Notice for TAIYO YUDEN Products
[ For General Electronic Equipment
(General Environment) ]
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2017. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully
before practical application or use of our products.
Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or
equipment incorporating our products, which are caused under the conditions other than those specified in this
catalog or individual product specification sheets.
■ Please contact TAIYO YUDEN for further details of product specifications as the individual product specification
sheets are available.
■ Please conduct validation and verification of our products in actual condition of mounting and operating
environment before using our products.
■ The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA
equipment, home electric appliances, office equipment, information and communication equipment including,
without limitation, mobile phone, and PC) and medical equipment classified as Class I or II by IMDRF. Please be
sure to contact TAIYO YUDEN for further information before using the products for any equipment which may
directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation,
automotive powertrain control system, train control system, and ship control system, traffic signal equipment,
disaster prevention equipment, medical equipment classified as Class III by IMDRF, highly public information
network equipment including, without limitation, telephone exchange, and base station).
Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g.,
aerospace equipment, aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control
equipment, undersea equipment, military equipment).
*Note: There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g.,
in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN.
Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment.
When our products are used even for high safety and/or reliability-required devices or circuits of general electronic
equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to
install a protection circuit as necessary.
Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way
responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog
for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above.
■ Information contained in this catalog is intended to convey examples of typical performances and/or applications
of our products and is not intended to make any warranty with respect to the intellectual property rights or any
other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights.
■ Please note that the scope of warranty for our products is limited to the delivered our products themselves and
TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products.
Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality
assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in
accordance with such agreement.
■ The contents of this catalog are applicable to our products which are purchased from our sales offices or
authorized distributors (hereinafter TAIYO YUDENs official sales channel). Please note that the contents of this
catalog are not applicable to our products purchased from any seller other than TAIYO YUDENs official sales
channel.
■ Caution for Export
Some of our products listed in this catalog may require specific procedures for export according to U.S. Export
Administration Regulations, Foreign Exchange and Foreign Trade Control Law of Japan, and other applicable
regulations. Should you have any questions on this matter, please contact our sales staff.
1
8
c_mlcc_e-E06R01
MULTILAYER CERAMIC CAPACITORS
WAVE
REFLOW
■PARTS NUMBER
J M K 3 1 6 △ B J 1 0 6 M L － T △ △＝Blank space
① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫
①Rated voltage
Code Rated voltage［VDC］
P 2.5
A 4
J 6.3
L 10
E 16
T 25
G 35
U 50
H 100
Q 250
S 630
②Series name
Code Series name
M Multilayer ceramic capacitor
V Multilayer ceramic capacitor for high frequency
W LW reverse type multilayer capacitor
③End termination
Code End termination
K Plated
S Cu Internal Electrodes
④Dimension（L×W）
Type Dimensions
（L×W）［mm］ EIA（inch）
021 0.25× 0.125 008004
042 0.4 × 0.2 01005
063 0.6 × 0.3 0201
105 1.0 × 0.5 0402
0.52× 1.0 ※ 0204
107 1.6 × 0.8 0603
0.8 × 1.6 ※ 0306
212 2.0 × 1.25 0805
1.25× 2.0 ※ 0508
316 3.2 × 1.6 1206
325 3.2 × 2.5 1210
432 4.5 × 3.2 1812
Note : ※LW reverse type（□WK） only
⑤Dimension tolerance
Code Type L［mm］ W［mm］ T［mm］
△ ALL Standard Standard Standard
A
063 0.6±0.05 0.3±0.05 0.3±0.05
105 1.0±0.10 0.5±0.10 0.5±0.10
107 1.6＋0.15/－0.05 0.8＋0.15/－0.05 0.8＋0.15/－0.05
212 2.0＋0.15/－0.05 1.25＋0.15/－0.05
0.45±0.05
0.85±0.10
1.25＋0.15/－0.05
316 3.2±0.20 1.6±0.20 0.85±0.10
1.6±0.20
325 3.2±0.30 2.5±0.30 2.5±0.30
B
063 0.6±0.09 0.3±0.09 0.3±0.09
105 1.0＋0.15/－0.05 0.5＋0.15/－0.05 0.5＋0.15/－0.05
107 1.6＋0.20/－0 0.8＋0.20/－0 0.45±0.05
0.8＋0.20/－0
212 2.0＋0.20/－0 1.25＋0.20/－0
0.45±0.05
0.85±0.10
1.25＋0.20/－0
316 3.2±0.30 1.6±0.30 1.6±0.30
C 105 1.0＋0.20/－0 0.5＋0.20/－0 0.5＋0.20/－0
Note: cf. STANDARD EXTERNAL DIMENSIONS △= Blank space
⑥Temperature characteristics code
■High dielectric type（Excluding Super low distortion multilayer ceramic capacitor）
Code Applicable
standard
Temperature
range［℃］ Ref. Temp.［℃］ Capacitance change Capacitance
tolerance
Tolerance
code
BJ
JIS B －25～＋ 85 20 ±10％ ±10％ K
±20％ M
EIA X5R －55～＋ 85 25 ±15％ ±10％ K
±20％ M
B7 EIA X7R －55～＋125 25 ±15％ ±10％ K
±20％ M
C6 EIA X6S －55～＋105 25 ±22％ ±10％ K
±20％ M
C7 EIA X7S －55～＋125 25 ±22％ ±10％ K
±20％ M
LD(※) EIA X5R －55～＋ 85 25 ±15％ ±10％ K
±20％ M
Note : ※.LD Low distortion high value multilayer ceramic capacitor △= Blank space
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
REFLOWWAVE
MULTILAYER CERAMIC CAPACITORS
12
1
8
c_mlcc_e-E06R01
■Temperature compensating type
Code Applicable
standard
Temperature
range［℃］ Ref. Temp.［℃］ Capacitance change Capacitance
tolerance
Tolerance
code
CG EIA C0G －55～＋125 25 0±30ppm/℃
±0.05pF A
±0.1pF B
±0.25pF C
±0.5pF D
±5％ J
UJ JIS UJ －55～＋125 20 －750±120ppm/℃
±0.25pF C
±0.5pF D
EIA U2J 25 ±5％ J
UK JIS UK －55～＋125 20 －750±250ppm/℃ ±0.25pF C
EIA U2K －55～＋125 25
SL JIS SL －55～＋125 20 ＋350～－1000ppm/℃ ±5％ J
⑥Series code
・Super low distortion multilayer ceramic capacitor
Code Series code
SD Standard
・Medium-High Voltage Multilayer Ceramic Capacitor
Code Series code
SD Standard
⑦Nominal capacitance
Code
（example） Nominal capacitance
0R5 0.5pF
010 1pF
100 10pF
101 100pF
102 1,000pF
103 10,000pF
104 0.1μF
105 1.0μF
106 10μF
107 100μF
Note : R＝Decimal point
⑧Capacitance tolerance
Code Capacitance tolerance
A ±0.05pF
B ±0.1pF
C ±0.25pF
D ±0.5pF
F ±1pF
G ±2％
J ±5％
K ±10％
M ±20％
Z ＋80/－20％
⑨Thickness
Code Thickness［mm］
K 0.125
H 0.13
E 0.18
C 0.2
D
P 0.3
T
K 0.45（107type or more）
V 0.5
W
A 0.8
D 0.85（212type or more）
F 1.15
G 1.25
L 1.6
N 1.9
Y 2.0 max
M 2.5
⑩Special code
Code Special code
－ Standard
⑪Packaging
Code Packaging
F φ178mm Taping （2mm pitch）
T φ178mm Taping （4mm pitch）
P φ178mm Taping （4mm pitch, 1000 pcs/reel）
325 type（Thickness code M）
R φ178mm Taping （2mm pitch）105type only
（Thickness code E,H）
W φ178mm Taping（1mm pitch）021/042type only
⑫Internal code
Code Internal code
△ Standard
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
13
1
8
c_mlcc_e-E06R01
■STANDARD EXTERNAL DIMENSIONS
W
L
e
T
T
L
W
e
※ LW reverse type
Type( EIA ) Dimension [mm]
L W T *1 e
□MK021（008004） 0.25±0.013 0.125±0.013 0.125±0.013 K 0.0675±0.0275
□VS021（008004） 0.25±0.013 0.125±0.013 0.125±0.013 K 0.0675±0.0275
□MK042（01005） 0.4±0.02 0.2±0.02 0.2±0.02 C 0.1±0.03
D
□VS042（01005） 0.4±0.02 0.2±0.02 0.2±0.02 C 0.1±0.03
□MK063（0201） 0.6±0.03 0.3±0.03 0.3±0.03 P 0.15±0.05
T
□MK105（0402） 1.0±0.05 0.5±0.05
0.13±0.02 H
0.25±0.10
0.18±0.02 E
0.2±0.02 C
0.3±0.03 P
0.5±0.05 V
□VK105（0402） 1.0±0.05 0.5±0.05 0.5±0.05 W 0.25±0.10
□WK105（0204）※ 0.52±0.05 1.0±0.05 0.3±0.05 P 0.18±0.08
□MK107（0603） 1.6±0.10 0.8±0.10 0.45±0.05 K 0.35±0.25
0.8±0.10 A
□WK107（0306）※ 0.8±0.10 1.6±0.10 0.5±0.05 V 0.25±0.15
□MK212（0805） 2.0±0.10 1.25±0.10
0.45±0.05 K
0.5±0.25 0.85±0.10 D
1.25±0.10 G
□WK212（0508）※ 1.25±0.15 2.0±0.15 0.85±0.10 D 0.3±0.2
□MK316（1206） 3.2±0.15 1.6±0.15
0.85±0.10 D
0.5＋0.35/－0.25 1.15±0.10 F
1.6±0.20 L
□MK325（1210） 3.2±0.30 2.5±0.20
0.85±0.10 D
0.6±0.3
1.15±0.10 F
1.9±0.20 N
1.9＋0.1/－0.2 Y
2.5±0.20 M
□MK432（1812） 4.5±0.40 3.2±0.30 2.5±0.20 M 0.9±0.6
Note : ※. LW reverse type, *1.Thickness code
■STANDARD QUANTITY
Type EIA（inch） Dimension Standard quantity［pcs］
［mm］ Code Paper tape Embossed tape
021 008004 0.125 K － 50000
042 01005 0.2 C － 40000
D
063 0201 0.3 P 15000 －
T
105 0402
0.13 H － 20000
0.18 E － 15000
0.2 C 20000 －
0.3 P 15000 －
0.5 V
10000 －
W
0204 ※ 0.30 P
107 0603 0.45 K 4000 －
0.8 A
0306 ※ 0.50 V － 4000
212 0805
0.45 K 4000 －
0.85 D
1.25 G － 3000
0508 ※ 0.85 D 4000 －
316 1206
0.85 D 4000 －
1.15 F － 3000
1.6 L － 2000
325 1210
0.85 D
－ 2000
1.15 F
1.9 N
2.0 max Y
2.5 M － 1000
432 1812 2.5 M － 500
Note : ※.LW Reverse type（□WK）
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
14
1
8
■PARTS NUMBER
・ Capacitance tolerance code is applied to [] of part number.
