Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS Product information in this catalog is as of October 2011. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products. Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual specification. Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is available. Please conduct validation and verification of products in actual condition of mounting and operating environment before commercial shipment of the equipment. All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance. Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required. In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. The contents of this catalog are applicable to the products which are purchased from our sales offices or distributors (so called"TAIYO YUDEN' s official sales channel"). It is only applicable to the products purchased from any of TAIYO YUDEN's official sales channel. Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights. Caution for export Certain items in this catalog may require specific procedures for export according to"Foreign Exchange and Foreign Trade Control Law"of Japan,"U.S. Export Administration Regulations", and other applicable regulations. Should you have any question or inquiry on this matter, please contact our sales staff. 12 notice_e-01 CHIP BEAD INDUCTORS FOR POWER LINES (FB SERIES M TYPE) WAVE FEATURES APPLICATIONS Power supply units: Withstand large current allowable current: up to 6A Resistance to high energy High reliability Deals with power line radiated and conducted noise. REFLOW Provides waveform correction of digital signals and high frequency noise countermeasures in various types of digital equipment. Automotive There are several variations of the FBMJ type HS For broadband applications HMFor upper MHz range applications HL For GHz range applications Computer Peripherals Differential transmission line on USB and similar products Mobile devices which require lower power consumption The FBMH type is optimal for circuit designs which require high impedances and large currents to combat radiated noise on power lines, etc. OPERATING TEMP. 40125(Including self-generated heat) ORDERING CODE F B M J FB Type Ferrite bead M Shape Rectangular chip Product characteristics J Standard type H High Impedance type 3 2 1 6 H S 8 0 External Dimensions LxW mm 1608 0603 1.6x0.8 2125 0805 2.0x1.25 2012 0805 2.0x1.25 2016 0806 2.0x1.6 3216 1206 3.2x1.6 3225 1210 3.2x2.5 4516 1806 4.5x1.6 4525 1810 4.5x2.5 4532 1812 4.5x3.2 Material code HS HM HL Refer to impedance curves for material difference 0 T Impedance Tolerance 25% N 30% T Nominal Impedance 330 111 132 Packaging Tape & Reel example Internal code Standard product Blank space 33 110 1300 EXTERNAL DIMENSIONS/STANDARD QUANTITY Standard Quantitypcs Paper Tape Embossed Tape Type L W T e FBMJ1608 0603 1.60.2 0.0630.008 2.00.2 0.0790.008 3.20.3 0.1260.012 4.50.3 0.1770.012 1.60.1 0.0630.004 2.00.2 0.0790.008 2.00.2 0.0790.008 3.20.3 0.1260.012 3.20.3 0.1260.012 4.50.3 0.1770.012 4.50.4 0.1770.016 4.50.4 0.1770.016 0.80.2 0.0310.008 1.250.2 0.0490.008 1.60.2 0.0630.008 1.60.2 0.0630.008 0.80.1 0.0310.004 1.250.2 0.0490.008 1.60.2 0.0630.008 1.60.2 0.0630.008 2.50.3 0.0980.012 1.60.2 0.0630.008 2.50.3 0.0980.012 3.20.3 0.1260.012 0.80.2 0.0310.008 0.850.2 0.0330.008 1.10.2 0.0430.008 1.10.2 0.0430.008 0.80.1 0.0310.004 0.850.2 0.0330.008 1.60.2 0.0630.008 1.60.2 0.0630.008 2.50.3 0.0980.012 1.60.2 0.0630.008 2.50.3 0.0980.012 3.20.3 0.1260.012 0.30.2 0.0120.008 0.50.3 0.0200.012 0.50.3 