KingbrightCatalog2010-2012
003
BSI
R
E
G
I
S
T
E
R
E
D
UKAS
QUALITY
MANAGEMENT
003
BSI
R
E
G
I
S
T
E
R
E
D
UKAS
QUALITY
MANAGEMENT
BSI
R
E
G
I
S
T
E
R
E
D
003
UKAS
ENVIRONMENTAL
MANAGEMENT
5711101002
High Brightness PLCC LEDs 2
High Brightness Ceramic LEDs 5
High Brightness LEDs 8
SMD LED 9
Top-Emitting PLCC SMD LED 9
Top-Emitting Chip SMD LED 10
Right Angle SMD LED 16
Multi-Color SMD LED 19
Subminiature SMD LED 23
Reverse Mount SMD LED 25
SOT-23 SMD LED 25
Ambient Light Sensor 26
Color Sensor 26
Through-Hole LED 27
Subminiature LED 27
Round LED 27
Oval LED 31
Flat Top LED 32
Rectangular LED 32
Cylindrical LED 35
Multi-Color LED 35
Low Current LED 39
Blinking LED 40
Resistor LED 40
Super Flux LED 41
Side View 42
Tape and Reel Selections 43
SMD Display 44
7-Segment SMD Display 44
Alphanumeric SMD Display 46
Through-Hole Display 47
Single Digit 7-Segment Through-Hole Display 47
Dual Digit 7-Segment Through-Hole Display 53
Three Digit 7-Segment Through-Hole Display 55
Four Digit 7-Segment Through-Hole Display
57
Alphanumeric Through-Hole Display 60
Dot Matrix 63
LED LIGHT BAR 73
Bar Graph Array 73
Light Bar 74
Circuit Board Indicator 77
Single-Level CBI 77
Bi-Level CBI 80
Tri-Level CBI 83
Quad-Level CBI 84
With Spacer 84
SMD CBI 85
LED Clips and Mounts 86
Infrared & Phototransistor 88
Infrared Emitting Diode 88
Phototransistor 90
SMD LED
9
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KA-2214SURSK AlGaInP 630 water clear 180 400 120°
2.2mm x 1.4mm
KA-2214SESK AlGaInP 601 water clear 280 450 120°
KA-2214MGS AlGaInP 570 water clear 50 150 120°
KA-2214CGSK AlGaInP 570 water clear 50 100 120°
KA-2214ZGS InGaN 525 water clear 280 550 120°
KA-2214QBS-G InGaN 465 water clear 110 300 120°
KA-3021SURCKT AlGaInP 630 water clear 70 200 125° 3.0mm x 2.0mm (1208)
KA-3021SECKT AlGaInP 601 water clear 180 400 125°
KA-3021SYCKT AlGaInP 590 water clear 110 200 125°
KA-3021MGCT AlGaInP 570 water clear 50 100 125°
KA-3021CGCKT AlGaInP 570 water clear 50 85 125°
KA-3021ZGCT InGaN 525 water clear 380 500 125°
KA-3021ZGCT-E InGaN 525 water clear 900 1500 125°
KA-3021ZGCT-G InGaN 525 water clear 1200 1600 125°
KA-3021QBCT-D InGaN 470 water clear 50 150 125°
KA-3021QBCT-F InGaN 465 water clear 110 250 125°
KA-3021QBCT-G InGaN 465 water clear 180 350 125°
KA-3022ECT-4.5SF GaAsP/GaP 625 water clear 7 30 90° 3.0mm x 2.2mm
KA-3022SRCT-4.5SF GaAlAs 640 water clear 36 150 90°
KA-3022YCT-4.5SF GaAsP/GaP 588 water clear 4 15 90°
KA-3022SGCT-4.5SF GaP 568 water clear 7 20 90°
KA-3022ZGCT-4.5SF InGaN 525 water clear 280 500 90°
KA-3022ZGCT-E-4.5SF InGaN 525 water clear 380 800 90°
KA-3022ZGCT-G-4.5SF InGaN 525 water clear 480 900 90°
KA-3022QBCT-D-4.5SF InGaN 470 water clear 50 150 90°
KA-3022QBCT-F-4.5SF InGaN 465 water clear 70 180 90°
KA-3022QBCT-G-4.5SF InGaN 465 water clear 110 250 90°
Units : mm(inch)
Tolerance : ±0.25(0.01)
Units : mm(inch)
Tolerance : ±0.25(0.01)
Units : mm(inch)
Tolerance : ±0.2(0.008)
KA-2214
KA-3021
TOP-EMITTING PLCC SMD LED
KA-3022-4.5SF
SMD LED
10
SMD LED
11
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KA-3528ECT GaAsP/GaP 625 water clear 7 30 120° 3.5mm x 2.8mm
KA-3528SRCT GaAlAs 640 water clear 50 150 120°
KA-3528SURCKT AlGaInP 630 water clear 70 350 120°
KA-3528SECKT AlGaInP 601 water clear 110 400 120°
KA-3528YCT GaAsP/GaP 588 water clear 4 20 120°
KA-3528SYCKT AlGaInP 590 water clear 70 200 120°
KA-3528SGCT GaP 568 water clear 10 25 120°
KA-3528MGCT AlGaInP 570 water clear 50 150 120°
KA-3528CGCKT AlGaInP 570 water clear 36 100 120°
KA-3528ZGCT InGaN 525 water clear 380 600 120°
KA-3528ZGCT-E InGaN 525 water clear 480 900 120°
KA-3528ZGCT-G InGaN 525 water clear 650 1000 120°
KA-3528QBCT-D InGaN 470 water clear 50 150 120°
KA-3528QBCT-F InGaN 465 water clear 110 280 120°
KA-3528QBCT-G InGaN 465 water clear 180 370 120°
TOP-EMITTING PLCC SMD LED
Units : mm(inch)
Tolerance : ±0.25(0.01)
KA-3528
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KPHHS-1005SURCK AlGaInP 630 water clear 70 220 120°
1.0mm x 0.5mm x 0.5mm (0402)
KPHHS-1005SECK AlGaInP 601 water clear 70 240 120°
KPHHS-1005SYCK AlGaInP 590 water clear 50 150 120°
KPHHS-1005CGCK AlGaInP 570 water clear 10 50 120°
KPHHS-1005ZGC-V InGaN 525 water clear 110 300 120°
KPHHS-1005QBC-D-V InGaN 470 water clear 36 100 120°
KP-1608SURCK AlGaInP 630 water clear 70 220 120° 1.6mm x 0.8mm x 1.1mm (0603)
KP-1608SECK AlGaInP 601 water clear 70 240 120°
KP-1608SYCK AlGaInP 590 water clear 50 150 120°
KP-1608MGC AlGaInP 570 water clear 36 70 120°
KP-1608CGCK AlGaInP 570 water clear 10 50 120°
KP-1608ZGC InGaN 525 water clear 110 300 120°
KP-1608ZGC-E InGaN 525 water clear 280 650 120°
KP-1608ZGC-G InGaN 525 water clear 380 700 120°
KP-1608QBC-D InGaN 470 water clear 36 100 120°
KP-1608QBC-F InGaN 465 water clear 50 150 120°
KP-1608QBC-G InGaN 465 water clear 70 180 120°
Units : mm(inch)
Tolerance : ±0.1(0.004)
KPHHS-1005
KP-1608
TOP-EMITTING CHIP SMD LED
Units : mm(inch)
Tolerance : 0.1(0.004)
NOTE:
1.KP series custom-made is available upon request.