Note)
*1 We may provide X7R/X7S for some items according to the individual specification.
*2 The exchange of individual specification is necessary depending on the application and circuit condition. Please contact TAIYO YUDEN sales channels.
*3 The size standard should look at ④Dimension, ⑤Dimension tolerance, and ⑨Thickness, and STANDARD EXTERNAL DIMENSIONS.
Multilayer Ceramic Capacitors (High dielectric type)
●021TYPE
【Temperature Characteristic BJ : X5R】　0.125mm thickness（K） 　
HTLT
Rated voltage x ％
EMK021 BJ221[]K-W X5R 220 p ±10, ±20 10 150 0.125±0.013 R
EMK021 BJ471[]K-W X5R 470 p ±10, ±20 10 150 0.125±0.013 R
EMK021 BJ102[]K-W X5R 1000 p ±10, ±20 10 150 0.125±0.013 R
JMK021 BJ222[]K-W X5R 2200 p ±10, ±20 10 150 0.125±0.013 R
JMK021 BJ472[]K-W X5R 4700 p ±10, ±20 10 150 0.125±0.013 R
JMK021 BJ103[]K-W X5R 0.01 μ ±10, ±20 10 150 0.125±0.013 R
AMK021 BJ223MK-W 4 X5R 0.022 μ ±20 10 150 0.125±0.013 R
●042TYPE
【Temperature Characteristic BJ : B/X5R】　0.2mm thickness（C）
HTLT
Rated voltage x ％
EMK042 BJ101[]C-W B X5R 100 p ±10, ±20 5 200 0.2±0.02 R
EMK042 BJ151[]C-W B X5R 150 p ±10, ±20 5 200 0.2±0.02 R
EMK042 BJ221[]C-W B X5R 220 p ±10, ±20 5 200 0.2±0.02 R
EMK042 BJ331[]C-W B X5R 330 p ±10, ±20 5 200 0.2±0.02 R
EMK042 BJ471[]C-W B X5R 470 p ±10, ±20 5 200 0.2±0.02 R
EMK042 BJ681[]C-W B X5R 680 p ±10, ±20 5 200 0.2±0.02 R
EMK042 BJ102[]C-W B X5R 1000 p ±10, ±20 5 200 0.2±0.02 R
EMK042 BJ152[]C-W X5R 1500 p ±10, ±20 10 150 0.2±0.02 R
EMK042 BJ222[]C-W X5R 2200 p ±10, ±20 10 150 0.2±0.02 R
EMK042 BJ332[]C-W X5R 3300 p ±10, ±20 10 150 0.2±0.02 R
EMK042 BJ472[]C-W X5R 4700 p ±10, ±20 10 150 0.2±0.02 R
EMK042 BJ682[]C-W X5R 6800 p ±10, ±20 10 150 0.2±0.02 R
EMK042 BJ103[]C-W X5R 0.01 μ ±10, ±20 10 150 0.2±0.02 R
LMK042 BJ101[]C-W B X5R*1 100 p ±10, ±20 5 200 0.2±0.02 R
LMK042 BJ151[]C-W B X5R*1 150 p ±10, ±20 5 200 0.2±0.02 R
LMK042 BJ221[]C-W B X5R*1 220 p ±10, ±20 5 200 0.2±0.02 R
LMK042 BJ331[]C-W B X5R*1 330 p ±10, ±20 5 200 0.2±0.02 R
LMK042 BJ471[]C-W B X5R*1 470 p ±10, ±20 5 200 0.2±0.02 R
LMK042 BJ681[]C-W B X5R*1 680 p ±10, ±20 5 200 0.2±0.02 R
LMK042 BJ102[]C-W B X5R*1 1000 p ±10, ±20 5 200 0.2±0.02 R
LMK042 BJ152[]C-W X5R 1500 p ±10, ±20 10 150 0.2±0.02 R
LMK042 BJ222[]C-W X5R 2200 p ±10, ±20 10 150 0.2±0.02 R
LMK042 BJ332[]C-W X5R 3300 p ±10, ±20 10 150 0.2±0.02 R
LMK042 BJ472[]C-W X5R 4700 p ±10, ±20 10 150 0.2±0.02 R
LMK042 BJ682[]C-W X5R 6800 p ±10, ±20 10 150 0.2±0.02 R
LMK042 BJ103[]C-W X5R 0.01 μ ±10, ±20 10 150 0.2±0.02 R
JMK042 BJ152[]C-W B X5R*1 1500 p ±10, ±20 10 150 0.2±0.02 R
JMK042 BJ222[]C-W B X5R*1 2200 p ±10, ±20 10 150 0.2±0.02 R
JMK042 BJ332[]C-W B X5R*1 3300 p ±10, ±20 10 150 0.2±0.02 R
JMK042 BJ472[]C-W B X5R*1 4700 p ±10, ±20 10 150 0.2±0.02 R
JMK042 BJ682[]C-W B X5R*1 6800 p ±10, ±20 10 150 0.2±0.02 R
JMK042 BJ103[]C-W B X5R*1 0.01 μ ±10, ±20 10 150 0.2±0.02 R
JMK042 BJ223[]C-W X5R 0.022 μ ±10, ±20 10 150 0.2±0.02 R
JMK042 BJ473[]C-W X5R 0.047 μ ±10, ±20 10 150 0.2±0.02 R
JMK042 BJ104[]C-W X5R 0.1 μ ±10, ±20 10 150 0.2±0.02 R
AMK042 BJ473[]C-W X5R 0.047 μ ±10, ±20 10 150 0.2±0.02 R
AMK042 BJ104[]C-W X5R 0.1 μ ±10, ±20 10 150 0.2±0.02 R
【Temperature Characteristic B7 : X7R】　0.2mm thickness（C）
HTLT
Rated voltage x ％
EMK042 B7101[]C-W X7R 100 p ±10, ±20 5 200 0.2±0.02 R
EMK042 B7151[]C-W X7R 150 p ±10, ±20 5 200 0.2±0.02 R
EMK042 B7221[]C-W X7R 220 p ±10, ±20 5 200 0.2±0.02 R
EMK042 B7331[]C-W X7R 330 p ±10, ±20 5 200 0.2±0.02 R
EMK042 B7471[]C-W X7R 470 p ±10, ±20 5 200 0.2±0.02 R
EMK042 B7681[]C-W X7R 680 p ±10, ±20 5 200 0.2±0.02 R
EMK042 B7102[]C-W X7R 1000 p ±10, ±20 5 200 0.2±0.02 R
LMK042 B7101[]C-W X7R 100 p ±10, ±20 5 200 0.2±0.02 R
LMK042 B7151[]C-W X7R 150 p ±10, ±20 5 200 0.2±0.02 R
LMK042 B7221[]C-W X7R 220 p ±10, ±20 5 200 0.2±0.02 R
LMK042 B7331[]C-W X7R 330 p ±10, ±20 5 200 0.2±0.02 R
LMK042 B7471[]C-W X7R 470 p ±10, ±20 5 200 0.2±0.02 R
LMK042 B7681[]C-W X7R 680 p ±10, ±20 5 200 0.2±0.02 R
LMK042 B7102[]C-W X7R 1000 p ±10, ±20 5 200 0.2±0.02 R
・ All the Multilayer Ceramic Capacitors of the catalog lineup are RoHS Compliant.
