Click on Series name for product info on aimtec.com Series AM10EW-NZ 10 Watt | DC-DC Converter FEATURES: * Efficiency up to 87% * Ultra-Wide 4:1 input range * Continuous Short Circuit Protection * Operating temperature -40oC to + 85oC * On/Off remote control * * * Input Under-voltage Protection Over Voltage, Over Current Protection I/O Isolation 1500, 2250 & 3000VDC No-load power consumption 0.12W Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (mA) I/O Isolation (VDC) Capacitive load max (F) Efficiency (%) AM10EW-2403SH30-NZ 9-36 3.3 2400 3000 5400 79 AM10EW-2405SH30-NZ 9-36 5 2000 3000 5400 82 AM10EW-2409SH30-NZ 9-36 9 1111 3000 680 85 AM10EW-2412SH30-NZ 9-36 12 833 3000 470 86 AM10EW-2415SH30-NZ 9-36 15 667 3000 330 87 AM10EW-2424SH30-NZ 9-36 24 416 3000 100 87 AM10EW-4803SH30-NZ 18-75 3.3 2400 3000 5400 79 AM10EW-4805SH30-NZ 18-75 5 2000 3000 5400 82 AM10EW-4812SH30-NZ 18-75 12 833 3000 470 86 AM10EW-4815SH30-NZ 18-75 15 667 3000 330 87 AM10EW-4824SH30-NZ 18-75 24 416 3000 100 87 AM10EW-11005S-NZ 40~160 5 2000 1500 2200 81 AM10EW-11012S-NZ 40~160 12 833 1500 220 85 AM10EW-11015S-NZ 40~160 15 667 1500 100 85 AM10EW-11024S-NZ 40~160 24 416 1500 47 86 AM10EW-11003SH22-NZ 40~160 3.3 2400 2250 5400 76 AM10EW-11005SH22-NZ 40~160 5 2000 2250 5400 80 AM10EW-11012SH22-NZ 40~160 12 833 2250 470 84 AM10EW-11015SH22-NZ 40~160 15 667 2250 330 84 AM10EW-11024SH22-NZ 40~160 24 417 2250 100 85 Add suffix "-K" for optional heat sink *Add suffix "-ST" for optional screw terminal bottom plate or "-STD" for optional DIN Rail screw terminal bottom plate. **Add suffix "-K" for optional heatsink, "-K-ST" for optional heatsink and screw terminal bottom plate or "-K-STD" for optional heatsink and DIN Rail screw terminal bottom plate. Models Dual output Model Input Voltage (V) Output Voltage (V) Output Current max (mA) I/O Isolation (VDC) Capacitive load max (F) Efficiency (%) AM10EW-2405DH30-NZ AM10EW-2412DH30-NZ AM10EW-2415DH30-NZ AM10EW-4805DH30-NZ AM10EW-4812DH30-NZ AM10EW-4815DH30-NZ 9-36 9-36 9-36 18-75 18-75 18-75 5 12 15 5 12 15 1000 416 333 1000 416 333 3000 3000 3000 3000 3000 3000 1000 330 220 1000 330 220 82 86 87 82 86 87 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Voltage range www.aimtec.com F 051e R12.H Nominal Typical 24 48 110 9-36 18-75 40~160 Tel: +1 514 620 2722 1 of 9 Maximum Units VDC Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10EW-NZ 10 Watt | DC-DC Converter 24 48 110 Input Current (full load) 521 261 117 mA 50 100 180 VDC (Pi) Network Filter 24 48 110 Nominal Input, resistive load 24 48 110 24 48 110 (2250 Isolated models) On Off Input Surge Voltage (1sec max.) Start-up time Reflected Input Ripple Current Under-voltage lockout Remote On/Off Control (24 & 48Vin) 10 40 30 30 6.5 15.5 33 ms mA V 3.5-12VDC or leave open 0-1.2VDC or connect to GND, idle current 5-6mA Isolation Specifications Parameters Conditions Tested I/O voltage Tested