SMD LED
10
SMD LED
11
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KPT-1608EC GaAsP/GaP 625 water clear 4 15 120° 1.6mm x 0.8mm x 0.75mm (0603 Super Thin)
KPT-1608SRC-PRV GaAlAs 640 water clear 36 100 120°
KPT-1608SURCK AlGaInP 630 water clear 70 220 120°
KPT-1608SECK AlGaInP 601 water clear 70 240 120°
KPT-1608YC GaAsP/GaP 588 water clear 2.6 8 120°
KPT-1608SYCK AlGaInP 590 water clear 50 150 120°
KPT-1608SGC GaP 568 water clear 4 15 120°
KPT-1608MGC AlGaInP 570 water clear 36 70 120°
KPT-1608CGCK AlGaInP 570 water clear 10 50 120°
KPT-1608ZGC InGaN 525 water clear 110 300 120°
KPT-1608ZGC-E InGaN 525 water clear 280 650 120°
KPT-1608ZGC-G InGaN 525 water clear 380 700 120°
KPT-1608QBC-D InGaN 470 water clear 36 100 120°
KPT-1608QBC-F InGaN 465 water clear 50 150 120°
KPT-1608QBC-G InGaN 465 water clear 70 180 120°
KPTD-1608SURCK AlGaInP 630 water clear 480 700 60° 1.6mm x 0.8mm x 0.95mm (Dome Lens)
KPTD-1608SECK AlGaInP 601 water clear 480 800 60°
KPTD-1608SYCK AlGaInP 590 water clear 280 480 60°
KPTD-1608MGC AlGaInP 570 water clear 110 250 60°
KPTD-1608CGCK AlGaInP 570 water clear 70 180 60°
KPTD-1608ZGC InGaN 525 water clear 380 780 60°
KPTD-1608ZGC-E InGaN 525 water clear 480 850 60°
KPTD-1608ZGC-G InGaN 525 water clear 650 1200 60°
KPTD-1608QBC-D InGaN 470 water clear 70 250 40°
KPTD-1608QBC-F InGaN 465 water clear 110 270 40°
KPTD-1608QBC-G InGaN 465 water clear 180 300 40°
KP-2012EC GaAsP/GaP 625 water clear 4 15 120° 2.0mm x 1.25mm x 1.1mm (0805)
KP-2012SRC-PRV GaAlAs 640 water clear 36 100 120°
KP-2012SURCK AlGaInP 630 water clear 70 220 120°
KP-2012SECK AlGaInP 601 water clear 70 240 120°
KP-2012YC GaAsP/GaP 588 water clear 2.6 8 120°
KP-2012SYCK AlGaInP 590 water clear 50 150 120°
KP-2012SGC GaP 568 water clear 4 15 120°
KP-2012MGC AlGaInP 570 water clear 36 70 120°
KP-2012CGCK AlGaInP 570 water clear 10 50 120°
KP-2012ZGC InGaN 525 water clear 110 300 120°
KP-2012ZGC-E InGaN 525 water clear 280 650 120°
KP-2012ZGC-G InGaN 525 water clear 380 700 120°
KP-2012QBC-D InGaN 470 water clear 36 100 120°
KP-2012QBC-F InGaN 465 water clear 50 150 120°
KP-2012QBC-G InGaN 465 water clear 70 180 120°
Units : mm(inch)
Tolerance : ±0.1(0.004)
Units : mm(inch)
Tolerance : ±0.15(0.006)
Units : mm(inch)
Tolerance : ±0.1(0.004)
KPT-1608
KPTD-1608
KP-2012
TOP-EMITTING CHIP SMD LED
NOTE:
1.KP series custom-made is available upon request.
SMD LED
12
SMD LED
13
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KPT-2012SURCK AlGaInP 630 water clear 70 220 120° 2.0mm x 1.25mm x 0.75mm
KPT-2012SECK AlGaInP 601 water clear 70 240 120°
KPT-2012SYCK AlGaInP 590 water clear 50 150 120°
KPT-2012MGC AlGaInP 570 water clear 36 70 120°
KPT-2012CGCK AlGaInP 570 water clear 10 50 120°
KPT-2012ZGC InGaN 525 water clear 110 300 120°
KPT-2012ZGC-E InGaN 525 water clear 280 650 120°
KPT-2012ZGC-G InGaN 525 water clear 380 700 120°
KPT-2012QBC-D InGaN 470 water clear 36 100 120°
KPT-2012QBC-F InGaN 465 water clear 50 150 120°
KPT-2012QBC-G InGaN 465 water clear 70 180 120°
KPTC-2012SURCK AlGaInP 630 water clear 70 220 120° 2.0mm x 1.25mm x 0.75mm
KPTC-2012SECK AlGaInP 601 water clear 70 240 120°
KPTC-2012SYCK AlGaInP 590 water clear 50 150 120°
KPTC-2012MGC AlGaInP 570 water clear 36 70 120°
KPTC-2012CGCK AlGaInP 570 water clear 10 50 120°
KPTC-2012ZGC InGaN 525 water clear 110 300 120°
KPTC-2012ZGC-E InGaN 525 water clear 280 650 120°
KPTC-2012ZGC-G InGaN 525 water clear 380 700 120°
KPTC-2012QBC-D InGaN 470 water clear 36 100 120°
KPTC-2012QBC-F InGaN 465 water clear 50 150 120°
KPTC-2012QBC-G InGaN 465 water clear 70 180 120°
KPHCM-2012SURCK AlGaInP 630 water clear 70 220 110° 2.0mm x 1.25mm x 0.4mm (0805 Super Thin)
KPHCM-2012SECK AlGaInP 601 water clear 70 240 110°
KPHCM-2012SYCK AlGaInP 590 water clear 50 150 110°
KPHCM-2012CGCK AlGaInP 570 water clear 10 50 110°
KPHCM-2012ZGC InGaN 525 water clear 110 300 110°
KPHCM-2012ZGC-E InGaN 525 water clear 280 650 110°
KPHCM-2012ZGC-G InGaN 525 water clear 380 700 110°
KPHCM-2012QBC-D InGaN 470 water clear 36 100 110°
KPHCM-2012QBC-F InGaN 465 water clear 50 150 110°
KPHCM-2012QBC-G InGaN 465 water clear 70 180 110°
KPHCM-2012
Units : mm(inch)
Tolerance : ±0.1(0.004)
Units : mm(inch)
Tolerance : ±0.1(0.004)
Units : mm(inch)
Tolerance : ±0.1(0.004)
KPT-2012
KPTC-2012
TOP-EMITTING CHIP SMD LED
NOTE:
1.KP series custom-made is available upon request.
