SURFACE MOUNT DISPLAY Part Number: KCDA03-106 Super Bright Orange Features Description z 0.3 inch digit height. The Super Bright Orange device is made with AlGaInP (on z Low current operation. GaAs substrate) light emitting diode chip. z Excellent character appearance. z Mechanically rugged. z Package :300pcs / reel. z Gray face, white segment. z Moisture sensitivity level : level 2a. z RoHS compliant. Package Dimensions& Internal Circuit Diagram SEK Notes: 1. All dimensions are in millimeters (inches), Tolerance is 0.25(0.01")unless otherwise noted. 2. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 3.The gap between the reflector and PCB shall not exceed 0.25mm. SPEC NO: DSAG1703 REV NO: V.9A DATE: APR/07/2013 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Y.Liu ERP: 1352000309 Selection Guide Part No. Dice KCDA03-106 Iv (ucd) [1] @ 10mA Lens Type Super Bright Orange (AlGaInP) Description Min. Typ. 21000 46000 *5600 *11000 White Diffused Common Anode, Rt. Hand Decimal. Note: 1. Luminous intensity/ luminous Flux: +/-15%. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25C Symbol Parameter Device Typ. peak Peak Wavelength Super Bright Orange D [1] Dominant Wavelength 1/2 Max. Units Test Conditions 610 nm IF=20mA Super Bright Orange 601 nm IF=20mA Spectral Line Half-width Super Bright Orange 29 nm IF=20mA C Capacitance Super Bright Orange 15 pF VF=0V;f=1MHz VF [2] Forward Voltage Super Bright Orange 2.1 2.5 V IF=20mA IR Reverse Current Super Bright Orange 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at TA=25C Parameter Super Bright Orange Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 195 mA 5 V Reverse Voltage Operating / Storage Temperature -40C To +85C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAG1703 REV NO: V.9A DATE: APR/07/2013 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Y.Liu ERP: 1352000309 Super Bright Orange KCDA03-106 SPEC NO: DSAG1703 REV NO: V.9A DATE: APR/07/2013 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Y.Liu ERP: 1352000309 KCDA03-106 Recommended Soldering Pattern (Units : mm; Tolerance: 0.15) Reel Dimension Tape Specifications (Units : mm) SPEC NO: DSAG1703 REV NO: V.9A DATE: APR/07/2013 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Y.Liu ERP: 1352000309 PACKING & LABEL SPECIFICATIONS KCDA03-106 Detailed application notes are listed on our website. http://www.kingbright.com/application_notes SPEC NO: DSAG1703 REV NO: V.9A DATE: APR/07/2013 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Y.Liu ERP: 1352000309