I/FG & O/FG Resistance 1 min, <1mA 1 min, <1Ma, 2250VDC I/O isolated models At 500VDC Isolation 24 & 48 Vin, I/O, 100KHz/0.1V 110 Vin (1500VDC isolation), I/O, 100KHz/0.1V 110 Vin (2250VDC isolation), I/O, 100KHz/0.1V Capacitance Typical Rated Units 1500, 2250 & 3000 1600 VDC VDC MOhm > 1000 500 1000 2200 pF Output Specifications Parameters Conditions Voltage accuracy Voltage balance (Dual Output Models) Line voltage regulation Load voltage regulation Cross Regulation 110 Vin (2250VDC isolation), 0-100% load Others, 5-100% load Balanced Load 110 Vin (2250VDC isolation), Full Load (HL-LL) Others, Full Load (HL-LL) 110 Vin (2250VDC isolation), 0-100% load Others, 5-100% load 50% load on one output & 10-100% load on second load Short Circuit protection Short Circuit restart Over Voltage Protection Over Current Protection Transient Recovery Time Transient Response Deviation Temperature coefficient Ripple & Noise Typical Maximum Units 1 3 % 1 0.2 0.5 0.5 0.5 2 0.5 1 1 1.5 % 5 % 160 190 210 500 1000 8 % of Vo % % Continuous Auto Recovery 120 140 120 300 500 3 0.03 60 24 & 48 Vin models 110 Vin (2250VDC isolation) 110 Vin (2250VDC isolation), 25% Load Step Change Others, 25% Load Step Change 25% Load Step Change 20Mhz bandwidth % of Io s % %/oC mV p-p 120 General Specifications Parameters Switching frequency Operating temperature Storage temperature Max case temperature Cooling Humidity Solder Temp Leads Case material www.aimtec.com F 051e R12.H Conditions Typical 110 Vin (2250VDC isolation), 100% load Others, 100% load Derating above 71C -55 to +125 Maximum 300 350 -40 to +85 Units KHz oC oC 105 oC 95 300 oC Free air convection Non-condensing 1.5 mm from case 10 sec. Plastic (3000VDC Isolated models) Aluminum Alloy (Others) Tel: +1 514 620 2722 2 of 9 % Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10EW-NZ 10 Watt | DC-DC Converter 24 (3000VDC Isolated models) Pin mountable without heatsink 22 (1500VDC Isolated models) 26 (2250VDC Isolated models) 30 (1500VDC Isolated models) Pin mountable with heatsink 34 (2250VDC Isolated models) 46 (3000VDC Isolated models) -ST option without heatsink 44 (1500VDC Isolated models) 48 (2250VDC Isolated models) g 52 (1500VDC Isolated models) -ST option with heatsink 56 (2250VDC Isolated models) 66 (3000VDC Isolated models) -STD option without heatsink 64 (1500VDC Isolated models) 68 (2250VDC Isolated models) 72 (1500VDC Isolated models) -STD option with heatsink 76 (2250VDC Isolated models) 3000VDC Isolated models 2.03 x 1.04 x 0.47 inches; 51.50 x 26.50 x 12.00mm Others 2.00 x 1.00 x 0.46 inches; 50.80 x 25.40 x 11.80mm Optional packages See dimensions drawing >1 000 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC) Weight Dimensions (L x W x H) MTBF Environmental Specifications Parameters Test mode 10-55Hz Acceleration 10G, 30min one cycle, every axis tested Test mode 5-150Hz Acceleration 2G, 30min one cycle, every axis