IECQ-CECC QC 88000-C002 COMPONENT ISSUE 1 SPECIFICATION March 2007 Component Specification For Ceramic Hermetically Sealed High Speed Optocouplers Up-to-date lists and bibliographical references of IEQC-CECC publications may be downloaded from www.iecq.org Further copies of this document may be obtained from: IEC International Electrotechnical Commission Commission Electrotechnique Internationale Box 131, rue de Varembe, CH 1211 Geneva 20, Switzerland For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 (c) 2007 Copyright reserved to Isocom Limited QC 88000-C002: 2007 Page 1 of 12 FOREWORD The IECQ Quality Assessment System for Electronic Components (IECQ) is composed of those member countries of the International Electrotechnical Commission (IEC) who wish to take part in a harmonized system for electronic components of assessed quality. IECQ is also known in some European member countries as IECQ-CECC. The object of the System is to facilitate international trade by the harmonization of the specifications and quality assessment procedures for electronic components, and by the grant of an internationally recognised Mark, or Certificate of Conformity. The components produced or services provided under the system are thereby acceptable in all member countries without further testing. This Component Specification is based upon the requirements of IEC Publication QC 001002-2, and has been prepared by: Isocom Ltd Hutton Close Crowther Industrial Estate Washington Tyne and Wear NE38 0AH Tel: Fax: +44 0191 4166 546 +44 0191 4155 055 and published under the authority of: BSI Product Services Maylands Avenue Hemel Hempstead Hertfordshire HP2 4SQ United Kingdom AMENDMENT RECORD No previous issue. REQUIREMENTS The requirements for IECQ-CECC Component Specifications as detailed in QC 001002-2 Amendment 1 clause 5.4 are satisfied by the following data sheet. It should note that IECQ-CECC are not responsible for manufacturers declarations made in data sheets which fall outside the limits of approved detailed in IECQ-CECC certificates. This Component Specification is intended for use with applicable IECQ-CECC Assessment Specifications. Eg: QC 88000-A001 For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 (c) 2007 Copyright reserved to Isocom Limited QC 88000-C002: 2007 Page 2 of 12 ISOCOM LTD (R) Ceramic Hermetically Sealed High Speed Optocouplers 4N55 CD850 CH380 CS800/801 CSM168-2 CSM168-4 CSM1801 CSM1800 MC800 Features Applications Release to IECQ-CECC Military, high reliability system Hermetically Sealed Medical instruments High Density Packaging Mos, Cmos Applications 1500V DC withstand Test Voltage Logic Interfacing Low Input Requirements Data Transmission High Current Transfer Ratio Power Supply Description These devices are single, dual and quad, hermetically sealed optocouplers. Each channel is composed of a Gallium Arsenide infra-red emitting diode and a silicon phototransistor. Package styles for these devices include 6 pin, 8 pin, 16 pin flat pack, and hybrid 4 pin, with surface mount, butt cut and gull wing options available. The same electrical die, assembly processes and materials are used for each channel of each device shown below. Therefore absolute maximum ratings, recommended operating conditions, electrical specifications and performance characteristics are identical for all units. Any exceptions, due to packaging variations and limitations, are as noted. For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 (c) 2007 Copyright reserved to Isocom Limited QC 88000-C002: 2007 Page 3 of 12 ISOCOM LTD (R) Selection Guide Package Styles and Configuration Options Package 16 pin DIP Lead Style Channels 2 