

up timing of the MIC3003. If TXDISABLE is asserted at

power-up, the VMOD and VBIAS outputs will stay in their

shutdown states following MIC3003 initialization. A/D

conversions will begin, but the laser will remain off.

Micrel, Inc. MIC3003

November 2009 28 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Figure 9. MIC3003 Power-On Timing (OE = 1)

Fault Comparators

In addition to detecting and reporting the events specified

in SFF-8472, the MIC3003 also monitors five fault

conditions: inadequate supply voltage, thermal diode

faults, excessive bias current, excessive transmit power,

and APC op-amp saturation. Comparators monitor these

parameters in order to respond quickly to fault conditions

that could indicate link failure or safety issues, see Figure

10. When a fault is detected, the laser is shut down and

TXFAULT is asserted. Each fault source may be

independently disabled using the FLTMSK register.

FLTMSK is non-volatile, allowing faults to be masked only

during calibration and testing or permanently.

Figure 10. Fault Comparator Logic

Micrel, Inc. MIC3003

November 2009 29 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Thermal diode faults are detected within the temperature

measurement subsystem when an out-of-range signal is

detected. A window comparator circuit monitors the

voltage on the compensation capacitor to detect APC op-

amp saturation (Figure 11). Op-amp saturation indicates

that some fault has occurred in the control loop such as

loss of feedback. The saturation detector is blanked for a

time, tFLTTMR, following laser turn-on since the

compensation voltage will essentially be zero at turn-on.

The FLTTMR interval is programmable from 0.5ms to

127.5ms (typical) in increments of 0.5ms (tFLTTMR).

Note that a saturation comparator cannot be relied upon

to meet certain eye-safety standards that require 100ms

response times. This is because the operation of a

saturation detector is limited by the loop bandwidth, i.e.,

the choice of CCOMP. Even if the comparator itself was

very fast, it would be subject to the limited slew-rate of the

APC op-amp. Only the other fault comparator channels

will meet <100ms timing requirements.

The MIC3003 can also except and respond to fault inputs

from external devices. See the “SHDN and TXFIN”

section.

A similar comparator circuit monitors received signal

strength and asserts RXLOS when loss-of-signal is

detected (Figure 12). RXLOS will be asserted if VRX

drops below the level programmed in LOSFLT.

Hysteresis is implemented such that RXLOS will be de-

asserted when VRX subsequently rises above the level

programmed in LOSFLTn. The loss-of-signal comparator

may be disabled completely by setting the LOSDIS bit in

OEMCFG3. Once the LOS comparator is disabled, an

external device may drive RXLOS. The state of the

RXLOS pin is reported in the CNTRL register regardless

of whether it is driven by the internal comparator or by an

external device. A programmable digital-to-analog

converter provides the comparator reference voltages for

monitoring received signal strength, transmit power, and

bias current. Since laser bias current varies greatly with

temperature, there is a temperature compensation look-

up table for the bias current fault DAC value.

When a fault condition is detected, the laser will be

shutdown immediately and TXFAULT will be asserted.

The VMOD, VBIAS, and SHDN (if enabled by setting

OEMCFG5 bit 7 to 1) outputs will be driven to their

shutdown state according to the state of the configuration

bits. The shutdown states of VMOD, VBIAS, and SHDN

versus the configuration bit settings are shown in Table

12, Table 13, and Table 14.

SHDN and TXFIN

SHDN and TXFIN are optional functions of pin 7. SHDN

is an output function and is designed to drive a redundant

safety switch in the laser current path. TXFIN is an input

function and serves as an input for fault signals from

external devices that must be reported to the host via

TXFAULT. The SHDN function is designed for applications

in which the MIC3003 is performing all APC and laser

management tasks. The TXFIN function is for situations in

which an external device such as a laser diode driver IC is

performing laser management tasks, including fault

detection.

If the TXFIN bit in OEMCFG3 is zero (the default mode),

SHDN will be activated anytime the laser is off. Thus, it will

be active if 1) TXDISABLE is asserted, 2) STXDIS in the

CNTRL register, is set, or 3) a fault is detected. SHDN is a

push-pull logic output. Its polarity is programmable via the

SPOL bit in OEMCFG1.

If TXFIN bit is set to one, pin 7 serves as an input that

accepts fault signals from external devices such as laser

diode driver ICs. Multiple TXFAULT signals cannot simply

be wire-ORed together as they are open-drain and active

high. The input polarity is programmable via the TXFPOL

bit in OEMCFG3. TXFIN is logically ORed with the

MIC3003’s internal fault sources to produce TXFAULT and

determine the value of the transmit fault bit in CNTRL. See

Figure 10.

Figure 11. Saturation Detector

Figure 12. RXLOS Comparator Logic

Micrel, Inc. MIC3003

November 2009 30 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Temperature Measurement

The temperature-to-digital converter is built around a

switched current source and an eight-bit/nine-bit analog-

to-digital converter. The temperature is calculated by

measuring the forward voltage of a diode junction at two

different bias current levels. An internal multiplexer directs

the current source’s output to a diode junction. This data

is also used as the input to the temperature

compensation look-up tables. Each time temperature is

sampled and an updated value acquired, new corrective

values for modulation current and the APC setpoint are

read from the corresponding tables, added to the set

values, and transferred to the DACs.

Diode Faults

The MIC3003 is designed to respond in a failsafe manner

to hardware faults in the temperature sensing circuitry. If

there is a fault with the on-chip sensing diode, the

temperature data reported by the A/D converter will be

forced to its full-scale value (+127 °C). The diode fault

flag, DFLT, will be set in OEMCFG0, TXFAULT will be

asserted, and the high temperature alarm and warning

flags will be set. The reported temperature will remain at

+127 °C until the fault condition is cleared. Diode faults

may be reset by toggling TXDISABLE, as with any other

fault. Diode faults will not be detected at power up until

the first A/D conversion cycle is completed.

Temperature Compensation

Since the performance characteristics of laser diodes and

photodiodes change with operating temperature, the

MIC3003 provides a facility for temperature compensation

of the APC. loop set-point, laser modulation current, bias

current fault comparator threshold, and bias current high

alarm flag threshold. Temperature compensation is

performed using a look-up table (LUT) that stores values

corresponding to each measured temperature over a

150°C span. Four identical tables reside at serial address

A4h and A6h as summarized in Table 16. Each table

entry is a signed twos complement integer that is used as

an offset to the parameter being compensated. The

default value of all table entries is zero, giving a flat

response.

The A/D converter reports a new temperature sample

each tCONV. This occurs at roughly 10 Hz when 8-bit

temperature resolution is selected. To prevent

temperature oscillation due to thermal or electrical noise,

sixteen successive temperature samples are averaged

together and used to index the LUT.s. Temperature

compensation results are therefore updated at 16xtCONV

intervals, or about 1.6 seconds. This can be expressed as

shown in Equation 8:

(8)

Each time an updated average value is acquired, a new

offset value for the APC setpoint is read from the

corresponding look-up table (see Table 17) and transferred

to the APC circuitry. This is illustrated in Equation 11. In a

same way, new offset values are taken from similar look-up

tables (see Table 18 and Table 19), added to the nominal

values and transferred into the modulation and fault

comparator DACs. The bias current high alarm threshold is

compensated using a fourth look-up table (see Table 20).

This compensation happens internally and does not affect

any host-accessible registers.

(9)

If the measured temperature is greater than the maximum

table value, the highest value in each table is used. If the

measured temperature is less than the minimum, the

minimum value is used. Hysteresis is employed to further

enhance noise immunity and prevent oscillation. Each table

entry spans two degrees C. The table index will not change

unless the new temperature average results in a table index

beyond the midpoint of the next entry in either direction.

There is therefore 2 to 3°C of hysteresis on temperature

compensation changes. The table index will never oscillate

due to quantization noise as the hysteresis is much larger

than ±1⁄2 LSB.

Serial

Address Byte

Addresses Function

00h–3Fh APC Look-up Table

40h–7Fh IMOD Look-up Table

80h–BFh IFLT Look-up Table

Base address

+4h

C0h–FFh Bias High Alarm Look-up Table

58h–63h APC Look-up Table (cont.)

64h–6Fh IMOD Look-up Table (cont.)

70h–7Bh IFLT Look-up Table (cont.)

Base address

+6h

7Ch–87h Bias High Alarm Look-up Table

(cont.)

Table 16. Temperature Co mpensation Look-up Tables

Micrel, Inc. MIC3003

November 2009 31 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Serial Address Register

Address Table

Offset Temperature

Offset (°C)

00h 0 ≤ -45

-44 01h 1

-43

•

Base address

+4h

3Fh 63

82 64h 64

•

102 6E 74

103

Base address

+6h

6F 75 ≥ 104

Table 17. APC Temperature Compensation

Look-Up Table

Serial Address Register

Address Table

Offset Temperature

Offset (°C)

40h 0 ≤ -45

-44 41h 1

-43

•

Base address

+4h

7Fh 63

82 70 64

•

102 7A 74

103

Base address

+6h

7B 75 ≥ 104

Table 18. IMOD Temperature Compensation

Look-Up Table

Serial Address Register

Address Table

Offset Temperature

Offset (°C)

80h ≤ -45

-44 81h

-43

82h

•

BEh

Base address

+4h

BFh 63

82 58 64

•

102 62 74

103

Base address

+6h

63 75 ≥ 104

Table 19. IBIAS Comparator Temp erature Compensatio n

Look-Up Table

Serial Address Register

Address Table

Offset Temperature

Offset (°C)

C0h ≤ -45

-44 C1h

-43

C2h

•

FEh

Base address

+4h

FFh 63

82 7C 64

•

87 74 102

Base address

+6h

103

Table 20. BIAS Current High Alarm Temperature

Compensation Table

Micrel, Inc. MIC3003

November 2009 32 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

The internal state machine calculates a new table index

each time a new average temperature value becomes

available. This table index is derived from the average

temperature value. The table index is then converted into

a table address for each of the four look-up tables. These

operations can be expressed as:

(10)

where TAVG(n) is the current average temperature; and

TABLE_ADDRESS=INDEX+BASE_ADDRESS

where BASE_ADDRESS is the physical base address of

each table, i.e., 00h, 20h, 40h, 80h, or 60h (tables reside in

the Base address + 4h and Base address + 6h pages of

memory).

At any given time, the current table index can be read in

the LUTINDX register.

Alarms and Warning Flags

There are 20 different conditions that will cause the

MIC3003 to set one of the bits in the WARNx or ALARMx

registers. These conditions are listed in Table 21. The

less critical of these events generate warning flags by

setting a bit in WARN0 or WARN1. The more critical

events cause bits to be set in ALARM0 or ALARM1.

An event occurs when any alarm or warning condition

becomes true. Each event causes its corresponding

status bit in ALARM0, ALARM1, WARN0, or WARN1 to

be set. This action cannot be masked by the host. IF

OEMCFG-4 bits [7-4] are set to 0 (default value), the

status bit will remain set until the host reads that

particular status register, a power on-off cycle occurs, or

the host toggles TXDISABLE.