tested Displacement 7.5mm IEC61373 car body 1 B mold Vibration (24 & 48 Vin) Vibration (110 Vin/1500VDC isolation) Vibration (110 Vin/2250VDC isolation) Safety Specifications Parameters Approvals CE, UL (3000VDC Isolated models only) EN/IEC/UL60950-1 EN 55022, class A (all models) and EMI EN50121-3-2 class A (2250 VDC Isolated models) IEC61000-4-2, Contact 6KV (110Vin), Contact 4KV (24 & 48 Vin), Criteria B IEC61000-4-3, 10V/m, Criteria A IEC61000-4-4, 4KV (110Vin), 2KV (24 & 48 Vin with the recommended EMC circuit), Criteria B IEC61000-4-5, 2KV, Criteria B, (with the recommended EMC circuit) IEC61000-4-6, 3 Vrms, 10 Vrms (2250 VDC Isolated models) Criteria A IEC61000-4-29, 0-70%, Criteria B IEC/EN/UL 60950-1 Meets EN50155 (2250 VDC Isolated models) Standards Free Air Convection Derating 71C without heatsink Output Power (%) 100 75C with heatsink 80 60 Safe Operating Area 40 20 0 - 40 - 20 0 20 40 60 71 75 80 85 100 Ambient Temperature C www.aimtec.com F 051e R12.H Tel: +1 514 620 2722 3 of 9 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10EW-NZ 10 Watt | DC-DC Converter Pin Out Specifications 3000VDC Isolated models Dimensions 3000VDC Isolated models On/Off Control -Vin +Vin - Vout Common + Vout Vin Vin + +Vout -Vout 10.16 (0.40) 4 20.32 (0.80) 2.54 (0.10) 1 15.24 (0.60) Notes: All dimensions are typical in millimeters (inches). Pin diameter Tolerance 0.10 (0.004) Case Tolerance 0.50 (0.02) 50.80 (2.00) 20.32 (0.80) 3 5.08 (0.20) 1 2 3 4 5 Dimensions of Other models 25.40 (1.00) Single 10.16 (0.40) 10.16 (0.40) 7.62 5.08 (0.30) (0.20) DIA 1.00 (0.04) Pin Out Specifications Other models Pin Bottom View 2 2 Bottom View 1 25.4 (1.00) Dual 1 2 3 4 5 6 3 20.32 (0.80) Pin 6 15.24 (0.60) 4.10 (0.16) On/Off Control -Vin +Vin - Vout No pin + Vout 26.50 (1.04) Single 1 2 3 4 5 6 12.00 (0.47) Pin 2.54 (0.10) 51.50 (2.03) 4 Built-in Stand-offs to ease PCB cleaning 50.8 (2.00) 11.80 (0.47) Notes: All dimensions are typical in millimeters (inches). Tolerance 0.25 (0.01) DIA 1.00 (0.04) www.aimtec.com F 051e R12.H Tel: +1 514 620 2722 4 of 9 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10EW-NZ 10 Watt | DC-DC Converter 16.50 (0.65) Dimensions of the preinstalled heatsink option 4.10 (0.16) Side view 2.94 (0.12) DIA 1.00 (0.04) 7.62 5.08 (0.30) (0.20) 3 Bottom View 5 10.16 (0.40) 2 4 20.32 (0.80) 2.94 (0.12) 1 15.54 (0.61) 10.16 (0.40) 10.56 (0.42) 6 15.54 (0.61) Notes: All dimensions are typical in millimeters (inches). Pin diameter Tolerance: 0.10 (0.004) Case Tolerance: 0.50 (0.02) Dimensions with -ST options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 2 6 Top view 3 23.00 (0.91) 31.50 (1.24) 1 5 Pin Single 1 2 3 4 5 6 N.C. -Vin +Vin + Vout N.C. - Vout 4 8.80 (0.35) Side view 21.20 (0.84) Dimensions: mm (inch) Case Tolerance: 0.50 (0.02) Wire gauge: 24-12AWG www.aimtec.com F 051e R12.H Tel: +1 514 620 2722 5 of 9 3000VDC Isolated models Pin Single 