ALUMINUM ELECTROLYTIC CAPACITORS
138
Chip Type, Low Impedance.
Chip type, low impedance temperature range up to +105°C.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU) .
Specifications
Category
Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Endurance
Shelf Life
Resistance to soldering
heat
Performance CharacteristicsItem
–55 to +105°C
25 to 35V
220 to 1000µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV (µA).
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds,
which is maintained at 250°C. The capacitors shall meet
the characteristic requirements listed at right when they
are removed from the plate and restored to 20°C.
Capacitance change
Leakage current
tan δ
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Capacitance change
Leakage current
tan δ
Within ±30% of the initial capacitance value
Less than or equal to the initial specified value
200% or less than the initial specified value
Measurement frequency : 120Hz at 20°C
Rated voltage (V)
tan δ (MAX.)
25
0.14
35
0.12
Measurement frequency : 120Hz
Z–25°C / Z+20°C
Rated voltage (V)
Impedance ratio
ZT / Z20 (MAX.)
25
2
3
3
35
2
3
3
Marking Black print on the case top.
UCV
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
Code
V
E
25
V
35
Voltage
Type numbering system (Example : 35V 220µF)
U
1
C
2
V
3
1
4
V
5
2
6
2
7
1
8
M
9
C
10
L
11
1
12
G
13
S
14
Configuration
Size code
Capacitance tolerance (±20%)
Rated capacitance (220µF)
Rated voltage (35V)
Series name
Type
(φ 6.3)
Voltage (V:35V)
Capacitance
Series
A2
220V
CV
Plastic platform
0.3MAX.
L±0.3
φD±0.5
A±0.2 A±0.2
B±0.2
C±0.2
0.5MAX.
E
H
Positive
Negative
(φ 8,φ10) Plastic platform
0.3MAX.
L±0.5
φD±0.5
A±0.2 A±0.2
B±0.2
C±0.2
0.5MAX.
E
H
Positive
Negative
Lot No.
Lot No.
Capacitance
Series
Trade mark
Voltage (V : 35V)
A2
680V
CV
Taping code
6.3 CL
8・10 NL
CodeφD
Standard
6.3×7.7
A
B
C
E
2.4
6.6
6.6
2.2
8×10
2.9
8.3
8.3
3.1
10×10
3.2
10.3
10.3
4.5
L7.7 10 10
H
0.5to0.8 0.8to1.1 0.8to1.1
(mm)
φ
D×L
MAX.Impedance(Ω)at20℃100kHz,
Ratedripplecurrent(mArms)at105℃100kHz
Pressure relief vent
Chip Type Type numbering system (Example : 35V 220
µ
F)
Frequency coefficient of rated ripple current
0 Frequency0/
Coefficient
50Hz 120Hz 300Hz 1kHz 10kHz or more
0.35 0.50 0.64 0.83 1.00
Dimensions
Code
V25
1E
35
1V
220
330
470
560
680
820
1000
221
331
471
561
681
821
102
Rated
ripple
Impedance
×
0.16 600
6.3 × 7.7
0.08 850
8 × 10
0.06 1190
10 × 10
0.16 600
6.3 × 7.7
0.08 850
8 × 10
0.06 1190
10 × 10
UCV
UCM
Smaller
Higher capacitance
Code
V
E
25
V
35
Rated Voltage
Type numbering system (Example : 35V 220µF)
U
1
C
2
V
3
1
4
V
5
2
6
2
7
1
8
M
9
C
10
L
11
1
12
G
13
S
14
Configuration
Size code
Capacitance tolerance (±20%)
Rated capacitance (220µF)
Rated voltage (35V)
Series name
Type
(φ 6.3)
Voltage (C:35V)
Capacitance
Series
A2
220V
CV
Plastic platform
0.3MAX.
L±0.3
φD±0.5
A±0.2 A±0.2
B±0.2
C±0.2
0.5MAX.
E
H
Positive
Negative
(φ 8 to φ10, φ10) Plastic platform
0.3MAX.
L±0.5
φD±0.5
A±0.2 A±0.2
B±0.2
C±0.2
0.5MAX.
E
H
Positive
Negative
Lot No.
Lot No.
Capacitance
Series
Trade mark
Voltage (V : 35V)
A2
680V
CV
Taping code
6.3 CL
8・10 NL
Codeφd
Standard
6.3×7.7
A
B
C
E
2.4
6.6
6.6
2.2
8×10
2.9
8.3
8.3
3.1
10×10
3.2
10.3
10.3
4.5
L7.7 10 10
H
0.5to0.8 0.8to1.1 0.8to1.1
(mm)
φ
D×L
MAX.Impedance(Ω)at20℃100kHz,
Ratedripplecurrent(mArms)at105℃100kHz
Pressure relief vent
Z–40°C / Z+20°C
Z–55°C / Z+20°C