0.0200.012 0.50.3 0.0200.012 0.30.15 0.0120.006 0.50.3 0.0200.012 0.50.3 0.0200.012 0.50.3 0.0200.012 0.50.3 0.0200.012 0.50.3 0.0200.012 0.90.6 0.0350.024 0.90.6 0.0350.024 FBMJ2125 0805 FBMJ3216 1206 FBMJ4516 1806 FBMH1608 0603 FBMH2012 0805 FBMH2016 0806 FBMH3216 1206 FBMH3225 1210 FBMH4516 1806 FBMH4525 1810 FBMH4532 1812 4000 4000 2000 2000 4000 4000 2000 2000 1000 2000 1000 2000 Unitmm inch Recommended Land Pattern Dimensions Parts Number C B A A FB MJ1608 type FB MJ2125 type FB MJ3216 type FB MJ4516 type FB MH1608 type FB MH2012 type Dimensions (mm) A B C 1.0 1.0 1.0 1.2 1.65 1.4 2.2 2.0 1.4 3.5 2.0 1.75 1.0 1.0 1.0 1.2 1.65 1.4 Parts Number FB MH2016 type FB MH3216 type FB MH4516 type FB MH3225 type FB MH4525 type FB MH4532 type Dimensions (mm) A B C 1.4 1.2 1.4 2.2 2.0 2.0 1.75 3.5 2.0 1.4 2.2 2.9 1.75 3.5 2.9 1.75 3.5 3.7 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 144 12 chipbeads01_e-01 AVAILABLE MATERIALS Standard Type FBMJ1608 FBMJ2125 HS-type I max=4A, 6A HM-type HS-type I max=4A, 6A HM-type I max=4A, 6A I max=4A, 6A FBMJ3216 HL-type HM-type I max=4A, 6A I max=4A, 6A HL-type 70 60 50 40 30 20 10 0 I max=4A FBMJ4516 HS-type HM-type HL-type 100 90 80 70 60 50 40 30 20 10 0 I max=4A, 6A I max=4A, 6A I max=3.5A High impedance Type FBMH1608 FBMH20 HM-type I max=0.33.5A FBMH32 HL-type I max=0.32.5A I max=1.82.7A I max=13A FBMH45 FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS I max=4A HS-type I max=1.54A This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipbeads01_e-01 12 145 PART NUMBERS Standard Type FBMJ1608 Ordering code FB MJ1608HS280NT FB MJ1608HM230NT FB MJ1608HS280NTR FB MJ1608HM230NTR EHS Environmental Hazardous Substances RoHS RoHS RoHS RoHS Measuring frequency MHz DC Resistance max. Rated current Amax. Thickness mm inch 100 0.007 4.0 0.80.2 0.0310.008 100 0.006 6.0 0.80.2 0.0310.008 Measuring frequency MHz DC Resistance max. Rated current Amax. Thickness mm inch 4225% 2530% 3325% 2130% 830% 100 0.008 0.004 0.008 0.004 0.008 4.0 6.0 4.0 6.0 4.0 0.850.2 0.0330.008 Impedance Measuring frequency MHz DC Resistance max. Rated current Amax. Thickness mm inch 8025% 4830% 6025% 3830% 1630% 100 0.010 0.005 0.010 0.005 0.012 4.0 6.0 4.0 6.0 4.0 1.10.2 0.0430.008 Impedance Measuring frequency MHz DC Resistance max. Rated current Amax. Thickness mm inch 11025% 7230% 9025% 5630% 2330% 100 0.014 0.007 0.014 0.007 0.014 4.0 6.0 4.0 6.0 3.5 1.10.2 0.0430.008 Impedance Measuring frequency MHz DC Resistance max. Rated current Amax. Thickness mm inch 100 0.020 0.025 0.035 0.050 0.070 0.130 0.150 0.170 0.350 0.028 0.045 0.130 0.170 0.210 0.350 0.450 0.025 0.032 0.060 0.080 0.050 0.070 0.100 0.042 0.100 0.130 0.060 0.130 0.028 0.060 0.130 3.5 3.0 2.0 2.0 1.5 0.9 0.7 0.7 0.5 2.5 1.8 0.9 0.7 0.6 0.5 0.4 2.7 2.5 2.0 1.8 2.0 2.0 1.5 3.0 2.0 1.2 3.0 2.0 4.0 3.0 1.3 Impedance 2830% 2330% 2830% 2330% FBMJ2125 Ordering code FB FB FB FB FB MJ2125HS420-T MJ2125HS250NT MJ2125HM330-T MJ2125HM210NT MJ2125HL8R0NT EHS Environmental Hazardous Substances RoHS RoHS RoHS RoHS RoHS Impedance FBMJ3216 Ordering code FB FB FB FB FB MJ3216HS800-T MJ3216HS480NT MJ3216HM600-T MJ3216HM380NT MJ3216HL160NT EHS Environmental Hazardous Substances RoHS RoHS RoHS RoHS RoHS FBMJ4516 Ordering code FB FB FB FB FB MJ4516HS111-T MJ4516HS720NT MJ4516HM900-T MJ4516HM560NT MJ4516HL230NT EHS Environmental Hazardous Substances RoHS RoHS RoHS RoHS RoHS High impedance Type Ordering code FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB MH1608HM470-T MH1608HM600-T MH1608HM101-T MH1608HM151-T MH1608HM221-T