Product Folder Sample & Buy Support & Community Tools & Software Technical Documents LM61 SNIS121J - JUNE 1999 - REVISED NOVEMBER 2016 LM61 2.7-V, SOT-23 or TO-92 Temperature Sensor 1 Features 3 Description * * The LM61 device is a precision, integrated-circuit temperature sensor that can sense a -30C to 100C temperature range while operating from a single 2.7V supply. The output voltage of the LM61 is linearly proportional to temperature (10 mV/C) and has a DC offset of 600 mV. The offset allows reading negative temperatures without the need for a negative supply. The nominal output voltage of the LM61 ranges from 300 mV to 1600 mV for a -30C to 100C temperature range. The LM61 is calibrated to provide accuracies of 2C at room temperature and 3C over the full -25C to 85C temperature range. 1 * * * * * * * * * * Calibrated Linear Scale Factor of 10 mV/C Rated for Full Temperature Range (-30 to 100C) Suitable for Remote Applications UL Recognized Component 2C or 3C Accuracy at 25C (Maximum) 3C Accuracy for -25C to 85C (Maximum) 4C Accuracy for -30C to 100C (Maximum) 10 mV/C Temperature Slope (Maximum) 2.7-V to 10-V Power Supply Voltage Range 125-A Current Drain at 25C (Maximum) 0.8C Nonlinearity (Maximum) 800- Output Impedance (Maximum) 2 Applications * * * * * * * * * Cellular Phones Computers Power Supply Modules Battery Management FAX Machines Printers HVAC Disk Drives Appliances The linear output of the LM61, 600-mV offset, and factory calibration simplify external circuitry required in a single supply environment where reading negative temperatures is required. Because the quiescent current is less than 125 A, self-heating is limited to a very low 0.2C in still air. Shutdown capability for the LM61 is intrinsic because its inherent low power consumption allows it to be powered directly from the output of many logic gates. Device Information(1) PART NUMBER PACKAGE LM61 BODY SIZE (NOM) SOT-23 (3) 1.30 mm x 2.92 mm TO-92 (3) 4.30 mm x 4.30 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. Key Specifications Typical Application VALUE Accuracy at 25C 2C or 3C Accuracy for -25C to 85C 3C Accuracy for -30C to 100C 4C Temperature slope 10 mV/C Power supply voltage 2.7 V to 10 V Current drain at 25C 125 A Nonlinearity 0.8C Output impedance 800 VO = (10 mV/C x TC) + 600 mV 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LM61 SNIS121J - JUNE 1999 - REVISED NOVEMBER 2016 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 3 6.1 6.2 6.3 6.4 6.5 6.6 3 3 3 4 4 5 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics........................................... Typical Characteristics .............................................. Detailed Description .............................................. 7 7.1 7.2 7.3 7.4 Overview ................................................................... Functional Block Diagram ......................................... Feature Description................................................... Device Functional Modes.......................................... 7 7 7 7 8 Application and Implementation .......................... 8 8.1 Application Information.............................................. 8 8.2 Typical Applications .................................................. 8 9 Power Supply Recommendations...................... 11 10 Layout................................................................... 11 10.1 Layout Guidelines ................................................. 11 10.2 Layout Examples................................................... 11 10.3 Thermal Considerations ........................................ 12 11 Device and Documentation Support ................. 14 11.1 11.2 11.3 11.4 11.5 11.6 Related Documentation......................................... Receiving Notification of Documentation Updates Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 14 14 14 14 14 14 12 Mechanical, Packaging, and Orderable Information ........................................................... 