[ /Title (CD74 HC164 , CD74 HCT16 4) /Subject (High Speed CMOS Logic 8-Bit SerialIn/Parallel- CD54HC164, CD74HC164, CD54HCT164, CD74HCT164 Data sheet acquired from Harris Semiconductor SCHS155C High-Speed CMOS Logic 8-Bit Serial-In/Parallel-Out Shift Register October 1997 - Revised August 2003 Features Description * Buffered Inputs The 'HC164 and 'HCT164 are 8-bit serial-in parallel-out shift registers with asynchronous reset. Data is shifted on the positive edge of Clock (CP). A LOW on the Master Reset (MR) pin resets the shift register and all outputs go to the LOW state regardless of the input conditions. Two Serial Data inputs (DS1 and DS2) are provided, either one can be used as a Data Enable control. * Asynchronous Master Reset * Typical fMAX = 60MHz at VCC = 5V, CL = 15pF, TA = 25oC * Fanout (Over Temperature Range) - Standard Outputs . . . . . . . . . . . . . . . 10 LSTTL Loads - Bus Driver Outputs . . . . . . . . . . . . . 15 LSTTL Loads Ordering Information * Wide Operating Temperature Range . . . -55oC to 125oC * Balanced Propagation Delay and Transition Times PART NUMBER * Significant Power Reduction Compared to LSTTL Logic ICs TEMP. RANGE (oC) PACKAGE CD54HC164F3A -55 to 125 14 Ld CERDIP * HC Types - 2V to 6V Operation - High Noise Immunity: NIL = 30%, NIH = 30% of VCC at VCC = 5V CD54HCT164F3A -55 to 125 14 Ld CERDIP CD74HC164E -55 to 125 14 Ld PDIP CD74HC164M -55 to 125 14 Ld SOIC * HCT Types - 4.5V to 5.5V Operation - Direct LSTTL Input Logic Compatibility, VIL= 0.8V (Max), VIH = 2V (Min) - CMOS Input Compatibility, Il 1A at VOL, VOH CD74HC164MT -55 to 125 14 Ld SOIC CD74HC164M96 -55 to 125 14 Ld SOIC CD74HCT164E -55 to 125 14 Ld PDIP CD74HCT164M -55 to 125 14 Ld SOIC CD74HCT164MT -55 to 125 14 Ld SOIC CD74HCT164M96 -55 to 125 14 Ld SOIC NOTE: When ordering, use the entire part number. The suffix 96 denotes tape and reel. The suffix T denotes a small-quantity reel of 250. Pinout CD54HC164, CD54HCT164 (CERDIP) CD74HC164, CD74HCT164 (PDIP, SOIC) TOP VIEW DS1 1 14 VCC DS2 2 13 Q7 Q0 3 12 Q6 Q1 4 11 Q5 Q2 5 10 Q4 Q3 6 9 MR GND 7 8 CP CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright (c) 2003, Texas Instruments Incorporated 1 CD54HC164, CD74HC164, CD54HCT164, CD74HCT164 Functional Diagram 3 1 DS1 Q0 4 2 Q1 5 DS2 Q2 6 Q3 10 Q4 11 Q5 12 Q6 13 9 Q7 8 MR GND = 7 VCC = 14 CP TRUTH TABLE INPUTS OUTPUTS OPERATING MODE MR CP DS1 DS2 Q0 Q1 - Q7 RESET (CLEAR) L X X X L L-L Shift H l l L q0 - q6 H l h L q0 - q6 H h l L q0 - q6 H h h H q0 - q6 H= High Voltage Level. h= High Voltage Level One Set-up Time Prior To The Low-to-high Clock Transition. l= Low Voltage Level One Set-up Time Prior To The Low-to-high Clock Transition. L= Low Voltage Level. X= Don't Care. = Transition from Low to High Level. qn= Lower Case Letters Indicate The State Of the Reference Input Clock Transition. 2 CD54HC164, CD74HC164, CD54HCT164, CD74HCT164 Absolute Maximum Ratings Thermal Information DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V DC Input Diode Current, IIK For VI < -0.5V or VI > VCC + 0.5V . . . . . . . . . . . . . . . . . . . . . .20mA DC Output Diode Current, IOK For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .20mA DC Output Source or Sink Current per Output Pin, IO For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .25mA DC VCC or Ground Current, ICC or IGND . . . . . . . . . . . . . . . . . .50mA Thermal Resistance (Typical, Note 1) JA (oC/W) E (PDIP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . 80 M (SOIC) Package. . . . . . . . . . . . . . . . . . . . . . . . . . 86 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range (TA) . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Supply Voltage Range, VCC HC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 6V HCT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V DC Input or Output Voltage, VI, VO . . . . . . . . . . . . . . . . . 