MH1608HM331-T MH1608HM471-T MH1608HM601-T MH1608HM102-T MH1608HL300-T MH1608HL600-T MH1608HL121-T MH1608HL221-T MH1608HL331-T MH1608HL471-T MH1608HL601-T MH2012HM800-T MH2012HM121-T MH2012HM221-T MH2012HM331-T MH2016HM251NT MH3216HM501NT MH4516HM851NT MH3225HM601NT MH3225HM102NT MH3225HM202NT MH4525HM102NT MH4525HM162NT MH4532HM681-T MH4532HM132-T MH4532HM202-T EHS Environmental Hazardous Substances RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 4725% 6025% 10025% 15025% 22025% 33025% 47025% 60025% 100025% 3025% 6025% 12025% 22025% 33025% 47025% 60025% 8025% 12025% 22025% 33025% 25030% 50030% 85030% 60030% 100030% 200030% 100030% 160030% 68025% 130025% 200025% 0.80.1 0.0310.004 0.850.2 0.0330.008 1.60.2 0.0630.008 2.50.3 0.0980.012 3.20.3 0.1260.012 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 146 12 chipbeads01_e-01 ELECTRICAL CHARACTERISTICS Standard Type FBMJ1608 FBMJ2125 FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS FBMJ3216 FBMJ3216HL160NT 70 60 50 40 30 20 10 0 FBMJ4516 FBMJ4516HL230NT 100 90 80 70 60 50 40 30 20 10 0 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipbeads01_e-01 12 147 ELECTRICAL CHARACTERISTICS High impedance Type FBMH1608HM470-T 200 FBMH1608HM600-T 200 180 180 160 160 160 140 140 140 120 120 120 100 100 100 80 80 Z 60 X 20 0 1 600 10 100 10000 FBMH1608HM221-T 0 1 500 400 400 R 1600 1000 10000 FBMH1608HM102-T 1200 Z 1000 800 1000 100 1000 10000 FBMH1608HL221-T 1200 1000 1000 100 1000 10000 0 1 200 Z R R X 10 100 1000 X 0 1 10 100 1000 10000 X 10 100 1000 10000 FBMH1608HL121-T Z 400 150 300 100 200 100 1000 10000 FBMH2012HM800-T 0 0 1 10 100 1000 10000 FBMH1608HL471-T Z R X 400 X 1 10 100 1000 10000 FBMH2012HM121-T 0 1 400 300 250 250 200 200 200 Z 150 800 100 1000 10000 FBMH2012HM221-T 1 800 10 100 1000 10000 FBMH2012HM331-T 600 Z Z R 400 R 1000 X 200 X 10000 FBMH3216HM501NT 0 1 1200 10 100 1000 10000 FBMH4516HM851NT 0 1 1200 1000 600 X 50 X 10 100 100 50 0 1 10 0 150 R 100 FBMH2016HM251NT 500 200 300 10000 R 1000 600 250 1000 10000 Z 1500 300 X 1000 R 1000 350 R 100 2000 350 50 10 FBMH1608HL601 2500 800 400 Z 0 1 Z 1200 350 150 X 100 1400 200 100 R 1800 400 X 200 10 100 1000 10000 FBMH3225HM601NT 1000 600 R 800 400 Z 400 R Z 100 1000 10 100 1000 0 1 10 100 R Z 400 X 200 X 10 600 400 200 0 1 800 Z 600 X R 200 0 1 0 1 600 R 2000 600 300 100 R 500 FBMH1608HL331-T 800 400 10 Z X 1000 Z 100 10000 FBMH1608HM601-T 200 10000 1600 10 1000 400 50 1200 500 100 600 FBMH1608HL600-T 300 10 800 Z 400 FBMH1608HL300-T 1400 R 600 800 1600 1400 250 100 700 0 1 FBMH1608HM471-T X 0 1 1200 200 X 800 400 10000 1400 250 150 900 0 1 1000 200 10 50 10 100 800 X 0 1 R 200 0 1 10 Z 600 400 0 1 600 300 1400 R 100 X 1600 100 X 100 10000 R 200 100 10 1000 Z 300 Z 200 0 1 100 Z 200 20 FBMH1608HM331-T 600 500 300 10 300 R 40 X 20 1000 400 Z 60 R 40 FBMH1608HM151-T 600 500 80 Z 60 R 40 FBMH1608HM101-T 200 180 200 1000 0 1 X 10 100 1000 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 148 12 chipbeads01_e-01 ELECTRICAL CHARACTERISTICS High impedance Type 1200 FBMH3225HM102NT FBMH3225HM202NT FBMH4525HM102NT 2500 1000 2000 800 1500 R R Z 1000 1400 1000 1000 1200 Z 10 100 X 1000 0 1 FBMH4532HM681-T 1600 1400 1400 1000 1000 1200 1200 800 800 400 100 0 1 10 0 1000 0 1 10 1500 Z R Z R 1000 500 X X 1 100 1000 FBM4532HM202-T 200 1000 100 2000 400 X 10 1000 X 200 2500 600 R 200 400 X 200 10 100 1000 0 1 10 100 1000 FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS 1600 Z 100 R 600 FBM4532HM132-T 1800 600 10 Z 800 R 400 500 X 1800 1 1400 600 200 0 1600 800 400 0 1 