If TXDISABLE is asserted at any time during normal

operation, A/D conversions continue. The A/D results for

all parameters will continue to be reported. All events will

be reported in the normal way. If they have not already

been individually cleared by read operations, when

TXDISABLE is deasserted, all status registers will be

cleared.

Control and Status I/O

The logic for the transceiver control and status I/O is shown

schematically in Figure 13. Note that the internal drivers on

RXLOS/TRSOUT, RRSOUT/GPO, QGPO, and TXFAULT

are all open-drain. These signals may be driven either by

the internal logic or external drivers connected to the

corresponding MIC3003 pins. In any case, the signal level

appearing at the pins of the MIC3003 will be reported in the

control register status bits.

Note that the control bits for TX_DISABLE and RRSOUT,

TRSOUT, and the status bits for TXFAULT and RXLOS do

not meet the timing requirements as specified in the SFP

MSA or the GBIC Specification, revision 5.5 (SFF-8053) for

the hardware signals. The speed of the SMBus serial

interface limits the rate at which these functions can be

manipulated and/or reported. The response time for the

control and status bits is given in the “Electrical

Characteristics” subsection.

Micrel, Inc. MIC3003

November 2009 33 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Event Condition MIC3003 Response

Temperature high alarm TEMP > TMAX Set ALARM0[7]

Temperature low alarm TEMP < TMIN Set ALARM0[6]

Voltage high alarm VIN > VMAX Set ALARM0[5]

Voltage low alarm VIN < VMIN Set ALARM0[4]

TX bias high alarm IBIAS > IBMAX Set ALARM0[3]

TX bias low alarm IBIAS < IBMIN Set ALARM0[2]

TX power high alarm TXOP > TXMAX Set ALARM0[1]

TX power low alarm TXOP < TXMIN Set ALARM0[0]

RX power high alarm RXOP > RXMAX Set ALARM1[7]

RX power low alarm RXOP < RXMIN Set ALARM1[6]

Temperature high warning TEMP > THIGH Set WARN0[7]

Temperature low warning TEMP < TLOW Set WARN0[6]

Voltage high warning VIN > VHIGH Set WARN0[5]

Voltage low warning VIN < VLOW Set WARN0[4]

TX bias high warning IBIAS > IBHIGH Set WARN0[3]

TX bias low warning IBIAS < IBLOW Set WARN0[2]

TX power high warning TXOP > TXHIGH Set WARN0[1]

TX power low warning TXOP < TXLOW Set WARN0[0]

RX power high warning RXOP > RXHIGH Set WARN1[7]

RX power low warning RXOP < RXLOW Set WARN1[6]

Table 21. MIC3003 Alarm and Warning Events

Figure 13. Control and Status I/O Logic

Micrel, Inc. MIC3003

November 2009 34 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

System Timing

The timing specifications for MIC3003 control and status I/O are given in the “Electrical Characteristics” subsection.

Figure 14. Transmitter On-Off Timing

Figure 15. Initialization Timing with TXDISABLE Asserted

Figure 16. Initialization Timing with TXDISABLE Not Asserted

Micrel, Inc. MIC3003

November 2009 35 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Figure 17. Loss-of-Signal (LOS) Timing

Figure 18. Transmit Fault Timing

Micrel, Inc. MIC3003

November 2009 36 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Figure 19. Successfully Clearing a Fault Condition

Figure 20. Unsuccessful Attempt to Clear a Fault

Warm Resets

The MIC3003 can be reset to its power-on default state

during operation by setting the RST bit in OEMCFG0.

When this bit is set, TXFAULT and RXLOS will be de-

asserted, all registers will be restored to their normal

power-on default values, and any A/D conversion in

progress will be halted and the results discarded. The

state of the MIC3003 following this operation is

indistinguishable from a power-on reset.

Power-On Hour Meter

The Power-On Hour meter logs operating hours using an

internal real-time clock and stores the result in NVRAM.

The hour count is incremented at ten-hour intervals in the

middle of each interval. The first increment therefore

takes place five hours after power-on. Time is

accumulated whenever the MIC3003 is powered. The

hour meter’s time base is accurate to +/-10% over all

MIC3003 operating conditions, and is accurate to +/-5%

in the range 0 to 70 degrees C. The counter is capable of

storing counts of more than thirty years, but is ultimately

limited by the write-cycle endurance of the non-volatile

memory. This implies a range of at least twenty years.

Actual results will depend upon the operating conditions

and write-cycle endurance of the part in question.

Two registers, POHh and POHl, contain a 15-bit power-on

hour measurement and an error flag, POHFLT. Great care

has been taken to make the MIC3003’s hour meter immune

to data corruption and to insure that valid data is maintained

across power cycles. The hour meter employs multiple data

copies and error correction codes to maintain data validity.

This data is stored in the POHDATA registers. If POHFLT is

set, however, the power-on hour meter data has been

corrupted and should be ignored.

It is recommended that a two-byte sequential read

operation be performed on POHh and POHl to insure

coherency between the two registers. These registers are

accessible by the OEM using a valid OEM password. The

only operation that should be performed on these registers

is to clear the hour meters initial value, if necessary, at the

time of product shipment. The hour meter result may be

cleared by setting all eight POHDATA bytes to 00h.

Micrel, Inc. MIC3003

November 2009 37 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Test and Calibration Feat ures

Numerous features are included in the MIC3003 to

facilitate development, testing, and diagnostics. These

features are available via registers in the OEM area. As

shown in Table 22, these features include:

Function

Description Control

Analog loop-back Provides analog visibility of op-amp and DAC outputs via the ADC OEMCFG0

Fault comparator disable control Disables the fault comparator OEMCAL0

Fault comparator spin-on-channel

mode

Selects a single fault comparator channel OEMCAL0

Fault comparator output read-back Allows host to read individual fault comparator outputs OEMRD

TRSOUT, /INT read-back Allows host to read the state of these pins OEMRD

Inhibit EEPROM write cycles Speeds repetitive writes to registers backed up by NVRAM OEMCAL0

APC calibration mode Allows direct writes to MODDAC and APCDAC (temperature

compensation not used)

OEMCAL0

Continuity checking Forcing of RXLOS, TXFAULT, /INT OEMCAL0

Halt A/D Stops A/D conversions; ADC in one-shot mode OEMCAL1

ADC idle flag Indicates ADC status OEMCAL1

A/D one-shot mode Performs a single A/D conversion on the selected input channel OEMCAL1

A/D spin-on-channel mode Selects a single input channel OEMCAL1

Channel selection Selects ADC or fault comparator channel for spin-on-channel

modes

OEMCAL1

LUT index read-back Permits visibility of the LUT index calculated by the state-machine LUTINDX

Manufacturer and device ID registers Facilitates presence detection and version control MFG_ID,

DEV_ID

Table 22. Test and Diagno stic Features

Micrel, Inc. MIC3003

November 2009 38 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Serial Port Operation

The MIC3003 uses standard write byte, read byte, and

read word operations for communication with its host. It

also supports block write and block read transactions.

The write byte operation involves sending the devices

address (with the R/W bit low to signal a write operation),

followed by the address of the register to be operated

upon and the data byte. The read byte operation is a

composite write and read operation: the host first sends

the devices address followed by the register address, as

in a write operation. A new start bit must then be sent to

the MIC3003, followed by a repeat of the device address

with the R/W bit (LSB) set to the high (read) state. The

data to be read from the part may then be clocked out. A

read word is similar, but two successive data bytes are

clocked out rather than one. These protocols are shown

in Figures 21 to 24.

The MIC3003 will respond to up to four sequential device

addresses depending upon whether it is in OEM or User

mode. A match between one of the MIC3003’s addresses

and the address specified in the serial bit stream must be

made to initiate communication. The MIC3003 responds

to device addresses A0h and A2h in User Mode; it also

responds to A4h and A6h in OEM Mode (assuming the

base address is A0h).

Block Writes

To increase the speed of block writes, the MIC3003 allows

up to eight consecutive bytes to be written before the

internal memory update begins.

The block write sequence begins just like a write byte

operation with the host sending the device address, R/W bit

low, register address, etc. After the first data byte is sent

the host will receive an acknowledge. Up to seven more

bytes can be sent in sequence. The MIC3003 will

acknowledge each one and increment its internal address

sent, the host issues a STOP. The MIC3003’s internal write

process then begins.

Block writes of up to eight bytes can begin and end at any

byte address without restriction. Block writes that increment

over register address FFh will simply “wrap around” and

continue at address 00h within the same device address

space.

To accelerate calibration and testing, NVRAM write cycles

can be disabled completely by setting the WRINH bit in

OEMCAL0. Writes to registers that do not have NVRAM

backup, will not incur write-cycle delays when writes are

inhibited. Write operations on registers that exist only in

NVRAM will still incur write cycle delays.

Figure 21. Write Byte Protocol

Figure 22. Read Byte Protocol

Figure 23. Read_Word Protocol

Micrel, Inc. MIC3003

November 2009 39 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Figure 24. Eight-Byte Block Write Protocol

Acknowledge Polling

The MIC3003’s non-volatile memory cannot be accessed

during the internal memory update. To allow for maximum

speed bulk writes, the MIC3003 supports acknowledge

polling. The MIC3003 will not acknowledge serial bus

transactions while internal writes are in progress. The

host may therefore monitor for the end of the write

process by periodically checking for an

acknowledgement. The longest duration for the internal

memory update to complete for a block write is

approximately 26 ms.

Write Protection and Data Security

OEM Password

A password is required to access the OEM areas of the

MIC3003, specifically the non-volatile memory, look-up

tables, and registers at serial addresses A4h and A6h. A

four-byte field, OEMPWSET, at serial address A6h is

used for setting the OEM password. The OEM password

is set by writing OEMPWSET with the new value. The

password comparison is performed following the write to

the MSB of the OEMPW, address 7Bh (or 7Eh if

OEMCFG5 bit 2 is set to 1) at serial address A2h.

Therefore, this byte must be written last. A four-byte

burst-write sequence to address 78h (or 7Bh if OEMCFG5

bit 2 is set to 1) may be used as this will result in the

MSbyte being written last. New passwords written to the

OEMPWSET registers will not take effect until after a

power-on reset occurs or a warm reset is performed using

the RST bit in OEMCFG0. This allows the new password

to be verified before it takes effect.

The corresponding four-byte field for password entry,

OEMPW, is located at serial address A2h. This field is

therefore always visible to the host system. OEMPW is

compared to the four-byte OEMPWSET field at serial

address A6h. If the two fields match, access is allowed to

the OEM areas of the MIC3003 non-volatile memory at

serial addresses A4h and A6h. If OEMPWSET is all zeroes,

no password security will exist. The value in OEMPW will

be ignored. This helps prevent a deliberately unsecured

MIC3003 from being inadvertently locked. Once a valid

password is entered, the MIC3003 OEM areas will be

accessible. The OEM areas may be re-secured by writing

an incorrect password value at OEMPW, e.g., all zeroes. In

all cases, OEMPW must be written LSB first through MSB

last. The OEM areas will be inaccessible following the final

write operation to OEMPW’s LSB. The OEMPW field is

reset to all zeros at power on. Any values written to these

locations will be readable by the host regardless of the

locked/unlocked status of the device. If OEMPWSET is set

to zero (00000000h), the MIC3003 will remain unlocked

regardless of the contents of the OEMPW field. This is the

factory default security setting.

