USB3250 Hi-Speed USB Device Transceiver with UTMI Interface PRODUCT FEATURES Data Brief USB-IF "Hi-Speed" certified to USB 2.0 electrical specification Interface compliant with the UTMI specification (60MHz 8-bit unidirectional interface or 30MHz 16-bit bidirectional interface) Supports 480Mbps High Speed (HS) and 12Mbps Full Speed (FS) serial data transmission rates Integrated 45 and 1.5k termination resistors reduce external component count Internal short circuit protection of DP and DM lines On-chip oscillator operates with low cost 12MHz crystal Robust and low power digital clock and data recovery circuit SYNC and EOP generation on transmit packets and detection on receive packets NRZI encoding and decoding Bit stuffing and unstuffing with error detection Supports the USB suspend state, HS detection, HS Chirp, Reset and Resume Support for all test modes defined in the USB 2.0 specification Draws 72mA (185mW) maximum current consumption in HS mode - ideal for bus powered functions On-die decoupling capacitance and isolation for immunity to digital switching noise Available in a 56-pin QFN package Full industrial operating temperature range from -40oC to +85oC (ambient) Applications The Universal Serial Bus (USB) is the preferred interface to connect Hi-Speed PC peripherals. Digital Still and Video Cameras MP3 Players External Hard Drives Scanners Entertainment Devices Printers Test and Measurement Systems POS Terminals Set Top Boxes SMSC USB3250 Revision 1.7 (02-11-13) PRODUCT PREVIEW Hi-Speed USB Device Transceiver with UTMI Interface Ordering Information: USB3250-ABZJ for 56 pin, QFN lead-free RoHS compliant package, 8 x 8 x 0.85mm This product meets the halogen maximum concentration values per IEC61249-2-21 For RoHS compliance and environmental information, please visit www.smsc.com/rohs Copyright (c) 2013 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC's website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems Corporation ("SMSC"). Product names and company names are the trademarks of their respective holders. The Microchip name and logo, and the Microchip logo are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Revision 1.7 (02-11-13) 2 PRODUCT PREVIEW SMSC USB3250 Hi-Speed USB Device Transceiver with UTMI Interface General Description The USB3250 provides the Physical Layer (PHY) interface to a USB 2.0 Device Controller. The IC is available in a 56 pin QFN. The USB3250 is a USB 2.0 physical layer transceiver (PHY) integrated circuit. SMSC's proprietary technology results in low power dissipation, which is ideal for building a bus powered USB 2.0 peripheral. The PHY can be configured for either an 8-bit unidirectional or a 16-bit bidirectional parallel interface, which complies with the USB Transceiver Macrocell Interface (UTMI) specification. It supports 480Mbps transfer rate, while remaining backward compatible with USB 1.1 legacy protocol at 12Mbps. All required termination for the USB 2.0 Transceiver is internal. Internal 5.25V short circuit protection of DP and DM lines is provided for USB compliance. While transmitting data, the PHY serializes data and generates SYNC and EOP fields. It also performs needed bit stuffing and NRZI encoding. Likewise, while receiving data, the PHY de-serializes incoming data, stripping SYNC and EOP fields and performs bit un-stuffing and NRZI decoding. SMSC USB3250 3 PRODUCT PREVIEW Revision 1.7 (02-11-13) Hi-Speed USB Device Transceiver with UTMI Interface Block Diagram