1800 1600 1200 Z 600 FBMH4525HM162NT 1800 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipbeads01_e-01 12 149 PACKAGING Minimum Quantity Type 1608 0603 2125 0805 2012 0805 2016 0806 3216 1206 4516 1806 3225 1210 4525 1810 4532 1812 Tape Material Taping Dimensions Standard Quantitypcs Paper Tape Embossed Tape 4000 4000 4000 2000 2000 2000 1000 1000 2000 Paper tape (0.315 inches wide) Chip Cavity Type A Insertion Pitch Tape Thickness F T B FBMJ1608 1.00.2 1.80.2 4.00.2 1.1max FBMH1608 0603 0.0390.0080.0710.0080.1570.008 0.043max FBMJ2125 1.50.2 2.30.2 4.00.2 1.1max FBMH2012 0805 0.0590.0080.0910.0080.1570.008 0.043max Unit : mminch Embossed tape (0.315 inches wide) Insertion Pitch Chip Cavity Type A B F Tape Thickness K T 1.80.2 2.20.2 4.00.2 2.6max 0.6max FBMH2016 0806 0.0710.0080.0870.0080.1570.0080.102max0.024max 1.90.2 3.50.2 4.00.2 1.5max 0.3max FBMJ3216 1206 0.0750.0080.1380.0080.1570.0080.059max0.012max 1.90.2 3.50.2 4.00.2 2.6max 0.6max FBMH3216 1206 0.0750.0080.1380.0080.1570.0080.102max0.024max 2.80.2 3.50.2 4.00.2 4.0max 0.6max FBMH3225 1210 0.1100.0080.1380.0080.1570.0080.157max0.024max Unit : mminch Embossed tape (0.472 inches wide) Insertion Pitch Chip Cavity Type A B F Tape Thickness K T 1.90.2 4.90.2 4.00.2 1.5max 0.3max FBMJ4516 1806 0.0750.0080.1930.0080.1570.0080.059max0.012max 1.90.2 4.90.2 4.00.2 2.6max 0.6max FBMH4516 1806 0.0750.0080.1930.0080.1570.0080.102max0.024max 2.90.2 4.90.2 4.00.2 4.0max 0.6max FBMH4525 1810 0.1140.0080.1930.0080.1570.0080.157max0.024max 3.60.2 4.90.2 8.00.2 4.0max 0.6max FBMH4532 1812 0.1420.0080.1930.0080.3150.0080.157max0.024max Unit : mminch This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipbeads_reli-PRP1 12 chipbeads_reli_e-01 PACKAGING Leader and Blank portion A [mm]inch Type B [mm]inch FBMJ1608 10.01.5 0.3940.047 FBMJ2125 FBMJ3216 14.01.5 0.5510.059 FBMJ4516 FBMH1608 1800 3 FBMH2012 7.090 0.118 FBMH2016 Reel size W [mm]inch 601 0 2.360.039 0 FBMH3216 10.01.5 0.3940.047 FBMH3225 FBMH4516 14.01.5 0.5510.059 FBMH4525 FBMH4532 3302.0 12.990.080 1001.0 3.940.039 142.0 0.5510.080 Top tape strength The top tape requires a peel-off force of 0.1 to 0.7N in the direction of the arrow as illustrated below. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipbeads_reli_e-01 12 chipbeads_reli-PRP2 RELIABILITY DATA CHIP BEAD INDUCTORS FOR POWER LINE (FB SERIES M TYPE) 1. Operating Temperature Range 40125 Including self-generated heat Specified Value 2. Storage Temperature Range Specified Value Test Methods and Remarks *Note: 0 to 40 in taped packaging 4085 3. Impedance Within the specified tolerance Specified Value Test Methods and Remarks Measuring equipment : Impedance analyzer (HP4291A) or its equivalent Measuring frequency : 1001 MHz 4. DC Resistance Within the specified range Specified Value Test Methods and Remarks Four-terminal method Measuring equipment : Milliohm High-Tester 3226 (Hioki Denki) or its equivalent 5. Rated Current Specified Value Within the specified range 6. Vibration : No significant abnormality Appearance Impedance change : Within 30% of the initial value Specified Value Test Methods and Remarks According to JIS C 0040. Vibration type : A Time : 2 hrs each in X,Y, and Z directions Total: 6 hrs Frequency range : 10 to 55 to 10Hz (/min.) Amplitude : 1.5 mm (shall not exceed acceleration 196m/s2) Mounting method : Soldering onto PC board 7. Solderability Specified Value Test Methods and Remarks Solder temperature : 2305 Immersion time : 41 sec. Preconditioning : Immersion into flux. Immersion and Removal speed : 25mm/sec. 90% or more of immersed surface of terminal electrode shall be covered with fresh solder. 