Note that a valid OEM password allows access to the OEM

and user areas of the chip, i.e., the entire memory map.

OEM Mode and User Mode

When the OEM password is unlocked (either by matching

the set password or if the password is all zeros), the

MIC3003 is in OEM Mode. If the part is locked, the part is in

User Mode.

Micrel, Inc. MIC3003

November 2009 40 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Detailed Register Descriptions

Note: Serial bus addresses shown assume that the base device address is AOh.

Alarm Threshold Registers

Temperature High Alarm Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 °C)

Serial address A2h

Byte addresses MS byte (TMAXh): 00 = 00h

LS byte (TMAXl): 01 = 01h

Each LS bit of TMAXh represents one degree Celsius. TMAXl is not used, since all limit comparisons for temperature use

eight-bit values.

The eight bits of the high alarm threshold value (TMAXh) are compared to the temperature result (TEMPh). ALARM0 bit 7 is

set if Result > Threshold.

Temperature Low Alarm Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 °C)

Serial address A2h

Byte addresses MS byte (TMINh): 02 = 02h

LS byte (TMINl): 03 = 03h

Each LS bit of TMINh represents one degree Celsius. TMINl is not used, since all limit comparisons for temperature use eight-

bit values..

The eight MS bits of the low alarm threshold value (TMINh) are compared to the temperature result (TEMPh). ALARM0 bit 6 is

set if Result < Threshold.

Voltage High Alarm Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 V)

Serial address A2h

Byte addresses MS byte (VMAXh): 08 = 08h

LS byte (VMAXl): 09 = 09h

Each LS bit of VMAXh represents 25.6 mV and each LS bit of VMAXl represents 0.1 mV. The sixteen-bit threshold value

(VMAXh:VMAXl) is compared to the sixteen bits value of the voltage result (VINh:VINl). ALARM0 bit 5 is set if

Result > Threshold.

Micrel, Inc. MIC3003

November 2009 41 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Voltage Low Alarm Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 V)

Serial address A2h

Byte addresses MS byte (VMINh): 10 = 0Ah

LS byte (VMINl): 11 = 0Bh

Each LS bit of VMINh represents 25.6 mV and each LS bit of VMINl represents 0.1 mV. The sixteen-bit threshold value

(VMINh:VMINl) is compared to the sixteen-bit value of the voltage result (VINh:VINl). ALARM0 bit 4 is set if Result < Threshold.

Bias Current High Alarm Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 mA)

Serial address A2h

Byte addresses MS byte (IMAXh): 16 = 10h

LS byte (IMAXl): 17 = 11h

Each LS bit of IMAXh represents 512 μA and each LS bit of IMAXl represents 2 μA. The sixteen-bit threshold value

(IMAXh:IMAXl) is compared,to the sixteen-bit value of the bias current result (ILDh:ILDl). ALARM0 bit 3 is set if Result >

Threshold.

Bias Current Low Alarm Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 mA)

Serial address A2h

Byte addresses MS byte (IMINh): 18 = 12h

LS byte (IMINl): 19 = 13h

Each LS bit of IMINh represents 512 μA and each LS bit of IMINl represents 2 μA. The sixteen-bit threshold value

(IMINh:IMINl) is compared to the sixteen-bit value of the bias current result (ILDh:ILDl). ALARM0 bit 2 is set if

Result < Threshold.

TX Optical Power High Alarm Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 mW)

Serial address A2h

Byte addresses MS byte (TXMAXh): 24 = 18h

LS byte (TXMAXl): 25 = 19h

Each LS bit of TXMAXh represents 25.6 μW, and each LS bit of TXMAXl represents 0.1 μW. The sixteen-bit threshold value

(TXMAXh:TXMAXl) is compared to the sixteen-bit value of the TX power result (TXOPh:TXOPl). ALARM0 bit 1 is set if Result >

Threshold.

Micrel, Inc. MIC3003

November 2009 42 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

TX Optical Power Low Alarm Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 mW)

Serial address A2h

Byte addresses MS byte (TXMINh): 26 = 1Ah

LS byte (TXMINl): 27 = 1Bh

Each LS bit of TXMINh represents 25.6 μW, and each LS bit of TXMINl represents 0.1 μW. The sixteen-bit threshold value

(TXMINh:TXMINl) is compared,to the sixteen-bit value of the TX power reading (TXOPh:TXOPl). ALARM0 bit 0 is set if

Result < Threshold.

RX Optical Power High Alarm Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 mW)

Serial address A2h

Bytes addresses MS byte (RXMAXh): 32 = 20h

LS byte (RXMAXl): 33 = 21h

Each LS bit of RXMAXh represents 25.6 μW, and each LS bit of RXMAXl represents 0.1 μW. The sixteen-bit threshold value

(RXMAXh:RXMAXl) is compared to the sixteen-bit value of the RX power result (RXOPh:RXOPl). ALARM1 bit 7 is set if

Result > Threshold.

RX Optical Power Low Alarm Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0mW)

Serial Address A2h

Byte Address MS byte (RXMINh): 34 = 22h

LS byte (RXMINl): 35 = 23h

Each LSB of RXMINh represents 25.6 μW, and each LS bit of RXMINl represents 0.1 μW. The sixteen-bit threshold value

(RXMINh:RXMINl) is compared to the sixteen-bit value of the RX power result (RXOPh:RXOPl). ALARM1 bit 6 is set if

Result < Threshold.

Micrel, Inc. MIC3003

November 2009 43 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Warning Thres hold Register s

Temperature High Warning Thre s hold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 °C)

Serial address A2h

Bytes addresses MS byte (THIGHh): 04 = 04h

LS byte (THIGHl): 05 = 05h

Each LS bit of THIGHh represents one degree Celsius. THIGHl is not used, since all limit comparisons for temperature use

eight-bit values.

The eight bits of the high warning threshold value (THIGHh) are compared to the temperature result (TEMPh). WARN0 bit 7 is

set if Result > Threshold.

Temperature Lo w Warning Thres hold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 °C)

Serial address A2h

Bytes addresses MS byte (TLOWh): 06 = 06h

LS byte (TLOWl): 07 = 07h

Each LS bit of TLOWh represents one degree Celsius. TLOWl is not used, since all limit comparisons for temperature use

eight-bit values.

The eight bits of the high warning threshold value (TLOWh) are compared to the temperature result (TEMPh). WARN0 bit 6 is

set if Result < Threshold.

Voltage High Warning Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 V)

Serial address A2h

Bytes addresses MS byte (VHIGHh): 12 = 0Ch

LS byte (VHIGHl): 13 = 0Dh

Each LS bit of VHIGHh represents 25.6 mV and each LS bit of VHIGHl represents 0.1 mV. The sixteen-bit threshold value

(VHIGHh:VHIGHl) is compared to the sixteen bits value of the voltage result (VINh:VINl). WARN0 bit 5 is set if

Result > Threshold.

Voltage Low Warning Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 V)

Serial address A2h

Byte addresses MS byte (VLOWh): 14 = 0Eh

LS byte (VLOWl): 15 = 0Fh

Each LS bit of VLOWh represents 25.6 mV and each LS bit of VLOWl represents 0.1 mV. The sixteen-bit threshold value

(VLOWh:VLOWl) is compared to the sixteen-bit value of the voltage result (VINh:VINl). WARN0 bit 4 is set if

Result < Threshold.

Micrel, Inc. MIC3003

November 2009 44 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Bias Current High Warning Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 mA)

Serial address A2h

Bytes addresses MS byte (IHIGHh): 20 = 14h

LS byte (IHIGHl): 21 = 15h

Each LS bit of IHIGHh represents 512 μA and each LS bit of IHIGHl represents 2 μA. The sixteen-bit threshold value

(IHIGHh:IHIGHl) is compared,to the sixteen-bit value of the bias current result (ILDh:ILDl). WARN0 bit 3 is set if Result >

Threshold.

Bias Current Low Warning Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 mA)

Serial address A2h

Bytes addresses MS byte (ILOWh): 22 = 16h

LS byte (ILOWl): 23 = 17h

Each LS bit of ILOWh represents 512 μA and each LS bit of ILOWl represents 2 μA. The sixteen-bit threshold value

(ILOWh:ILOWl) is compared to the sixteen-bit value of the bias current result (ILDh:ILDl). WARN0 bit 2 is set if

Result < Threshold.

TX Optical Power High Warning

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 mW)

Serial address A2h

Bytes addresses MS byte (TXHIGHh): 28 = 1Ch

LS byte (TXHIGHl): 29 = 1Dh

Each LS bit of TXHIGHh represents 25.6 μW, and each LS bit of TXHIGHl represents 0.1 μW. The sixteen-bit threshold value

(TXHIGHh:TXHIGHl) is compared to the sixteen-bit value of the TX power result (TXOPh:TXOPl).WARN0 bit 1 is set if Result >

Threshold.

TX Optical Power Low Warning

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 mW)

Serial address A2h

Byte addresses MS byte (TXLOWh): 30 = 1Eh

LS byte (TXLOWl): 31 = 1Fh

Each LS bit of TXLOWh represents 25.6 μW, and each LS bit of TXLOWl represents 0.1 μW. The sixteen-bit threshold value

(TXLOWh:TXLOWl) is compared,to the sixteen-bit value of the TX power reading (TXOPh:TXOPl). ALARM0 bit 0 is set if

Result < Threshold.

Micrel, Inc. MIC3003

November 2009 45 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

RX Optical Power High Warning Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 mW)

Serial address A2h

Byte addresses MS byte (RXHIGHh): 36 = 24h

LS byte (RXHIGHl): 37 = 25h

Each LS bit of RXHIGHh represents 25.6 μW, and each LS bit of RXHIGHl represents 0.1 μW. The sixteen-bit threshold value

(RXHIGHh:RXHIGHl) is compared to the sixteen-bit value of the RX power result (RXOPh:RXOPl). WARN1 bit 7 is set if

Result > Threshold.

RX Optical Power Low Warning Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for both bytes 0000 0000b = 00h (0 mW)

Serial address A2h

Byte addresses MS byte (RXLOWh): 38 = 26h

LS byte (RXLOWl): 39 = 27h

Each LSB of RXLOWh represents 25.6 μW, and each LS bit of RXLOWl represents 0.1 μW. The sixteen-bit threshold value

(RXLOWh:RXLOWl) is compared to the sixteen-bit value of the RX power result (RXOPh:RXOPl). WARN1 bit 6 is set if

Result < Threshold.

Checksum (CHKSUM)

Checksum of bytes 0 - 94 at serial address A2h

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value 0000 0000b = 00h

Serial address A2h

Byte address 95 = 5Fh

This register is provided for compliance with SFF-8472. It is implemented as general-purpose non-volatile memory. Read/write

access is possible whenever a valid OEM password has been entered. CHKSUM is read-only in User Mode.

