FM809/810 3-Pin C Supervisor Circuits General Description 140ms power-on RESET delay (minimum) RESET operation guaranteed to 1.0V Supply current only 2A No external components Operating Range - -40C to +105C (SOT23) - -40C to +85C (SC70) SOT23-3 and SC70-3 packages The FM809/810 are supervisor circuits that monitor power supply or other system voltages and issue reset pulse whenever the voltage being monitored is out of tolerance. Once asserted, the reset pulse is guaranteed to be valid for a minimum of 140ms (256ms typical). FM809xx offers active low push-pull type of reset while FM810xx offers active high push-pull type. Several threshold voltages are offered to accommodate 5.0V, 3.3V, 3.0V and 2.7V system voltages. The low supply current (typically 2 A)recommends FM809/810 devices for portable designs or wherever power saving is primary. Applications These devices are offered in space saving 3-pin SOT23 and SC70 packages. Features VTH voltages of 4.63V, 4.38V, 4.00V, 3.08V, 2.93V and 2.63V RESET (FM809) or RESET (FM810) output Microcontrollers and Microprocessors Appliances Power-Supply Monitoring Portable Equipment Automotive Systems Typical Operating Circuit VCC VCC FM809 C RESET RESET I/P GND GND Connection Diagram GND 1 3 RESET (809) or RESET (810) VCC 2 FM809/810 SOT23-3 & SC70-3Packages (c)2002 Fairchild Semiconductor Corporation FM809/810 Rev. F 1 www.fairchildsemi.com FM809/810 3-Pin C Supervisor Circuits October 2002 ESD Rating Human Body Model Machine Model Rate of Rise of VCC Continuous Power Dissipation (TA = +70C) SOT23-3 (derate 4mW/C above +70C) Operating Temperature Range Storage Temperature Range Lead Temperature (soldering, 10s) -0.3V to +6.0V -0.3V to (VCC + 0.3V) 20mA 20mA >2KV >200KV 100V/s 320mW -40C to +105C -65C to +150C +300C These are stress ratings only, and functional operation is not implied for these levels or beyond. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Electrical Characteristics SOT23 Package (TA = 25C unless otherwise noted) VCC = full range, as noted under conditions. See Note 1. Parameter Symbol Operating Voltage VCC Supply Current ICC Reset Threshold VTH Conditions Min TA = 0C to +70C 1.0 TA = -40C to 105C 1.1 10 TA = -40C to 105C, VCC < 3.6V FM809R/S/T 2 6 FM8xxL TA = -40C to +105C 4.40 4.63 4.86 FM8xxM TA = -40C to +105C 4.18 4.38 4.52 FM8xxJ TA = -40C to +105C 3.90 4.00 4.18 FM8xxT TA = -40C to +105C 2.97 3.08 3.19 FM8xxS TA = -40C to +105C 2.79 2.93 3.00 FM8xxR TA = -40C to +105C 2.49 2.63 2.70 30 VCC = VTH to (VTH - 100mV) Reset Active Timout Period TA = -40C to +105C VOL VOH FM810 Output Low (RESET) VOL VOH A V ppm/C 10 15 s 256 560 ms VCC = VTH(min), ISINK = 1.2mA, FM809R/S/T 0.3 V VCC = VTH(min), ISINK = 3.2mA, FM809J/L/M 0.4 140 VCC = < 1.0V, ISINK = 50A FM809 Output High (RESET) V 5.5 5 VCC to Reset Delay (Note 2) FM810 Output High (RESET) 5.5 TA = -40C to 105C, VCC < 5.5V FM809J/L/M Reset Threshold Tempco FM809 Output Low (RESET) Typ (Note 3) Max Units 0.3 VCC > VTH(max), ISOURCE = 500A (R/S/T) 0.8VCC VCC > VTH(max), ISOURCE = 800A (J/M/L) VCC - 1.5V V VCC = VTH(max), ISINK = 1.2mA, FM810R/S/T 0.3 VCC = VTH(max), ISINK = 3.2mA, FM810J/L/M 0.4 1.8V < VCC < VTH(min), ISOURCE = 150A 0.8VCC V V Note 1: Testing in production is 25C only. VCC = 5V for FM8xxL/M/J, VCC = 3.3V for FM8xxT/S and VCC = 3V for FM8xxR. Limits over temperature are guaranteed by design. Note 2: RESET output is for FM809. RESET output is for FM810. Note 3: Typical values are at 25C. Note 4: Recommended minimum slew rate for the VCC rampup is 200mV/sec in the 0 to 2V range for the device to function properly. 