8. Resistance to Soldering Heat : No significant abnormality Appearance Impedance change : Within 30% of the initial value Specified Value Test Methods and Remarks Preheating Resistance to Soldering Heat Duration Preconditioning Immersion and Removal speed Recovery : : : : : : 150 for 3 min. 2605 100.5 sec. Immersion into flux. 25mm/sec. 2 to 3 hrs of recovery under the standard condition after the test. 9. Thermal Shock Appearance : No significant abnormality Impedance change : Within50 10 % of the initial value Specified Value Test Methods and Remarks According to JIS C 0025. Conditions for 1 cycle Step Temperature () 1 403 2 Room Temperature 3 852 4 Room Temperature Duration (min.) 303 Within 3 303 Within 3 Number of cycles : 100 Mounting method : Soldering onto PC board Recovery : 2 to 3 hrs of recovery under the standard condition after the removal from test chamber. 10. Resistance to Humidity (steady state) Specified Value : No significant abnormality Appearances Impedance change : Within 30% of the initial value Test Methods and Remarks : 402 Temperature Humidity : 90 to 95% RH Duration : 50024 0 hrs Mounting method : Soldering onto PC board : 2 to 3 hrs of recovery under the standard condition after the removal from test chamber. Recovery This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipbeads_reli-PRP3 12 chipbeads_reli_e-01 RELIABILITY DATA CHIP BEAD INDUCTORS FOR POWER LINE (FB SERIES M TYPE) 11. Loading under Damp Heat Specified Value Appearances : No significant abnormality Impedance change : Within 30% of the initial value Test Methods and Remarks Temperature402 Humidity90 to 95%RH Applied currentRated current Duration50024 0 hrs Mounting methodSoldering onto PC board Recovery2 to 3hrs of recovery under the standard condition after the removal from test chamber. 12. High Temperature Loading Test : No significant abnormality Appearance Specified Value Impedance change : Within 30% of the initial value Test Methods and Remarks Temperature852 Duration50024 0 hrs Applied currentRated current Mounting methodSoldering onto PC board Recovery2 to 3 hrs of recovery under the standard condition after the removal from test chamber. 13. Bending Strength Specified Value Test Methods and Remarks : 2mm Warp Testing board : Glass epoxy-resin substrate Thickness : 0.8mm 14. Adhesion of Electrode Specified Value Test Methods and Remarks Applied force : 5N Duration : 10 sec. Appearance : No mechanical damage. No separation or indication of separation of electrode. Note on standard condition: "standard condition" referred to herein is defined as follows: 5 to 35 of temperature, 45 to 85% relative humidity and 86 to 106kPa of air pressure. When there are questions concerning measurement results: In order to provide correlation data, the test shall be conducted under condition of 202 of temperature, 60 to 70% relative humidity and 86 to 106kPa of air pressure. Unless otherwise specified, all the tests are conducted under the "standard condition." This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipbeads_reli_e-01 12 chipbeads_reli-PRP4 PRECAUTIONS FBM Type 1. Circuit Design Operating environment 1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where Precautions product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. Rated current 1. Rated current of this product is shown in this catalogue, but please be sure to have the base board designed with adequate inspection in case of the generation of heat becomes high within the rated current range when the base board is in high resistance or in bad heating conditions. 