Micrel, Inc. MIC3003

November 2009 46 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

ADC Result Registers

Temperature Result

D[7]

read-only

D[6]

read-only

D[5]

read-only

D[4]

read-only

D[3]

read-only

D[2]

read-only

D[1]

read-only

D[0]

read-only

Serial address A2h

Byte addresses MS byte (TEMPh): 96 = 60h

LS byte (TEMPl): 97 = 61h

Each LS bit of TEMPh represents one degree Celsius. The TEMPh register is to be used in conjunction with the most

significant bit of TEMPl to yield an eight-bit or nine-bit signed (two’s complement) temperature value.

If OEMCFG6 bit 1 is set to zero, temperature is read to 1 °C resolution in TEMPh only, and TEMPl is zero.

If OEMCFG6 bit 1 is set to one, then temperature is read to 0.5 °C resolution as a nine-bit value consisting of TEMPh and the

MS bit of TEMPl. The lower seven bits of TEMPl are zero.

TEMPh will contain measured temperature data after the completion of one conversion.

Voltage

D[7]

read-only

D[6]

read-only

D[5]

read-only

D[4]

read-only

D[3]

read-only

D[2]

read-only

D[1]

read-only

D[0]

read-only

Default Value 0000 0000b = 00h (0V)(2)

Serial address A2h

Byte addresses MS byte (VINh): 98 = 62h

LS byte (VINl): 99 = 63h

Each LSB of VINh represents 25.6 mV, and each LS bit of VINl represents 0.1 mV. VINh is used in conjunction with VINl to

yield an unsigned sixteen-bit value.

In external calibration mode, the host should process the results using the appropriate slope and offset coefficients. VINh

contains the eight-bit ADC result and VINl is zero.

In internal calibration mode, the MIC3003’s ALU applies the coefficients stored in (VSLPh:VSLPl) and (VOFFh:VOFFl).

The VIN registers will contain valid data after one ADC conversion cycle.

Notes:

1. TEMPh will contain measured temperature data after the completion of one conversion.

2. VINh will contain measured data after one A/D conversion cycle.

Micrel, Inc. MIC3003

November 2009 47 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Laser Diode Bias Current

D[7]

read-only

D[6]

read-only

D[5]

read-only

D[4]

read-only

D[3]

read-only

D[2]

read-only

D[1]

read-only

D[0]

read-only

Default Value 0000 0000b = 00h (0mA)(3)

Serial address A2h

Byte addresses MS byte (ILDh):100 = 64h

LS byte (ILDl):101 = 65h

Each LSB of ILDh represents 512 μA, and each LS bit of ILDl represents 2 μA. ILDh is used in conjunction with ILDl to yield an

unsigned sixteen-bit value.

In external calibration mode, the host should process the results using the appropriate slope and offset coefficients. ILDh

contains the eight-bit ADC result and ILDl is zero.

In internal calibration mode, the MIC3003’s ALU applies the coefficients stored in (ISLPh:ISLPl) and (IOFFh:IOFFl).

The ILD registers will contain valid data after one ADC conversion cycle.

Transmitted Optical Power

D[7]

read-only

D[6]

read-only

D[5]

read-only

D[4]

read-only

D[3]

read-only

D[2]

read-only

D[1]

read-only

D[0]

read-only

Default Value 0000 0000b = 00h (0mW)(4)

Serial address A2h

Byte address MS byte (TXOPh): 102 = 66h

LS byte (TXOPl): 103 = 67h

Each LSB of TXOPh represents 25.6 μW, and each LS bit of TXOPl represents 0.1 μW. TXOPh is used in conjunction with

TXOPl to yield an unsigned sixteen-bit value.

In external calibration mode, the host should process the results using the appropriate slope and offset coefficients. TXOPh

contains the eight-bit ADC result and TXOPl is zero.

In internal calibration mode, the MIC3003’s ALU applies the coefficients stored in (TXSLPh:TXSLPl) and (TXOFFh:TXOFFl).

The TXOP registers will contain valid data after one ADC conversion cycle.

Notes:

3. ILDh will contain measured data after one A/D conversion cycle.

4. TXOPh will contain measured data after one A/D conversion cycle.

Micrel, Inc. MIC3003

November 2009 48 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Received Optical Power

D[7]

read-only

D[6]

read-only

D[5]

read-only

D[4]

read-only

D[3]

read-only

D[2]

read-only

D[1]

read-only

D[0]

read-only

Default Value 0000 0000b = 00h (0mW)(6)

Serial address A2h

Byte address MS byte (RXOPh): 104 = 68h

LS byte (RXOPl): 105 = 69h

Each LSB of RXOPh represents 25.6 μW, and each LS bit of RXOPl represents 0.1 μW.RXOPh is used in conjunction with

RXOPl to yield an unsigned sixteen-bit value.

In external calibration mode, the host should process the results using the appropriate slope and offset coefficients. RXOPh

contains the twelve-bit ADC result and the lower four bits of RXOPl are zero.

In internal calibration mode, the MIC3003’s ALU applies the coefficients stored in (RXSLP[0-7]h:RXSLP[0-7]l) and

(RXOFF[0-7]h:RXOFFl[0-7]).

The RXOP registers will contain valid data after one ADC conversion cycle.

Control and Status (CNTRL)

D[7]

TXDIS

read-only

D[6]

STXDIS

read/write

D[5]

RS1S

read-only

D[4]

RS0S

read-only

D[3]

SRS0

read/write

D[2]

TXFLT

read-only

D[1]

LOS

read-only

D[0]

POR

read-only

Default value 0000 0000b = 00h

Serial address A2h

Byte address 110 = 6Eh

Bit(s) Function Operation

D[7] TXDIS Reflects the state of the TXDISABLE pin 1 = disabled,

0 = enabled

D[6] STXDIS

Soft transmit disable STXDIS is Ored with TXDIS

to control the laser which will be turned off if one

of these two signals is set to 1

1 = disabled

0 = enabled

D[5] RS1S Reflects the state of RS1 (pin 9) 1 = RS1 is high (>4.25 Gbps);

0 = RS1 is low (≤4.25 Gbps)

D[4] RS0S Reflects the state of RS0 (pin 15) 1 = RS0 is high (>4.25 Gbps)

0 = RS0 is low (≤4.25 Gbps)

D[3] SRS0 Soft rate select (sets the state of the RS0 pin) 1 = Set RS0 high

0 = Set RS0 low

D[2] TXFLT Reflects the state of the TXFAULT pin 1 = TXFAULT is high (fault)

0 = TXFAULT low (no fault)

D[1] LOS

Loss Of Signal. Reflects the state of the RXLOS

1 = RXLOS is high (loss of signal)

0 = RXLOS is low (no loss of signal)

D[0] POR MIC3003 power-on status 0 = POR complete, all analog data results

have been converted at least once

1 = POR and first ADC sample cycle in

progress

Micrel, Inc. MIC3003

November 2009 49 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Application Select Control Mode (ASCM)

D[7-6]

Control bits

read/write

D[5-0]

Table select

read/write

Default value 0000 0000b = 00h

Serial address A2h

Byte address 111 = 6Fh

Bit(s) Function Operation

D[7-6] Application Select Control Bits

D[5-0] Table Select

Bit 7 Bit 6

0 0 Rate Select/Extended Rate Select Emulation Mode:

• RS0 (pin 7) controls RRSOUT( pin 20)

• RS1 (pin 9) does not control TRSOUT (pin 19)

• Byte 110 bit 3 controls RRSOUT (pin 20)

• Byte 118 bit 3 controls TRSOUT (pin 19)

0 1 Hardware Application Select Mode:

• RS0 (pin 7) controls RRSOUT( pin 20)

• RS1 (pin 9) controls TRSOUT (pin 19)

• Byte 110 bit 3 does not control RRSOUT (pin 20)

• Byte 118 bit 3 does not control TRSOUT (pin 19)

1 X Software Mode:

• RS0 (pin 7) does not control RRSOUT( pin 20)

• RS1 (pin 9) does not control TRSOUT (pin 19)

• Byte 110 bit 3 does not control RRSOUT (pin 20)

• Byte 118 bit 3 does not control TRSOUT (pin 19)

Micrel, Inc. MIC3003

November 2009 50 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Alarm Flags

Alarm Status Register 0 (ALARM0)

D[7]

read-only

D[6]

read-only

D[5]

read-only

D[4]

read-only

D[3]

read-only

D[2]

read-only

D[1]

read-only

D[0]

read-only

Default value 0000 0000b = 00h (no events pending)

Serial address A2h

Byte address 112 = 70h

The power-up default value is 00h. Following the first complete A/D conversion cycle, however, any of the bits may be set

depending upon the results.

Bit(s) Function Operation

D[7] A7 High temperature alarm, TEMP > TMAX 1 = condition exists, 0 = normal/OK

D[6] A6 Low temperature alarm, TEMP < TMIN 1 = condition exists, 0 = normal/OK

D[5] A5 High voltage alarm, VIN > VMAX 1 = condition exists, 0 = normal/OK

D[4] A4 Low voltage alarm, VIN < VMIN 1 = condition exists, 0 = normal/OK

D[3] A3 High laser diode bias alarm, IBIAS > IMAX 1 = condition exists, 0 = normal/OK

D[2] A2 Low laser diode bias alarm, IBIAS < IMIN 1 = condition exists, 0 = normal/OK

D[1] A1

High transmit optical power alarm,

TXOP > TXMAX

1 = condition exists, 0 = normal/OK

D[0] A0

Low transmit optical power alarm,

TXOP < TXMIN

1 = condition exists, 0 = normal/OK

Alarm Status Register 1 (ALARM1)

D[7]

A15

read-only

D[6]

A14

read-only

D[5]

reserved

D[4]

reserved

D[3]

reserved

D[2]

reserved

D[1]

reserved

D[0]

reserved

Default value 0000 0000b = 00h (no events pending)

Serial address A2h

Byte address 113 = 71h

The power-up default value is 00h. Following the first complete A/D conversion cycle, however, either of the bits may be set

depending upon the results.

Bit(s) Function Operation

D[7] A15 High received power (overload) alarm, RXOP > RXMAX 1 = condition exists, 0 = normal/OK

D[6] A14 Low received power (LOS) alarm, RXOP < RXMIN 1 = condition exists, 0 = normal/OK

D[5:0] Reserved Reserved, returns zero on reads

Micrel, Inc. MIC3003

November 2009 51 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Warning Flags

Warning Status Register 0 ( WARN0)

D[7]

read-only

D[6]

read-only

D[5]

read-only

D[4]

read-only

D[3]

read-only

D[2]

read-only

D[1]

read-only

D[0]

read-only

Default value 0000 0000b = 00h (no events pending)

Serial address A2h

Byte address 116 = 74h

The power-up default value is 00h. Following the first complete A/D conversion cycle, however, any of the bits may be set

depending upon the results.