0V to VCC Input Rise and Fall Time 2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000ns (Max) 4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500ns (Max) 6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400ns (Max) CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. The package thermal impedance is calculated in accordance with JESD 51-7. DC Electrical Specifications TEST CONDITIONS PARAMETER SYMBOL VI (V) High Level Input Voltage VIH - Low Level Input Voltage VIL 25oC IO (mA) VCC (V) -40oC TO 85oC -55oC TO 125oC MIN TYP MAX MIN MAX MIN MAX UNITS 2 1.5 - - 1.5 - 1.5 - V 4.5 3.15 - - 3.15 - 3.15 - V 6 4.2 - - 4.2 - 4.2 - V 2 - - 0.5 - 0.5 - 0.5 V 4.5 - - 1.35 - 1.35 - 1.35 V 6 - - 1.8 - 1.8 - 1.8 V -0.02 2 1.9 - - 1.9 - 1.9 - V -0.02 4.5 4.4 - - 4.4 - 4.4 - V -0.02 6 5.9 - - 5.9 - 5.9 - V -4 4.5 3.98 - - 3.84 - 3.7 - V -5.2 6 5.48 - - 5.34 - 5.2 - V HC TYPES High Level Output Voltage CMOS Loads VOH - VIH or VIL High Level Output Voltage TTL Loads Low Level Output Voltage CMOS Loads VOL VIH or VIL Low Level Output Voltage TTL Loads Input Leakage Current Quiescent Device Current - - 0.02 2 - - 0.1 - 0.1 - 0.1 V 0.02 4.5 - - 0.1 - 0.1 - 0.1 V 0.02 6 - - 0.1 - 0.1 - 0.1 V 4 4.5 - - 0.26 - 0.33 - 0.4 V 5.2 6 - - 0.26 - 0.33 - 0.4 V II VCC or GND - 6 - - 0.1 - 1 - 1 A ICC VCC or GND 0 6 - - 8 - 80 - 160 A 3 CD54HC164, CD74HC164, CD54HCT164, CD74HCT164 DC Electrical Specifications (Continued) TEST CONDITIONS SYMBOL VI (V) High Level Input Voltage VIH - - Low Level Input Voltage VIL - High Level Output Voltage CMOS Loads VOH VIH or VIL PARAMETER 25oC IO (mA) VCC (V) -40oC TO 85oC -55oC TO 125oC MIN TYP MAX MIN MAX MIN MAX UNITS 4.5 to 5.5 2 - - 2 - 2 - V - 4.5 to 5.5 - - 0.8 - 0.8 - 0.8 V -0.02 4.5 4.4 - - 4.4 - 4.4 - V -4 4.5 3.98 - - 3.84 - 3.7 - V 0.02 4.5 - - 0.1 - 0.1 - 0.1 V 4 4.5 - - 0.26 - 0.33 - 0.4 V HCT TYPES High Level Output Voltage TTL Loads Low Level Output Voltage CMOS Loads VOL VIH or VIL Low Level Output Voltage TTL Loads II VCC to GND 0 5.5 - - 0.1 - 1 - 1 A ICC VCC or GND 0 5.5 - - 8 - 80 - 160 A ICC (Note 2) VCC -2.1 - 4.5 to 5.5 - 100 360 - 450 - 490 A Input Leakage Current Quiescent Device Current Additional Quiescent Device Current Per Input Pin: 1 Unit Load NOTE: 2. For dual-supply systems theoretical worst case (VI = 2.4V, VCC = 5.5V) specification is 1.8mA. HCT Input Loading Table INPUT UNIT LOADS Date Shift-In (1, 2) 0.3 MR 0.9 Clock 0.7 NOTE: Unit Load is ICC limit specified in DC Electrical Specifications table, e.g. 360A max at 25oC. Prerequisite For Switching Function 25oC PARAMETER -40oC TO 85oC -55oC TO 125oC SYMBOL VCC (V) MIN MAX MIN MAX MIN MAX UNITS fMAX 2 6 - 5 - 4 - MHz 4.5 30 - 24 - 20 - MHz 6 35 - 28 - 24 - MHz 2 60 - 75 - 90 - ns 4.5 12 - 15 - 18 - ns 6 10 - 13 - 15 - ns HC TYPES Maximum Clock Frequency MR Pulse Width tw 4 CD54HC164, CD74HC164, CD54HCT164, CD74HCT164 Prerequisite For Switching Function (Continued) 25oC -40oC TO 85oC -55oC TO 125oC SYMBOL VCC (V) MIN MAX MIN MAX MIN MAX UNITS tW 2 80 - 100 - 120 - ns 4.5 16 - 20 - 24 - ns 6 14 - 17 - 20 - ns 2 60 - 75 - 90 - ns 4.5 12 - 15 - 18 - ns 6 10 - 13 - 15 - ns 2 4 - 4 - 4 - ns 4.5 4 - 4 - 4 - ns 6 4 - 4 - 4 - ns 2 80 - 100 - 120 - ns 4.5 16 - 20 - 24 - ns 6 14 - 17 - 20 - ns fMAX 4.5 27 - 22 - 18 - MHz tw 6 18 - 23 - 27 - ns CP Pulse Width tw 4.5 18 - 23 - 27 - ns Set-up Time tSU 6 12 - 15 - 18 - ns Hold Time tH 4.5 4 - 4 - 4 - ns tREM 6 16 - 20 - 24 - ns PARAMETER CP Pulse Width Set-up Time tSU Hold Time tH MR to Clock, Removal Time tREM HCT TYPES Maximum Clock Frequency MR Pulse Width MR to Clock, Removal Time Switching Specifications PARAMETER Input tr, tf = 6ns SYMBOL TEST CONDITIONS tPLH, tPHL CL = 50pF 25oC -40oC TO 85oC -55oC TO 125oC VCC (V) TYP MAX MAX MAX UNITS 2 - 170 212 255 ns 4.5 - 34 43 51 ns CL = 15pF 5 14 - - - ns CL = 50pF 6 - 29 36 43 ns CL = 50pF 2 - 140 175 210 ns 4.5 - 28 35 42 ns CL = 15pF 5 11 - - - ns CL = 50pF 6 - 24 30 36 ns CL = 50pF 2 - 75 - 110 ns 4.5 - 15 - 22 ns 6 - 13 - 19 ns HC TYPES Propagation Delay, CP to Qn MR to Qn Output Transition Times Maximum Clock Frequency Input Capacitance tPLH, tPHL tTLH, tTHL fMAX CL = 15pF 5 60 - - - MHz CIN - - - 10 10 10 pF 5 CD54HC164, CD74HC164, CD54HCT164, CD74HCT164 Switching Specifications PARAMETER Input tr, tf = 6ns (Continued) 25oC -40oC TO 85oC -55oC TO 125oC SYMBOL TEST CONDITIONS VCC (V) TYP MAX MAX MAX UNITS CPD - 5 47 - - - pF CL = 50pF 4.5 - 36 45 54 ns CL = 15pF 5 15 - - - ns CL = 50pF 4.5 - 38 46 57 ns CL = 15pF 5 16 - - - ns CL = 50pF 4.5 - 15 19 22 ns Power Dissipation Capacitance (Notes 3, 4) HCT TYPES Propagation Delay, CP to Qn tPLH, tPHL MR to Qn tPLH, tPHL Output Transition Times tTLH, tTHL Input Capacitance CIN - - - - - - pF Maximum Clock Frequency fMAX CL = 15pF - 54 - - - MHz Power Dissipation Capacitance (Notes 3, 4) CPD - 5 49 10 10 10 pF NOTES: 3. CPD is used to determine the dynamic power consumption, per device. 