2. PCB Design Land pattern design 1. Please refer to a recommended land pattern. Precautions 3. Considerations for automatic placement Adjustment of mounting machine 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. Precautions 2. Mounting and soldering conditions should be checked beforehand. Technical Adjustment of mounting machine consider1. When installing products, care should be taken not to apply distortion stress as it may deform the products. ations 4. Soldering Technical considerations Recommended reflow conditionPb free solder Peak 260 max 10sec max 230 min 200 180 150 150 3010sec 250 100 50 0 9030sec. Duration sec Recommended reflow conditionPb solder Solder joint temperature Solder joint temperature Wave soldering 1. Please refer to the specifications in the catalog for a wave soldering. Reflow soldering 1. Please contact any of our offices for a reflow soldering, and refer to the recommended condition specified. Lead free soldering 1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, etc. sufficiently. Preheating when soldering Precautions Heating : The temperature difference between soldering and remaining heat should not be greater than 150. Cooling : The temperature difference between the components and cleaning process should not be greater than 100. Recommended conditions for using a soldering iron Put the soldering iron on the land-pattern. Soldering iron's temperature - Below 350 Duration - 3 seconds or less The soldering iron should not directly touch the inductor. Wave, Reflow, Lead free soldering 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. 5sec max. 250 200 150 2405 180 150 100 50 0 2205 3010sec 9030sec. Duration sec Preheating when soldering 1. There is a case that products get damaged by a heat shock. Recommended conditions for using a soldering iron 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. 5. Handling Handling 1. Keep the inductors away from all magnets and magnetic objects. Setting PC boards 1. When setting a chip mounted base board, please make sure that there is no residual stress to the chip by distortion in the board or at screw part. Precautions Breakaway PC boards (splitting along perforations) 1. When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the board. 2. Board separation should not be done manually, but by using the appropriate devices. Mechanical considerations 1. Please do not give the inductors any excessive mechanical shocks. Handling 1. There is a case that a characteristic varies with magnetic influence. Setting PC boards Technical 1. There is a case that a characteristic varies with residual stress. considerBreakaway PC boards (splitting along perforations) ations 1. Planning pattern configurations and the position of products should be carefully performed to minimize stress. Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 6. Storage conditions Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. Recommended conditions Precautions Ambient temperature 040 Humidity Below 70% RH The ambient temperature must be kept below 30. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, inductors should be used within 6 months from the time of delivery. Technical Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of considerations taping/packaging materials may take place. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipbeads_reli-PRP5 12 chipbeads_reli_e-01