SMD LED
12
SMD LED
13
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KP-23SURCK-F AlGaInP 630 water clear 70 220 120° 3.0mm x 2.4mm x 1.05mm
KP-23SECK-F AlGaInP 601 water clear 70 240 120°
KP-23SYCK-F AlGaInP 590 water clear 50 150 120°
KP-23MGC-F AlGaInP 570 water clear 36 70 120°
KP-23CGCK-F AlGaInP 570 water clear 18 50 120°
KP-23ZGC-F InGaN 525 water clear 110 380 120°
KP-23ZGC-E-F InGaN 525 water clear 280 650 120°
KP-23ZGC-G-F InGaN 525 water clear 380 700 120°
KP-23QBC-D-F InGaN 470 water clear 36 100 120°
KP-23QBC-F-F InGaN 465 water clear 50 120 120°
KP-23QBC-G-F InGaN 465 water clear 70 180 120°
KPL-3015SURCK AlGaInP 630 water clear 280 500 70° 3.0mm x 1.5mm x 1.4mm (1106)
KPL-3015SECK AlGaInP 601 water clear 280 550 70°
KPL-3015SYCK AlGaInP 590 water clear 110 300 70°
KPL-3015MGC AlGaInP 570 water clear 70 140 70°
KPL-3015CGCK AlGaInP 570 water clear 50 100 70°
KPL-3015ZGC InGaN 525 water clear 380 850 70°
KPL-3015ZGC-E InGaN 525 water clear 650 1300 70°
KPL-3015ZGC-G InGaN 525 water clear 900 1500 70°
KPL-3015QBC-D InGaN 470 water clear 70 180 70°
KPL-3015QBC-F InGaN 465 water clear 110 250 70°
KPL-3015QBC-G InGaN 465 water clear 180 320 70°
KP-3216EC GaAsP/GaP 625 water clear 4 15 120° 3.2mm x 1.6mm x 1.1mm (1206)
KP-3216SRC-PRV GaAlAs 640 water clear 36 100 120°
KP-3216SURCK AlGaInP 630 water clear 70 220 120°
KP-3216SECK AlGaInP 601 water clear 70 240 120°
KP-3216YC GaAsP/GaP 588 water clear 2.6 8 120°
KP-3216SYCK AlGaInP 590 water clear 50 150 120°
KP-3216SGC GaP 568 water clear 4 15 120°
KP-3216MGC AlGaInP 570 water clear 36 70 120°
KP-3216CGCK AlGaInP 570 water clear 10 50 120°
KP-3216ZGC InGaN 525 water clear 110 300 120°
KP-3216ZGC-E InGaN 525 water clear 280 650 120°
KP-3216ZGC-G InGaN 525 water clear 380 700 120°
KP-3216QBC-D InGaN 470 water clear 36 100 120°
KP-3216QBC-F InGaN 465 water clear 50 150 120°
KP-3216QBC-G InGaN 465 water clear 70 180 120°
Units : mm(inch)
Tolerance : ±0.2(0.008)
KP-23-F
Units : mm(inch)
Tolerance : ±0.2(0.008)
Units : mm(inch)
Tolerance : ±0.2(0.008)
KPL-3015
KP-3216
TOP-EMITTING CHIP SMD LED
NOTE:
1.KP series custom-made is available upon request.
SMD LED
14
SMD LED
15
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KPT-3216SURCK AlGaInP 630 water clear 70 220 120° 3.2mm x 1.6mm x 0.75mm (1206 Super Thin)
KPT-3216SECK AlGaInP 601 water clear 70 240 120°
KPT-3216SYCK AlGaInP 590 water clear 50 150 120°
KPT-3216MGC AlGaInP 570 water clear 36 70 120°
KPT-3216CGCK AlGaInP 570 water clear 10 50 120°
KPT-3216ZGC InGaN 525 water clear 110 300 120°
KPT-3216ZGC-E InGaN 525 water clear 280 650 120°
KPT-3216ZGC-G InGaN 525 water clear 380 700 120°
KPT-3216QBC-D InGaN 470 water clear 36 100 120°
KPT-3216QBC-F InGaN 465 water clear 50 150 120°
KPT-3216QBC-G InGaN 465 water clear 70 180 120°
KPC-3216SURCK AlGaInP 630 water clear 70 220 120° 3.2mm x 1.6mm x 1.1mm (1206)
KPC-3216SECK AlGaInP 601 water clear 70 240 120°
KPC-3216SYCK AlGaInP 590 water clear 50 150 120°
KPC-3216MGC AlGaInP 570 water clear 36 70 120°
KPC-3216CGCK AlGaInP 570 water clear 10 50 120°
KPC-3216ZGC InGaN 525 water clear 110 300 120°
KPC-3216ZGC-E InGaN 525 water clear 280 650 120°
KPC-3216ZGC-G InGaN 525 water clear 380 700 120°
KPC-3216QBC-D InGaN 470 water clear 36 100 120°
KPC-3216QBC-F InGaN 465 water clear 50 150 120°
KPC-3216QBC-G InGaN 465 water clear 70 180 120°
KPTL-3216SURCK AlGaInP 630 water clear 280 550 70° 3.2mm x 1.6mm x 1.1mm (1206)
KPTL-3216SECK AlGaInP 601 water clear 280 600 70°
KPTL-3216SYCK AlGaInP 590 water clear 110 350 70°
KPTL-3216CGCK AlGaInP 570 water clear 70 200 70°
KPTL-3216ZGC InGaN 525 water clear 480 1100 70°
KPTL-3216ZGC-E InGaN 525 water clear 650 1600 70°
KPTL-3216ZGC-G InGaN 525 water clear 900 1800 70°
KPTL-3216QBC-D InGaN 470 water clear 110 300 70°
KPTL-3216QBC-F InGaN 465 water clear 180 360 70°
KPTL-3216QBC-G InGaN 465 water clear 280 400 70°
Units : mm(inch)
Tolerance : ±0.2(0.008)
Units : mm(inch)
Tolerance : ±0.2(0.008)
KPT-3216
KPC-3216
TOP-EMITTING CHIP SMD LED
NOTE:
1.KP series custom-made is available upon request.