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
Capacitance tolerance
[％]
4
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
16
6.3
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
16
10
6.3
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
16
10
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
15
1
8
■PARTS NUMBER
●063TYPE
【Temperature Characteristic BJ : B/X5R】　0.3mm thickness（P）
HTLT
Rated voltage x ％
UMK063 BJ101[]P-F B X5R*1 100 p ±10, ±20 3.5 200 0.3±0.03 R
UMK063 BJ151[]P-F B X5R*1 150 p ±10, ±20 3.5 200 0.3±0.03 R
UMK063 BJ221[]P-F B X5R*1 220 p ±10, ±20 3.5 200 0.3±0.03 R
UMK063 BJ331[]P-F B X5R*1 330 p ±10, ±20 3.5 200 0.3±0.03 R
UMK063 BJ471[]P-F B X5R*1 470 p ±10, ±20 3.5 200 0.3±0.03 R
UMK063 BJ681[]P-F B X5R*1 680 p ±10, ±20 3.5 200 0.3±0.03 R
UMK063 BJ102[]P-F B X5R*1 1000 p ±10, ±20 3.5 200 0.3±0.03 R
UMK063 BJ152[]P-F B X5R 1500 p ±10, ±20 5 200 0.3±0.03 R
UMK063 BJ222[]P-F B X5R 2200 p ±10, ±20 5 200 0.3±0.03 R
UMK063 BJ332[]P-F B X5R 3300 p ±10, ±20 5 200 0.3±0.03 R
UMK063 BJ472[]P-F B X5R 4700 p ±10, ±20 5 200 0.3±0.03 R
UMK063 BJ682[]P-F B X5R 6800 p ±10, ±20 5 200 0.3±0.03 R
UMK063 BJ103[]P-F B X5R 0.01 μ ±10, ±20 5 200 0.3±0.03 R
GMK063 BJ104[]P-F 35 X5R 0.1 μ ±10, ±20 10 150 0.3±0.03 R
TMK063 BJ152[]P-F B X5R 1500 p ±10, ±20 5 200 0.3±0.03 R
TMK063 BJ222[]P-F B X5R 2200 p ±10, ±20 5 200 0.3±0.03 R
TMK063 BJ332[]P-F B X5R 3300 p ±10, ±20 5 200 0.3±0.03 R
TMK063 BJ472[]P-F B X5R 4700 p ±10, ±20 5 200 0.3±0.03 R
TMK063 BJ682[]P-F B X5R 6800 p ±10, ±20 5 200 0.3±0.03 R
TMK063 BJ103[]P-F B X5R 0.01 μ ±10, ±20 5 200 0.3±0.03 R
TMK063 BJ223[]P-F B X5R 0.022 μ ±10, ±20 7.5 200 0.3±0.03 R
TMK063ABJ104[]P-F X5R 0.1 μ ±10, ±20 10 150 0.3±0.05 R
EMK063 BJ152[]P-F B X5R*1 1500 p ±10, ±20 5 200 0.3±0.03 R
EMK063 BJ222[]P-F B X5R*1 2200 p ±10, ±20 5 200 0.3±0.03 R
EMK063 BJ332[]P-F B X5R*1 3300 p ±10, ±20 5 200 0.3±0.03 R
EMK063 BJ472[]P-F B X5R*1 4700 p ±10, ±20 5 200 0.3±0.03 R
EMK063 BJ682[]P-F B X5R*1 6800 p ±10, ±20 5 200 0.3±0.03 R
EMK063 BJ103[]P-F B X5R*1 0.01 μ ±10, ±20 5 200 0.3±0.03 R
EMK063 BJ223[]P-F B X5R 0.022 μ ±10, ±20 7.5 200 0.3±0.03 R
EMK063 BJ333[]P-F X5R 0.033 μ ±10, ±20 7.5 150 0.3±0.03 R
EMK063 BJ473[]P-F X5R 0.047 μ ±10, ±20 7.5 150 0.3±0.03 R
EMK063 BJ683[]P-F X5R 0.068 μ ±10, ±20 10 150 0.3±0.03 R
EMK063 BJ104[]P-F X5R 0.1 μ ±10, ±20 10 150 0.3±0.03 R
EMK063 BJ224[]P-F X5R 0.22 μ ±10, ±20 10 150 0.3±0.03 R
EMK063BBJ474[]PLF X5R 0.47 μ ±10, ±20 10 150 0.3±0.09 R
LMK063 BJ223[]P-F B X5R 0.022 μ ±10, ±20 7.5 150 0.3±0.03 R
LMK063 BJ333[]P-F X5R 0.033 μ ±10, ±20 7.5 150 0.3±0.03 R
LMK063 BJ473[]P-F X5R 0.047 μ ±10, ±20 7.5 150 0.3±0.03 R
LMK063 BJ683[]P-F X5R 0.068 μ ±10, ±20 10 150 0.3±0.03 R
LMK063 BJ104[]P-F X5R 0.1 μ ±10, ±20 10 150 0.3±0.03 R
LMK063 BJ224[]P-F X5R 0.22 μ ±10, ±20 10 150 0.3±0.03 R
LMK063BBJ474[]PLF X5R 0.47 μ ±10, ±20 10 150 0.3±0.09 R
LMK063BBJ105MPLF X5R 1 μ ±20 10 150 0.3±0.09 R
JMK063 BJ223[]P-F B X5R 0.022 μ ±10, ±20 7.5 200 0.3±0.03 R
JMK063 BJ333[]P-F X5R 0.033 μ ±10, ±20 7.5 150 0.3±0.03 R
JMK063 BJ473[]P-F X5R 0.047 μ ±10, ±20 7.5 150 0.3±0.03 R
JMK063 BJ683[]P-F X5R 0.068 μ ±10, ±20 10 150 0.3±0.03 R
JMK063 BJ104[]P-F X5R 0.1 μ ±10, ±20 10 150 0.3±0.03 R
JMK063 BJ224[]P-F X5R 0.22 μ ±10, ±20 10 150 0.3±0.03 R
JMK063 BJ334MP-F X5R 0.33 μ ±20 10 150 0.3±0.03 R
JMK063 BJ474[]P-F X5R 0.47 μ ±10, ±20 10 150 0.3±0.03 R
JMK063ABJ105[]P-F X5R 1 μ ±10, ±20 10 150 0.3±0.05 R
AMK063 BJ224[]P-F X5R 0.22 μ ±10, ±20 10 150 0.3±0.03 R
AMK063 BJ334MP-F X5R 0.33 μ ±20 10 150 0.3±0.03 R
AMK063 BJ474[]P-F X5R 0.47 μ ±10, ±20 10 150 0.3±0.03 R
AMK063ABJ105[]P-F X5R 1 μ ±10, ±20 10 150 0.3±0.05 R
【Temperature Characteristic C6 : X6S】　0.3mm thickness（P）
HTLT
Rated voltage x ％
TMK063 C6104[]P-F 25 X6S 0.1 μ ±10, ±20 10 150 0.3±0.03 R
EMK063AC6104[]P-F 16 X6S 0.1 μ ±10, ±20 10 150 0.3±0.05 R
LMK063 C6333[]P-F X6S 0.033 μ ±10, ±20 7.5 150 0.3±0.03 R
LMK063 C6473[]P-F X6S 0.047 μ ±10, ±20 7.5 150 0.3±0.03 R
LMK063 C6683[]P-F X6S 0.068 μ ±10, ±20 10 150 0.3±0.03 R
LMK063 C6104[]P-F X6S 0.1 μ ±10, ±20 10 150 0.3±0.03 R
LMK063 C6224[]P-F X6S 0.22 μ ±10, ±20 10 150 0.3±0.03 R
LMK063BC6474[]PLF X6S 0.47 μ ±10, ±20 10 150 0.3±0.09 R
JMK063 C6223[]P-F X6S 0.022 μ ±10, ±20 7.5 200 0.3±0.03 R
JMK063 C6333[]P-F X6S 0.033 μ ±10, ±20 7.5 150 0.3±0.03 R
JMK063 C6473[]P-F X6S 0.047 μ ±10, ±20 7.5 150 0.3±0.03 R
JMK063 C6683[]P-F X6S 0.068 μ ±10, ±20 10 150 0.3±0.03 R
JMK063 C6104[]P-F X6S 0.1 μ ±10, ±20 10 150 0.3±0.03 R
JMK063 C6224[]P-F X6S 0.22 μ ±10, ±20 10 150 0.3±0.03 R
JMK063BC6474[]P-F X6S 0.47 μ ±10, ±20 10 150 0.3±0.09 R
JMK063BC6105MP-F X6S 1 μ ±20 10 150 0.3±0.09 R
AMK063 C6474[]P-F X6S 0.47 μ ±10, ±20 10 150 0.3±0.03 R
AMK063AC6105[]P-F X6S 1 μ ±10, ±20 10 150 0.3±0.05 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
25
16
10
6.3
4
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
10
6.3
4
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
16
1
8
■PARTS NUMBER
【Temperature Characteristic B7 : X7R】　0.3mm thickness（P）
HTLT
Rated voltage x ％
UMK063 B7101[]P-F X7R 100 p ±10, ±20 3.5 200 0.3±0.03 R
UMK063 B7151[]P-F X7R 150 p ±10, ±20 3.5 200 0.3±0.03 R
UMK063 B7221[]P-F X7R 220 p ±10, ±20 3.5 200 0.3±0.03 R
UMK063 B7331[]P-F X7R 330 p ±10, ±20 3.5 200 0.3±0.03 R
UMK063 B7471[]P-F X7R 470 p ±10, ±20 3.5 200 0.3±0.03 R
UMK063 B7681[]P-F X7R 680 p ±10, ±20 3.5 200 0.3±0.03 R
UMK063 B7102[]P-F X7R 1000 p ±10, ±20 3.5 200 0.3±0.03 R
TMK063 B7152[]P-F X7R 1500 p ±10, ±20 5 200 0.3±0.03 R
TMK063 B7222[]P-F X7R 2200 p ±10, ±20 5 200 0.3±0.03 R
TMK063 B7332[]P-F X7R 3300 p ±10, ±20 5 200 0.3±0.03 R
TMK063 B7472[]P-F X7R 4700 p ±10, ±20 5 200 0.3±0.03 R
TMK063 B7682[]P-F X7R 6800 p ±10, ±20 5 200 0.3±0.03 R
TMK063 B7103[]P-F X7R 0.01 μ ±10, ±20 5 200 0.3±0.03 R
EMK063 B7152[]P-F X7R 1500 p ±10, ±20 5 200 0.3±0.03 R
EMK063 B7222[]P-F X7R 2200 p ±10, ±20 5 200 0.3±0.03 R
EMK063 B7332[]P-F X7R 3300 p ±10, ±20 5 200 0.3±0.03 R
EMK063 B7472[]P-F X7R 4700 p ±10, ±20 5 200 0.3±0.03 R
EMK063 B7682[]P-F X7R 6800 p ±10, ±20 5 200 0.3±0.03 R
EMK063 B7103[]P-F X7R 0.01 μ ±10, ±20 5 200 0.3±0.03 R
EMK063 B7223[]P-F X7R 0.022 μ ±10, ±20 7.5 150 0.3±0.03 R
●105TYPE
【Temperature Characteristic BJ : B/X5R】　0.5mm thickness（V）
HTLT
Rated voltage x ％