Bit(s) Function Operation

D[7] W7 High temperature warning, TEMP > THIGH 1 = condition exists, 0 = normal/OK

D[6] W6 Low temperature warning, TEMP < TLOW 1 = condition exists, 0 = normal/OK

D[5] W5 High voltage warning, VIN > VHIGH 1 = condition exists, 0 = normal/OK

D[4] W4 Low voltage warning, VIN < VLOW 1 = condition exists, 0 = normal/OK

D[3] W3 High laser diode bias warning, IBIAS > IHIGH 1 = condition exists, 0 = normal/OK

D[2] W2 Low laser diode bias warning, IBIAS < ILOW 1 = condition exists, 0 = normal/OK

D[1] W1

High transmit optical power warning,

TXOP > TXHIGH

1 = condition exists, 0 = normal/OK

D[0] W0

Low transmit optical power warning,

TXOP < TXLOW

1 = condition exists, 0 = normal/OK

Warning Status Register 1 ( WARN1)

D[7]

W15

read-only

D[6]

W14

read-only

D[5]

read-only

D[4]

read-only

D[3]

read-only

D[2]

read-only

D[1]

read-only

D[0]

read-only

Default Value 0000 0000b = 00h (no events pending)

Serial Address A2h

Byte Address 117 = 75h

The power-up default value is 00h. Following the first complete A/D conversion cycle, however, either of the bits may be set

depending upon the results.

Bit(s) Function Operation

D[7] W15 Received power high warning, RXOP > RXHIGH 1 = condition exists, 0 = normal/OK

D[6] W14 Received power low warning, RXOP < RXMIN 1 = condition exists, 0 = normal/OK

D[5:0] Reserved Reserved, returns zero on reads

Micrel, Inc. MIC3003

November 2009 52 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Extended Control and Status (ECNTRL)

D[7]

reserved

D[6]

reserved

D[5]

reserved

D[4]

reserved

D[3]

SRS1

read/write

D[2]

reserved

D[1]

PLOS

read/write

D[0]

PLS

read/write

Default Value 0000 0000b = 00h

Serial Address A2h

Byte Address 118 = 76h

Bit(s) Function Operation

D[7-4] Reserved Reserved—always read as zeros

D[3] SRS1 Soft rate select (RS1) Assert the TRSOUT pin in Rate

Select/Extended Rate Select Emulation

Mode

D[2] Reserved Reserved—always reads as zero

D[1] PLOS Power Level Operation State

D[0] PLS Power Level Select

These two bits are read/write but change

no functionality of the MIC3003

OEM Password Entry (OEMPW)

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for all four bytes 0000 0000b = 00h (reset to zero at power-on)

Serial address A2h

Byte addresses If OEMCFG5-2 = 0: 120 – 123 = 78h – 7Bh

If OEMCFG5-2 = 1: 123 – 126 = 7Bh – 7Eh

This four-byte field is for entry of the password required to access the OEM area of the MIC3003’s memory and registers. A

valid OEM password will also permit access to the user areas of memory. This field is compared to the four-byte OEMPWSET

field at serial address A6h, bytes 12 - 15 (0Ch – 0Fh). If the two fields match, access is allowed to the OEM areas of the

MIC3003 non-volatile memory at serial addresses A4h and A6h. The OEM password is set by writing the new value into

OEMPWSET. The password comparison is performed following the write to the highest address byte of OEMPW, address 7Bh

if OEMCFG5 bit 2 is low, or 7Eh if OEMCFG5 bit 2 is high. This byte must be written last.

A four-byte burst-write sequence to OEMPW may be used as this will result in the highest address byte being written last.

OEMPW is reset to zero at power on. Any values written to OEMPW will be readable by the host regardless of the

locked/unlocked status of the device. If OEMPWSET is set to zero (00000000h), the MIC3003 will remain unlocked regardless

of the contents of the OEMPW field. This is the factory default security setting.

Byte Weight

3 OEM Password Entry, Most Significant Byte (Address = 7Bh resp. 7Eh)

2 OEM Password Entry, 2nd Most Significant Byte (Address = 7Ah resp. 7Dh)

1 OEM Password Entry, 2nd Least Significant Byte (Address = 79h resp. 7Ch)

0 OEM Password Entry, Least Significant Byte (Address = 78h resp. 7Bh)

Micrel, Inc. MIC3003

November 2009 53 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Power-On Hours (POHh and POHl)

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value of both bytes when the

MIC3003 is shipped from the factory

0000 0000b = 00h

Serial address A6h

Bytes addresses MS byte (POHh): 251 = FBh

LS byte (POHl): 252 = FCh

The lower seven bits of POHh contain the most significant bits of the 15-bit power-on hours measurement. The value in POHh

should be combined with the eight-bit power-on hours low byte, POHl, to yield the complete result.

The most significant bit of POHh, POHFLT, is an error flag. If POHFLT is set, the power-on hour meter data has been

corrupted and should be ignored.

It is recommended that a two-byte sequential (block) SMBus read operation be performed on POHh and POHl to insure

coherency between the two registers.

This register is non-volatile and will be maintained through power and reset cycles, including unanticipated power failures.

POHh Bit(s) Function Operation

D[7] Power-on hours fault flag, POHFLT 1 = fault: the power-on hours value is corrupted and cannot

be relied upon

0 = no fault: the power-on hours value is correct

D[6:0] Power-on hours, most significant seven bits

Data Ready Flags (DATARDY)

D[7]

TRDY

read/write

D[6]

VRDY

read/write

D[5]

IRDY

read/write

D[4]

TXRDY

read/write

D[3]

RXDY

read/write

D[2]

reserved

D[1]

reserved

D[0]

reserved

Default value 0000 0000b = 00h

Serial address A6h

Byte address 253 = FDh

When the A/D conversion for a given parameter is completed and the results available to the host, the appropriate data ready

flag will be set. The flag will be cleared when the host reads the corresponding result register.

Bit(s) Function Operation

D[7] TRDY Temperature data ready flag 0 = Result register contains old data; 1 = new data ready

D[6] VRDY Voltage data ready flag 0 = Result register contains old data; 1 = new data ready

D[5] IRDY Bias current data ready flag 0 = Result register contains old data; 1 = new data ready

D[4] TXRDY Transmit power data ready flag 0 = Result register contains old data; 1 = new data ready

D[3] RXRDY Receive power data ready flag 0 = Result register contains old data; 1 = new data ready

D[2:0] Reserved Reserved

Micrel, Inc. MIC3003

November 2009 54 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

User Control Register (USRCTL)

D[7]

Reserved

read/write

D[6]

PORM

read/write

D[5]

PORS

read/write

D[4]

read/write

D[3]

APCSEL

read/write

D[2]

APCSEL

read/write

D[1]

APCSEL

read/write

D[0]

MODSEL

read/write

Default value 0010 0000b = 20h

Serial address A2h

Byte address 254 = FEh

This register provides for control of the nominal APC setpoint and management of interrupts by the end-user. APCSEL[1:0]

select which of the APC setpoint registers, APCSET0, APCSET1, or APCSET2 are used as the nominal automatic power

control setpoint. Similarly, MODSEL[1:0] select which of MODSET0, MODSET1, or MODSET2 are used to select the

modulation level of the laser.

IE must be set for any host interrupts to occur via the /INT pin. If IE is set while /INT is asserted, /INT will be deasserted

immediately.

PORS is always set high by any power-on reset event. If PORM is high, the power-on event will also generate a host interrupt.

PORS will be cleared to zero and the interrupt output deasserted when USRCTL is read by the host.

If PORM is set following the setting of PORS, PORS will remain set, and /INT will be asserted immediately. /INT will not be

deasserted until USRCTL is read by the host.

PORM, IE, APCSEL, and MODSEL are non-volatile and will be maintained through power and reset cycles.

Bit(s) Function Operation

D[7] Reserved Always write as zero; reads undefined.

D[6] PORM Power-on interrupt mask 1 = POR interrupts mask enabled

0 = POR interrupts mask disabled

D[5] PORS Power-on interrupt flag 1 = POR interrupt occurred

0 = No POR interrupt

D[4] IE Global interrupt enable 1 = Host interrupts are enabled

0 = Host interrupts are disabled

D[3:2] APCSEL Selects APC setpoint register 00 = APCSET0

01 = APCSET1

10 = APCSET2

11 = Reserved

D[1:0] MODSEL Selects Modulation setpoint register 00 = MODSET0

01 = MODSET1

10 = MODSET2

11 = Reserved

Micrel, Inc. MIC3003

November 2009 55 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

RESETOUT

D[7]

reserved

read-only

D[6]

reserved

read-only

D[5]

reserved

read-only

D[4]

reserved

read-only

D[3]

reserved

read-only

D[2]

RESETOUT

read/write

D[1]

RESETOUT

read/write

D[0]

RESETOUT

read/write

Default Value 0000 0000b = 00h

Serial address A2h

Byte address 255 = FFh

Bit(s) Function Operation

D[7-3] Reserved Read-only; these bits always return 00000.

D[2:0] RESETOUT

Controls the reset output at pin 17

(QGPO) when Reset mode is

selected (OEMCFG3-7 set to 1)

By default, these three bits are 000, and the QGPO output

is undriven.

If RESET mode is selected in OEMCFG3:

When the three bits are written to 111, QGPO’s open-drain

output will be driven low for 125 μs (typical), after which

QGPO reenters the undriven state.

The RESETOUT field is cleared from 111 to 000 22.5 ms

(typical) after the deassertion edge of QGPO. Other values

of this delay may be selected in the TRSTCLR[2:0] field in

OEMCFG2.

If Reset mode in OEMCFG3 is not selected, these three

bits have no function.

Micrel, Inc. MIC3003

November 2009 56 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

OEM Configuration Register 0 (OEMCFG0)

D[7]

RST

write only

D[6]

QGPOS

read/write

D[5]

DFLT

read-only

D[4]

reserved

D[3]

MODREF

reserved

D[2]

VAUX[2]

read/write

D[1]

VAUX[1]

read/write

D[0]

VAUX[0]

read/write

Default value 0000 0000b = 00h

Serial address A6h

Byte address 00 = 00h

A write to OEMCFG0 will result in any A/D conversion in progress being aborted and the result discarded. The A/D will begin a

new conversion sequence once the write operation is complete.

All bits in OEMCFG0 are non-volatile except DFLT and RST. A valid OEM password is required for access to this register.

Bit(s) Function Operation

D[7] RST 0 = no action; 1 = reset

Issuing a software reset by setting RST high is equivalent to

a full power cycle of the MIC3003.

D[6] QGPOS

Determines the state of QGPO in

GPO mode

If OEMCFG3 bit 7 (QGPOM) is low, this bit determines

whether the QGPO output is high (undriven) or low (driven-

open-drain).

If QGPOM is high (Reset mode), this bit has no function

D[5] DFLT Diode fault flag. 1 = diode fault; 0 = OK.

D[4] OE

Output enable for SHDN, VMOD,

and VBIAS.

1 = enabled; 0 = hi-Z

D[3] MODREF

Selects whether VMOD is

referenced to ground or VDD.

1 = VDD; 0 = GND

D[2:0] VAUX[2:0]

Selects the voltage reported in

VINh:VINl.