14 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision I (February 2013) to Revision J Page * Added Device Information table, Device Comparison Table, Pin Configuration and Functions section, Specifications section, ESD Ratings table, Detailed Description section, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section ...................................................................................................................... 1 * Added Thermal Information table ........................................................................................................................................... 4 * Changed RJA values for DBZ (SOT-23) From: 450C/W To: 286.3C/W and for LP (TO-92) From: 180C/W To: 162.2C/W .............................................................................................................................................................................. 4 Changes from Revision H (February 2013) to Revision I * 2 Page Changed layout of National Semiconductor Data Sheet to TI format .................................................................................... 1 Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM61 LM61 www.ti.com SNIS121J - JUNE 1999 - REVISED NOVEMBER 2016 5 Pin Configuration and Functions DBZ Package 3-Pin SOT-23 Top View LP Package 3-Pin TO-92 Pin Functions PIN NAME TYPE NO. DESCRIPTION +VS 1 Power Positive power supply pin. VOUT 2 Output Temperature sensor analog output. GND 3 Ground Device ground pin, connected to power supply negative terminal. 6 Specifications 6.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) MIN MAX UNIT Supply voltage 12 -0.2 V Output voltage (+VS + 0.6) -0.6 V 10 mA Output current Input current at any pin (2) Maximum junction temperature, TJ Storage temperature, Tstg (1) (2) -65 5 mA 125 C 150 C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. When the input voltage (VI) at any pin exceeds power supplies (VI < GND or VI > VS), the current at that pin must be limited to 5 mA. 6.2 ESD Ratings VALUE V(ESD) (1) (2) (3) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) (2) 2500 Machine Model (MM) (3) 250 UNIT V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. The human body model is a 100-pF capacitor discharged through a 1.5-k resistor into each pin. The machine model is a 200-pF capacitor discharged directly into each pin. 6.3 Recommended Operating Conditions +VS Supply voltage T Operating temperature MIN MAX 2 10 LM61C -30 100 LM61B -25 85 Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM61 UNIT V C 3 LM61 SNIS121J - JUNE 1999 - REVISED NOVEMBER 2016 www.ti.com 6.4 Thermal Information LM61 THERMAL METRIC (1) DBZ (SOT-23) LP (TO-92) 3 PINS 3 PINS UNIT 286.3 162.2 C/W RJA Junction-to-ambient thermal resistance (2) RJC(top) Junction-to-case (top) thermal resistance 96 85 C/W RJB Junction-to-board thermal resistance 57.1 -- C/W JT Junction-to-top characterization parameter 5.3 29.2 C/W JB Junction-to-board characterization parameter 55.8 141.4 C/W (1) (2) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report. The junction-to-ambient thermal resistance is specified without a heat sink in still air. 6.5 Electrical Characteristics +VS = 3 V (DC) (1) (2) PARAMETER TEST CONDITIONS TA = 25C Accuracy (5) MIN (3) Sensor gain (average slope) Output impedance -2 2 LM61C -3 3 LM61B -3 3 LM61C -4 -0.6 0.6 LM61C -0.8 0.8 LM61B 9.7 10 10.3 LM61C 9.6 10 10.4 +VS = 3 V to 10 V 0.8 TA = -30C to 85C, +VS = 2.7 V 2.3 4 5 mV/V +VS = 2.7 V to 3.3 V -5.7 5.7 mV +VS = 2.7 V to 10 V (8) k 0.7 TA = 25C Temperature coefficient of quiescent current (7) mV/C -0.7 Change of quiescent current (6) C +VS = 3 V to 10 V +VS = 2.7 V to 10 V (1) (2) (3) (4) (5) C mV LM61B Quiescent current Long term stability (8) UNIT 4 600 TA = 85C to 100C, +VS = 2.7 V Line regulation (7) MAX (3) LM61B Output voltage at 0C Nonlinearity (6) TYP (4) TJ = TMAX = 100C, for 1000 hours 82 125 155 A 5 A 0.2 A/C 0.2 C Limits are specified to TI's AOQL (Average Outgoing Quality Level). Typical limits represent most likely parametric norm. Maximum and minimum limits apply for TA = TJ = TMIN to TMAX. Typical limits apply for TA = TJ = 25C. Accuracy is defined as the error between the output voltage and 10 mV/C multiplied by the device's case temperature plus 600 mV, at specified conditions of voltage, current, and temperature (expressed in C). Nonlinearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the device's rated temperature range. Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating effects can be computed by multiplying the internal dissipation by the thermal resistance. For best long-term stability, any precision circuit gives best results if the unit is aged at a warm temperature, or temperature cycled for at least 46 hours before long-term life test begins. This is especially true when a small (Surface-Mount) part is wave-soldered; allow time for stress relaxation to occur. The majority of the drift occurs in the first 1000 hours at elevated temperatures. The drift after 1000 hours does not continue at the first 1000-hour rate. Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM61 LM61 www.ti.com SNIS121J - JUNE 1999 - REVISED NOVEMBER 2016 6.6 Typical Characteristics The LM61 in the SOT-23 package mounted to a printed-circuit board as shown in Figure 18 was used to generate the following thermal curves. Figure 1. Junction-to-Ambient Thermal Resistance Figure 2. Thermal Time Constant Figure 3. Thermal Response in Still Air with Heat Sink Figure 4. Thermal Response in Stirred Oil Bath with Heat Sink Figure 5. Thermal Response in Still Air without Heat Sink Figure 6. Quiescent Current vs Temperature Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM61 5 LM61 SNIS121J - JUNE 1999 - REVISED NOVEMBER 2016 www.ti.com Typical Characteristics (continued) The LM61 in the SOT-23 package mounted to a printed-circuit board as shown in Figure 18 was used to generate the following thermal curves. Figure 7. Accuracy vs Temperature Figure 8. Noise Voltage +VS 2 V/Div 0V 0.2 V/Div VO 0V 5 s/Div Figure 9. Supply Voltage vs Supply Current Figure 10. Start-Up Response 6 Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM61 LM61 www.ti.com SNIS121J - JUNE 1999 - REVISED NOVEMBER 2016 7 Detailed Description 7.1 Overview The LM61 is a precision integrated-circuit temperature sensor that can sense a -30C to 100C temperature range using a single positive supply. The output voltage of the LM61 has a positive temperature slope of 10 mV/C. A 600-mV offset is included, enabling negative temperature sensing when biased by a single supply. The temperature-sensing element is comprised of a delta-VBE architecture. The temperature-sensing element is then buffered by an amplifier and provided to the VOUT pin. The amplifier has a simple class A output stage as shown in Functional Block Diagram. 7.2 Functional Block Diagram 7.3 Feature Description 7.3.1 LM61 Transfer Function The LM61 follows a simple linear transfer function to achieve the accuracy as listed in Electrical Characteristics. Use Equation 1 to calculate the value of VO. VO = 10 mV/C x TC + 600 mV where * * T is the temperature in C VO is the LM61 output voltage (1) 7.4 Device Functional Modes The only functional mode of the LM61 device is an analog output directly proportional to temperature. Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM61 7 LM61 SNIS121J - JUNE 1999 - REVISED NOVEMBER 2016 www.ti.com 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information The LM61 has a wide supply range and a 10-mV/C output slope with a 600-mV DC. Therefore, it can be easily applied in many temperature-sensing applications where a single supply is required for positive and negative temperatures. 8.2 Typical Applications 8.2.1 Typical Temperature Sensing Circuit VO = 10 mV/C x TC + 600 mV Figure 11. Typical Temperature Sensing Circuit Diagram 8.2.1.1 Design Requirements For this design example, use the parameters listed in Table 1 as the input parameters. Table 1. Design Parameters 8 PARAMETER VALUE Power supply voltage 2.7 V to 3.3 V Accuracy at 25C 2C (maximum) Accuracy over -25C to 85C 3C (maximum) Temperature slope 10 mV/C Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM61 LM61 www.ti.com SNIS121J - JUNE 1999 - REVISED NOVEMBER 2016 8.2.1.2 Detailed Design Procedure The LM61 is a simple temperature sensor that provides an analog output. Therefore, design requirements related to layout outweigh other requirements in importance. See Layout for more information. 