UMK105 BJ221[]V-F B X5R*1 220 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 BJ331[]V-F B X5R*1 330 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 BJ471[]V-F B X5R*1 470 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 BJ681[]V-F B X5R*1 680 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 BJ102[]V-F B X5R*1 1000 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 BJ152[]V-F B X5R*1 1500 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 BJ222[]V-F B X5R*1 2200 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 BJ332[]V-F B X5R*1 3300 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 BJ472[]V-F B X5R*1 4700 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 BJ682[]V-F B X5R*1 6800 p ±10, ±20 2.5 150 0.5±0.05 R
UMK105 BJ103[]V-F B X5R*1 0.01 μ ±10, ±20 3.5 200 0.5±0.05 R
UMK105 BJ104[]V-F X5R 0.1 μ ±10, ±20 10 150 0.5±0.05 R
UMK105 BJ224[]V-F X5R 0.22 μ ±10, ±20 10 150 0.5±0.05 R
UMK105ABJ474[]V-F X5R 0.47 μ ±10, ±20 10 150 0.5±0.10 R
UMK105CBJ105MV-F X5R 1 μ ±20 10 150 0.5+0.20/-0 R
GMK105 BJ104[]V-F B X5R 0.1 μ ±10, ±20 5 150 0.5±0.05 R
GMK105ABJ105[]V-F X5R 1 μ ±10, ±20 10 150 0.5±0.10 R
TMK105 BJ153[]V-F B X5R*1 0.015 μ ±10, ±20 3.5 200 0.5±0.05 R
TMK105 BJ223[]V-F B X5R*1 0.022 μ ±10, ±20 3.5 200 0.5±0.05 R
TMK105 BJ333[]V-F B X5R*1 0.033 μ ±10, ±20 3.5 150 0.5±0.05 R
TMK105 BJ473[]V-F B X5R*1 0.047 μ ±10, ±20 3.5 150 0.5±0.05 R
TMK105 BJ104[]V-F B X5R 0.1 μ ±10, ±20 5 150 0.5±0.05 R
TMK105 BJ224[]V-F X5R 0.22 μ ±10, ±20 10 200 0.5±0.05 R
TMK105ABJ474[]V-F X5R 0.47 μ ±10, ±20 10 200 0.5±0.10 R
TMK105 BJ105[]V-F X5R 1 μ ±10, ±20 10 150 0.5±0.05 R
TMK105CBJ225[]V-F X5R 2.2 μ ±10, ±20 10 150 0.5+0.20/-0 R
EMK105 BJ153[]V-F B X5R*1 0.015 μ ±10, ±20 3.5 200 0.5±0.05 R
EMK105 BJ223[]V-F B X5R*1 0.022 μ ±10, ±20 3.5 200 0.5±0.05 R
EMK105 BJ333[]V-F B X5R*1 0.033 μ ±10, ±20 3.5 200 0.5±0.05 R
EMK105 BJ473[]V-F B X5R*1 0.047 μ ±10, ±20 3.5 200 0.5±0.05 R
EMK105 BJ683[]V-F B X5R 0.068 μ ±10, ±20 5 200 0.5±0.05 R
EMK105 BJ104[]V-F B X5R*1 0.1 μ ±10, ±20 5 150 0.5±0.05 R
EMK105 BJ224[]V-F B X5R 0.22 μ ±10, ±20 5 150 0.5±0.05 R
EMK105ABJ474[]V-F X5R 0.47 μ ±10, ±20 10 200 0.5±0.10 R
EMK105 BJ105[]V-F X5R 1 μ ±10, ±20 10 150 0.5±0.05 R
EMK105ABJ225[]V-F X5R 2.2 μ ±10, ±20 10 150 0.5±0.10 R
LMK105 BJ104[]V-F B X5R 0.1 μ ±10, ±20 5 200 0.5±0.05 R
LMK105 BJ224[]V-F B X5R 0.22 μ ±10, ±20 5 150 0.5±0.05 R
LMK105 BJ474[]V-F X5R 0.47 μ ±10, ±20 10 150 0.5±0.05 R
LMK105 BJ105[]V-F X5R 1 μ ±10, ±20 10 150 0.5±0.05 R
LMK105 BJ225[]V-F X5R 2.2 μ ±10, ±20 10 150 0.5±0.05 R
LMK105BBJ475MVLF X5R 4.7 μ ±20 10 150 0.5+0.15/-0.05 R
JMK105 BJ224[]V-F B X5R 0.22 μ ±10, ±20 5 150 0.5±0.05 R
JMK105 BJ474[]V-F X5R 0.47 μ ±10, ±20 10 150 0.5±0.05 R
JMK105 BJ105[]V-F X5R 1 μ ±10, ±20 10 150 0.5±0.05 R
JMK105 BJ225[]V-F X5R 2.2 μ ±10, ±20 10 150 0.5±0.05 R
JMK105BBJ475MV-F JMK105 BJ475MV-FD X5R 4.7 μ ±20 10 150 0.5+0.15/-0.05 R
JMK105CBJ106MV-F X5R 10 μ ±20 10 150 0.5+0.20/-0 R
AMK105ABJ475MV-F AMK105 BJ475MV-F X5R 4.7 μ ±20 10 150 0.5±0.10 R
AMK105CBJ106MV-F X5R 10 μ ±20 10 150 0.5+0.20/-0 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
25
16
16
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
35
25
10
6.3
4
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
17
1
8
■PARTS NUMBER
【Temperature Characteristic BJ : B/X5R】　0.3mm thickness（P）
HTLT
Rated voltage x ％
UMK105 BJ104[]P-F 50 X5R 0.1 μ ±10, ±20 10 150 0.3±0.03 R
TMK105 BJ103[]P-F B X5R 0.01 μ ±10, ±20 5 150 0.3±0.03 R
TMK105 BJ104[]P-F X5R 0.1 μ ±10, ±20 10 150 0.3±0.03 R
TMK105 BJ224[]P-F X5R 0.22 μ ±10, ±20 10 150 0.3±0.03 R
TMK105 BJ474[]P-F X5R 0.47 μ ±10, ±20 10 150 0.3±0.03 R
EMK105 BJ474[]P-F 16 X5R 0.47 μ ±10, ±20 10 150 0.3±0.03 R
LMK105 BJ105[]PLF 10 X5R 1 μ ±10, ±20 10 150 0.3±0.03 R
JMK105 BJ105[]P-F 6.3 X5R 1 μ ±10, ±20 10 150 0.3±0.03 R
AMK105 BJ225MP-F 4 X5R 2.2 μ ±20 10 150 0.3±0.03 R
【Temperature Characteristic BJ : X5R】　0.2mm thickness（C）
HTLT
Rated voltage x ％
LMK105 BJ104[]C-F 10 X5R 0.1 μ ±10, ±20 10 150 0.2±0.02 R
JMK105 BJ224[]C-F X5R 0.22 μ ±10, ±20 10 150 0.2±0.02 R
JMK105 BJ474[]C-F X5R 0.47 μ ±10, ±20 10 150 0.2±0.02 R
JMK105 BJ105MC-F X5R 1 μ ±20 10 150 0.2±0.02 R
【Temperature Characteristic BJ : X5R】　0.18mm thickness（E）
HTLT
Rated voltage x ％
LMK105 BJ104[]E-R 10 X5R 0.1 μ ±10, ±20 10 150 0.18±0.02 R
JMK105 BJ224[]E-R X5R 0.22 μ ±10, ±20 10 150 0.18±0.02 R
JMK105 BJ474[]E-R X5R 0.47 μ ±10, ±20 10 150 0.18±0.02 R
AMK105 BJ105ME-R 4 X5R 1 μ ±20 10 150 0.18±0.02 R
【Temperature Characteristic BJ : X5R】　0.13mm thickness（H）
HTLT
Rated voltage x ％
LMK105 BJ104MH-R 10 X5R 0.1 μ ±20 10 150 0.13±0.02 R
JMK105 BJ224MH-R 6.3 X5R 0.22 μ ±20 10 150 0.13±0.02 R
AMK105 BJ474MH-R 4 X5R 0.47 μ ±20 10 150 0.13±0.02 R
【Temperature Characteristic C6 : X6S】　0.5mm thickness（V）
HTLT
Rated voltage x ％
GMK105CC6105MV-F 35 X6S 1 μ ±20 10 150 0.5+0.20/-0 R
TMK105AC6105[]V-F 25 X6S 1 μ ±10, ±20 10 150 0.5±0.10 R
EMK105 C6105[]V-F X6S 1 μ ±10, ±20 10 150 0.5±0.05 R
EMK105CC6225MV-F X6S 2.2 μ ±20 10 150 0.5+0.20/-0 R
LMK105 C6105[]V-F X6S 1 μ ±10, ±20 10 200 0.5±0.05 R
LMK105AC6225MV-F X6S 2.2 μ ±20 10 150 0.5±0.10 R
JMK105 C6105[]V-F X6S 1 μ ±10, ±20 10 150 0.5±0.05 R
JMK105 C6225MV-F X6S 2.2 μ ±20 10 150 0.5±0.05 R
JMK105BC6475MV-F X6S 4.7 μ ±20 10 150 0.5+0.15/-0.05 R
AMK105BC6475MV-F 4 X6S 4.7 μ ±20 10 200 0.5+0.15/-0.05 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
25
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
6.3
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
6.3
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
16
10
6.3
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
18
1
8
■PARTS NUMBER
【Temperature Characteristic B7 : X7R】　0.5mm thickness（V）
HTLT
Rated voltage x ％
UMK105 B7221[]V-F X7R 220 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 B7331[]V-F X7R 330 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 B7471[]V-F X7R 470 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 B7681[]V-F X7R 680 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 B7102[]V-F X7R 1000 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 B7152[]V-F X7R 1500 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 B7222[]V-F X7R 2200 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 B7332[]V-F X7R 3300 p ±10, ±20 2.5 200 0.5±0.05 R
UMK105 B7472[]V-F X7R 4700 p ±10, ±20 2.5 150 0.5±0.05 R