Units : mm(inch)
Tolerance : 0.1(0.004)
KPTL-3216
SMD LED
14
SMD LED
15
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KPTD-3216SURCK AlGaInP 630 water clear 480 1500 50° 3.2mm x 1.6mm x 1.8mm (1206 Dome Lens)
KPTD-3216SECK AlGaInP 601 water clear 650 1600 50°
KPTD-3216SYCK AlGaInP 590 water clear 380 900 50°
KPTD-3216MGC AlGaInP 570 water clear 110 450 50°
KPTD-3216CGCK AlGaInP 570 water clear 110 300 50°
KPTD-3216ZGC InGaN 525 water clear 900 2000 50°
KPTD-3216ZGC-E InGaN 525 water clear 2200 3500 50°
KPTD-3216ZGC-G InGaN 525 water clear 2500 4000 50°
KPTD-3216QBC-D InGaN 470 water clear 280 500 40°
KPTD-3216QBC-F InGaN 465 water clear 380 850 40°
KPTD-3216QBC-G InGaN 465 water clear 480 900 40°
KPD-3224SURCK AlGaInP 630 water clear 650 2500 20° 3.2mm x 2.4mm x 2.4mm (Dome Lens)
KPD-3224SECK AlGaInP 601 water clear 900 2600 20°
KPD-3224SYCK AlGaInP 590 water clear 480 1400 20°
KPD-3224MGC AlGaInP 570 water clear 380 700 20°
KPD-3224CGCK AlGaInP 570 water clear 280 700 20°
KPD-3224ZGC InGaN 525 water clear 1200 2400 20°
KPD-3224ZGC-E InGaN 525 water clear 2800 5000 20°
KPD-3224ZGC-G InGaN 525 water clear 3300 5300 20°
KPD-3224QBC-D InGaN 470 water clear 380 900 20°
KPD-3224QBC-F InGaN 465 water clear 480 1200 20°
KPD-3224QBC-G InGaN 465 water clear 650 1400 20°
KPED-3528SURCK AlGaInP 630 water clear 380 800 40° 3.5mm x 2.8mm x 3.2mm (Dome Lens)
KPED-3528SECK AlGaInP 601 water clear 480 900 40°
KPED-3528SYCK AlGaInP 590 water clear 180 500 40°
KPED-3528MGC AlGaInP 570 water clear 110 250 40°
KPED-3528CGCK AlGaInP 570 water clear 70 200 40°
KPED-3528ZGC InGaN 525 water clear 480 1400 40°
KPED-3528ZGC-E InGaN 525 water clear 1800 2700 40°
KPED-3528ZGC-G InGaN 525 water clear 2200 3000 40°
KPED-3528QBC-D InGaN 470 water clear 180 500 40°
KPED-3528QBC-F InGaN 465 water clear 380 700 40°
KPED-3528QBC-G InGaN 465 water clear 480 800 40°
Units : mm(inch)
Tolerance : ±0.2(0.008)
Units : mm(inch)
Tolerance : ±0.1(0.004)
Units : mm(inch)
Tolerance : ±0.2(0.008)
KPTD-3216
KPD-3224
KPED-3528
TOP-EMITTING CHIP SMD LED
NOTE:
1.KP series custom-made is available upon request.
SMD LED
16
SMD LED
17
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KPA-1606SURCK AlGaInP 630 water clear 110 250 110° 1.6mm x 0.6mm x 1.2mm (0602 Right Angle)
KPA-1606SECK AlGaInP 601 water clear 110 300 110°
KPA-1606SYCK AlGaInP 590 water clear 50 150 110°
KPA-1606CGCK AlGaInP 570 water clear 18 60 110°
KPA-1606ZGC InGaN 525 water clear 110 350 110°
KPA-1606ZGC-E InGaN 525 water clear 280 600 110°
KPA-1606ZGC-G InGaN 525 water clear 380 650 110°
KPA-1606QBC-D InGaN 470 water clear 36 90 110°
KPA-1606QBC-F InGaN 465 water clear 50 120 110°
KPA-1606QBC-G InGaN 465 water clear 70 150 110°
KPA-2106SURCK AlGaInP 630 water clear 110 250 120° 2.1mm x 0.6mm x 1.0mm (0802 Right Angle)
KPA-2106SECK AlGaInP 601 water clear 110 300 120°
KPA-2106SYCK AlGaInP 590 water clear 50 150 120°
KPA-2106MGC AlGaInP 570 water clear 36 80 120°
KPA-2106CGCK AlGaInP 570 water clear 18 60 120°
KPA-2106ZGC InGaN 525 water clear 110 350 120°
KPA-2106ZGC-E InGaN 525 water clear 280 600 120°
KPA-2106ZGC-G InGaN 525 water clear 380 650 120°
KPA-2106QBC-D InGaN 470 water clear 36 90 120°
KPA-2106QBC-F InGaN 465 water clear 50 120 120°
KPA-2106QBC-G InGaN 465 water clear 70 150 120°
TOP-EMITTING CHIP SMD LED
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KPED-3820SURCK AlGaInP 630 water clear 280 700 60°(H)
35°(V)
3.8mm x 2.0mm x 3.2mm (Dome Lens)
KPED-3820SECK AlGaInP 601 water clear 280 800 60°(H)
35°(V)
KPED-3820SYCK AlGaInP 590 water clear 110 450 60°(H)
35°(V)
KPED-3820MGC AlGaInP 570 water clear 110 250 60°(H)
35°(V)
KPED-3820CGCK AlGaInP 570 water clear 70 170 60°(H)
35°(V)
KPED-3820ZGC InGaN 525 water clear 480 1200 60°(H)
35°(V)
KPED-3820ZGC-E InGaN 525 water clear 1500 2500 60°(H)
35°(V)
KPED-3820ZGC-G InGaN 525 water clear 1800 2700 60°(H)
35°(V)
KPED-3820QBC-D InGaN 470 water clear 110 300 60°(H)
35°(V)
KPED-3820QBC-F InGaN 465 water clear 280 450 60°(H)
35°(V)
KPED-3820QBC-G InGaN 465 water clear 380 650 60°(H)
35°(V)
Units : mm(inch)
Tolerance : ±0.2(0.008)
KPED-3820
TOP-EMITTING CHIP SMD LED
Units : mm(inch)
Tolerance : ±0.1(0.004)
Units : mm(inch)
Tolerance : ±0.1(0.004)
KPA-1606
KPA-2106
RIGHT ANGLE SMD LED
NOTE:
1.KP series custom-made is available upon request.