8.2.1.2.1 Capacitive Loads The LM61 handles capacitive loading well. Without any special precautions, the LM61 can drive any capacitive load as shown in Figure 12. Over the specified temperature range the LM61 has a maximum output impedance of 5 k. In an extremely noisy environment it may be necessary to add some filtering to minimize noise pickup. It is recommended that 0.1-F capacitor be added between +VS and GND to bypass the power-supply voltage, as shown in Figure 13. In a noisy environment it may be necessary to add a capacitor from VOUT to ground. A 1-F output capacitor with the 5-k maximum output impedance forms a 32-Hz lowpass filter. Because the thermal time constant of the LM61 is much slower than the 5-ms time constant formed by the RC, the overall response time of the LM61 is not significantly affected. For much larger capacitors this additional time lag increases the overall response time of the LM61. Figure 12. LM61 No Decoupling Required for Capacitive Load Figure 13. LM61 with Filter for Noisy Environments Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM61 9 LM61 SNIS121J - JUNE 1999 - REVISED NOVEMBER 2016 www.ti.com 8.2.1.3 Application Curve Figure 14. Accuracy vs Temperature 8.2.2 Other Application Circuits Figure 15 shows an application circuit example using the LM61 device. Customers must fully validate and test any circuit before implementing a design based on an example in this section. Unless otherwise noted, the design procedures in Typical Temperature Sensing Circuit are applicable. V+ VTEMP R3 VT1 R4 VT2 LM4040 V+ VT R1 4.1V U3 0.1 PF LM61 R2 (Low = overtemp alarm) + U1 - VOUT VOUT LM7211 VTemp U2 VT1 = (4.1)R2 R2 + R1||R3 VT2 = (4.1)R2||R3 R1 + R2||R3 Copyright (c) 2016, Texas Instruments Incorporated Figure 15. Centigrade Thermostat Figure 16. Conserving Power Dissipation with Shutdown 10 Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM61 LM61 www.ti.com SNIS121J - JUNE 1999 - REVISED NOVEMBER 2016 9 Power Supply Recommendations In an extremely noisy environment, it may be necessary to add filtering to minimize noise pickup. TI recommends a 0.1-F capacitor be added between +VS to GND to bypass the power-supply voltage, as shown in Figure 13. 10 Layout 10.1 Layout Guidelines 10.1.1 Mounting The LM61 can be applied easily in the same way as other integrated-circuit temperature sensors. It can be glued or cemented to a surface. The temperature that the LM61 senses is within about 0.2C of the surface temperature that LM61's leads are attached to. This presumes that the ambient air temperature is almost the same as the surface temperature; if the air temperature is much higher or lower than the surface temperature, the actual temperature measured would be at an intermediate temperature between the surface temperature and the air temperatures. To ensure good thermal conductivity the backside of the LM61 die is directly attached to the GND pin. The lands and traces to the LM61 are part of the printed-circuit board, which is the object whose temperature is being measured. Alternatively, the LM61 can be mounted inside a sealed-end metal tube, and can then be dipped into a bath or screwed into a threaded hole in a tank. As with any IC, the LM61 and accompanying wiring and circuits must be kept insulated and dry, to avoid leakage and corrosion. This is especially true if the circuit may operate at cold temperatures where condensation can occur. Printed-circuit coatings and varnishes such as Humiseal and epoxy paints or dips are often used to ensure that moisture cannot corrode the device or connections. 