4. PD = VCC2 fi + (CL VCC2 + fO) where fi = Input Frequency, fO = Output Frequency, CL = Output Load Capacitance, VCC = Supply Voltage. Test Circuits and Waveforms CLOCK INPUT trCL tfCL trCL VCC 90% GND tH(H) GND tH(H) VCC DATA INPUT 50% tH(L) 3V 1.3V 1.3V 1.3V GND tSU(H) tSU(H) tSU(L) tTLH 90% OUTPUT tTHL 90% 50% 10% tTLH 90% 1.3V OUTPUT tREM 3V SET, RESET OR PRESET GND tTHL 1.3V 10% FIGURE 1. HC SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND PROPAGATION DELAY TIMES FOR EDGE TRIGGERED SEQUENTIAL LOGIC CIRCUITS tPHL 1.3V GND IC CL 50pF GND 90% tPLH 50% IC tSU(L) tPHL tPLH tREM VCC SET, RESET OR PRESET 1.3V 0.3V tH(L) DATA INPUT 3V 2.7V CLOCK INPUT 50% 10% tfCL CL 50pF FIGURE 2. HCT SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND PROPAGATION DELAY TIMES FOR EDGE TRIGGERED SEQUENTIAL LOGIC CIRCUITS 6 PACKAGE OPTION ADDENDUM www.ti.com 5-Sep-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp Samples (Requires Login) 5962-8970401CA ACTIVE CDIP J 14 1 TBD Call TI CD54HC164F ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type Call TI CD54HC164F3A ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type CD54HCT164F3A ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type CD74HC164E ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD74HC164EE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD74HC164M ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC164M96 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC164M96E4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC164M96G4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC164ME4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC164MG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC164MT ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC164MTE4 ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC164MTG4 ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT164E ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD74HCT164EE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD74HCT164M ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT164M96 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT164M96E4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 (3) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 5-Sep-2011 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp CD74HCT164M96G4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT164ME4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT164MG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT164MT ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT164MTE4 ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT164MTG4 ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (3) Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 5-Sep-2011 OTHER QUALIFIED VERSIONS OF CD54HC164, CD54HCT164, CD74HC164, CD74HCT164 : * Catalog: CD74HC164, CD74HCT164 * Military: CD54HC164, CD54HCT164 NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Military - QML certified for Military and Defense Applications Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 6-Aug-2010 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing CD74HC164M96 SOIC D 14 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 CD74HC164MT SOIC D 14 250 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 CD74HCT164M96 SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 CD74HCT164MT SOIC D 14 250 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 6-Aug-2010 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) CD74HC164M96 SOIC D 14 2500 346.0 346.0 33.0 CD74HC164MT SOIC D 14 250 346.0 346.0 33.0 CD74HCT164M96 SOIC D 14 2500 346.0 346.0 33.0 CD74HCT164MT SOIC D 14 250 346.0 346.0 33.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connctivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated