1
2
notice_e-01
Notice for TAIYO YUDEN products
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2011. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully be-
fore practical application or usage of the Products.
Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorpo-
rating such products, which are caused under the conditions other than those specified in this catalog or individual
specification.
■ Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is
available.
■ Please conduct validation and verification of products in actual condition of mounting and operating environment
before commercial shipment of the equipment.
■ All electronic components or functional modules listed in this catalog are developed, designed and intended for
use in general electronics equipment.(for AV, office automation, household, office supply, information service,
telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any
equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal,
disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have
direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance.
Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, subma-
rine system, military, etc. where higher safety and reliability are especially required.
In addition, even electronic components or functional modules that are used for the general electronic equipment,
if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliabil-
ity evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to
install a protective circuit is strongly recommended at customer's design stage.
■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distribu-
tors (so called “TAIYO YUDEN’s official sales channel”).
It is only applicable to the products purchased from any of TAIYO YUDEN’ s official sales channel.
■ Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may oc-
cur in connection with a third party's intellectual property rights and other related rights arising from your usage of
products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights.
■ Caution for export
Certain items in this catalog may require specific procedures for export according to “Foreign Exchange and For-
eign Trade Control Law” of Japan, “U.S. Export Administration Regulations”, and other applicable regulations.
Should you have any question or inquiry on this matter, please contact our sales staff.
152
1
2
■ FEATURES
■ ORDERING CODE
■ EXTERNAL DIMENSIONS/MINIMUM QUANTITY
■ APPLICATIONS
■ IMPEDANCE-FREQUENCY CHARACTERISTICS
Measured by HP4291A
Please contact TAIYO YUDEN for further information in regard to other characteristics.
FL05RD / FL05R TYPE FL06BT TYPE
■ OPERATING TEMP.
filter01_e-01
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
◦ Use of high loss ferrite materials for excellent high frequency noise
absorption.
◦ High impedance for normal mode applications.
◦ 05 RD type available in taping for automatic insertion.
◦ 06 BT type is designed for high current applications (3A).
◦ Absorption of high frequency noise from digital equipment data lines.
LEADED NORMAL MODE CHOKE COILS FOR DC AND SIGNAL LINES
【FL-R / RD Type】
【FL-BT Type】
❶Type
FL Wound torroids
and beads
❶Type
FL Wound torroids and beads
❸Shape
R△Ring core,
with single wire lead
RD Ring core,
with case, pin type
△＝Blank space
❹Product classification code
△04
△＝Blank space
❹Nominal inductance
(μH)
example
1R0 1.0
200 20.0
※R＝decimal point
❺Inductance tolerance
A Higher than normal value
E Special tolerance
❼Internal code
△Standard product
07 Product classification
code
△＝Blank space
❺Internal code
△Standard product
△＝Blank space
❻Packaging
△Bulk
T Tape & Reel
Z Ammo
ーSpecial code
△＝Blank space
❸Shape
BT Cylinder,
porous core
❷Dimensions of core
05 4.8mm
❷Dimensions of core
(diameter)
06 6.0mm
F L 0 5 R D 2 0 0 A T ○
❶ ❷ ❸ ❹ ❺ ❻ ❼
F L 0 6 B T △0 4 ○
❶❷❸ ❹❺
Type 〔05RD〕 〔05R〕 〔06BT04〕
Fig.
Minimum
Quantity
(pcs.)
Bulk 400 500 250
Tape & Reel 2000 ー ー
Ammo 1500 ー ー
Unit : mm (inch)
＋0.6
ー0.2
9.0max
（0.35max）
3.7max
（0.146max）
φ0.6
（φ0.024）
9.0max
（0.351max）
4.0±1
（0.157±0.039）
5.0
（0.197 ）
＋0.024
ー0.008
6.5max
（0.256max）
3.0max
（0.118max）
φ0.3
（φ0.012）
φ6.0±0.2
（φ0.24±0.008）
15.2max
（0.598max）
WAV E
◦ ー25℃～105℃（Including self-generated heat）
153
1
2
NOISE SUPPRESSION COMPONENTS
／
FERRITE BEAD INDUCTORS
■ PART NUMBERS
filter01_e-01
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Impedance
〔Ω〕 (typical)
DC Resistance
〔Ω〕 (max)
Rated current
〔A〕 (max)
FL05RD 1R0E□RoHS 1.0＋1.0
－0.5 800 (at 400MHz) 0.08 0.5
FL05R 100A RoHS 10 min. 900 (at 200MHz) 0.05
1.5
FL05RD 100A□RoHS
FL05R 200A－07 RoHS 20 min. 2000 (at 100MHz) 0.08
FL05RD 200A□RoHS
FL06BT 04 RoHS ー 1000 (at 150MHz) 0.05 3.0
□Please specify the packaging code (T : Tape & reel, Z : ammo, Blank space : bulk)
1
2
filter01_pack-P1 filter01_pack_e-01
■ PACKAGING
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
◦FL05RD
①Minimum Quantity
Type Minimum Quantity (pcs.)
Bulk Tape & Reel Ammo
FL05R 500 ー ー
FL05RD 400 2000 1500
FL06BT 250 ー ー
②Taping dimensions
Type Symbol Dimension
FL05RD
D1 9.0 max. (0.354 max.)
H2 9.0 max. (0.354 max.)
T 3.7 max. (0.146 max.)
H1 31.0 max. (1.22 max.)
H 18.0±1.0 (0.709±0.039)
P 12.7±1.0 (0.500±0.039)
P0 12.7±0.3 (0.500±0.012) ※1
P1 3.85±0.8 (0.152±0.031)
P2 6.35±1.3 (0.250±0.051)
W1 9.0＋0.75
ー0.5 (0.354＋0.030
ー0.020)
F 5.0＋0.6
ー0.2 (0.197＋0.024
ー0.008)
d φ0.6 (φ0.024)
△h 0±2.0 (0±0.079)
W 18.0＋1.0
ー0.5 (0.709＋0.024
ー0.008)
W0 12.5 min. (0.492 min.)
W2 3.0 min. (0.118 min.) ※2
ℓ 0 max. (0 max.)
D0 4.0±0.3 (0.157±0.012)
L 11.0 max. (0.433 max.)
t 0.7±0.2 (0.028±0.008)
◦FL05RD
③Reel size
60 or less〔53〕
（2.362 or less〔2.087〕）
Unit : mm (inch)
Dimensions in parenthesis are measured value.
※1 Accumulated error for 20 pitches shall be within ±2mm.
※2 Pasting tape shall not exceed paste board.
Unit : mm (inch)
1
2
le0104fi01_reli-RP1 le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
1. Operating temperature Range
LA Type
ー25～＋105℃CAL45 Type
LHL□□□
FBA/FBR ー25～＋85℃
FL05□ Type ー25～＋105℃
FL06BT Type
【Test Method and Remarks】
LA・CA・FL : Including self-generated heat
LHL□□□ : Including self-generated heat
3. Rated current
LA Type
Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : The maximum DC value having inductance within 10% and temperature incease within 40℃ (LA:20℃) by the application of DC bias.
LHL□□□ : The maximum DC value having inductance decrease within 10% (LHLC08, LHLC10：within 30%) and temperature increase within the following specified
temperature by the application of DC bias.
Reference temperature : 25℃ (LHL08, LHL10, LHL13)
: 30℃ (LHL16, LHLP□□)
: 40℃ (LHLC08, LHLC10)
FB : No disconnection or appearance abnormality by continuous current application for 30 min. Change after the application shall be within ±20% of the initial value.
This is not guaranteed for electrial characteristics during current application.
FL : The maximum DC value having temperature rise within specified value.
5. Inductance
LA Type
Within the specified toleranceCAL45 Type
LHL□□□
FBA/FBR
FL05□ Type Within the specified tolerance
FL06BT Type
【Test Method and Remarks】
LA, CA : Measuring equipment : LCR meter (HP4285A + HP42851A or its equivalent)
Measuring frequency : Specified frequency
LHL□□□ : Measuring equipment : LCR meter (HP4285A＋HP42851A or its equivalent)
LCR meter (HP4263A) or its equivalent (at 1kHz)
Measuring frequency : Specified frequency
FL05R□ : Measuring equipment : HP4262A or its equivalent
Measuring frequency : 1kHz
6. Q
LA Type Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Measuring equipment : LCR meter (HP4285A + HP42851A or its equivalent)
Measuring frequency : Specified frequency
LHL□□□ (except LHLP) : Measuring equipment : LCR meter (HP4285A＋HP42851A or its equivalent)
LCR meter (HP4263A) or its equivalent (at 1kHz)
Measuring frequency : Specified frequency
2. Storage temperature Range
LA Type
ー40～＋85℃
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
4. Impedance
LA Type
CAL45 Type
LHL□□□
FBA/FBR Within the specified tolerance
FL05□ Type
FL06BT Type Refer to individual specification
【Test Method and Remarks】
FB : Measuring equipment : Impedance analyzer (HP4191A) or its equivalent
Measuring frequency : Specified frequency
FL06BT : Measuring equipment : 4291A (HP) or its equivalent
Measuring frequency : Specified frequency
1
2
le0104fi01_reli-RP2
le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
11. Over current
LA Type No emission of smoke no firing.
CAL45 Type
LHL□□□ There shall be no scorch or short of wire.
LHLC08,LHLC10 : There shall be no firing.
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LHL□□□/LA・CAL45 Type： Measuring current : Rated current×2
Duration : 5 min.
Number of measuring : one time
8. Self resonance frequency
LA Type Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Measuring equipment : Network analyzer (Anritsu MS620J or its equivalent)
LHL□□□ (except LHLP) : Measuring equipment : (HP4191A, 4192A) its equivalent
9. Temperature characteristic
LA Type △L/L : Within ±5%
CAL45 Type
LHL□□□ △L/L : Within ±7% (except LHLP16 : Within ±20%)
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Change of maximum inductance deviation in step 1 to 5
Step Temperature (℃)
1 20
2ー25 (Minimum operating temperature)
3 20 (Standard temperature)
4＋85 (Maximum operating temperature)
5 20
LHL□□□ : Change of maximum inductance deviation in step 1 to 5
Temperature at step 1 : 20℃
Temperature at step 2 : Minimum operating temperature
Temperature at step 3 : 20℃ (Standard temperature)
Temperature at step 4 : Maximum operating temperature
Temperature at step 5 : 20℃
10. Tensile strength test
LA Type
No abnormality such as cut lead, or looseness.CAL45 Type
LHL□□□
FBA/FBR No abnormality such as cut lead, or looseness.
FL05□ Type No abnormality such as cut lead, or looseness.
FL06BT Type
【Test Method and Remarks】
LA : Apply the stated tensile force progressively in the direction to draw terminal.
force (N) duration (s)
25 5
CA : Apply the stated tensile force progressively in the direction to draw terminal.
force (N) duration (s)
10 10
LHL□□□ : Apply the stated tensile force progressively in the direction to draw terminal.
Nominal wire diameter tensile φd (mm) force (N) duration (s)
0.3＜φd≦0.5 5
30±50.5＜φd≦0.8 10
0.8＜φd≦1.2 25
FBA/FBR : The body of a component shall be fixed and a tensile force of 20±1N shall be applied to the lead wire in the axial diretion of the component during 10±1 seconds.
FL05R□ : Fix the body of a component in the direction to draw terminal,and gradually apply the tensile force of 4.9N.
7. DC Resisitance
LA Type
Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Measuring equipment : low ohmmeter (A&D AD5812 or its equivalent)
LHL□□□・FB・FL : Measuring equipment : DC ohmmeter
1
2
le0104fi01_reli-RP3 le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
12. Terminal strength : bending
LA Type
No abnormality such as cut lead, or looseness.
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation
is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter tensile
φd (mm)
Bending force
(N)
Mass reference weight
(kg)
0.3＜φd≦0.5 2.5 0.25
0.5＜φd≦0.8 5 0.50
LH・FB : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation
is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter tensile
φd (mm)
Bending force
(N)
Mass reference weight
(kg)
0.3＜φd≦0.5 2.5 0.25
0.5＜φd≦0.8 5 0.5
0.8＜φd≦1.2 10 1.0
13. Insulation resisitance : between the terminals and body
LA Type
CAL45 Type
LHL□□□ 100MΩ min.
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LHL□□□ : Applied voltage : 500 VDC
Duration : 60 sec.
14. Insulation resistance : between terminals and core
LA Type
CAL45 Type
LHL□□□
FBA/FBR 1MΩ min. (Other than materail code MA)
FL05□ Type
FL06BT Type
【Test Method and Remarks】
FBA・FBR : Applied voltage : 100 VDC
Duration : 60±5 sec.
15. Withstanding : between the terminals and body
LA Type
CAL45 Type
LHL□□□ No abnormality such as insulation damage
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LHL□□□ : Accoding to JIS C5102. 7. 1. 3 (C)
Metal global method
Applied voltage : 500 VDC
Duration : 60 sec.
16. DC bias characteristic
LA Type △L/L : Within ー10%
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Measure inductance with appliation of rated current using LCR meter to compare it with the initial value.
17. Body strength
LA Type No abnormality as damage.
CAL45 Type
LHL□□□
FBA/FBR No abnormality such as cracks on body.
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Applied force : 30N
Duration : 10 sec.
Speed : Shall attain to specified force in 2 sec.
CAL45 : Applied force : 50N
Duration : 10 sec.
Speed : Shall attain to specified force in 2 sec.
FBA : Applied force : 50±3N
Duration : 30±1 sec.
1
2
le0104fi01_reli-RP4
le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
18. Resisitance to vibration
LA Type △L/L : Within ±5% Q : 30min
CAL45 Type △L/L : Within ±5%
LHL□□□ Appearance : No abnomality △L/L : Within ±5% Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR Appearance : No abnomality Impedance change : Within ±20%
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Directions : 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range : 10 to 55 to 10Hz (1min.)
Amplitude : 1.5mm
Mounting method : Soldering onto printed board.
Recovery : At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs.
LHL□□□・FB ： Directions : 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range : 10 to 55 to 10Hz (1min.)
Amplitude : 1.5mm (But don't exceed acceleration 196m/s2 (two power))
Mounting method : Soldering onto printed board.
19. Resistance to shock
LA Type No significant abnormality in appearance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Drop test
Impact material : concrete or vinyl tile
Height : 1m
Total number of drops : 10 times
20. Solderability
LA Type At least 75％ of terminal electrode is covered by new solder.
CAL45 Type
LHL□□□ At least 75％ of terminal electrode is covered by new solder.
FBA/FBR At least 90％ of terminal electrode is covered by new solder.
FL05□ Type At least 75％ of terminal electrode is covered by new solder.
FL06BT Type
【Test Method and Remarks】
LA, CA : Solder temperature : 230±5℃
Duration : 2±0.5 sec.
LHL□□□ : Solder temperature : 235±5℃
Duration : 2±0.5 sec.
Immersion depth : Up to 1.5mm from bottom of case.
FB : Solder temperature : 230±5℃
Duration : 3±1 sec.
Immersion depth : Up to 1.5mm from terminal root.
FL05R□ : Solder temperature : 230±5℃
Duration : 2±0.5 sec.
Immersion depth : Up to 2 to 2.5mm from terminal root.
FL06BT : Solder temperature : 230±5℃
Duration : 3±1 sec.
Immersion depth : Up to 0.5 to 1.0mm from terminal root.
21. Resisitance to soldering heat
LA Type No significant abnormality in appearance
CAL45 Type △L/L : Within ±5%
LHL□□□ No significant abnormality in appearance Inductance change : Within ±5% Q change : Within ±30%(LHLP : only △L/L)
FBA/FBR No significant abnormality in appearance Impedance change : Within ±20%
FL05□ Type Refer to individual specification
FL06BT Type No significant abnormality in appearance Impedance change : Within ±20%
【Test Method and Remarks】
LA, CA : Solder temperature : (CA) 270±5℃, (LA) 260±5℃
Duration : 5±0.5 sec. One time
Immersed conditions : Inserted into substrate with t=1.6mm
Recovery : At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs.
LHL□□□ : Solder bath method : Solder temperature : 260±5℃
Duration : 10±1 sec.
Up to 1.5mm from the bottom of case.
Manual soldering : Solder temperature : 350±10℃ (At the tip of soldering iron)
Duration : 5±1 sec.
Up to 1.5mm from the bottom of case.
Caution : No excessive pressing shall be applied to terminals.
Recovery : 4 to 24hrs of recovery under the standard condition after the test.
FB : Solder bath method : Condition 1 : Solder temperature : 260±5℃
Duration : 10±1 sec.
Immersion depth : Up to 1.5mm from the terminal root.
Condition 2 : Solder temperature : 350±5℃
Duration : 3±1 sec.
Immersion depth : Up to 1.5mm from the terminal root.
Recovery : 3hrs of recovery under the standard condition after the test.
FL : Solder condition : 260±5℃ 10±1 sec.
Immersion depth : Up to 0.5 to 1.0mm from the terminal root.
Recovery : 3hrs of recovery under the standard condition after the test.
1
2
le0104fi01_reli-RP5 le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
22. Resisitance to solvent
LA Type Please avoid the ultrasonic cleaning of this product.
CAL45 Type
LHL□□□
FBA/FBR No significant abnormality in appearance Impedance change : Within ±20%
FL05□ Type
FL06BT Type
【Test Method and Remarks】
FB : Solvent temperature : 20～25℃
Duration : 30±5 sec.
Solvent type : Acetone
Recovery : 3hrs of recovery under the standard condition after the test.
23. Thermal shock
LA Type △L/L : Within ±10% Q : 30min
CAL45 Type △L/L : Within ±10%
LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP：only △L/L)
FBA/FBR Appearance : No abnormality Impedance change : Within ±20%
FL05□ Type Refer to individual specification
FL06BT Type Appearance : No abnormality Impedance change : Within ±20%
【Test Method and Remarks】
LA, CA : Conditions for 1cycle
Step Temperature (℃) Duration (min.)
1ー25＋0
ー330±3
2 Room temperature Within 3
3＋85＋2
ー030±3
4 Room temperature Within 3
Number of cycles : 5 cycles
Recovery : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs.
LHL□□□・FB : Accoding to JIS C0025
Conditions for 1 cycle
Step Temperature (℃) Duration (min.)
1 Minimum operating temperature＋0
ー330±3
2 Room temperature Within 3
3 Minimum operating temperature＋2
ー030±3
4 Room temperature Within 3
Number of cycles : 10 cycles 〔LHL□□□〕
: 5 cycles (FBA, FBR)
Recovery : 4 to 24hrs of recovery under the standard condition after the removal from the test chamber. 〔LHL□□□〕
: 3hrs of recovery under the standard condition after the removal from the test chamber. (FBA, FBR)
FL : Accoding to JIS C0025
Conditions for 1 cycle
Step Temperature (℃) Duration (min.)