Common Channel Wiring Isocom Part Numbers and Options 4N55 Commercial 4N55/L2 Defense Level 4N55/L2S Space Level Standard Gold Plate Finish Gold Plate Solder Dipped Option 20 Butt Cut/Gold Plate Option 10 Gull Wing/Soldered Option 30 Crew Cut/Gold Plate Option 60 6 Pad LCC 6pin metal Can TO-5 1 8 pin DIP 6 pin Hybrid 16 pin Flat Pack 1/2 1 4 1 CH380 CSM168-2/4 CSM1682/4/L2 CSM1682/4/L2S Gold Plate CSM1800/01 CS800/801 CD850 CS800/801/L2 CD850/L2 CS800/801/L2S CD850/L2S Gold Plate Option 20 Option 10 Option 30 Option 60 MC800 CH380/L2 CH380/L2S Gold Plate Option 20 Option 10 Option 30 Option 60 MC800/L2 CSM1800/01 MC800/L2S CSM1800/01 Gold Plate Gold Plate Functional Diagrams CH380 CS800/801 CD850 1 Channel 1 Channel 2 Channel 4N55 & CSM168-2 2 Channel CSM168-4 CSM1800/01 4 Channel 1 Channel 6 5 1 4 2 3 MC800 1 Channel 5 3 2 7 1 For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 (c) 2007 Copyright reserved to Isocom Limited QC 88000-C002: 2007 Page 4 of 12 ISOCOM LTD (R) Outline Drawings 16 pin DIP, 4 Channel 16 pin Flat Pack, 4 Channel NOTE: DIMENSIONS IN MILLIMETERS 6 pin TO-5, 1 Channel 6 LEADS 0.0175 (0.445) 0.040(1.02) 45. 0 0.32 (8.13) 5 0.037 (0.935) 6 0.022 (5.08) 3 7 2 1 0.5 (12.70) 0.031 (0.787) 0.17 (4.32) For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 (c) 2007 Copyright reserved to Isocom Limited QC 88000-C002: 2007 Page 5 of 12 ISOCOM LTD (R) 8 pin DIP 1 and 2 Channel 6 Terminal LCC Surface Mount, 1 Channel 1.651 6.223 0.635 2.286 5 6 4 1 3 2 1.27 4.318 CSM1800 2.54 R = .2286 1.67 0.762 0.635 Device Marking ISOCOM Manufacturer XXXXXXX Isocom Part Number XXXX Date Code (XX year XX week) For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 (c) 2007 Copyright reserved to Isocom Limited QC 88000-C002: 2007 Page 6 of 12 ISOCOM LTD (R) Hermetic Optocoupler Options Option 10 Description Surface mountable hermetic optocoupler with leads trimmed for butt joint assembly. This option is available on commercial hi-rel product in 8 and 16 pin DIP 20 30 Surface mountable hermetic optocoupler with leads cut and bent for gull wing assembly. This option is available on commercial and hi-rel product in 8 and 16 pin DIP. 60 Surface mountable hermetic optocoupler with leads trimmed for butt joint assembly. This option is available on commercial hi-rel product in 8 and 16 pin DIP For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 (c) 2007 Copyright reserved to Isocom Limited QC 88000-C002: 2007 Page 7 of 12 ISOCOM LTD (R) Absolute Maximum Ratings Storage Temperature Operating Temperature -65C to +150C -55C to +125C Input Diode Peak Forward Current Average Forward Current Reverse Voltage Power Dissipation 40mA 20mA 5V 36mW 1 mS duration Derate linearly above 100C at 1.4W/C for CH380 and CS800/801 Output Detector Supply Voltage Average Current Peak Current Voltage Power Dissipation -0.5 to 20V 8mA 16mA -0.5 to 20V 40mW 50mW Emitter-Base Reverse Voltage Base Current 3V 5mA VCC IO IO VO For CH380 and CS800/801 Derate linearly above 100C at 1.4W/C for CD850, CSM6530 and 4N55 BVEBO IB Single Channel Schematic For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 (c) 2007 Copyright reserved to Isocom Limited QC 88000-C002: 2007 Page 8 of 12 ISOCOM LTD (R) Electrical Characteristics TA = -55C to +125C U.O.S. All typical values at VCC = 5V, TA = 25C (each channel where appropriate). Parameter Current Transfer Ratio (See notes 1 & 2) Symbol hf(CTR) Test Conditions VCC = 4.5V, VO = 0.4V,IF = 16mA, Logic Low Output Voltage VOL VCC = 4.5V, VO = 0.5V, IF = 16mA VCC = 4.5V, IF = 16mA IO = 1.44mA Logic High Current (See note 1) IOH Device CS801 CD850 CD850 Output IF1 = 0, IF2 = 20mA VO = VCC = 18V IF1 = F2 = 20mA, VO = VCC = 15 Logic Low Supply Current (See note 1) ICCL Min 9 15 9 - Type 20 17 0.3 Max - Units % 0.4 V - 0.3 30 0.5 250 A - 30 200 A - 0.4 400 10 A CD850 CSM1800 VCC = 18V, IF1 = IF2 = 20Ma VCC = 18V, IF1 = 20Ma CS800/1 VCC = 15V IF1 = 16Ma IF2 =0 CH380 CD850 CSM1800 Logic High Supply Current (See note 1) Input Forward Voltage (See note 1) Input Reverse Breakdown (See note 1) Input-Output Insulation Leakage Current (See notes 3 & 9) ICCH VCC = 16VF1 = IF2 =16mA Vcc = 18V, IF = 0mA, IF (other channel) = 20mA VF IF = 20mA - 1.45 1.9 V VBR IR = 10A 3 - - V IIO - - 1.0 A Propagation Delay Time to Logic Low at Output (See note 1) tPHL RH = 45%, TA = 25C, t = 5S VIO = 1500VDC RH = 45%, TA = 25C, t = 5S VIO = 500VDC RL = 8.2K, IF = 16mA, VCC = 5V CL = 50pF - 0.4 2.0 S RL = 1.9K, IF = 16mA, VCC = 5V Propagation Delay Time to Logic High at Output (See note 1) tPLH CH380 CD850 CSM1800 RL = 8.2K, IF = 16mA, VCC = 5V CL = 50pF RL = 1.9K, IF = 16mA, VCC = 5V 2.0 - CD850 CSM1800 2.0 6.0 S 6.0 For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 (c) 2007 Copyright reserved to Isocom Limited QC 88000-C002: 2007 Page 9 of 12 ISOCOM LTD (R) Typical Characteristics TA = 25C Parameter Temperature Coefficient of Forward Voltage Input Capacitance Resistance (Input-Output) Capacitance (InputOutput) Input-Input Insulation Leakage Current Capacitance (Input-Input) Transistor DC Current Gain Small Signal Current Transfer Ratio Common Mode Transient Immunity at Logic Low Level Output Common Mode Transient Immunity at Logic High Level Output Bandwidth Symbol VF TA CIN RI-O CI-O Test Conditions IF = 20mA Notes 1 Min - Type -1.9 Max - Units mV/C f = 1mhz, VF = 0 V1-0 = 500Vdc f = 1MHz 1 1 1&4 - 125 1012 1.0 - pF pF II-I 45% Relative Humidity VH = 500Vdc, t = 5S f = 1MHz VO = 5V, IO = 3mA 5 - 1 - pA 5 1 - 0.6 130 - pF - VCC = 5V, VO = 2V 1 - 20 - % IF = 16mA,RL = 8.2K VCM = 10VP-P VO (max) = 0.8V IF = 0mA,RL = 8.2K VCM = 10VP-P VO (max) = 2.0V RL = 100 1&7 - -1000 - V/S 1&6 - 1000 - V/S 8 - 2 - MHz CI-I hFE IO IF CML CMH BW Notes (Apply typically to 16 pin package) 1. Each channel, where appropriate. 2. Current Transfer ratio is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100%. CTR is known to degrade slightly over the unit's lifetime as a function of input current, temperature, signal duty cycle and system on time. It is recommended that designers allow at least 20-25% guard band for CTR degradation. 3. Measured between pins 1 through 8 shorted together, and pins 9 through 16 shorted together. 4. Measured between each input pair shorted together, and the output pins for that channel shorted together. 5. Measured between pins 3 and 4 shorted together, and pins 7 and 8 shorted together. 6. CMH is the steepest slope (dV/dt) on the leading edge of the common mode pulse, VCM, for which the output will remain in the logic high state (i.e., VO > 2.0V). 7. CML is the steepest slope (dV/dt) on the trailing edge of the common mode pulse, VCM, for which the output will remain in the logic low state (i.e., VO < 0.8V). 8. Bandwidth is the frequency at which the AC output voltage is 3dB below the low frequency asymptote. 9. This is a momentary withstand test, not an operating condition. For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 (c) 2007 Copyright reserved to Isocom Limited QC 88000-C002: 2007 Page 10 of 12 ISOCOM LTD (R) Electrical Characteristics For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 (c) 2007 Copyright reserved to Isocom Limited QC 88000-C002: 2007 Page 11 of 12 ISOCOM LTD (R) For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 (c) 2007 Copyright reserved to Isocom Limited QC 88000-C002: 2007 Page 12 of 12