10.2 Layout Examples Figure 17. Recommended Solder Pads for SOT-23 Package Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM61 11 LM61 SNIS121J - JUNE 1999 - REVISED NOVEMBER 2016 www.ti.com Layout Examples (continued) A. 1/2 in.2 printed-circuit board with 2 oz copper foil or similar. Figure 18. Printed-Circuit Board Used for Heat Sink to Generate All Curves +VS 1 3 VO GND 2 Via to ground plane Via to power plane Figure 19. PCB Layout 10.3 Thermal Considerations The junction-to-ambient thermal resistance is the parameter used to calculate the rise of a device junction temperature due to its power dissipation. For the LM61, Equation 2 is used to calculate the rise in the die temperature. TJ = TA + RJA x ((+VS x IQ) + (+VS - VO) x IL) where * * IQ is the quiescent current ILis the load current on the output (2) Table 2 summarizes the rise in die temperature of the LM61 without any loading with a 3.3-V supply, and the thermal resistance for different conditions. 12 Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM61 LM61 www.ti.com SNIS121J - JUNE 1999 - REVISED NOVEMBER 2016 Table 2. Temperature Rise of LM61 Due to Self-Heating and Thermal Resistance (RJA) Still air No heat sink (1) Moving air SOT-23 Small heat fin (2) No heat sink (1) TO-92 Small heat fin (3) (1) (2) (3) RJA (C/W) TJ - TA (C) 450 0.26 -- -- Still air 260 0.13 Moving air 180 0.09 Still air 180 0.09 Moving air 90 0.05 Still air 140 0.07 Moving air 70 0.03 Part soldered to 30 gauge wire. Heat sink used is 1/2 in.2 printed -circuit board with 2-oz foil with part attached as shown in Figure 18. Part glued and leads soldered to 1 in.2 of 1/16 in. printed circuit board with 2-oz foil or similar. Table 3. Temperature and Typical VO Values TEMPERATURE VO(TYPICAL) 100C 1600 mV 85C 1450 mV 25C 850 mV 0C 600 mV -25C 350 mV -30C 300 mV Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM61 13 LM61 SNIS121J - JUNE 1999 - REVISED NOVEMBER 2016 www.ti.com 11 Device and Documentation Support 11.1 Related Documentation For related documentation see the following: * TO-92 Packing Options / Ordering Instructions (SNOA072) * Tiny Temperature Sensors for Remote Systems (SNIA009) 11.2 Receiving Notification of Documentation Updates To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper right corner, click on Alert me to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document. 11.3 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2ETM Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 11.4 Trademarks E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. 11.5 Electrostatic Discharge Caution This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. 11.6 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 14 Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM61 PACKAGE OPTION ADDENDUM www.ti.com 11-Jan-2021 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) (6) LM61BIM3 NRND SOT-23 DBZ 3 1000 Non-RoHS & Green Call TI Call TI -25 to 85 T1B LM61BIM3/NOPB ACTIVE SOT-23 DBZ 3 1000 RoHS & Green SN Level-1-260C-UNLIM -25 to 85 T1B LM61BIM3X/NOPB ACTIVE SOT-23 DBZ 3 3000 RoHS & Green SN Level-1-260C-UNLIM -25 to 85 T1B LM61BIZ/LFT3 ACTIVE TO-92 LP 3 2000 RoHS & Green SN N / A for Pkg Type LM61BIZ/NOPB ACTIVE TO-92 LP 3 1800 RoHS & Green SN N / A for Pkg Type -25 to 85 LM61 BIZ LM61CIM3 NRND SOT-23 DBZ 3 1000 Non-RoHS & Green Call TI Call TI -30 to 100 T1C LM61CIM3/NOPB ACTIVE SOT-23 DBZ 3 1000 RoHS & Green SN Level-1-260C-UNLIM -30 to 100 T1C LM61CIM3X/NOPB ACTIVE SOT-23 DBZ 3 3000 RoHS & Green SN Level-1-260C-UNLIM -30 to 100 T1C LM61CIZ/LFT2 ACTIVE TO-92 LP 3 2000 RoHS & Green SN N / A for Pkg Type LM61CIZ/NOPB ACTIVE TO-92 LP 3 1800 RoHS & Green SN N / A for Pkg Type LM61 BIZ LM61 CIZ -30 to 100 LM61 CIZ (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com (4) 11-Jan-2021 There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 29-Sep-2019 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) LM61BIM3 SOT-23 DBZ 3 1000 178.0 8.4 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3.3 2.9 1.22 4.0 8.0 Q3 LM61BIM3/NOPB SOT-23 DBZ 3 1000 178.0 8.4 3.3 2.9 1.22 4.0 8.0 Q3 