1 2 3 4 5 6 On/Off Control -Vin +Vin - Vout No pin + Vout Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10EW-NZ 10 Watt | DC-DC Converter Pin Out Specifications Dimensions with -STD options 76.00 (2.99) 61.60 (2.43) LED light 6 Top view 2 23.00 (0.91) 31.50 (1.24) 1 5 3 4 Single 1 2 3 4 5 6 N.C. -Vin +Vin + Vout N.C. - Vout 3000VDC Isolated models 9.80 (0.39) O3.30 O0.13 25.80 (1.02) Side view Pin Pin Single 1 2 3 4 5 6 On/Off Control -Vin +Vin - Vout No pin + Vout Dimensions: mm (inch) Case Tolerance: 1.00 (0.04) Wire gauge: 24-12AWG Dimensions with heatsink and -ST options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 2 6 Top view 3 23.00 (0.91) 31.50 (1.24) 1 5 Pin Single 1 2 3 4 5 6 N.C. -Vin +Vin + Vout N.C. - Vout 4 21.20 (0.84) Side view 8.80 (0.35) 25.30 (1.00) Dimensions: mm (inch) Case Tolerance: 0.50 (0.02) 3000VDC Wire gauge: 24-12AWG www.aimtec.com F 051e R12.H Tel: +1 514 620 2722 6 of 9 Isolated models Pin Single 1 2 3 4 5 6 On/Off Control -Vin +Vin - Vout No pin + Vout Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10EW-NZ 10 Watt | DC-DC Converter Dimensions with heatsink and -STD options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 6 Top view 2 5 3 Single 1 2 3 4 5 6 N.C. -Vin +Vin + Vout N.C. - Vout 23.00 (0.91) 31.50 (1.24) 1 Pin 4 O3.30 O0.13 9.80 (0.39) 3000VDC Isolated models 25.80 (1.02) 29.90 (1.18) Side view Pin Single 1 2 3 4 5 6 On/Off Control -Vin +Vin - Vout No pin + Vout Dimensions: mm (inch) Case Tolerance: 0.50 (0.02) Wire gauge: 24-12AWG EMC recommended filter 110Vin models CY1 1nF/2KV F1 +Vin LCM 22mH R1 C1 MOV C2 +Vo C3 D1 DC-DC Converter -Vin -Vo CY2 1nF/2KV MOV C1 & C2 R1 C3 D1 S20K130 1 F / 200V 1 100 F / 200V ER304 www.aimtec.com F 051e R12.H Tel: +1 514 620 2722 7 of 9 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10EW-NZ 10 Watt | DC-DC Converter EMC recommended filter 3000VDC Isolated models CY1 1nF/3KV 24Vin single output models LDM 4.7H F1 +Vin +Vo C1 MOV C4 C2 DC-DC Converter -Vin -Vo CY1 1nF/3KV MOV C1 C2 C4 CY1 & CY2 LDM S20K30 330 F / 50V 1 F / 50V 10 F / 50V 1 nF / 3KV 4.7 H CY1 1nF/3KV 48Vin single output models LCM 6.8mH F1 +Vin +Vo C1 MOV C2 C3 -Vin C4 DC-DC Converter -Vo MOV C1 C2 & C3 C4 S20K60 330 F / 100V 1 F / 100V 10 F / 50V CY1 1nF/3KV CY1 1nF/3KV 3000VDC Isolated dual output models LCM 4.7mH F1 +Vo +Vin C4 C1 MOV C2 C3 Com DC-DC Converter -Vin C5 -Vo Vin MOV C1 C2 & C3 C4 & C5 24V 28V S20K30 S20K60 330 F / 50V 330 F / 100V 1 F / 50V 1 F / 100V 10 F / 50V CY1 1nF/3KV NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled www.aimtec.com F 051e R12.H Tel: +1 514 620 2722 8 of 9 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10EW-NZ 10 Watt | DC-DC Converter by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec's standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R12.H Tel: +1 514 620 2722 9 of 9 Toll free: + 1 888 9 AIMTEC (924 6832) North America only