000 = VIN

001 = VDDA

010 = VBIAS

011 = VMOD

100 = APCDAC

101 = MODDAC

110 = FLTDAC

Micrel, Inc. MIC3003

November 2009 57 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

OEM Configuration Register 1 (OEMCFG1)

D[7]

INV

read/write

D[6]

GAIN

read/write

D[5]

BIASREF

read/write

D[4]

RFB[2]

read/write

D[3]

RFB[1]

read/write

D[2]

RFB[0]

read/write

D[1]

SRCE

read/write

D[0]

SPOL

read/write

Default value 0000 0010b = 02h

Serial address A6h

Byte address 1 = 01h

A write to OEMCFG1 will result in any A/D conversion in progress being aborted and the result discarded. The A/D will begin a

new conversion sequence once the write operation is complete.

All bits in OEMCFG1 are non-volatile and will be maintained through power and reset cycles. A valid OEM password is

required for access to this register.

Bit(s) Function Operation

D[7] INV Inverts the APC op-amp inputs.

When low, the BIAS DAC output is

connected to the “+”input and FB is

connected to the “–” input of the op

amp. Set low to use the APC

feedback loop.

0 = emitter follower (no inversion);

1 = common emitter (inverted); read/write; non-volatile.

D[6] GAIN

Sets the feedback voltage range by

changing the APCDAC output

swing; 0-VREF for optical feedback,

0-VREF/4 for electrical feedback.

1 = VREF/4 full scale;

0 = VREF full scale

D[5] BIASREF

Selects whether FB and VMPD are

referenced to ground or VDD and

selects feedback resistor termination

voltage (VDDA or GNDA).

1 = VDD; 0 = GNDA

If this bit is set to 0, bit 1 should be set to 1

If this bit is set to 1, bit 1 should be set to 0

D[4:2] RFB[2:0]

Selects internal feedback resistance.

Resistors will be terminated to VDDA

or GNDA according to BIASREF.

000 = ∞

001 = 800 Ω

010 = 1.6kΩ

011 = 3.2kΩ

100 = 6.4kΩ

101 = 12.8kΩ

110 = 25.6kΩ

111 = 51.2kΩ

D[1] SRCE

VBIAS source or sink drive. 1 = source (NPN): bit 5 should be set to 0.

0 = sink (PNP): bit 5 should be set to 1.

D[0] SPOL

Polarity of the shutdown output,

SHDN, when active.

1 = SHDN is active-high

0 = SHDN is active-low

Micrel, Inc. MIC3003

November 2009 58 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

OEM Configuration Register 2 (OEMCFG2)

D[7]

SMBADR[3]

read/write

D[6]

SMBADR[2]

read/write

D[5]

SMBADR[1]

read/write

D[4]

SMBADR[0]

read/write

D[3]

read/write

D[2]

TRSTCLR[2]

read/write

D[1]

TRSTCLR[1]

read/write

D[0]

TRSTCLR[0]

read/write

Default value 1010 0010b = xxh (device address = 1010 xxxxb)

This value is the basis for using A0 h, A2 h, A4 h, and A6 h as the names of

the different device address spaces of the MIC3003.

Serial address A6h

Byte address 2 = 02h

Caution: Changes to SMBADR take effect immediately. Any accesses following a write to SMBADR must be to the newly

programmed serial bus address.

A valid OEM password is required for access to this register. This register is non-volatile and will be maintained through power

and reset cycles.

Bit(s) Function Operation

D[7:4] SMBADR[3:0]

Most significant four bits of the

serial bus device address

Writes take effect immediately.

D[3:0] TRSTCLR[2:0]

Set the delay between QGPO and

the clearing of RESETOUT

These three bits set the delay between the deassertion

edge of the QGPO output in Reset mode and the

subsequent clearing of the three RESETOUT bits in the

RESETOUT Register:

000: Zero delay

001: 17.5 ms typical

010: 22.5 ms typical (default)

011: 27.0 ms typical

100: 45 ms typical

Minimum and maximum values may be found by adding

tolerances of -10% and +10% to the above values.

If Reset mode is not selected, these bits have no function.

Micrel, Inc. MIC3003

November 2009 59 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

APC Setpoint 0, 1, and 2 (APCSET0, APCSET1, APCSET2)

Automatic Power Control Setpoint

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for all three bytes 0000 0000b = 00h

Serial address A6h

Byte addresses APCSET0: 3 = 03h

APCSET1: 4 = 04h

APCSET2: 5 = 05h

When the APC is on, the eight-bit signed integer compensation value corresponding to the current temperature is taken from

the BIASLUT look-up table, added to the selected APCSET (0, 1, or 2) register and loaded into the VBIAS DAC.

If DAC Calibration mode is selected in OEMCAL0, a write to any one of the three APCSETn registers will cause the VBIAS DAC

to be updated immediately. DAC Calibration mode disables the output of the BIASLUT lookup table, so the unmodified

APCSETn register value propagates directly to the DAC.

The eight-bit value presented to the VBIAS DAC is always available for readback in the APCDAC register.

A valid OEM password is required for access to these registers. These registers are non-volatile and will be maintained through

power and reset cycles.

Modulation Setpoint 0, 1, and 2 (MODSET0, MODSET1, and MODSET2)

Nominal VMOD Setpoint

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for all three bytes 0000 0000b = 00h

Serial address A6h

Byte address MODSET0: 6 = 06h

MODSET1: 30 = 1Eh

MODSET2: 31 = 1Fh

When the APC is on, the eight-bit signed integer compensation value corresponding to the current temperature is taken from

the MODLUT look-up table, added to the selected MODSET (0, 1, or 2) register and loaded into the VMOD DAC.

If DAC Calibration mode is selected in OEMCAL0, a write to any one of the three MODSETn registers will cause the VMOD DAC

to be updated immediately. DAC Calibration mode disables the output of the MODLUT lookup table, so the unmodified

MODSETn register value propagates directly to the DAC.

The eight-bit value presented to the VMOD DAC is always available for readback in the MODDAC register.

A valid OEM password is required for access to these registers. These registers are non-volatile and will be maintained through

power and reset cycles.

Micrel, Inc. MIC3003

November 2009 60 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

IBIAS Fault Threshold (IBFLT)

Bias Current Fault Threshold

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value 0000 0000b = 00h

Serial address A6h

Byte address 7 = 07h

When the Fault Comparator is running, the eight-bit signed integer compensation value corresponding to the current

temperature is taken from the IFTLUT look-up table, added to IBFLT, and used for comparison with the laser bias current value

for fault generation. Faults are generated if the bias current value exceeds the compensated (LUT offset) IBFLT register

contents.

If DAC Calibration mode is selected in OEMCAL0, the output of the IFTLUT lookup table is disabled, so the unmodified IBFLT

A valid OEM password is required for access to these registers. These registers are non-volatile and will be maintained through

power and reset cycles.

Transmit Power Fault Threshold (TXFLT)

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value 0000 0000b = 00h

Serial address A6h

Byte address 8 = 08h

When the Fault Comparator is running the TXFLT register value is used for comparison with the transmit power value for fault

generation. Faults are generated if the transmit power exceeds the TXFLT register contents.

A valid OEM password is required for access to this register. This register is non-volatile and will be maintained through power

and reset cycles.

Loss-Of-Signal Threshold (LOSFLT)

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value 0000 0000b = 00h

Serial address A6h

Byte address 9 = 09h

When the Fault Comparator is running, a fault is generated if the received power is lower than the LOSFLT value set in this

A valid OEM password is required for access to this register. This register is non-volatile and will be maintained through power

and reset cycles.

Micrel, Inc. MIC3003

November 2009 61 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Fault Suppression Timer (FLTTMR)

Fault Suppression Inter val in Increments of 0.5 ms

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value 0000 0000b = 00h

Serial address A6h

Byte address 10 = 0Ah

Saturation faults are suppressed for a time, tFLTTMR, following laser turn-on. This avoids nuisance tripping while the APC loop

starts up. The length of this interval is (FLTTMR x 0.5 ms), typical. A value of zero will result in no fault suppression.

A valid OEM password is required for access to this register. This register is non-volatile and will be maintained through power

and reset cycles.

Fault Mask (FLTMSK)

D[7]

OEMIM

read/write

D[6]

POHE

read/write

D[5]

reserved

D[4]

reserved

D[3]

SATMSK

read/write

D[2]

TXMSK

read/write

D[1]

IAMSK

read/write

D[0]

DFMSK

read/write

Default value 0000 0000b = 00h

Serial address A6h

Byte address 11 = 0Bh

A valid OEM password is required for access to this register. This register is non-volatile and will be maintained through power

and reset cycles.

Bit Function Operation

D[7] OEMIM OEM interrupt mask 1 = Interrupts are masked

0 = Interrupts are enabled

This bit is similar to the IE (Global Interrupt Enable) bit in the

User Control Register. The /INT output can only be asserted

if IE is high and OEMIM is low.

D[6] POHE OEM Power-on Hour Meter enable 1 = Power-on Hour Meter enabled

0 = Power-on Hour Meter disabled

D[5:4] D[5:4] Reserved Always write as zero; reads undefined

D[3] SATMSK APC saturation fault mask 1 = masked; 0 = enabled

D[2] TXMSK High TX optical power fault mask 1 = masked; 0 = enabled

D[1] IAMSK High bias current high fault mask 1 = masked; 0 = enabled

D[0] DFMSK Diode fault mask 1 = masked; 0 = enabled

Micrel, Inc. MIC3003

November 2009 62 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

OEM Password Setting (OEMPWSET)

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value for all bytes 0000 0000b = 00h

Serial address A6h

Byte addresses 12 - 15 = 0Ch - 0Fh

This four-byte field is the password required for access to the OEM area of the MIC3003’s memory and registers. This field is

compared to the four-byte OEMPW field at serial address A2h. If the two fields match, access is allowed to the OEM areas of

the MIC3003 non-volatile memory at serial addresses A4h and A6h.

The OEM password may be set by writing the new value into OEMPWSET. The new password will not take effect until after a

power-on reset occurs or a warm reset is performed using the RST bit in OEMCFG0. This allows the new password to be

verified before it takes effect.

These registers are non-volatile and will be maintained through power and reset cycles. A valid OEM password is required for

access to this register.

Byte Weight

3 OEM Password, Most Significant Byte

2 OEM Password, 2nd Most Significant Byte

1 OEM Password, 2nd Least Significant Byte

0 OEM Password, Least Significant Byte

OEM Calibration 0 (OEMCAL0)

D[7]

reserved

read-only

D[6]

FLTDIS

read/write

D[5]

FSPIN

read/write

D[4]

WRINH

read/write

D[3]

APCCAL

read/write

D[2]

reserved

read-only

D[1]

reserved

read-only

D[0]

FRCOPS

read/write

Default value 0000 0000b = 00h

Serial address A6h

Byte address 16 = 10h

A valid OEM password is required for access to this register. This register is volatile and will not keep its value through power

cycles.

Micrel, Inc. MIC3003

November 2009 63 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Bit Function Operation

D[7] Reserved Always write as zero; reads undefined.