UMK105 B7682[]V-F X7R 6800 p ±10, ±20 2.5 150 0.5±0.05 R
UMK105 B7103[]V-F X7R 0.01 μ ±10, ±20 3.5 150 0.5±0.05 R
UMK105 B7223[]V-FR X7R 0.022 μ ±10, ±20 10 200 0.5±0.05 R
UMK105 B7473[]V-FR X7R 0.047 μ ±10, ±20 10 200 0.5±0.05 R
UMK105 B7104[]V-FR X7R 0.1 μ ±10, ±20 10 150 0.5±0.05 R
TMK105 B7152[]V-F X7R 1500 p ±10, ±20 2.5 200 0.5±0.05 R
TMK105 B7222[]V-F X7R 2200 p ±10, ±20 2.5 200 0.5±0.05 R
TMK105 B7332[]V-F X7R 3300 p ±10, ±20 2.5 200 0.5±0.05 R
TMK105 B7472[]V-F X7R 4700 p ±10, ±20 2.5 200 0.5±0.05 R
TMK105 B7682[]V-F X7R 6800 p ±10, ±20 2.5 200 0.5±0.05 R
TMK105 B7103[]V-F X7R 0.01 μ ±10, ±20 3.5 200 0.5±0.05 R
TMK105 B7223[]V-F X7R 0.022 μ ±10, ±20 3.5 150 0.5±0.05 R
TMK105 B7473[]V-F X7R 0.047 μ ±10, ±20 3.5 150 0.5±0.05 R
TMK105 B7104[]V-FR X7R 0.1 μ ±10, ±20 10 200 0.5±0.05 R
TMK105 B7224[]V-FR X7R 0.22 μ ±10, ±20 10 150 0.5±0.05 R
EMK105 B7223[]V-F X7R 0.022 μ ±10, ±20 3.5 200 0.5±0.05 R
EMK105 B7473[]V-F X7R 0.047 μ ±10, ±20 3.5 200 0.5±0.05 R
EMK105 B7104[]V-F X7R 0.1 μ ±10, ±20 5 150 0.5±0.05 R
EMK105 B7224[]V-FR X7R 0.22 μ ±10, ±20 10 150 0.5±0.05 R
LMK105 B7223[]V-F X7R 0.022 μ ±10, ±20 3.5 200 0.5±0.05 R
LMK105 B7473[]V-F X7R 0.047 μ ±10, ±20 3.5 200 0.5±0.05 R
LMK105 B7104[]V-F X7R 0.1 μ ±10, ±20 5 150 0.5±0.05 R
LMK105 B7224[]V-FR X7R 0.22 μ ±10, ±20 10 150 0.5±0.05 R
LMK105 B7474[]V-F X7R 0.47 μ ±10, ±20 10 150 0.5±0.05 R
JMK105 B7224[]V-F X7R 0.22 μ ±10, ±20 5 150 0.5±0.05 R
JMK105 B7474[]V-F X7R 0.47 μ ±10, ±20 10 150 0.5±0.05 R
●107TYPE
【Temperature Characteristic BJ : B/X5R】　0.8mm thickness（A）
HTLT
Rated voltage x ％
UMK107ABJ474[]A-T UMK107 BJ474[]A-TD X5R 0.47 μ ±10, ±20 10 150 0.8+0.15/-0.05 R
UMK107 BJ105[]A-T X5R 1 μ ±10, ±20 10 150 0.8±0.10 R
UMK107BBJ225[]A-T X5R 2.2 μ ±10, ±20 10 150 0.8+0.20/-0 R
GMK107 BJ105[]A-T 35 B X5R 1 μ ±10, ±20 5 150 0.8±0.10 R
TMK107 BJ224[]A-T B X5R 0.22 μ ±10, ±20 3.5 200 0.8±0.10 R/W
TMK107 BJ474[]A-T B X5R 0.47 μ ±10, ±20 3.5 150 0.8±0.10 R
TMK107 BJ105[]A-T B X5R 1 μ ±10, ±20 5 150 0.8±0.10 R
TMK107ABJ225[]A-T TMK107 BJ225[]A-TD X5R 2.2 μ ±10, ±20 10 150 0.8+0.15/-0.05 R
TMK107BBJ475[]A-T X5R 4.7 μ ±10, ±20 10 150 0.8+0.20/-0 R
TMK107BBJ106MA-T X5R 10 μ ±20 10 150 0.8+0.20/-0 R
EMK107 BJ224[]A-T B X5R*1 0.22 μ ±10, ±20 3.5 200 0.8±0.10 R/W
EMK107 BJ474[]A-T B X5R*1 0.47 μ ±10, ±20 3.5 200 0.8±0.10 R
EMK107 BJ105[]A-T B X5R*1 1 μ ±10, ±20 5 150 0.8±0.10 R
EMK107 BJ225[]A-T B X5R 2.2 μ ±10, ±20 10 150 0.8±0.10 R
EMK107ABJ475[]A-T EMK107 BJ475[]A-TD X5R 4.7 μ ±10, ±20 10 150 0.8+0.15/-0.05 R
EMK107BBJ106MA-T X5R 10 μ ±20 10 150 0.8+0.20/-0 R
LMK107 BJ224[]A-T B X5R*1 0.22 μ ±10, ±20 3.5 200 0.8±0.10 R/W
LMK107 BJ474[]A-T B X5R*1 0.47 μ ±10, ±20 3.5 200 0.8±0.10 R
LMK107 BJ105[]A-T B X5R*1 1 μ ±10, ±20 5 200 0.8±0.10 R
LMK107 BJ225[]A-T B X5R 2.2 μ ±10, ±20 10 150 0.8±0.10 R
LMK107 BJ475[]A-T X5R 4.7 μ ±10, ±20 10 150 0.8±0.10 R
LMK107BBJ106[]ALT LMK107 BJ106[]ALTD X5R 10 μ ±10, ±20 10 150 0.8+0.20/-0 R
LMK107BBJ226MA-T X5R 22 μ ±20 10 150 0.8+0.20/-0 R
JMK107 BJ225[]A-T B X5R 2.2 μ ±10, ±20 10 150 0.8±0.10 R
JMK107 BJ475[]A-T X5R 4.7 μ ±10, ±20 10 150 0.8±0.10 R
JMK107ABJ106[]A-T JMK107 BJ106[]A-T X5R 10 μ ±10, ±20 10 150 0.8+0.15/-0.05 R
JMK107BBJ226MA-T X5R 22 μ ±20 10 150 0.8+0.20/-0 R
AMK107 BJ106MA-T X5R 10 μ ±20 10 150 0.8±0.10 R
AMK107BBJ226MA-T AMK107 BJ226MA-T X5R 22 μ ±20 10 150 0.8+0.20/-0 R
【Temperature Characteristic BJ : B/X5R】　0.45mm thickness（K）
HTLT
Rated voltage x ％
TMK107 BJ105[]K-T 25 X5R 1 μ ±10, ±20 10 150 0.45±0.05 R
EMK107 BJ105[]K-T X5R 1 μ ±10, ±20 10 150 0.45±0.05 R
EMK107BBJ225[]K-T X5R 2.2 μ ±10, ±20 10 150 0.45±0.05 R
LMK107 BJ105[]K-T B X5R 1 μ ±10, ±20 10 150 0.45±0.05 R
LMK107 BJ225[]K-T X5R 2.2 μ ±10, ±20 10 150 0.45±0.05 R
LMK107BBJ475MKLT LMK107 BJ475MKLTD X5R 4.7 μ ±20 10 150 0.45±0.05 R
JMK107 BJ105[]K-T B X5R 1 μ ±10, ±20 10 150 0.45±0.05 R
JMK107 BJ225[]K-T X5R 2.2 μ ±10, ±20 10 150 0.45±0.05 R
JMK107 BJ475MK-T X5R 4.7 μ ±20 10 150 0.45±0.05 R
JMK107BBJ106MK-TT X5R 10 μ ±20 10 150 0.45±0.05 R
AMK107BBJ106MK-T*2 4 X5R 10 μ ±20 10 150 0.45±0.05 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
25
16
10
6.3
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
25
16
10
6.3
4
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
16
10
6.3
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
19
1
8
■PARTS NUMBER
【Temperature Characteristic C6 : X6S】　0.8mm thickness（A）
HTLT
Rated voltage x ％
TMK107BC6225[]A-T 25 X6S 2.2 μ ±10, ±20 10 150 0.8+0.20/-0 R
EMK107 C6105[]A-T X6S 1 μ ±10, ±20 5 150 0.8±0.10 R
EMK107BC6225[]A-T X6S 2.2 μ ±10, ±20 10 150 0.8+0.20/-0 R
EMK107BC6475[]A-T X6S 4.7 μ ±10, ±20 10 150 0.8+0.20/-0 R
EMK107BC6106MA-T X6S 10 μ ±20 10 150 0.8+0.20/-0 R
LMK107 C6105[]A-T X6S 1 μ ±10, ±20 5 150 0.8±0.10 R
LMK107AC6475[]A-T X6S 4.7 μ ±10, ±20 10 150 0.8+0.15/-0.05 R
LMK107BC6106MA-T X6S 10 μ ±20 10 150 0.8+0.20/-0 R
JMK107 C6105[]A-T X6S 1 μ ±10, ±20 5 150 0.8±0.10 R
JMK107 C6475[]A-T X6S 4.7 μ ±10, ±20 10 150 0.8±0.10 R
JMK107BC6106MA-T X6S 10 μ ±20 10 150 0.8+0.20/-0 R
JMK107BC6226MA-T X6S 22 μ ±20 10 150 0.8+0.20/-0 R
AMK107AC6106MA-T X6S 10 μ ±20 10 150 0.8+0.15/-0.05 R
AMK107BC6226MA-T X6S 22 μ ±20 10 150 0.8+0.20/-0 R
【Temperature Characteristic B7 : X7R】　0.8mm thickness（A）
HTLT
Rated voltage x ％
UMK107 B7224[]A-TR X7R 0.22 μ ±10, ±20 10 150 0.8±0.10 R
UMK107 B7474[]A-TR X7R 0.47 μ ±10, ±20 10 150 0.8±0.10 R
UMK107AB7105[]A-T X7R 1 μ ±10, ±20 10 150 0.8+0.15/-0.05 R
TMK107 B7474[]A-TR X7R 0.47 μ ±10, ±20 10 150 0.8±0.10 R
TMK107 B7105[]A-T X7R 1 μ ±10, ±20 10 150 0.8±0.10 R
EMK107 B7224[]A-T X7R 0.22 μ ±10, ±20 3.5 150 0.8±0.10 R/W
EMK107 B7474[]A-T X7R 0.47 μ ±10, ±20 3.5 150 0.8±0.10 R
EMK107 B7105[]A-T X7R 1 μ ±10, ±20 5 150 0.8±0.10 R
EMK107BB7225[]A-T X7R 2.2 μ ±10, ±20 10 150 0.8+0.20/-0 R
LMK107 B7224[]A-T X7R 0.22 μ ±10, ±20 3.5 200 0.8±0.10 R/W
LMK107 B7474[]A-T X7R 0.47 μ ±10, ±20 3.5 200 0.8±0.10 R
LMK107 B7105[]A-T X7R 1 μ ±10, ±20 5 150 0.8±0.10 R
LMK107 B7225[]A-TR X7R 2.2 μ ±10, ±20 10 150 0.8±0.10 R
JMK107 B7224[]A-T X7R 0.22 μ ±10, ±20 3.5 200 0.8±0.10 R/W
JMK107 B7474[]A-T X7R 0.47 μ ±10, ±20 3.5 200 0.8±0.10 R
JMK107 B7105[]A-T X7R 1 μ ±10, ±20 5 150 0.8±0.10 R
JMK107 B7225[]A-TR X7R 2.2 μ ±10, ±20 10 200 0.8±0.10 R
JMK107BB7475[]A-T X7R 4.7 μ ±10, ±20 10 150 0.8+0.20/-0 R
●212TYPE