XO XI VDD1.8 VDD3.3 PWR CONTROL TX LOGIC TX RPU_EN 1.5k TX State Machine VPO VMO Parallel to Serial Conversion DATABUS16_8 RESET XCVRSELECT HS_DATA HS_DRIVE_ENABLE HS_CS_ENABLE NRZ Encode TERMSELECT FS TX OEB Bit Stuff SUSPENDN System Clocking PLL and XTAL OSC HS TX DP OPMODE[1:0] RX LINESTATE[1:0] TXREADY VALIDH RXVALID RXACTIVE RX LOGIC FS SE+ RX State Machine VP VM Serial to Parallel Conversion FS SE- Clock Recovery Unit Clock and Data Recovery Bit Unstuff NRZI Decode RXERROR FS RX MUX DATA[15:0] * TXVALID UTMI Interface CLKOUT DM Elasticity Buffer BIASING Bandgap Voltage Reference HS RX HS SQ RBIAS Current Reference Figure 1 USB3250 Functional Block Diagram Revision 1.7 (02-11-13) 4 PRODUCT PREVIEW SMSC USB3250 Hi-Speed USB Device Transceiver with UTMI Interface VALIDH RXVALID TXVALID DATA[0] VDD3.3 47 46 45 44 43 CLKOUT VSS RXACTIVE 50 48 TXREADY 51 49 VDD1.8 RXERROR DATABUS16_8 54 52 VSS 55 53 VSS 56 Pin Configuration VSSA 1 42 DATA[1] DM 2 41 DATA[2] DP 3 40 DATA[3] VDDA3.3 4 39 DATA[4] VSSA 5 RBIAS 6 VDDA3.3 7 VSSA 8 VSSA USB 2.0 USB3250 PHY IC 25 26 27 28 DATA[13] VDD3.3 DATA[12] DATA[14] 29 DATA[15] 14 24 DATA[11] VSS RESET 30 23 13 VDD1.8 DATA[10] SUSPENDN 22 31 LINESTATE[0] 12 21 DATA[9] VDDA1.8 20 32 OPMODE[0] 11 LINESTATE[1] VSS XO 19 33 OPMODE[1] 10 18 DATA[8] XI TERMSELECT 34 17 DATA[7] 9 XCVRSELECT DATA[6] 35 16 36 15 DATA[5] VDD1.8 VDD1.8 37 VDD3.3 38 Figure 2 56-Pin USB3250 Pin Configuration (Top View) SMSC USB3250 5 PRODUCT PREVIEW Revision 1.7 (02-11-13) Hi-Speed USB Device Transceiver with UTMI Interface Pin Description Tables Table 1 System Interface Pins DIRECTION ACTIVE LEVEL RESET Input High Reset. Reset all state machines. After coming out of reset, must wait 5 rising edges of clock before asserting TXValid for transmit. Assertion of Reset: May be asynchronous to CLKOUT. De-assertion of Reset: Must be synchronous to CLKOUT unless RESET is asserted longer than two periods of CLKOUT. XCVRSELECT Input N/A Transceiver Select. This signal selects between the FS and HS transceivers: 0: HS transceiver enabled 1: FS transceiver enabled. TERMSELECT Input N/A Termination Select. This signal selects between the FS and HS terminations: 0: HS termination enabled 1: FS termination enabled SUSPENDN Input Low Suspend. Places the transceiver in a mode that draws minimal power from supplies. Shuts down all blocks not necessary for Suspend/Resume operation. While suspended, TERMSELECT must always be in FS mode to ensure that the 1.5k pull-up on DP remains powered. 0: Transceiver circuitry drawing suspend current 1: Transceiver circuitry drawing normal current Output Rising Edge System Clock. This output is used for clocking receive and transmit parallel data at 60MHz (8-bit mode) or 30MHz (16-bit mode). When in 8-bit mode, this specification refers to CLKOUT as CLK60. When in 16-bit mode, CLKOUT is referred to as CLK30. Input N/A Operational Mode. These signals select between the various operational modes: [1] [0] Description 0 0 0: Normal Operation 0 1 1: Non-driving (all terminations removed) 1 0 2: Disable bit stuffing and NRZI encoding 1 1 3: Reserved LINESTATE[1:0] Output N/A Line State. These signals reflect the current state of the USB data bus in FS mode, with [0] reflecting the state of DP and [1] reflecting the state of DM. When the device is suspended or resuming from a suspended state, the signals are combinatorial. Otherwise, the signals are synchronized to CLKOUT. [1] [0] Description 0 0 0: SE0 0 1 1: J State 1 0 2: K State 1 1 3: SE1 DATABUS16_8 Input N/A Databus Select. Selects between 8-bit and 16-bit data transfers. 0: 8-bit data path enabled. VALIDH is undefined. CLKOUT = 60MHz. 1: 16-bit data path enabled. CLKOUT = 30MHz. NAME CLKOUT OPMODE[1:0] Revision 1.7 (02-11-13) DESCRIPTION 6 PRODUCT PREVIEW SMSC USB3250 Hi-Speed USB Device Transceiver with UTMI Interface Table 2 Data Interface Pins NAME DATA[15:0] DIRECTION ACTIVE LEVEL DESCRIPTION Bidir N/A DATA BUS. 16-BIT BIDIRECTIONAL MODE. TXVALID RXVALID VALIDH 0 0 X DATA[15:0] Not used 0 1 0 DATA[7:0] output is valid for receive VALIDH is an output 0 1 1 DATA[15:0] output is valid for receive VALIDH is an output 1 X 0 DATA[7:0] input is valid for transmit VALIDH is an input 1 X 1 DATA[15:0] input is valid for transmit VALIDH is an input DATA BUS. 8-BIT UNIDIRECTIONAL MODE. TXVALID Input High TXVALID RXVALID DATA[15:0] 0 0 Not used 0 1 DATA[15:8] output is valid for receive 1 X DATA[7:0] input is valid for transmit Transmit Valid. Indicates that the TXDATA bus is valid for transmit. The assertion of TXVALID initiates the transmission of SYNC on the USB bus. The negation of TXVALID initiates EOP on the USB. Control inputs (OPMODE[1:0], TERMSELECT,XCVRSELECT) must not be changed on the de-assertion or assertion of TXVALID. The PHY must be in a quiescent state when these inputs are changed. TXREADY VALIDH Output High Transmit Data Ready. If TXVALID is asserted, the SIE must always have data available for clocking into the TX Holding Register on the rising edge of CLKOUT. TXREADY is an acknowledgement to the SIE that the transceiver has clocked the data from the bus and is ready for the next transfer on the bus. If TXVALID is negated, TXREADY can be ignored by the SIE. Bidir N/A Transmit/Receive High Data Bit Valid (used in 16-bit mode only). When TXVALID = 1, the 16-bit data bus direction is changed to inputs, and VALIDH is an input. If VALIDH is asserted, DATA[15:0] is valid for transmission. If deasserted, only DATA[7:0] is valid for transmission. The DATA bus is driven by the SIE. When TXVALID = 0 and RXVALID = 1, the 16-bit data bus direction is changed to outputs, and VALIDH is an output. If VALIDH is asserted, the DATA[15:0] outputs are valid for receive. If deasserted, only DATA[7:0] is valid for receive. The DATA bus is read by the SIE. RXVALID SMSC USB3250 Output High Receive Data Valid. Indicates that the RXDATA bus has received valid data. The Receive Data Holding Register is full and ready to be unloaded. The SIE is expected to latch the RXDATA bus on the rising edge of CLKOUT. 7 PRODUCT PREVIEW Revision 1.7 (02-11-13) Hi-Speed USB Device Transceiver with UTMI Interface Table 2 Data Interface Pins (continued) DIRECTION ACTIVE LEVEL RXACTIVE Output High Receive Active. Indicates that the receive state machine has detected Start of Packet and is active. RXERROR Output High Receive Error. 0: Indicates no error. 1: Indicates a receive error has been detected. This output is clocked with the same timing as the RXDATA lines and can occur at anytime during a transfer. NAME DESCRIPTION Table 3 USB I/O Pins DIRECTION ACTIVE LEVEL DP I/O N/A USB Positive Data Pin. DM I/O N/A USB Negative Data Pin. NAME DESCRIPTION Table 4 Biasing and Clock Oscillator Pins DIRECTION ACTIVE LEVEL RBIAS Input N/A External 1% bias resistor. Requires a 12K resistor to ground. Used for setting HS transmit current level and on-chip termination impedance. XI/XO Input N/A External crystal. 12MHz crystal connected from XI to XO. NAME DESCRIPTION Table 5 Power and Ground Pins DIRECTION ACTIVE LEVEL VDD3.3 N/A N/A NAME DESCRIPTION 3.3V Digital Supply. Powers digital pads. See Note 2.1 VDD1.8 N/A N/A 1.8V Digital Supply. Powers digital core. VSS N/A N/A Digital Ground. See Note 2.2 VDDA3.3 N/A N/A 3.3V Analog Supply. Powers analog I/O and 3.3V analog circuitry. VDDA1.8 N/A N/A 1.8V Analog Supply. Powers 1.8V analog circuitry. See Note 2.1 VSSA N/A N/A Analog Ground. See Note 2.2 Note 2.1 A Ferrite Bead (with DC resistance <.5 Ohms) is recommended for filtering between both the VDD3.3 and VDDA3.3 supplies and the VDD1.8 and VDDA1.8 Supplies. Note 2.2 All VSS and VSSA are bonded to the exposed pad under the IC in the package. The exposed pad must be connected to solid GND plane on printed circuit board. Revision 1.7 (02-11-13) 8 PRODUCT PREVIEW SMSC USB3250 Hi-Speed USB Device Transceiver with UTMI Interface Application Diagram VDD3.3 VDD1.8 UTMI Voltage Regulator 1uF 10uF 10uF 1uF 44 42 41 40 39 37 36 35 34 32 31 30 29 27 26 25 DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7 TXVALID TXREADY RXACTIVE RXVALID RXERROR VALIDH DATABUS16_8 17 XCVRSELECT 18 TERMSELECT 13 SUSPENDN 24 RESET DATA 8 DATA 9 DATA 10 DATA 11 DATA 12 DATA 13 DATA 14 DATA 15 20 OPMODE 0 19 OPMODE 1 LINESTATE 0 22 LINESTATE 1 21 USB C LOAD 10 45 51 50 46 52 47 54 XI CLKOUT 49 6 RBIAS DP 3 12K 1 12MHz Crystal USB-B 11 XO DM 2 C LOAD POWER 12 VDDA1.8 Ferrite Bead 10uF 16 VDD1.8 23 VDD1.8 38 VDD1.8 53 VDD1.8 VDD1.8 4 VDDA3.3 7 VDDA3.3 Ferrite Bead 15 VDD3.3 28 VDD3.3 43 VDD3.3 VSSA VSSA VSSA VSSA VSS VSS VSS VSS VSS 1 5 8 9 14 33 48 55 56 VDD3.3 GND Figure 3 Application Diagram for 56-pin QFN Package SMSC USB3250 9 PRODUCT PREVIEW Revision 1.7 (02-11-13) RE VI SIO N HIST ORY R EV ISION D D2 D1 e T E R M IN A L #1 IDEN T IF IE R AR EA (D /2 X E/2) 3 D E SC R I PTIO N D ATE R E LE AS E D BY A IN IT IA L R ELEASE 2/07/04 S .K .I LIEV B R EM O V E "PR E LIM INARY" NO TE 10/7/04 S .K .I LIEV 7/2/ 05 S .K .I LIEV L(M A X ) F R O M 0.55 T O 0.50. AD D E D D2/E2 VARIATIO NS TABLE C Revision 1.7 (02-11-13) Package Outline 3 T E R M IN A L #1 IDEN T IF IER AR EA (D 1 /2 X E 1/2) E1 E E2 E XP O S E D PAD 2 56X L 2 BOT TO M VIEW 10 T OP V IEW A2 A D 2 / E2 V ARIATIONS C ATAL OG P ART N O T ES: 1 . A LL DIM ENS IO N S A RE IN M IL LIM ETER. 2 . PO SITIO N T OL ER AN CE O F EA CH TER M INA L AN D EX PO SE D PA D IS 0 .0 5m m AT M AXIM UM M ATERIAL C ON DITION . DIM E NS IO NS "b" A PP LIES T O PL AT ED T ER M INA LS A ND IT IS M EASURED BETW EEN 0.15 AND 0.3 0 m m F RO M TH E TERM INA L TIP. 3 . DE TA IL S OF T ER M INA L #1 IDE NTIF IE R ARE OP TION AL B UT M US T BE L OC AT ED W IT HIN TH E AREA INDICATED. U N LES S O TH E R W ISE SPECIFIED D IM EN SIO N S AR E IN M ILLIMETERS AN D T O LERANCES ARE: D E C I MAL 0.1 X .X 0.05 X .XX X .X XX 0.025 T H IRD A N G LE P R O JE CT ION 80 A R KA Y DRIVE H AU P PA U G E , N Y 11788 U SA A N G U LAR 1 T IT LE N A ME D I M A N D T O L P ER A SM E Y14.5M - 1994 M A T E R IAL 3-D V IE W S F IN ISH - P R I N T W I TH "SC ALE TO FIT" D O N O T SC A LE DRAW ING D A TE DR AWN S .K.ILIEV 2 /06/04 C H EC KED S .K.ILIEV D W G N U M BER S TD C OM PLIA N CE S C ALE 2 /07/04 R EV M O -56-Q FN -8x8 2 /07/04 A PPR OVED S .K.ILIEV P AC KA G E O UTLINE 56 TE RM IN AL Q FN , 8x8m m BO DY , 0.5m m PITCH 1:1 J EDEC : MO -220 C S H EET 1 OF 1 SMSC USB3250 Hi-Speed USB Device Transceiver with UTMI Interface A1 S ID E VIEW PRODUCT PREVIEW 56X b 4X 45X 0.6 M A X (O PTIONAL)