D[6] FLTDIS Fault Comparator disable 0 = Fault Comparator faults enabled

1 = Fault Comparator faults disabled

When FLTDIS is high, the Fault Comparator does not run,

and the following faults are not detected:

• High IBIAS faults

• High transmit power faults

• Low receive power faults

If a fault condition was detected prior to the assertion of

FLTDIS, the fault flag will remain active until cleared, but

cannot be set again until the Fault Comparator is allowed

to run.

D[5] FSPIN

Fault Comparator “spin-on-channel” mode

select; do not enable ADC and FC spin-

on-channel modes simultaneously.

0 = Normal Fault Comparator operation

1 = Force the Fault Comparator to spin on one channel

When the Fault Comparator spins on just one channel

(selected via OEMCAL1[1:0]), the two channels not being

examined will not, of course, respond to fault conditions.

D[4] WRINH Inhibit NVRAM write cycles. 0 = Normal NVRAM operation

1 = Inhibit NVRAM writes

When WRINH is high, writes to the MIC3003’s internal

memory do not occur. Registers that are non-volatile are

written with the new value, but will not retain that value

through a power cycle, since the NVRAM backing storage

has not been modified.

D[3] APCCAL

Selects APC DAC calibration mode -

DACs may be controlled directly.

0 = Normal mode

1 = DAC calibration mode.

When DAC calibration mode is enabled, the temperature

compensation lookup tables are disabled, so the DACs

are presented with the values written into their

corresponding registers.

D[2:1] Reserved Always write as zeros; reads undefined.

D[0] FRCOPS

Forces outputs for board-level or system-

level testing

0 = Normal operation

1 = Force outputs for testing: The following outputs are

driven to their active states:

• TXFAULT (active polarity set in OEMCFG5)

• /INT (only driven if the OEMIM bit is clear in

FLTMSK)

• RXLOS (active polarity and RXLOS selection are

set in OEMCFG6)

Micrel, Inc. MIC3003

November 2009 64 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

OEM Calibration 1 (OEMCAL1)

D[7]

reserved

read-only

D[6]

ADSTP

read/write

D[5]

ADIDL

read-only

D[4]

ONESHOT

read/write

D[3]

ADSPIN

read/write

D[2]

SPIN[2]

read/write

D[1]

SPIN[1]

read/write

D[0]

SPIN[0]

read/write

Default value 0000 0000b = 00h

Serial address A6h

Byte address 17 = 11h

A valid OEM password is required for access to this register. This register is volatile and will not keep its value through power

cycles.

Bit Function Operation

D[7] Reserved Always write as zero; reads undefined.

D[6] ADSTP

Stop ADC: Halts the analog to digital

converter

0 = ADC in normal operation

1 = ADC stopped

When ADSTP is set, the five-channel ADC halts and no

new ADC results are computed. Existing result registers

are not changed.

In addition, no new temperature compensation is applied

to the APC loop and fault parameters, and no

comparisons of the ADC results against the alarm and

warning limits is performed.

D[5] ADIDL ADC idle flag 0 = ADC is busy

1 = ADC is idle

ADIDL may be used in conjunction with ONESHOT to

determine when the single ADC conversion is complete.

After ONESHOT is set, the ADC runs until completion

and then halts. Software may poll ADIDL to detect this

completion before interrofating the result.

D[4] ONESHOT Triggers one-shot A/D conversion cycle 0 = Normal ADC operation

1 = ADC one-shot mode

Setting ONESHOT high starts the ADC and causes it to

stop after the next conversion is complete. After the

conversion, the ADC remains stopped until ONESHOT is

set low.

Multiple single ADC conversions may be executed by

repeatedly writing one to ONESHOT.

D[3] ADSPIN

Selects ADC spin-on-channel mode; do

not enable ADC and FC spin-on-channel

modes simultaneously

0 = Normal ADC operation

1 = ADC spin-on-channel

D[2:0] SPIN[2:0]

ADC and Fault Comparator (FC) channel

select for spin-on-channel mode; do not

enable ADC and FC spin-on-channel

modes simultaneously

ADC:

000 = temperature

001 = voltage

010 = VILD

011 = VMPD

100 = VRX

Micrel, Inc. MIC3003

November 2009 65 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

LUT Index (LUTINDX)

D[7]

read-only

D[6]

read-only

D[5]

read-only

D[4]

read-only

D[3]

read-only

D[2]

read-only

D[1]

read-only

D[0]

read-only

Default value (before the first set of 16

temperature measurements has been

accumulated)

0000 0000b = 00h

Serial address A6h

Byte address 18 = 12h

The look-up table index is derived from the current temperature measurement as follows:

INDEX = TAVG / 2

where TAVG is the current average temperature, averaged over a set of 16 samples. This register allows the current table index

to be read by the host. The appropriate table base address must be added to LUTINDX to form a complete table index in

physical memory.

A valid OEM password is required for access to this register.

Micrel, Inc. MIC3003

November 2009 66 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

OEM Configuration 3 (OEMCFG3)

D[7]

QGPOM

read/write

D[6]

TXFPOL

read/write

D[5]

GPOD

read/write

D[4]

GPOM

read/write

D[3]

GPOC

read/write

D[2]

TXFINM

read/write

D[1]

LOSDIS

read/write

D[0]

INTCAL

read/write

Default value 0000 1000b = 08h

Serial address A6h

Byte address 19 = 13h

This register is non-volatile and will be maintained through power and reset cycles. A valid OEM password is required for access

to this register.

Bit Function Operation

D[7] QGPOM QGPO pin function select 0: GPO (general purpose output)

1: Reset output

D[6] TXFPOL

TXFIN active polarity select; a fault is

indicated when TXFIN = TXFPOL

0 = The TXFIN input is active-low

1 = The TXFIN input is active-high

This bit is ignored if TXFINM = 0

D[5] GPOD GPO output drive 0 = GPO output is open-drain

1 = GPO output is push-pull

This bit is ignored if GPOM = 0

D[4] GPOM GPO/RRSOUT pin mode select 0 = RRSOUT output

1 = GPO output

D[3] GPOC GPO output control 0 = Set the GPO pin low

1 = Set the GPO pin high

This bit is ignored if GPOM = 0

D[2] TXFINM SHDN/TXFIN pin mode select 0 = SHDN output

1 = TXFIN input

D[1] LOSDIS RXLOS comparator and output disable 0 = RXLOS fault enabled, and the RXLOS output is enabled

for normal operation

1 = RXLOS fault disabled; also, the RXLOS output is

disabled, and will remain low

D[0] INTCAL Calibration mode select 0 = External calibration mode

1 = Internal calibration.(the MIC3003’s ALU applies slope

and offset coefficients to the ALU results as necessary)

BIAS DAC Setting (APCDAC)

Current VBIAS Setting

D[7]

read-only

D[6]

read-only

D[5]

read-only

D[4]

read-only

D[3]

read-only

D[2]

read-only

D[1]

read-only

D[0]

read-only

Default value 0000 0000b = 00h

Serial address A6h

Byte address 20 = 14h

This register reflects (reads back) the value being sent to the BIAS DAC (APCSET0, APCSET1, or APCSET2 whichever is

selected, with temperature compensation applied).

A valid OEM password is required for access to this register.

Micrel, Inc. MIC3003

November 2009 67 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Modulation DAC Setting (MODDAC)

Current VMOD Setting

D[7]

read-only

D[6]

read-only

D[5]

read-only

D[4]

read-only

D[3]

read-only

D[2]

read-only

D[1]

read-only

D[0]

read-only

Default value 0000 0000b = 00h

Serial address A6h

Byte address 21 = 15h

This register reflects (reads back) the value set in the being sent to the modulation DAC (MODSET0, MODSET1, or MODSET2

whichever is selected, with temperature compensation applied).

A valid OEM password is required for access to this register.

OEM Readback Register (OEMRD)

D[7]

Reserved

read-only

D[6]

KILL_LASER

read-only

D[5]

RXP_FLT

Read-only

D[4]

INT

read-only

D[3]

APCSAT

read-only

D[2]

IBFLT

read-only

D[1]

TXFLT

read-only

D[0]

RRSOUT

read-only

Default value 0000 0000b = 00h

Serial address A6h

Byte address 22 = 16h

This register reflects (reads back) the status of the bits corresponding to the parameters defined below.

A valid OEM password is required for access to this register.

Bit Function Operation

D[7] Reserved Always reads as a zero

D[6] KILL_LASER

State of the internal laser disable

signal

0: The MIC3003 is disabling the laser

1: The laser is enabled to operate

D[5] RXP_FLT

Registered Fault Comparator

detection of a receive power

fault

0: No Fault Comparator receive power fault

1: The Fault Comparator has detected a receive power fault

D[4] INT

Mirrors state of /INT but active-

high

1 = The interrupt is asserted

0 = No pending interrupt.

D[3] APCSAT Registered APC saturation fault 1 = APC saturation fault detected

0 = Normal operation.

D[2] IBFLT

Registered Fault Comparator

detection of an IBIAS fault

1 = IBIAS fault detected

0 = Normal operation

D[1] TXFLT

Registered Fault Comparator

detection of a transmit power

fault

1 = Registered transmit power fault

0 = normal operation

D[0] TRSOUT

State of the rate select output

pin, TRSOUT

1 = high; 0 = low

Micrel, Inc. MIC3003

November 2009 68 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Signal Detect Threshold (LOSFLTn)

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value 0000 0000b = 00h

Serial address A6h

Byte address 23 = 17h

This eight-bit register works in conjunction with the LOSFLT register to provide hysteresis and control the operation of the loss of

signal comparator. The comparator’s output, RXLOS, is asserted when the input on VRX falls below the level in LOSFLT. The

output will then be deasserted when the VRX signal rises above the level in LOSFLTn.

The input signal is subject to scaling by the RXPOT. If the LOS comparator is disabled, i.e., LOSDIS = 1, this register is ignored.

A valid OEM password is required for access to this register. This register is non-volatile and will be maintained through power

and reset cycles.

RX EEPOT Tap Selection (RXPOT)

D[7]

reserved

read-only

D[6]

reserved

read-only

D[5]

reserved

read-only

D[4]

RXPOT[4]

read/write

D[3]

RXPOT[3]

read/write

D[2]

RXPOT[2]

read/write

D[1]

RXPOT[1]

read/write

D[0]

RXPOT[0]

read/write

Default value 0000 0000b = 00h

Serial address A6h

Byte address 24 = 18h

This register is non-volatile and will be maintained through power and reset cycles. A valid OEM password is required for access

to these registers.

Bit(s) Function Operation

D[7:5] Reserved Reserved. Always write as zero; reads return zeros.

D[4:0] RXPOT tap selection:

Adjust gain of the receive power measurement:

00000 = No divider action

00001 = 31/32

00010 = 30/32

•

11110 = 2/32

11111 = 1/32

Micrel, Inc. MIC3003

November 2009 69 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

OEM Configuration 4 (OEMCFG4)

D[7]

TXF_WRN

read/write

D[6]

TXF_ALM

read/write

D[5]

LAT_WRN

read/write

D[4]

LAT_ALM

read/write

D[3]

ISTART[3]

read/write

D[2]

ISTART[2]

read/write

D[1]

ISTART[1]

read/write

D[0]

ISTART[0]

read/write

Default value 0000 0000b = 00h

Serial address A6h

Byte address 25 = 19h

This register is non-volatile and will be maintained through power and reset cycles. A valid OEM password is required for

access to these registers.