【Temperature Characteristic BJ : B/X5R】　1.25mm thickness（G）
HTLT
Rated voltage x ％
UMK212 BJ104[]G-T B X5R*1 0.1 μ ±10, ±20 3.5 200 1.25±0.10 R/W
UMK212 BJ224[]G-T B X5R*1 0.22 μ ±10, ±20 3.5 200 1.25±0.10 R/W
UMK212 BJ474[]G-T B X5R*1 0.47 μ ±10, ±20 3.5 150 1.25±0.10 R/W
UMK212 BJ105[]G-T B X5R 1 μ ±10, ±20 5 150 1.25±0.10 R/W
UMK212ABJ225[]G-T B X5R 2.2 μ ±10, ±20 10 150 1.25+0.15/-0.05 R
UMK212BBJ475[]G-T X5R 4.7 μ ±10, ±20 10 150 1.25+0.20/-0 R
GMK212BBJ106[]G-T 35 X5R 10 μ ±10, ±20 10 150 1.25+0.20/-0 R
TMK212 BJ225[]G-T B X5R 2.2 μ ±10, ±20 5 150 1.25±0.10 R
TMK212ABJ475[]G-T TMK212 BJ475[]G-T X5R 4.7 μ ±10, ±20 10 150 1.25+0.15/-0.05 R
TMK212BBJ106MG-T X5R 10 μ ±20 10 150 1.25+0.20/-0 R
TMK212BBJ226MG-TT X5R 22 μ ±20 10 150 1.25+0.20/-0 R
EMK212 BJ225[]G-T B X5R*1 2.2 μ ±10, ±20 5 200 1.25±0.10 R
EMK212ABJ475[]G-T EMK212 BJ475[]G-T B X5R*1 4.7 μ ±10, ±20 5 150 1.25+0.15/-0.05 R
EMK212ABJ106[]G-T EMK212 BJ106[]G-T X5R 10 μ ±10, ±20 10 150 1.25+0.15/-0.05 R
EMK212BBJ226MG-T X5R 22 μ ±20 10 150 1.25+0.20/-0 R
LMK212 BJ225[]G-T B X5R*1 2.2 μ ±10, ±20 5 200 1.25±0.10 R
LMK212ABJ475[]G-T LMK212 BJ475[]G-T B X5R*1 4.7 μ ±10, ±20 5 200 1.25+0.15/-0.05 R
LMK212ABJ106[]G-T LMK212 BJ106[]G-T X5R 10 μ ±10, ±20 10 200 1.25+0.15/-0.05 R
LMK212BBJ226MG-T LMK212 BJ226MG-T X5R 22 μ ±20 10 150 1.25+0.20/-0 R
LMK212BBJ476MG-T X5R 47 μ ±20 10 150 1.25+0.20/-0 R
JMK212ABJ475[]G-T JMK212 BJ475[]G-T B X5R 4.7 μ ±10, ±20 5 200 1.25+0.15/-0.05 R
JMK212ABJ106[]G-T JMK212 BJ106[]G-T X5R*1 10 μ ±10, ±20 10 200 1.25+0.15/-0.05 R
JMK212ABJ226MG-T JMK212 BJ226MG-T X5R 22 μ ±20 10 150 1.25+0.15/-0.05 R
JMK212BBJ476MG-T JMK212 BJ476MG-T X5R 47 μ ±20 10 150 1.25+0.20/-0 R
PMK212BBJ107MG-T 2.5 X5R 100 μ ±20 10 150 1.25+0.20/-0 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
16
10
6.3
4
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
25
16
10
6.3
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
25
16
10
6.3
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
20
1
8
■PARTS NUMBER
【Temperature Characteristic BJ : B/X5R】　0.85mm thickness（D）
HTLT
Rated voltage x ％
UMK212ABJ105[]D-T UMK212 BJ105[]D-TD X5R 1 μ ±10, ±20 10 150 0.85±0.10 R
UMK212BBJ225[]D-T X5R 2.2 μ ±10, ±20 10 150 0.85±0.10 R
GMK212BBJ475[]D-T 35 X5R 4.7 μ ±10, ±20 10 150 0.85±0.10 R
TMK212 BJ474[]D-T B X5R 0.47 μ ±10, ±20 3.5 200 0.85±0.10 R
TMK212 BJ105[]D-T B X5R 1 μ ±10, ±20 5 200 0.85±0.10 R
TMK212ABJ225[]D-T TMK212 BJ225[]D-T B X5R 2.2 μ ±10, ±20 5 150 0.85±0.10 R
TMK212BBJ475[]D-T TMK212 BJ475[]D-TD X5R 4.7 μ ±10, ±20 10 150 0.85±0.1
0R
TMK212BBJ106[]D-T X5R 10 μ ±10, ±20 10 150 0.85±0.10 R
EMK212 BJ105[]D-T B X5R*1 1 μ ±10, ±20 5 200 0.85±0.10 R
EMK212ABJ225[]D-T EMK212 BJ225[]D-T B X5R*1 2.2 μ ±10, ±20 5 200 0.85±0.10 R
EMK212 BJ475[]D-T B X5R 4.7 μ ±10, ±20 10 150 0.85±0.10 R
EMK212ABJ106[]D-T EMK212 BJ106[]D-TD X5R 10 μ ±10, ±20 10 150 0.85±0.10 R
LMK212 BJ105[]D-T B X5R*1 1 μ ±10, ±20 3.5 200 0.85±0.10 R
LMK212 BJ225[]D-T B X5R*1 2.2 μ ±10, ±20 5 200 0.85±0.10 R
LMK212ABJ106[]D-T LMK212 BJ106[]D-T X5R 10 μ ±10, ±20 10 150 0.85±0.10 R
LMK212BBJ226MD-T X5R 22 μ ±20 10 150 0.85±0.10 R
JMK212ABJ106[]D-T JMK212 BJ106[]D-T X5R 10 μ ±10, ±20 10 200 0.85±0.10 R
JMK212ABJ226MD-T JMK212 BJ226MD-T X5R 22 μ ±20 10 150 0.85±0.10 R
AMK212BBJ476MD-T 4 X5R 47 μ ±20 10 150 0.85±0.10 R
【Temperature Characteristic BJ : X5R】　0.45mm thickness（K）
HTLT
Rated voltage x ％
TMK212BBJ225[]K-T 25 X5R 2.2 μ ±10, ±20 10 150 0.45±0.05 R
EMK212BBJ475[]K-T 16 X5R 4.7 μ ±10, ±20 10 150 0.45±0.05 R
LMK212ABJ475[]K-T LMK212 BJ475[]K-T 10 X5R 4.7 μ ±10, ±20 10 150 0.45±0.05 R
JMK212ABJ475[]K-T JMK212 BJ475[]K-T X5R 4.7 μ ±10, ±20 10 150 0.45±0.05 R
JMK212ABJ106MK-T *2 JMK212 BJ106MK-T X5R 10 μ ±20 10 150 0.45±0.05 R
【Temperature Characteristic C6 : X6S】　1.25mm thickness（G）
HTLT
Rated voltage x ％
EMK212BC6226MG-TT 16 X6S 22 μ ±20 10 150 1.25+0.20/-0 R
LMK212BC6226MG-T 10 X6S 22 μ ±20 10 150 1.25+0.20/-0 R
JMK212BC6226MG-T X6S 22 μ ±20 10 150 1.25+0.20/-0 R
JMK212BC6476MG-T X6S 47 μ ±20 10 150 1.25+0.20/-0 R
AMK212AC6226MG-T X6S 22 μ ±20 10 150 1.25+0.15/-0.05 R
AMK212BC6476MG-T X6S 47 μ ±20 10 150 1.25+0.20/-0 R
【Temperature Characteristic C6 : X6S】　0.85mm thickness（D）
HTLT
Rated voltage x ％
LMK212AC6106[]D-T 10 X6S 10 μ ±10, ±20 10 150 0.85±0.10 R
AMK212BC6226MD-T 4 X6S 22 μ ±20 10 150 0.85±0.10 R
【Temperature Characteristic B7 : X7R】　1.25mm thickness（G）
HTLT
Rated voltage x ％
UMK212 B7104[]G-T X7R 0.1 μ ±10, ±20 3.5 200 1.25±0.10 R/W
UMK212 B7224[]G-T X7R 0.22 μ ±10, ±20 3.5 150 1.25±0.10 R/W
UMK212 B7474[]G-T X7R 0.47 μ ±10, ±20 3.5 150 1.25±0.10 R/W
UMK212 B7105[]G-T X7R 1 μ ±10, ±20 10 150 1.25±0.10 R/W
UMK212BB7225[]G-T X7R 2.2 μ ±10, ±20 10 150 1.25+0.20/-0 R
GMK212 B7105[]G-T 35 X7R 1 μ ±10, ±20 3.5 150 1.25±0.10 R/W
TMK212 B7105[]G-T X7R 1 μ ±10, ±20 3.5 150 1.25±0.10 R
TMK212 B7225[]G-TR X7R 2.2 μ ±10, ±20 10 150 1.25±0.10 R
TMK212AB7475[]G-T TMK212 B7475[]G-T X7R 4.7 μ ±10, ±20 10 150 1.25+0.15/-0.05 R
EMK212 B7105[]G-T X7R 1 μ ±10, ±20 3.5 200 1.25±0.10 R/W
EMK212 B7225[]G-T X7R 2.2 μ ±10, ±20 10 150 1.25±0.10 R
EMK212 B7475[]G-T X7R 4.7 μ ±10, ±20 10 150 1.25±0.10 R
EMK212BB7106MG-T X7R 10 μ ±20 10 150 1.25+0.20/-0 R
LMK212 B7105[]G-T X7R 1 μ ±10, ±20 3.5 200 1.25±0.10 R/W
LMK212 B7225[]G-T X7R 2.2 μ ±10, ±20 5 200 1.25±0.10 R
LMK212 B7475[]G-T X7R 4.7 μ ±10, ±20 10 150 1.25±0.10 R
LMK212AB7106[]G-T LMK212 B7106[]G-TD X7R 10 μ ±10, ±20 10 150 1.25+0.15/-0.05 R
JMK212AB7106[]G-T JMK212 B7106[]G-T 6.3 X7R 10 μ ±10, ±20 10 150 1.25+0.15/-0.05 R
【Temperature Characteristic B7 : X7R】　0.85mm thickness（D）
HTLT
Rated voltage x ％
UMK212AB7104[]D-T X7R 0.1 μ ±10, ±20 10 150 0.85±0.10 R
UMK212AB7224[]D-T X7R 0.22 μ ±10, ±20 10 150 0.85±0.10 R
UMK212AB7474[]D-T X7R 0.47 μ ±10, ±20 10 150 0.85±0.10 R
UMK212AB7105[]D-T X7R 1 μ ±10, ±20 10 150 0.85±0.10 R
TMK212AB7225[]D-TR 25 X7R 2.2 μ ±10, ±20 10 150 0.85±0.10 R
EMK212 B7474[]D-T X7R 0.47 μ ±10, ±20 3.5 200 0.85±0.10 R/W
EMK212 B7105[]D-T X7R 1 μ ±10, ±20 5 200 0.85±0.10 R
EMK212AB7225[]D-T EMK212 B7225[]D-T X7R 2.2 μ ±10, ±20 5 150 0.85±0.10 R
EMK212BB7475[]D-T X7R 4.7 μ ±10, ±20 10 150 0.85±0.10 R
LMK212 B7105[]D-T X7R 1 μ ±10, ±20 3.5 200 0.85±0.10 R
LMK212AB7225[]D-T LMK212 B7225[]D-T X7R 2.2 μ ±10, ±20 5 200 0.85±0.10 R