1ー25＋0
ー330±3
2 Room temperature Within 3
3＋85＋2
ー030±3
4 Room temperature Within 3
Number of cycles : 10 cycles
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
24. Damp heat
LA Type △L/L : Within ±10% Q : 30min
CAL45 Type △L/L : Within ±10%
LHL□□□
FBA/FBR Appearance：No abnormality Impedance change：Within ±20%
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Temperature : 40±2℃
Humidity : 90～95%RH
Duration : 1000 hrs
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
FB : Temperature : 60±2℃
Humidity : 90～95%RH
Duration : 1000 hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
1
2
le0104fi01_reli-RP6
le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
25. Loading under damp heat
LA Type △L/L : Within ±10% Q : 30min
CAL45 Type △L/L : Within ±10%
LHL□□□ Appearance : No abnormality Imductance change : Within ±10% Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
FL05□ Type Refer to individual specification
FL06BT Type Appearance : No abnormality Impedance change : Within ±20%
【Test Method and Remarks】
LA, CA : Temperature : 40±2℃
Humidity : 90～95%RH
Duration : 1000 hrs
Applied current : Rated current
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
LHL□□□ : Temperature : 40±2℃
Humidity : 90～95%RH
Duration : 1000±24 hrs
Applied current : Rated current
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL : Temperature : 60±3℃
Humidity : 90～95%RH
Duration : 500 (＋12, ー0) hrs
Applied current : Rated current
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
26. Loading at high temperature
LA Type △L/L : Within ±10% Q : 30min
CAL45 Type △L/L : Within ±10%
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Temperature : 85±2℃
Duration : 1000 hrs
Applied current : Rated current
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
27. Low temperature life test
LA Type △L/L : Within ±10% Q : 30min
CAL45 Type △L/L : Within ±10%
LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
FL05□ Type Refer to individual specification
FL06BT Type Appearance : No abnormality Impedance change : Within ±20%
【Test Method and Remarks】
LA, CA : Temperature : ー25±2℃
Duration : 1000 hrs
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
LHL□□□ : Temperature : ー40±3℃
Duration : 1000±24 hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL : Temperature : ー40±3℃
Duration : 500 (＋12, ー0) hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
28. High temperature life test
LA Type
CAL45 Type
LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
FL05□ Type Refer to individual specification
FL06BT Type Appearance : No abnormality Impedance change : Within ±20%
【Test Method and Remarks】
LHL□□□ : Temperature : 105±3℃
Duration : 1000±24 hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL : Temperature : 85±3℃
Duration : 500 (＋12, ー0) hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
1
2
le0104fi01_reli-RP7 le0104fi01_reli_e-01
■ PRECAUTIONS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
1. Circuit Design
Precautions
◆Operating environment
1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems,
measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high
reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where
product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2. PCB Design
Precautions ◆Design
1. Please design insertion pitches as matching to that of leads of the component on PCBs.
Technical
consider-
ations
◆Design
1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of
the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs.
3. Considerations for automatic placement
Precautions
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
Technical
consider-
ations
◆Adjustment of mounting machine
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4. Soldering
Precautions
◆Wave soldering
1. Please refer to the specifications in the catalog for a wave soldering.
2. Do not immerse the entire inductor in the flux during the soldering operation.
◆Lead free soldering
1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, soldering etc
sufficiently.
Recommended conditions for using a soldering iron:
・Put the soldering iron on the land-pattern.
・Soldering iron's temperature - Below 350℃
・Duration - 3 seconds or less
・The soldering iron should not directly touch the inductor.
◆Reflow soldering
1. As for reflow soldering, please contact our sales staff.
Technical
consider-
ations
◆Lead free soldering
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of
the products.
5. Cleaning
Precautions
◆Cleaning conditions
1. CAL type, LH type, LA Type
Please do not do cleaning by a supersonic wave.
Technical
consider-
ations
◆Cleaning conditions
1. CAL type, LH type, LA Type
If washing by supersonic waves, supersonic waves may deform products.
6. Handling
Precautions
◆Handling
1. Keep the inductors away from all magnets and magnetic objects.
◆Mechanical considerations
1. Please do not give the inductors any excessive mechanical shocks.
2. LH type
If inductors are dropped onto the floor or a hard surface they should not be used.
◆Packing
1. Please do not give the inductors any excessive mechanical shocks.
In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item).
Technical
consider-
ations
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Mechanical considerations
1. There is a case to be damaged by a mechanical shock.
2. LH type
There is a case to be broken by a fall.
◆Packing
1. There is a case that a lead wire could be deformed by a fall or an excessive shock.
7. Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should
be controlled.
Recommended conditions
・Ambient temperature 0～40℃
・Humidity Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes.
For this reason, inductors should be used within one year from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Technical
consider-
ations
◆Storage
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of
taping/packaging materials may take place.
CAL Type, LH Type, FB Type, FL Type, LA Type