Bit(s) Function Operation

D[7] TXF_WRN

Allows warnings to assert

TXFAULT

0: Warnings do not assert TXFAULT

1: Warnings assert TXFAULT

The RXPWR low warning flag does not assert TXFAULT

D[6] TXF_ALM

Allows alarms to assert

TXFAULT

0: Alarms do not assert TXFAULT

1: Alarms assert TXFAULT

The RXPWR low alarm flag does not assert TXFAULT

D[5] LAT_WRN Warning latch

0: Warnings flags are latched. They are cleared by reading

the register or toggling TXDISABLE.

1: Warnings flags are not latched., i.e. they are set and reset

with the warning condition. The flags are also cleared by

reading the register or toggling TXDISABLE.

D[4] LAT_ALM Alarm latch

0: Alarms flags are latched. They are cleared by reading the

1: Alarms flags are not latched., i.e. they are set and reset

with alarm condition. The flags are also cleared by reading

the register or toggling TXDISABLE.

D[3:0] ISTART[3:0]

ISTART current level selection. ISTART current level selection:

0000 = No ISTART current

0001 - 1111 = 0.375 mA x ISTART[[3:0]

ISTART is used to speed up the laser start-up after a fault

occurs. The charging current of the compensation capacitor

starts from ISTART instead of ramping up from 0.

Micrel, Inc. MIC3003

November 2009 70 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

OEM Configuration 5 (OEMCFG5)

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value 0000 0000b = 00h

Serial address A6h

Byte address 26 = 1Ah

This register is non-volatile and will be maintained through power and reset cycles. A valid OEM password is required for access

to these registers.

Bit(s) Function Operation

D[7] SHDN output enable / disable 0: SHDN is enabled. TXFAULT will trigger the SHDN output

1: SHDN is disabled. TXFAULT has no effect on the SHDN output

This applies when pin 7 is set as the SHDN output

D[6] Lookup table temperature

offset control

0: The temperature result used for the LUT access averaging algorithm does

not have the offset coefficient applied

1: The temperature result used for the LUT access averaging algorithm is

offset by the signed 6-bit (.5 C resolution) offset coefficient.

D[5] Temperature result register

offset control

0: The temperature result register does not have the offset coefficient applied

1: The temperature result register is offset by the signed 6-bit (.5 C resolution)

offset coefficient.

D[4] Polarity of TXFAULT

0: TXFAULT is active-high

1: TXFAULT is active-low

D[3] SMBus multipart support

0: Multipart mode off

1: Multipart mode on

D[2] OEM password location

0: A6h: 120-123 (78h-7Bh)

1: A6h: 123-126 (7Bh-7Eh)

D[1] SMBUS timeout enable /

disable

0: SMBUS timeout enabled

1: SMBUS timeout disabled

Micrel, Inc. MIC3003

November 2009 71 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

OEM Configuration 6 (OEMCFG6)

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default value 0000 0000b = 00h

Serial address A6h

Byte address 27 = 1Bh

This register is non-volatile and will be maintained through power and reset cycles. A valid OEM password is required for access

to these registers.

Bit(s) Function Operation

D[7] A0h space access control 0: A0h space is used according to SFF-8472

1: A0h space does not respond to any access request. SMBus transactions to

A0h receive a NACK response.

D[6:5] RXPWR Linearization Intervals 00: Temperature-based coefficient selection

01: Programmable delimiters

10: Hard coded delimiters

11: Reserved

Options 01 and 10 partition the receive power result range into eight regions,

each of which has its own slope and offset coefficients. The delimiters identify

the region boundaries within the 12-bit receive power range of results, and

may be either hard-coded (10) or programmable (01).

Use of hard-coded delimiters frees up exta A6 memory space for scratchpad

use.

D[4] TXDISABLE debounce enable

/ disable

0: TXDISABLE is not debounced

1: TXDISABLE is debounced. Glitches less than 5 ms are rejected.

Set this bit to 1 if a mechanical switch is used for TXDISABLE. Set to 0 for

normal operation to assure compliance to the SFP MSA.

D[3] RXLOS Polarity

0: The RXLOS output is low for normal operation and high with a loss of signal

condition.

1: The RXLOS output is high for normal operation (signal detected) and low

with a loss of signal (no signal detected) condition.

D[2] RXLOS/TRSOUT Select 0: RXLOS is selected for output

1: TRRSOUT is selected for output

D[1] Temperature resolution

0: Temperature is measured to a resolution of 1 ºC (eight-bit resolution)

1: Temperature is measured to a resolution of 0.5 ºC (nine-bit resolution)

D[0] TXFAULT clear mode

0: TXFAULT remains set until TXDISABLE is toggled

1: TXFAULT is in continuous mode and follows the state of the faults

In continuous mode, the fault conditions asserting TXFAULT are not registered

and turn on and off According to the MIC3003’s operation.

Micrel, Inc. MIC3003

November 2009 72 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Power-On Hour Meter Data (POHD AT A)

D[7]

read/write

D[6]

read/write

D[5]

read/write

D[4]

read/write

D[3]

read/write

D[2]

read/write

D[1]

read/write

D[0]

read/write

Default values for all bytes when the MIC3003

is shipped

0000 0000b = 00h

Serial address A6h

Byte addresses 32 – 34 and 36 - 38 = 20h - 22h and 24h - 26h

These registers are used for backing up the POH result during power cycles. At power-up, the POH meter selects the larger of

the two values as the initial count. Incremental results are stored in alternate register pairs. The power-on hour meter may be

reset or preset by writing to these registers.

These registers are not typically intended to be used by the OEM or end user. The current value of the power-on hours meter

may be read from the POHh and POHl registers.

If it is necessary to preset the power-on hours meter to a specific value, please consult the factory for the exact format to be

written to the POHDATA registers.

These registers are non-volatile and will be maintained through power and reset cycles. A valid OEM password is required for

access to these registers.

Byte Weight

3 POHA, high-byte

2 POHA, low-byte

1 POHB, high-byte

0 POHB, low-byte

OEM Scratchpad Registers (SCRATCHn)

Default value 0000 0000b = 00h

Serial address A6h

Byte addresses 136 - 207 (88 - CFh)

208 - 221 (D0 - DDh): This area is part of the OEM scratch pad only if the hard-

coded delimiters option for receive power linearization is used.

222 - 250 (DE - FAh)

The scratchpad registers are general-purpose non-volatile memory locations. They can be freely read from and written to any

time the MIC3003 is in OEM mode.

Micrel, Inc. MIC3003

November 2009 73 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

RX Power Coefficient Look-up Table (RXLUTn)

Default values Offset coefficients are set to a default value of zero

Slope coefficients are set to a default vakue of 1.0

Serial address A6h

Byte addresses 40 - 71 = 28h - 47h

These registers hold the receive power slope and offset coefficients used to calibrate the MIC3003’s ADC receive power result

in internal calibration mode.

These registers are non-volatile and will be maintained through power and reset cycles. A valid OEM password is required for

access to these registers.

A6 Address Bytes Definition

40 (28h) RXSLP0h RX slope 0, high byte

41 (29h) RXSLP0l RX slope 0, low byte

42 (2Ah) RXOFF0h RX offset 0, high byte

43 (2Bh) RXOFF0l RX offset 0, low byte

44 (2Ch) RXSLP1h RX slope 1, high byte

45 (2Dh) RXSLP1l RX slope 1, low byte

46 (2Eh) RXOFF1h RX offset 1, high byte

47 (2Fh) RXOFF1l RX offset 1, low byte

• •

68 (44h) RXSLP7h RX slope 7, high byte

69 (45h) RXSLP7l RX slope 7, low byte

70 (46h) RXOFF7h RX offset 7, high byte

71 (47h) RXOFF7l RX offset 7, low byte

Calibration Constants (CALCOEFn)

Default values Offset coefficients are set to a default value of zero

Slope coefficients are set to a default vakue of 1.0

Serial address A6h

Byte addresses 74 - 87 = 4Ah - 57h

These registers hold the slope and offset coefficients used to calibrate the MIC3003’s ADC results in internal calibration mode.

Note that the temperature offset is also used in external calibration mode; but this can be disabled in OEMCFG5 (or by setting

the offset coefficient to zero).

These registers are non-volatile and will be maintained through power and reset cycles. A valid OEM password is required for

access to these registers.

Micrel, Inc. MIC3003

November 2009 74 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Address Bytes Definition

74 (4Ah) TOFFh Temperature offset (six-bit signed offset, .5 C resolution)

75 (4Bh) TOFF0l Not used

76 (4Ch) VSLP0h Voltage slope, high byte

77 (4Dh) VSLP0l Voltage slope, low byte

78 (4Eh) VOFFh Voltage offset, high byte

79 (4Fh) VOFF0l Voltage offset, low byte

80 (50h) ISLP0h Bias current slope, high byte

81 (51h) ISLP0l Bias current slope, low byte

82 (52h) IOFFh Bias current offset, high byte

83 (53h) IOFF0l Bias current offset, low byte

84 (54h) TXSLPh TX Power slope, high byte

85 (55h) TXSLPl TX Power slope, low byte

86 (56h) TXOFFh TX Power offset, high byte

87 (57h) TXOFFl TX Power offset, low byte

Manufacturer ID Register (MFG_ID)

Identifies Micrel as the manufacturer of th e device. Always returns 2Ah

D[7]

read-only

D[6]

read-only

D[5]

read-only

D[4]

read-only

D[3]

read-only

D[2]

read-only

D[1]

read-only

D[0]

read-only

Default value 0010 1010b = 2Ah

Serial address A6h

Byte address 254 = FEh

The value in this register, in combination with the DEV_ID register, serves to identify the MIC3003 and its revision number to

software.

This register is read-only.

Bit(s) Function Operation

D[7:0] Identifies Micrel as the manufacturer of the device. Always

returns 2Ah.

Read-only. Always returns Ah

Device ID Register (DEV_ID)

D[7]

read-only

D[6]

read-only

D[5]

read-only

D[4]

read-only

D[3]

read-only

D[2]

read-only

D[1]

read-only

D[0]

read-only

MIC3003 Device ID

always reads 0 at D[7-6] and 11 at D[5-4]

Die Revision

Default value 0011 XXXXb = 3Xh

Serial address A6h

Byte address 255 = FFh

The value in this register, in combination with the MFG_ID register, serve to identify the MIC3003 and its revision number to

software. This register is read-only.

Micrel, Inc. MIC3003

November 2009 75 M9999-111209-C

hbwhelp@micrel.com or (408) 955-1690

Package Information

24-Pin MLF® (MLF-24)

MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA

TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com

The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its

use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.

Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product

can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical

implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user.

A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to

fully indemnify Micrel for any damages resulting from such use or sale.

Incor

orated.

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Micrel:

MIC3003GML MIC3003GML TR MIC3003GML-TR