LMK212AB7475[]D-TR LMK212 B7475[]D-TR X7R 4.7 μ ±10, ±20 10 150 0.85±0.10 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
25
16
10
6.3
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
6.3
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
6.3
4
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
25
16
10
tanδ
[％]
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
16
10
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
21
1
8
■PARTS NUMBER
●316TYPE
【Temperature Characteristic BJ : B/X5R】　1.6mm thickness（L）
HTLT
Rated voltage x ％
UMK316 BJ105[]L-T B X5R*1 1 μ ±10, ±20 3.5 200 1.6±0.20 R
UMK316 BJ225[]L-T X5R 2.2 μ ±10, ±20 10 150 1.6±0.20 R
UMK316 BJ475[]L-T X5R 4.7 μ ±10, ±20 10 150 1.6±0.20 R
UMK316BBJ106[]L-T X5R 10 μ ±10, ±20 10 150 1.6±0.30 R
TMK316 BJ225[]L-T B X5R*1 2.2 μ ±10, ±20 3.5 200 1.6±0.20 R
TMK316 BJ475[]L-T B X5R 4.7 μ ±10, ±20 5 150 1.6±0.20 R
TMK316 BJ106[]L-T X5R*1 10 μ ±10, ±20 5 150 1.6±0.20 R
TMK316BBJ226ML-T X5R 22 μ ±20 10 150 1.6±0.30 R
EMK316 BJ225[]L-T B X5R*1 2.2 μ ±10, ±20 3.5 200 1.6±0.20 R/W
EMK316 BJ475[]L-T B X5R 4.7 μ ±10, ±20 5 200 1.6±0.20 R
EMK316 BJ106[]L-T B X5R*1 10 μ ±10, ±20 5 150 1.6±0.20 R
EMK316ABJ226[]L-T EMK316 BJ226[]L-T B X5R 22 μ ±10, ±20 10 150 1.6±0.20 R
LMK316 BJ106[]L-T B X5R*1 10 μ ±10, ±20 5 200 1.6±0.20 R
LMK316ABJ226[]L-T LMK316 BJ226[]L-T B X5R 22 μ ±10, ±20 10 150 1.6±0.20 R
LMK316ABJ476ML-T LMK316 BJ476ML-T X5R 47 μ ±20 10 150 1.6±0.20 R
LMK316BBJ107ML-T X5R 100 μ ±20 10 150 1.6±0.30 R
JMK316 BJ106[]L-T B X5R*1 10 μ ±10, ±20 5 200 1.6±0.20 R
JMK316ABJ226[]L-T JMK316 BJ226[]L-T B X5R 22 μ ±10, ±20 10 200 1.6±0.20 R
JMK316ABJ476ML-T JMK316 BJ476ML-T X5R 47 μ ±20 10 200 1.6±0.20 R
JMK316ABJ107ML-T JMK316 BJ107ML-T X5R 100 μ ±20 10 150 1.6±0.20 R
AMK316ABJ107ML-T AMK316 BJ107ML-T X5R 100 μ ±20 10 150 1.6±0.20 R
AMK316BBJ157ML-T X5R 150 μ ±20 10 150 1.6±0.30 R
PMK316BBJ227ML-T 2.5 X5R 220 μ ±20 10 150 1.6±0.30 R
【Temperature Characteristic BJ : B/X5R】　0.85mm thickness（D）
HTLT
Rated voltage x ％
UMK316 BJ105[]D-T B X5R 1 μ ±10, ±20 3.5 150 0.85±0.10 R
UMK316 BJ225[]D-T B X5R 2.2 μ ±10, ±20 3.5 150 0.85±0.10 R
UMK316ABJ475[]D-T UMK316 BJ475[]D-T X5R 4.7 μ ±10, ±20 10 150 0.85±0.10 R
TMK316 BJ105[]D-T B X5R 1 μ ±10, ±20 3.5 200 0.85±0.10 R
TMK316 BJ225[]D-T B X5R 2.2 μ ±10, ±20 3.5 150 0.85±0.10 R
TMK316 BJ475[]D-T X5R 4.7 μ ±10, ±20 5 150 0.85±0.10 R
TMK316ABJ106[]D-T TMK316 BJ106[]D-TD X5R 10 μ ±10, ±20 10 150 0.85±0.10 R
EMK316 BJ225[]D-T B X5R 2.2 μ ±10, ±20 3.5 200 0.85±0.10 R
EMK316 BJ475[]D-T B X5R 4.7 μ ±10, ±20 5 200 0.85±0.10 R
EMK316 BJ106[]D-T X5R 10 μ ±10, ±20 10 150 0.85±0.10 R
EMK316ABJ226MD-T EMK316 BJ226MD-T X5R 22 μ ±20 10 150 0.85±0.10 R
LMK316 BJ475[]D-T B X5R 4.7 μ ±10, ±20 5 200 0.85±0.10 R
LMK316 BJ106[]D-T B X5R 10 μ ±10, ±20 10 200 0.85±0.10 R
LMK316ABJ226MD-T LMK316 BJ226MD-T X5R 22 μ ±20 10 150 0.85±0.10 R
JMK316 BJ106[]D-T B X5R 10 μ ±10, ±20 10 200 0.85±0.10 R
JMK316ABJ226MD-T JMK316 BJ226MD-T X5R 22 μ ±20 10 150 0.85±0.10 R
JMK316ABJ476MD-T JMK316 BJ476MD-T X5R 47 μ ±20 10 150 0.85±0.10 R
【Temperature Characteristic C6 : X6S】　1.6mm thickness（L）
HTLT
Rated voltage x ％
EMK316BC6226ML-T 16 X6S 22 μ ±20 10 150 1.6±0.30 R
JMK316AC6476ML-T X6S 47 μ ±20 10 150 1.6±0.20 R
JMK316BC6107ML-T X6S 100 μ ±20 10 150 1.6±0.30 R
AMK316AC6476ML-T X6S 47 μ ±20 10 200 1.6±0.20 R
AMK316AC6107ML-T X6S 100 μ ±20 10 150 1.6±0.20 R
【Temperature Characteristic C7 : X7S】　1.6mm thickness（L）
HTLT
Rated voltage x ％
AMK316AC7476ML-T 4 X7S 47 μ ±20 10 150 1.6±0.20 R
【Temperature Characteristic B7 : X7R】　1.6mm thickness（L）
HTLT
Rated voltage x ％
UMK316 B7224[]L-T X7R 0.22 μ ±10, ±20 2.5 200 1.6±0.20 R/W
UMK316 B7474[]L-T X7R 0.47 μ ±10, ±20 3.5 200 1.6±0.20 R/W
UMK316 B7105[]L-T X7R 1 μ ±10, ±20 3.5 200 1.6±0.20 R
UMK316 B7225[]L-T X7R 2.2 μ ±10, ±20 10 150 1.6±0.20 R
UMK316AB7475[]L-T UMK316 B7475[]L-T X7R 4.7 μ ±10, ±20 10 150 1.6±0.20 R
GMK316AB7106[]L-TR 35 X7R 10 μ ±10, ±20 10 150 1.6±0.20 R
TMK316 B7105[]L-T X7R 1 μ ±10, ±20 3.5 200 1.6±0.20 R/W
TMK316 B7225[]L-T X7R 2.2 μ ±10, ±20 3.5 200 1.6±0.20 R
TMK316AB7475[]L-T TMK316 B7475[]L-T X7R 4.7 μ ±10, ±20 10 200 1.6±0.20 R
TMK316AB7106[]L-T TMK316 B7106[]L-TD X7R 10 μ ±10, ±20 10 150 1.6±0.20 R
EMK316 B7225[]L-T X7R 2.2 μ ±10, ±20 3.5 200 1.6±0.20 R/W
EMK316 B7475[]L-T X7R 4.7 μ ±10, ±20 5 200 1.6±0.20 R
EMK316AB7106[]L-T EMK316 B7106[]L-TD X7R 10 μ ±10, ±20 10 200 1.6±0.20 R
EMK316BB7226ML-T X7R 22 μ ±20 10 150 1.6±0.30 R
LMK316 B7225[]L-T X7R 2.2 μ ±10, ±20 3.5 200 1.6±0.20 R/W
LMK316 B7475[]L-T X7R 4.7 μ ±10, ±20 5 200 1.6±0.20 R
LMK316AB7106[]L-T LMK316 B7106[]L-TD X7R 10 μ ±10, ±20 10 200 1.6±0.20 R
LMK316AB7226[]L-TR LMK316 B7226[]Ｌ-TD X7R 22 μ ±10, ±20 10 150 1.6±0.20 R
JMK316 B7106[]L-T 6.3 X7R 10 μ ±10, ±20 5 200 1.6±0.20 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
25
16
10
6.3
4
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
25
16
10
6.3
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
6.3
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
25
16
10
4
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
22
1
8
■PARTS NUMBER
【Temperature Characteristic B7 : X7R】　0.85mm thickness（D）
HTLT
Rated voltage x ％
UMK316 B7225[]D-T 50 X7R 2.2 μ ±10, ±20 10 150 0.85±0.10 R
TMK316AB7475[]D-T 25 X7R 4.7 μ ±10, ±20 10 150 0.85±0.10 R
LMK316AB7106MD-T 10 X7R 10 μ ±20 10 150 0.85±0.10 R
●325TYPE
【Temperature Characteristic BJ : B/X5R】　2.5mm thickness（M）
HTLT
Rated voltage x ％
UMK325 BJ475[]M-P X5R 4.7 μ ±10, ±20 5 150 2.5±0.20 R
UMK325 BJ106[]M-P X5R 10 μ ±10, ±20 5 150 2.5±0.20 R
GMK325 BJ226MM-P 35 X5R 22 μ ±20 5 150 2.5±0.20 R
TMK325 BJ106[]M-P B X5R*1 10 μ ±10, ±20 3.5 150 2.5±0.20 R
TMK325 BJ226[]M-P X5R 22 μ ±10, ±20 5 150 2.5±0.20 R
TMK325ABJ476MM-P X5R 47 μ ±20 10 150 2.5±0.30 R
EMK325 BJ226[]M-P B X5R 22 μ ±10, ±20 5 150 2.5±0.20 R
EMK325 BJ476MM-P X5R 47 μ ±20 10 150 2.5±0.20 R
EMK325ABJ107MM-P X5R 100 μ ±20 10 150 2.5±0.30 R
LMK325 BJ226[]M-P B X5R 22 μ ±10, ±20 5 200 2.5±0.20 R
LMK325 BJ476MM-P X5R 47 μ ±20 10 150 2.5±0.20 R
LMK325ABJ107MM-P LMK325 BJ107MM-P X5R 100 μ ±20 10 150 2.5±0.30 R
LMK325ABJ227MM-PE X5R 220 μ ±20 10 150 2.5±0.30 R
JMK325 BJ476MM-P X5R 47 μ ±20 10 150 2.5±0.20 R
JMK325ABJ107MM-P JMK325 BJ107MM-P X5R 100 μ ±20 10 150 2.5±0.30 R
JMK325ABJ157MM-P X5R 150 μ ±20 10 150 2.5±0.30 R