SMD LED
16
SMD LED
17
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KPJA-2107SURCK AlGaInP 630 water clear 110 250 120° 2.1mm x 0.7mm x 1.3mm (0802 Right Angle)
KPJA-2107SECK AlGaInP 601 water clear 110 300 120°
KPJA-2107SYCK AlGaInP 590 water clear 50 150 120°
KPJA-2107MGC AlGaInP 570 water clear 36 80 120°
KPJA-2107CGCK AlGaInP 570 water clear 18 60 120°
KPJA-2107ZGC InGaN 525 water clear 110 350 120°
KPJA-2107ZGC-E InGaN 525 water clear 280 600 120°
KPJA-2107ZGC-G InGaN 525 water clear 380 650 120°
KPJA-2107QBC-D InGaN 470 water clear 36 90 120°
KPJA-2107QBC-F InGaN 465 water clear 50 120 120°
KPJA-2107QBC-G InGaN 465 water clear 70 150 120°
KPA-3010SURCK AlGaInP 630 water clear 110 250 120° 3.0mm x 1.0mm x 2.0mm (1104 Right Angle)
KPA-3010SECK AlGaInP 601 water clear 110 300 120°
KPA-3010SYCK AlGaInP 590 water clear 50 150 120°
KPA-3010MGC AlGaInP 570 water clear 36 80 120°
KPA-3010CGCK AlGaInP 570 water clear 18 60 120°
KPA-3010ZGC InGaN 525 water clear 110 350 120°
KPA-3010ZGC-E InGaN 525 water clear 280 600 120°
KPA-3010ZGC-G InGaN 525 water clear 380 650 120°
KPA-3010QBC-D InGaN 470 water clear 36 90 120°
KPA-3010QBC-F InGaN 465 water clear 50 120 120°
KPA-3010QBC-G InGaN 465 water clear 70 150 120°
KPA-3210SURCK AlGaInP 630 water clear 110 250 120° 3.2mm x 1.0mm x 1.5mm (1304 Right Angle)
KPA-3210SECK AlGaInP 601 water clear 110 300 120°
KPA-3210SYCK AlGaInP 590 water clear 50 150 120°
KPA-3210MGC AlGaInP 570 water clear 36 80 120°
KPA-3210CGCK AlGaInP 570 water clear 18 60 120°
KPA-3210ZGC InGaN 525 water clear 110 350 120°
KPA-3210ZGC-E InGaN 525 water clear 280 600 120°
KPA-3210ZGC-G InGaN 525 water clear 380 650 120°
KPA-3210QBC-D InGaN 470 water clear 36 90 120°
KPA-3210QBC-F InGaN 465 water clear 50 120 120°
KPA-3210QBC-G InGaN 465 water clear 70 150 120°
Units : mm(inch)
Tolerance : ±0.15(0.006)
Units : mm(inch)
Tolerance : ±0.1(0.004)
Units : mm(inch)
Tolerance : 0.15(0.006)
KPJA-2107
KPA-3010
KPA-3210
RIGHT ANGLE SMD LED
NOTE:
1.KP series custom-made is available upon request.
SMD LED
18
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KA-2810ASURSK AlGaInP 630 water clear 70 200 110° 2.8mm x 0.8mm Right Angle
KA-2810ASESK AlGaInP 601 water clear 110 270 110°
KA-2810ASYSK AlGaInP 590 water clear 110 200 110°
KA-2810ACGSK AlGaInP 570 water clear 36 70 110°
KA-2810AZGS InGaN 525 water clear 380 750 110°
KA-2810AZGS-E InGaN 525 water clear 650 1300 110°
KA-2810AZGS-G InGaN 525 water clear 900 1500 110°
KA-2810AQBS-D InGaN 470 water clear 50 120 110°
KA-2810AQBS-F InGaN 465 water clear 110 250 110°
KA-2810AQBS-G InGaN 465 water clear 180 350 110°
KA-4008SURSK AlGaInP 630 water clear 110 300 120° 4.0mm x 0.8mm Right Angle
KA-4008SESK AlGaInP 601 water clear 110 350 120°
KA-4008SYSK AlGaInP 590 water clear 70 250 120°
KA-4008ZGS InGaN 525 water clear 280 600 120°
KA-4008ZGS-E InGaN 525 water clear 650 1200 120°
KA-4008ZGS-G InGaN 525 water clear 900 1400 120°
KA-4008QBS-D InGaN 470 water clear 50 100 120°
KA-4008QBS-F InGaN 465 water clear 110 250 120°
KA-4008QBS-G InGaN 465 water clear 180 300 120°
KA-4040SURCKT AlGaInP 630 water clear 70 250 90° 4.0mm x 4.0mm Right Angle
KA-4040SECKT AlGaInP 601 water clear 110 400 90°
KA-4040SYCKT AlGaInP 590 water clear 70 250 90°
KA-4040MGCT AlGaInP 570 water clear 50 100 90°
KA-4040CGCKT AlGaInP 570 water clear 36 70 90°
KA-4040ZGCT InGaN 525 water clear 380 600 90°
KA-4040ZGCT-E InGaN 525 water clear 480 1300 90°
KA-4040ZGCT-G InGaN 525 water clear 650 1500 90°
KA-4040QBCT-D InGaN 470 water clear 70 150 90°
KA-4040QBCT-F InGaN 465 water clear 110 220 90°
KA-4040QBCT-G InGaN 465 water clear 180 300 90°
Units : mm(inch)
Tolerance : ±0.25(0.01)
Units : mm(inch)
Tolerance : ±0.1(0.004)
KA-4008
KA-4040
RIGHT ANGLE SMD LED
KA-2810A
Units : mm(inch)
Tolerance : ±0.1(0.004)
SMD LED
18
SMD LED
19
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KPTB-1612ESGC
GaAsP/GaP 625
water clear
4 15
120°
1.6mm x 1.25mm x 0.65mm (0605 Bi-Color)
GaP 568 4 15
KPTB-1612SURKCGKC
AlGaInP 630
water clear
70 220
120°
AlGaInP 570 18 50
KPTB-1612SURKQBDC
AlGaInP 630
water clear
70 220
120°
InGaN 470 36 90
KPTB-1612SYKCGKC
AlGaInP 590
water clear
50 150
120°
AlGaInP 570 18 50
KPTB-1612QBDSEKC
InGaN 470
water clear
36 90
120°
AlGaInP 601 70 240
KPTB-1615ESGC
GaAsP/GaP 625
water clear
4 15
120°
1.6mm x 1.5mm x 0.7mm (0606 Bi-Color)
GaP 568 4 15
KPTB-1615SURKSGC
AlGaInP 630
water clear
70 220
120°
GaP 568 4 15
KPTB-1615SURKCGKC
AlGaInP 630
water clear
70 220
120°
AlGaInP 570 18 50
KPTB-1615SURKQBDC
AlGaInP 630
water clear
70 220
120°
InGaN 470 36 90
KPTB-1615YSGC
GaAsP/GaP 588
water clear
2.6 8
120°
GaP 568 4 15
KPTB-1615SYKCGKC
AlGaInP 590
water clear
50 150
120°
AlGaInP 570 18 50
KPTB-1615SGNC
GaP 568
water clear
4 15
120°
GaAsP/GaP 610 4 15
KPHBM-2012SURKCGKC
AlGaInP 630
water clear
70 220
120°
2.0mm x 1.25mm x 0.45mm (Bi-Color)
AlGaInP 570 18 50
KPHBM-2012CGKSEKC
AlGaInP 570
water clear
18 50
120°
AlGaInP 601 110 250
KPHBM-2012QBDSURKC
InGaN 470
water clear
36 90
120°
AlGaInP 630 70 220
KPHBM-2012QBDCGKC
InGaN 470
water clear
36 90
120°
AlGaInP 570 18 50
NOTE:
1.KP series custom-made is available upon request.
MULTI-COLOR SMD LED
KPTB-1612
KPTB-1615
KPHBM-2012
Units : mm(inch)
Tolerance : ±0.2(0.008)
Units : mm(inch)
Tolerance : ±0.1(0.004)
Units : mm(inch)
Tolerance : ±0.2(0.008)
SMD LED
20
SMD LED
21
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KPBVA-3010ESGC
GaAsP/GaP 625
water clear
7 15
140°
3.0mm x 1.0mm x 2.0mm (1104 Right Angle, Bi-Color)
GaP 568 7 15
KPBVA-3010SRSGC-PRV
GaAlAs 640
water clear
50 140
140°
GaP 568 7 20
KPBVA-3010SURKSGC
AlGaInP 630
water clear
110 300
140°
GaP 568 7 15
KPBVA-3010SURKMGKC
AlGaInP 630
water clear
110 300
140°
AlGaInP 570 36 80
KPBVA-3010SURKQBDC
AlGaInP 630
water clear
110 300
140°
InGaN 470 36 90
KPBVA-3010YSGC
GaAsP/GaP 588
water clear
2.6 8
140°
GaP 568 7 15
KPBVA-3010SYKCGKC
AlGaInP 590
water clear
50 150
140°
AlGaInP 570 18 50
KM-23ESGW
GaAsP/GaP 625
white
diffused
4 15
140°
SOT-23 Surface Mount LED Lamp (3mm x 1.3mm)
GaP 568 4 15
KM-23ESGC
GaAsP/GaP 625
water clear
4 15
140°
GaP 568 4 15
KP-23ESGC
GaAsP/GaP 625
water clear
7 20
120°
3.0mm x 2.4mm x 1.05mm
GaP 568 7 20
KP-23YSGC
GaAsP/GaP 588
water clear
2.6 8
120°
GaP 568 7 20
KPBVA-3010
Units : mm(inch)
Tolerance : ±0.15(0.006)
Units : mm(inch)
Tolerance : ±0.25(0.01)
Units : mm(inch)
Tolerance : ±0.2(0.008)
KM-23ESG
KP-23xxx
MULTI-COLOR SMD LED
NOTE:
1.KP series custom-made is available upon request.
SMD LED
20
SMD LED
21
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KPB-3025ESGC GaAsP/GaP 625
water clear 4 15 120°
3.0mm x 2.5mm x 1.1mm (1109 Bi-Color)
GaP 568 4 15
KPB-3025EYC GaAsP/GaP 625
water clear 4 15 120°
GaAsP/GaP 588 2.6 8
KPB-3025SRSGC-PRV GaAlAs 640
water clear 36 100 120°
GaP 568 4 15
KPB-3025SRCGKC-PRV GaAlAs 640
water clear 36 100 120°
AlGaInP 570 18 50
KPB-3025NSGC GaAsP/GaP 610
water clear 4 15 120°
GaP 568 4 15
KPB-3025SURKCGKC AlGaInP 630
water clear 70 220 120°
AlGaInP 570 18 50
KPB-3025YSGC GaAsP/GaP 588
water clear 2.6 8 120°
GaP 568 4 15
KPB-3025QBDSYKC InGaN 470
water clear 36 80 120°
AlGaInP 590 50 200
KPBL-3025ESGC
GaAsP/GaP 625
water clear
7 20
100°
3.0mm x 2.5mm x 1.4mm (1109 Bi-Color)
GaP 568 7 20
KPBL-3025EYC
GaAsP/GaP 625
water clear
7 20
100°
GaAsP/GaP 588 4 15
KPBL-3025SRSGC-PRV
GaAlAs 640
water clear
36 100
100°
GaP 568 7 20
KPBL-3025NSGC
GaAsP/GaP 610
water clear
7 20
100°
GaP 568 7 20
KPBL-3025SURKCGKC
AlGaInP 630
water clear
180 500
100°
AlGaInP 570 50 150
KPBL-3025YSGC
GaAsP/GaP 588
water clear
4 15
100°
GaP 568 7 20
KPBL-3025QBDSYKC
InGaN 470
water clear
50 180
100°
AlGaInP 590 70 150
KPBD-3224ESGC
GaAsP/GaP 625
water clear
18 60
20°
3.2mm x 2.4mm x 2.4mm (Dome Lens)
GaP 568 10 60
KPBD-3224SURKSGC
AlGaInP 630
water clear
380 1200
20°
GaP 568 10 60
KPBD-3224SURKCGKC
AlGaInP 630
water clear
380 1200
20°
AlGaInP 570 110 300
KPBD-3224YSGC
GaAsP/GaP 588
water clear
4 15
20°
GaP 568 10 60
KPBD-3224SYKCGKC
AlGaInP 590
water clear
110 500
20°
AlGaInP 570 110 300
Units : mm(inch)
Tolerance : ±0.2(0.008)
KPB-3025
NOTE:
1.KP series custom-made is available upon request.
Units : mm(inch)
Tolerance : ±0.2(0.008)
KPBL-3025
MULTI-COLOR SMD LED
Units : mm(inch)
Tolerance : ±0.1(0.004)
KPBD-3224
SMD LED
22
SMD LED
23
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@30mA *50mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KAAF-5060QBDSURKZGCT
InGaN 470
water clear
110 250
100°
5.0mm x 6.0 mm x 2.3mm
AlGaInP 630 *180 *350
InGaN 525 280 650
KAAF-5060QBFSEEZGCT
InGaN 465
water clear
180 350
100°
AlGaInP 621 *650 *1000
InGaN 525 280 650
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KA-2735ESGCT
GaAsP/GaP 625
water clear
7 30
120°
2.7mm x 3.5mm (Bi-Color)
GaP 568 7 30
KA-2735SURKMGCT
AlGaInP 630
water clear
70 200
120°
AlGaInP 570 50 90
KAA-3528SURKSYKCT
AlGaInP 630
water clear
110 350
120°
3.5mm x 2.8mm
AlGaInP 590 70 250
KAA-3528SURKCGKCT
AlGaInP 630
water clear
110 350
120°
AlGaInP 570 36 100
KAA-3528SURKZGQBDCT
AlGaInP 630
water clear
110 350
120°
InGaN 525 380 600
InGaN 470 36 80
Units : mm(inch)
Tolerance : ±0.25(0.01)
KA-2735
Units : mm(inch)
Tolerance : ±0.25(0.01)
KAA-3528
MULTI-COLOR SMD LED
Units : mm(inch)
Tolerance : ±0.25(0.01)
KAAF-5060
SMD LED
22
SMD LED
23
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KM2520SURCK03 AlGaInP 630 water clear 900 2400 20° Subminiature Solid State Lamps
Gull Wing Lead
KM2520SECK03 AlGaInP 601 water clear 900 2500 20°
KM2520SYCK03 AlGaInP 590 water clear 900 2200 20°
KM2520MGC03 AlGaInP 570 water clear 380 900 20°
KM2520CGCK03 AlGaInP 570 water clear 280 700 20°
KM2520ZGC03 InGaN 525 water clear 1200 2500 20°
KM2520ZGC-E03 InGaN 525 water clear 2200 4000 20°
KM2520ZGC-G03 InGaN 525 water clear 2800 5000 20°
KM2520QBC-D03 InGaN 470 water clear 180 500 20°
KM2520QBC-F03 InGaN 465 water clear 480 850 20°
KM2520QBC-G03 InGaN 465 water clear 650 1300 20°
KM2520SURCK08 AlGaInP 630 water clear 900 2400 20° Subminiature Solid State Lamps
Yoke Lead
KM2520SECK08 AlGaInP 601 water clear 900 2500 20°
KM2520SYCK08 AlGaInP 590 water clear 900 2200 20°
KM2520MGC08 AlGaInP 570 water clear 380 900 20°
KM2520CGCK08 AlGaInP 570 water clear 280 700 20°
KM2520ZGC08 InGaN 525 water clear 1200 2500 20°
KM2520ZGC-E08 InGaN 525 water clear 2200 4000 20°
KM2520ZGC-G08 InGaN 525 water clear 2800 5000 20°
KM2520QBC-D08 InGaN 470 water clear 180 500 20°
KM2520QBC-F08 InGaN 465 water clear 480 850 20°
KM2520QBC-G08 InGaN 465 water clear 650 1300 20°
KM2520SURCK09 AlGaInP 630 water clear 900 2400 20° Subminiature Solid State Lamps
Z-Bend Lead
KM2520SECK09 AlGaInP 601 water clear 900 2500 20°
KM2520SYCK09 AlGaInP 590 water clear 900 2200 20°
KM2520MGC09 AlGaInP 570 water clear 380 900 20°
KM2520CGCK09 AlGaInP 570 water clear 280 700 20°
KM2520ZGC09 InGaN 525 water clear 1200 2500 20°
KM2520ZGC-E09 InGaN 525 water clear 2200 4000 20°
KM2520ZGC-G09 InGaN 525 water clear 2800 5000 20°
KM2520QBC-D09 InGaN 470 water clear 180 500 20°
KM2520QBC-F09 InGaN 465 water clear 480 850 20°
KM2520QBC-G09 InGaN 465 water clear 650 1300 20°
Units : mm(inch)
Tolerance : ±0.25(0.01)
Units : mm(inch)
Tolerance : 0.25(0.01)
Units : mm(inch)
Tolerance : ±0.25(0.01)
KM2520xxx03
KM2520xxx08
KM2520xxx09
SUBMINIATURE SMD LED
SMD LED
24
SMD LED
25
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KM-27SURCK-03 AlGaInP 630 water clear 900 2400 20° Subminiature Solid State Lamps
Gull Wing Lead
KM-27SECK-03 AlGaInP 601 water clear 900 2500 20°
KM-27SYCK-03 AlGaInP 590 water clear 900 2200 20°
KM-27MGC-03 AlGaInP 570 water clear 380 900 20°
KM-27CGCK-03 AlGaInP 570 water clear 280 700 20°
KM-27ZGC-03 InGaN 525 water clear 1200 2500 20°
KM-27ZGC-E-03 InGaN 525 water clear 2200 4000 20°
KM-27ZGC-G-03 InGaN 525 water clear 2800 5000 20°
KM-27QBC-D-03 InGaN 470 water clear 180 500 20°
KM-27QBC-F-03 InGaN 465 water clear 480 850 20°
KM-27QBC-G-03 InGaN 465 water clear 650 1300 20°
KM-27SURCK-09 AlGaInP 630 water clear 900 2400 20° Subminiature Solid State Lamps
Z-Bend Lead
KM-27SECK-09 AlGaInP 601 water clear 900 2500 20°
KM-27SYCK-09 AlGaInP 590 water clear 900 2200 20°
KM-27MGC-09 AlGaInP 570 water clear 380 900 20°
KM-27CGCK-09 AlGaInP 570 water clear 280 700 20°
KM-27ZGC-09 InGaN 525 water clear 1200 2500 20°
KM-27ZGC-E-09 InGaN 525 water clear 2200 4000 20°
KM-27ZGC-G-09 InGaN 525 water clear 2800 5000 20°
KM-27QBC-D-09 InGaN 470 water clear 180 500 20°
KM-27QBC-F-09 InGaN 465 water clear 480 850 20°
KM-27QBC-G-09 InGaN 465 water clear 650 1300 20°
Units : mm(inch)
Tolerance : ±0.25(0.01)
Units : mm(inch)
Tolerance : ±0.25(0.01)
KM-27-03
SUBMINIATURE SMD LED
KM-27-09
SMD LED
24
SMD LED
25
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KPTR-3216SURCK AlGaInP 630 water clear 70 220 120° 3.2mm x 1.6mm x 1.05mm (1206 Reverse Mount)
KPTR-3216SECK AlGaInP 601 water clear 70 240 120°
KPTR-3216SYCK AlGaInP 590 water clear 50 150 120°
KPTR-3216MGC AlGaInP 570 water clear 36 70 120°
KPTR-3216CGCK AlGaInP 570 water clear 10 50 120°
KPTR-3216ZGC InGaN 525 water clear 110 300 120°
KPTR-3216ZGC-E InGaN 525 water clear 280 650 120°
KPTR-3216ZGC-G InGaN 525 water clear 380 700 120°
KPTR-3216QBC-D InGaN 470 water clear 36 100 120°
KPTR-3216QBC-F InGaN 465 water clear 50 150 120°
KPTR-3216QBC-G InGaN 465 water clear 70 180 120°
PART NUMBER MATERIAL lD
(nm) LENS TYPE
Iv (mcd)
@20mA
VIEWING
ANGLE DIMENSION
MIN. TYP. 2q1/2
KM-23ID-F GaAsP/GaP 625 red diffused 4 12 140° SOT-23 Surface Mount LED Lamp (3mm x 1.3mm)
KM-23EC-F GaAsP/GaP 625 water clear 4 15 140°
KM-23SRD-F GaAlAs 640 red diffused 36 70 140°
KM-23SRC-F GaAlAs 640 water clear 36 90 140°
KM-23YD-F GaAsP/GaP 588 yellow diffused 2.6 8.5 140°
KM-23YC-F GaAsP/GaP 588 water clear 2.6 10 140°
KM-23SYD-F AlGaInP 590 yellow diffused 50 100 140°
KM-23SYC-F AlGaInP 590 water clear 50 150 140°
KM-23SGD-F GaP 568 green diffused 2.6 8 140°
KM-23SGC-F GaP 568 water clear 4 15 140°
KM-23CGCK-F AlGaInP 570 water clear 18 50 140°
KM-23ZGC-F InGaN 525 water clear 70 250 140°
KM-23ZGC-E-F InGaN 525 water clear 110 450 140°
KM-23ZGC-G-F InGaN 525 water clear 280 500 140°
KM-23QBC-D-F InGaN 470 water clear 36 80 140°
KM-23QBC-F-F InGaN 465 water clear 50 100 140°
KM-23QBC-G-F InGaN 465 water clear 70 140 140°
Units : mm(inch)
Tolerance : ±0.2(0.008)
Units : mm(inch)
Tolerance : ±0.25(0.01)
KPTR-3216
KM-23-F
REVERSE MOUNT SMD LED
SOT-23 SMD LED
NOTE:
1.KP series custom-made is available upon request.
26
THROUGH-HOLE LED
27
SMD LED
PART NUMBER DIMENSION
KPS-5130PD7C KPS-5130PD7C 5.12mm x 3mm x 1.1mm
(RGB COLOR SENSOR)
AMBIENT LIGHT SENSOR
COLOR SENSOR
PART NUMBER DIMENSION
KPS-3227SP1C KPS-3227SP1C 3.2mm x 2.7mm x 1.1mm
(AMBIENT LIGHT SENSOR)
ELECTRICAL AND RADIANT CHARACTERISTICS
(TA =25°C,UNLESS OTHERWISE SPECIFIED)
PARAMETER SYMBOL MIN. TYP. MAX. UNIT TEST CONDITION
Collector Emitter Breakdown Voltage BVceo 60 - - V Iceo=100mA
Emitter Collector Breakdown Voltage BVeco 4 - - V Ieco=100mA
Collector Dark Current I D- 10 100 nA VCE=5V EV=0Lx
Angle Of half Sensitivity 2q1/2 - 120 - ° -
Light Current(1) IPH1 -6-mAVCE=5V,Ev=100 Lx[1]
Light Current(2) IPH2 130 - mAVCE=5V,Ev=1000 Lx[1]
Light Current(3) IPH3 - 950 - mAVCE=5V,Ev=1000 Lx[2]
Light Current(4) IPH4 - 420 - mAVCE=5V,Ev=1000 Lx[3]
Saturation Output Voltage Vo 4.5 4.7 - V VCC=5V,EV=1000Lx[1],
RL=75KW
Peak Wavelength lP - 580 - nm -
Response Wavelength l390 - 700 nm >10% Response
Collector Emitter Saturation Voltage VCE(sat) - - 0.4 V IC=10 mA
ELECTRICAL AND RADIANT CHARACTERISTICS
(TA =25°C,UNLESS OTHERWISE SPECIFIED)
PARAMETER SYMBOL CONDITION MIN. TYP. MAX. UNIT
Peak Sensitivity Wavelength lP
Red - 620 -
nmGreen - 550 -
Blue - 470 -
Light Current (1) I L1 100Lux [1]
VR =5V
Red - 0.039 -
mAGreen - 0.042 -
Blue - 0.022 -
Light Current (2) I L2 1000Lux [1]
VR =5V
Red - 0.427 -
VGreen - 0.498 -
Blue - 0.262 -
Diameter of the irradiation
sensitive area D - 2.0 - mm
Irradiation sensitive area per
element A - 0.85 - mm2
Photo sensibility of
the single color areas SMax
l R=620 nm
l G=550 nm
l B=470 nm
-
0.33
0.25
0.18
- A/W
Reverse Dark Current I DVR =5V
-- - 10 nA
Units : mm(inch)
Tolerance : ±0.1(0.004)
Units : mm(inch)
Tolerance : ±0.1(0.004)
KPS-3227SP1C
KPS-5130PD7C
Notes:
1.White Fluorescent light (Color Temperature = 6200K) is used as light source.
2.Illuminance by CIE standard illuminant-A/2856K,incandescet lamp.
3.Sunlight (Color Temperature = 4600K) is used as light source.
Note:
1.White uorescent light (Color Temperature = 6500K) is used as light source.