LM61BIM3X/NOPB SOT-23 DBZ 3 3000 178.0 8.4 3.3 2.9 1.22 4.0 8.0 Q3 LM61CIM3 SOT-23 DBZ 3 1000 178.0 8.4 3.3 2.9 1.22 4.0 8.0 Q3 LM61CIM3/NOPB SOT-23 DBZ 3 1000 178.0 8.4 3.3 2.9 1.22 4.0 8.0 Q3 LM61CIM3X/NOPB SOT-23 DBZ 3 3000 178.0 8.4 3.3 2.9 1.22 4.0 8.0 Q3 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 29-Sep-2019 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM61BIM3 SOT-23 DBZ 3 1000 210.0 185.0 35.0 LM61BIM3/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0 LM61BIM3X/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0 LM61CIM3 SOT-23 DBZ 3 1000 210.0 185.0 35.0 LM61CIM3/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0 LM61CIM3X/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0 Pack Materials-Page 2 PACKAGE OUTLINE LP0003A TO-92 - 5.34 mm max height SCALE 1.200 SCALE 1.200 TO-92 5.21 4.44 EJECTOR PIN OPTIONAL 5.34 4.32 (1.5) TYP SEATING PLANE (2.54) NOTE 3 2X 4 MAX (0.51) TYP 6X 0.076 MAX SEATING PLANE 2X 2.6 0.2 3X 12.7 MIN 3X 3X 0.55 0.38 0.43 0.35 2X 1.27 0.13 FORMED LEAD OPTION STRAIGHT LEAD OPTION OTHER DIMENSIONS IDENTICAL TO STRAIGHT LEAD OPTION 3X 2.67 2.03 4.19 3.17 3 2 1 3.43 MIN 4215214/B 04/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Lead dimensions are not controlled within this area. 4. Reference JEDEC TO-226, variation AA. 5. Shipping method: a. Straight lead option available in bulk pack only. b. Formed lead option available in tape and reel or ammo pack. c. Specific products can be offered in limited combinations of shipping medium and lead options. d. Consult product folder for more information on available options. www.ti.com EXAMPLE BOARD LAYOUT LP0003A TO-92 - 5.34 mm max height TO-92 0.05 MAX ALL AROUND TYP FULL R TYP METAL TYP (1.07) 3X ( 0.85) HOLE 2X METAL (1.5) 2X (1.5) 2 1 (R0.05) TYP 3 2X (1.07) (1.27) SOLDER MASK OPENING 2X SOLDER MASK OPENING (2.54) LAND PATTERN EXAMPLE STRAIGHT LEAD OPTION NON-SOLDER MASK DEFINED SCALE:15X 0.05 MAX ALL AROUND TYP ( 1.4) 2X ( 1.4) METAL 3X ( 0.9) HOLE METAL (R0.05) TYP 2 1 (2.6) SOLDER MASK OPENING 3 2X SOLDER MASK OPENING (5.2) LAND PATTERN EXAMPLE FORMED LEAD OPTION NON-SOLDER MASK DEFINED SCALE:15X 4215214/B 04/2017 www.ti.com TAPE SPECIFICATIONS LP0003A TO-92 - 5.34 mm max height TO-92 13.7 11.7 32 23 (2.5) TYP 0.5 MIN 16.5 15.5 11.0 8.5 9.75 8.50 19.0 17.5 6.75 5.95 2.9 TYP 2.4 3.7-4.3 TYP 13.0 12.4 FOR FORMED LEAD OPTION PACKAGE 4215214/B 04/2017 www.ti.com 4203227/C PACKAGE OUTLINE DBZ0003A SOT-23 - 1.12 mm max height SCALE 4.000 SMALL OUTLINE TRANSISTOR C 2.64 2.10 1.4 1.2 PIN 1 INDEX AREA 1.12 MAX B A 0.1 C 1 0.95 3.04 2.80 1.9 3X 3 0.5 0.3 0.2 2 (0.95) C A B 0.25 GAGE PLANE 0 -8 TYP 0.10 TYP 0.01 0.20 TYP 0.08 0.6 TYP 0.2 SEATING PLANE 4214838/C 04/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Reference JEDEC registration TO-236, except minimum foot length. www.ti.com EXAMPLE BOARD LAYOUT DBZ0003A SOT-23 - 1.12 mm max height SMALL OUTLINE TRANSISTOR PKG 3X (1.3) 1 3X (0.6) SYMM 3 2X (0.95) 2 (R0.05) TYP (2.1) LAND PATTERN EXAMPLE SCALE:15X SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK 0.07 MIN ALL AROUND 0.07 MAX ALL AROUND NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS 4214838/C 04/2017 NOTES: (continued) 4. Publication IPC-7351 may have alternate designs. 5. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DBZ0003A SOT-23 - 1.12 mm max height SMALL OUTLINE TRANSISTOR PKG 3X (1.3) 1 3X (0.6) SYMM 3 2X(0.95) 2 (R0.05) TYP (2.1) SOLDER PASTE EXAMPLE BASED ON 0.125 THICK STENCIL SCALE:15X 4214838/C 04/2017 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 7. Board assembly site may have different recommendations for stencil design. www.ti.com IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES "AS IS" AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI's products are provided subject to TI's Terms of Sale (https:www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI's provision of these resources does not expand or otherwise alter TI's applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2021, Texas Instruments Incorporated