2 FM809/810 Rev. F www.fairchildsemi.com FM809/810 3-Pin C Supervisor Circuits Absolute Maximum Ratings Voltage on any terminal relative to GND VCC RESET, RESET Input Current Output Current: RESET, RESET Voltage on any terminal relative to GND VCC RESET, RESET Input Current Output Current: RESET, RESET ESD Rating Human Body model Machine model Rate of Rise of VCC Continuous Power Dissipation (TA = +70C) SC70-3 Operating Temperature Range Storage Temperature Range Lead Temperature (soldering, 10s) -0.3V to +6.0V -0.3V to (VCC + 0.3V) 20mA 20mA 1.5KV >200KV 100V/s 174mW -40C to +85C -65C to +150C +300C These are stress ratings only, and functional operation is not implied for these levels or beyond. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Electrical Characteristics SC70 Package (TA = 25C unless otherwise noted) VCC = full range, as noted under conditions. See Note 1. Parameter Symbol Operating Voltage VCC Supply Current ICC Reset Threshold VTH Conditions Min TA = 0C to +70C 1.4 TA = -40C to 85C 1.6 TA = -40C to 85C, VCC < 5.5V FM809J/L/M 5.5 15 6 10 FM8xxL TA = -40C to +85C 4.40 4.63 4.86 FM8xxM TA = -40C to +85C 4.18 4.38 4.52 FM8xxJ TA = -40C to +85C 3.90 4.00 4.18 FM8xxT TA = -40C to +85C 2.97 3.08 3.19 FM8xxS TA = -40C to +85C 2.79 2.93 3.00 FM8xxR TA = -40C to +85C 2.49 2.63 2.70 Reset Threshold Tempco 30 VCC to Reset Delay (Note 2) VCC = VTH to (VTH - 100mV) Reset Active Timout Period TA = -40C to +85C VOL V 5.5 9 TA = -40C to 85C, VCC < 3.6V FM809R/S/T FM809 Output Low (RESET) Typ (Note 3) Max Units A V ppm/C 10 15 s 256 560 ms VCC = VTH(min), ISINK = 1.2mA, FM809R/S/T 0.35 V VCC = VTH(min), ISINK = 3.2mA, FM809J/L/M 0.4 100 VCC = < 1.0V, ISINK = 50A FM809 Output High (RESET) VOH FM810 Output Low (RESET) VOL VCC = VTH(max), ISINK = 1.2mA, FM810R/S/T FM810 Output High (RESET) VOH 1.8V < VCC < VTH(min), ISOURCE = 150A 0.3 VCC > VTH(max), ISOURCE = 500A (R/S/T) 0.8VCC VCC > VTH(max), ISOURCE = 800A (J/M/L) VCC - 1.5V V 0.35 VCC = VTH(max), ISINK = 3.2mA, FM810J/L/M V 0.4 0.8VCC V Note 1: Testing in production is 25C only. VCC = 5V for FM8xxL/M/J, VCC = 3.3V for FM8xxT/S and VCC = 3V for FM8xxR. Limits over temperature are guaranteed by design. Note 2: RESET output is for FM809. RESET output is for FM810. Note 3: Typical values are at 25C. 3 FM809/810 Rev. F www.fairchildsemi.com FM809/810 3-Pin C Supervisor Circuits Absolute Maximum Ratings Pin Number Name 1 GND 2 RESET* 3 VCC Function GROUND RESET (RESET) remains LOW (HIGH) while VCC is below VTH, and for at least 140ms after VCC rises above VTH. * with overbar, FM809 (RESET); without, FM810 (RESET). Circuit Timing (e.g.: FM809) INPUT 5V VTH 1V GND OUTPUT 5V VTH 1V GND 140ms When operating properly with 5V in (for example), VOUT will also be about 5V. When VIN starts to fall, VOUT will follow it down as shown. When VIN drops below VTH, VOUT drops to ground ("issues a RESET") and stays there unless VIN also falls below its minimum operating voltage, approx. 1V. At this point, the supervisor loses control, and its output may rise, only to again follow VIN down to the ground. When VIN begins to rise, VOUT follows it until 1.0V or so is reached, whereupon the device regains control, VOUT is pulled to ground, etc. When VIN rises above VTH, VOUT comes out of RESET 140 ms later. If it is required that a lower value than GND + 1.0V is needed on RESET signal during VCC 1V, a 100K resistor may be used on the device output (to GND for the FM809, to VCC for the FM810). 4 FM809/810 Rev. F www.fairchildsemi.com FM809/810 3-Pin C Supervisor Circuits Pin Descriptions Part Number Top Marking RESET Threshold (V) Output Type Package Type Packing Method FM809LS3X 09L 4.63 Push-Pull, active LOW 3-Pin, SOT23 3000 units in T&R FM809MS3X 09M 4.38 Push-Pull, active LOW 3-Pin, SOT23 3000 units in T&R FM809JS3X 09J 4.00 Push-Pull, active LOW 3-Pin, SOT23 3000 units in T&R FM809TS3X 09T 3.08 Push-Pull, active LOW 3-Pin, SOT23 3000 units in T&R FM809SS3X 09S 2.93 Push-Pull, active LOW 3-Pin, SOT23 3000 units in T&R FM809RS3X 09R 2.63 Push-Pull, active LOW 3-Pin, SOT23 3000 units in T&R FM809LP3X VLY 4.63 Push-Pull, active LOW 3-Pin, SC70 3000 units in T&R FM809MP3X VMY 4.38 Push-Pull, active LOW 3-Pin, SC70 3000 units in T&R FM809JP3X VJY 4.00 Push-Pull, active LOW 3-Pin, SC70 3000 units in T&R FM809TP3X VTY 3.08 Push-Pull, active LOW 3-Pin, SC70 3000 units in T&R FM809SP3X VSY 2.93 Push-Pull, active LOW 3-Pin, SC70 3000 units in T&R FM809RP3X VRY 2.63 Push-Pull, active LOW 3-Pin, SC70 3000 units in T&R Note 4: Devices listed above feature 250ms typical Reset Pulse width. Consult Fairchild sales for other reset pulse width options. 5 FM809/810 Rev. F www.fairchildsemi.com FM809/810 3-Pin C Supervisor Circuits Ordering Information (FM809) Part Number Top Marking RESET Threshold (V) Output Type Package Type Packing Method FM810LS3X 10L 4.63 Push-Pull, active HIGH 3-Pin, SOT23 3000 units in T&R FM810MS3X 10M 4.38 Push-Pull, active HIGH 3-Pin, SOT23 3000 units in T&R FM810JS3X 10J 4.00 Push-Pull, active HIGH 3-Pin, SOT23 3000 units in T&R FM810TS3X 10T 3.08 Push-Pull, active HIGH 3-Pin, SOT23 3000 units in T&R FM810SS3X 10S 2.93 Push-Pull, active HIGH 3-Pin, SOT23 3000 units in T&R FM810RS3X 10R 2.63 Push-Pull, active HIGH 3-Pin, SOT23 3000 units in T&R FM810LP3X ZLY 4.63 Push-Pull, active HIGH 3-Pin, SC70 3000 units in T&R FM810MP3X ZMY 4.38 Push-Pull, active HIGH 3-Pin, SC70 3000 units in T&R FM810JP3X ZJY 4.00 Push-Pull, active HIGH 3-Pin, SC70 3000 units in T&R FM810TP3X ZTY 3.08 Push-Pull, active HIGH 3-Pin, SC70 3000 units in T&R FM810SP3X ZSY 2.93 Push-Pull, active HIGH 3-Pin, SC70 3000 units in T&R FM810RP3X ZRY 2.63 Push-Pull, active HIGH 3-Pin, SC70 3000 units in T&R Note 5: Devices listed above feature 250ms typical Reset Pulse width. Consult Fairchild sales for other reset pulse width options. 6 FM809/810 Rev. F www.fairchildsemi.com FM809/810 3-Pin C Supervisor Circuits Ordering Information (FM810) FM809/810 3-Pin C Supervisor Circuits Physical Dimensions inches (millimeters) unless otherwise noted 0.021 0.015 0.055 0.047 0.098 0.083 0.120 0.105 0.0059 0.0035 0.040 0.031 0.079 0.071 0-8 0.010 0.005 0.004 0.001 0.76 2.29 PKG CL 0.76 0.95 LAND PATTERN RECOMMENDATION SOT-23 Package Dimensions FS Pkg Code AU 7 FM809/810 Rev. F www.fairchildsemi.com FM809/810 3-Pin C Supervisor Circuits Physical Dimensions inches (millimeters) unless otherwise noted .087 (2.2) .071 (1.8) .053 (1.35) .045 (1.15) .087 (2.2) .079 (2.0) .009 (.23) .005 (.13) .043 (1.1) .032 (.80) .004 (.10) .010 (.25) .004 (.10) .016 (.40) .012 (.30) .026 (.65) .018 (.45) .006 (.15) .052 (1.3) 0.65 1.80 0.65 0.6 0.5 Land Pattern Recommendation SC70 Package Dimensions Life Support Policy Fairchild's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President of Fairchild Semiconductor Corporation. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. Fairchild Semiconductor Americas Customer Response Center Tel. 1-888-522-5372 Fairchild Semiconductor Europe Fax: +44 (0) 1793-856858 Deutsch Tel: +49 (0) 8141-6102-0 English Tel: +44 (0) 1793-856856 Francais Tel: +33 (0) 1-6930-3696 Italiano Tel: +39 (0) 2-249111-1 Fairchild Semiconductor Hong Kong 8/F, Room 808, Empire Centre 68 Mody Road, Tsimshatsui East Kowloon. Hong Kong Tel; +852-2722-8338 Fax: +852-2722-8383 8 FM809/810 Rev. F 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Fairchild Semiconductor Japan Ltd. 4F, Natsume Bldg. 2-18-6, Yushima, Bunkyo-ku Tokyo, 113-0034 Japan Tel: 81-3-3818-8840 Fax: 81-3-3818-8841 www.fairchildsemi.com