JMK325ABJ227MM-P X5R 220 μ ±20 10 150 2.5±0.30 R
JMK325ABJ337MM-P X5R 330 μ ±20 10 150 2.5±0.30 R
AMK325ABJ157MM-P X5R 150 μ ±20 10 150 2.5±0.30 R
AMK325ABJ227MM-P X5R 220 μ ±20 10 150 2.5±0.30 R
AMK325ABJ337MM-P X5R 330 μ ±20 10 150 2.5±0.30 R
【Temperature Characteristic BJ : B/X5R】　1.9mm thickness（Y,N）
HTLT
Rated voltage x ％
UMK325 BJ475[]N-T 50 X5R 4.7 μ ±10, ±20 10 150 1.9±0.20 R
GMK325 BJ225[]N-T B X5R 2.2 μ ±10, ±20 3.5 200 1.9±0.20 R
GMK325 BJ475[]N-T X5R 4.7 μ ±10, ±20 10 150 1.9±0.20 R
GMK325 BJ106[]N-T B X5R 10 μ ±10, ±20 5 150 1.9±0.20 R
TMK325 BJ335MN-T B X5R*1 3.3 μ ±20 3.5 200 1.9±0.20 R
TMK325 BJ475[]N-T B X5R*1 4.7 μ ±10, ±20 3.5 200 1.9±0.20 R
TMK325 BJ106[]N-T B X5R 10 μ ±10, ±20 5 200 1.9±0.20 R
EMK325 BJ475[]N-T B X5R*1 4.7 μ ±10, ±20 3.5 200 1.9±0.20 R
EMK325 BJ106[]N-T B X5R 10 μ ±10, ±20 3.5 200 1.9±0.20 R
EMK325 BJ476MY-T X5R 47 μ ±20 10 150 1.9+0.1/-0.2 R
LMK325 BJ226MY-T B X5R 22 μ ±20 5 150 1.9+0.1/-0.2 R
LMK325 BJ106[]N-T B X5R 10 μ ±10, ±20 3.5 200 1.9±0.20 R
JMK325 BJ226MY-T B X5R 22 μ ±20 5 200 1.9+0.1/-0.2 R
JMK325 BJ107MY-T X5R 100 μ ±20 10 150 1.9+0.1/-0.2 R
JMK325 BJ476MN-T X5R 47 μ ±20 10 150 1.9±0.20 R
【Temperature Characteristic BJ : B/X5R】　0.85mm thickness（D）
HTLT
Rated voltage x ％
TMK325 BJ106[]D-T 25 B X5R 10 μ ±10, ±20 5 150 0.85±0.10 R
EMK325 BJ106[]D-T B X5R 10 μ ±10, ±20 5 150 0.85±0.10 R
EMK325 BJ226MD-T B X5R 22 μ ±20 10 150 0.85±0.10 R
LMK325 BJ335[]D-T B X5R 3.3 μ ±10, ±20 3.5 200 0.85±0.10 R
LMK325 BJ475[]D-T B X5R 4.7 μ ±10, ±20 5 200 0.85±0.10 R
LMK325 BJ106[]D-T B X5R 10 μ ±10, ±20 5 150 0.85±0.10 R
【Temperature Characteristic C6 : X6S】　2.5mm thickness（M）
HTLT
Rated voltage x ％
EMK325AC6476MM-P 16 X6S 47 μ ±20 10 150 2.5±0.30 R
LMK325AC6107MM-P 10 X6S 100 μ ±20 10 150 2.5±0.30 R
JMK325AC6227MM-PE X6S 220 μ ±20 10 150 2.5±0.30 R
JMK325AC6107MM-P X6S 100 μ ±20 10 150 2.5±0.30 R
AMK325AC6157MM-P X6S 150 μ ±20 10 150 2.5±0.30 R
AMK325AC6227MM-P X6S 220 μ ±20 10 150 2.5±0.30 R
AMK325AC6337MM-P X6S 330 μ ±20 10 150 2.5±0.30 R
PMK325AC6337MM-P 2.5 X6S 330 μ ±20 10 150 2.5±0.30 R
【Temperature Characteristic C7 : X7S】　2.5mm thickness（M）
HTLT
Rated voltage x ％
JMK325AC7107MM-P 6.3 X7S 100 μ ±20 10 150 2.5±0.30 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
25
16
10
6.3
4
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
35
25
16
10
6.3
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
16
10
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
6.3
4
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
23
1
8
■PARTS NUMBER
【Temperature Characteristic B7 : X7R】　2.5mm thickness（M）
HTLT
Rated voltage x ％
UMK325 B7335[]M-P X7R 3.3 μ ±10, ±20 3.5 200 2.5±0.20 R
UMK325 B7475[]M-P X7R 4.7 μ ±10, ±20 5 150 2.5±0.20 R
UMK325AB7106[]M-P X7R 10 μ ±10, ±20 10 150 2.5±0.30 R
TMK325AB7106[]M-P X7R 10 μ ±10, ±20 10 200 2.5±0.30 R
TMK325 B7226[]M-PR X7R 22 μ ±10, ±20 10 150 2.5±0.20 R
EMK325 B7226[]M-PR 16 X7R 22 μ ±10, ±20 10 150 2.5±0.20 R
LMK325 B7476[]M-PR 10 X7R 47 μ ±10, ±20 10 150 2.5±0.20 R
JMK325 B7476[]M-PR 6.3 X7R 47 μ ±10, ±20 10 200 2.5±0.20 R
【Temperature Characteristic B7 : X7R】　1.9mm thickness（N）
HTLT
Rated voltage x ％
UMK325 B7475[]N-TR 50 X7R 4.7 μ ±10, ±20 10 150 1.9±0.20 R
TMK325 B7335[]N-T X7R 3.3 μ ±10, ±20 3.5 200 1.9±0.20 R
TMK325 B7475[]N-T X7R 4.7 μ ±10, ±20 3.5 150 1.9±0.20 R
TMK325 B7106[]N-TR X7R 10 μ ±10, ±20 10 150 1.9±0.20 R
EMK325 B7475[]N-T X7R 4.7 μ ±10, ±20 3.5 200 1.9±0.20 R
EMK325 B7106[]N-T X7R 10 μ ±10, ±20 3.5 150 1.9±0.20 R
LMK325 B7106[]N-T 10 X7R 10 μ ±10, ±20 3.5 200 1.9±0.20 R
●432TYPE
【Temperature Characteristic BJ : X5R】　2.5mm thickness（M）
HTLT
Rated voltage x ％
AMK432 BJ477MM-T 4 X5R 470 μ ±20 10 150 2.5±0.20 R
【Temperature Characteristic C6 : X6S】　2.5mm thickness（M）
HTLT
Rated voltage x ％
PMK432 C6477MM-T 2.5 X6S 470 μ ±20 10 150 2.5±0.20 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
25
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
25
16
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
24
1
8
■PARTS NUMBER
Multilayer Ceramic Capacitors（Temperature compensating type）
●021TYPE
【Temperature Characteristic CG : CG/C0G】　0.125mm thickness（K）
HTLT
Rated voltage x ％
TMK021 CG0R2[]K-W CG C0G 0.2 p ±0.1pF, ±0.25pF 404 200 0.125±0.013 R
TMK021 CG0R3[]K-W CG C0G 0.3 p ±0.1pF, ±0.25pF 406 200 0.125±0.013 R
TMK021 CG0R4[]K-W CG C0G 0.4 p ±0.1pF, ±0.25pF 408 200 0.125±0.013 R
TMK021 CG0R5[]K-W CG C0G 0.5 p ±0.1pF, ±0.25pF 410 200 0.125±0.013 R
TMK021 CG0R6[]K-W CG C0G 0.6 p ±0.1pF, ±0.25pF 412 200 0.125±0.013 R
TMK021 CG0R7[]K-W CG C0G 0.7 p ±0.1pF, ±0.25pF 414 200 0.125±0.013 R
TMK021 CGR75[]K-W CG C0G 0.75 p ±0.1pF, ±0.25pF 415 200 0.125±0.013 R
TMK021 CG0R8[]K-W CG C0G 0.8 p ±0.1pF, ±0.25pF 416 200 0.125±0.013 R
TMK021 CG0R9[]K-W CG C0G 0.9 p ±0.1pF, ±0.25pF 418 200 0.125±0.013 R
TMK021 CG010[]K-W CG C0G 1 p ±0.1pF, ±0.25pF 420 200 0.125±0.013 R
TMK021 CG1R1[]K-W CG C0G 1.1 p ±0.1pF, ±0.25pF 422 200 0.125±0.013 R
TMK021 CG1R2[]K-W CG C0G 1.2 p ±0.1pF, ±0.25pF 424 200 0.125±0.013 R
TMK021 CG1R3[]K-W CG C0G 1.3 p ±0.1pF, ±0.25pF 426 200 0.125±0.013 R
TMK021 CG1R4[]K-W CG C0G 1.4 p ±0.1pF, ±0.25pF 428 200 0.125±0.013 R
TMK021 CG1R5[]K-W CG C0G 1.5 p ±0.1pF, ±0.25pF 430 200 0.125±0.013 R
TMK021 CG1R6[]K-W CG C0G 1.6 p ±0.1pF, ±0.25pF 432 200 0.125±0.013 R
TMK021 CG1R7[]K-W CG C0G 1.7 p ±0.1pF, ±0.25pF 434 200 0.125±0.013 R
TMK021 CG1R8[]K-W CG C0G 1.8 p ±0.1pF, ±0.25pF 436 200 0.125±0.013 R
TMK021 CG1R9[]K-W CG C0G 1.9 p ±0.1pF, ±0.25pF 438 200 0.125±0.013 R
TMK021 CG020[]K-W CG C0G 2 p ±0.1pF, ±0.25pF 440 200 0.125±0.013 R
TMK021 CG2R1[]K-W CG C0G 2.1 p ±0.1pF, ±0.25pF 442 200 0.125±0.013 R
TMK021 CG2R2[]K-W CG C0G 2.2 p ±0.1pF, ±0.25pF 444 200 0.125±0.013 R
TMK021 CG2R3[]K-W CG C0G 2.3 p ±0.1pF, ±0.25pF 446 200 0.125±0.013 R
TMK021 CG2R4[]K-W CG C0G 2.4 p ±0.1pF, ±0.25pF 448 200 0.125±0.013 R
TMK021 CG2R5[]K-W CG C0G 2.5 p ±0.1pF, ±0.25pF 450 200 0.125±0.013 R
TMK021 CG2R6[]K-W CG C0G 2.6 p ±0.1pF, ±0.25pF 452 200 0.125±0.013 R
TMK021 CG2R7[]K-W CG C0G 2.7 p ±0.1pF, ±0.25pF 454 200 0.125±0.013 R
TMK021 CG2R8[]K-W CG C0G 2.8 p ±0.1pF, ±0.25pF 456 200 0.125±0.013 R
TMK021 CG2R9[]K-W CG C0G 2.9 p ±0.1pF, ±0.25pF 458 200 0.125±0.013 R
TMK021 CG030[]K-W CG C0G 3 p ±0.1pF, ±0.25pF 460 200 0.125±0.013 R
TMK021 CG3R1[]K-W CG C0G 3.1 p ±0.1pF, ±0.25pF 462 200 0.125±0.013 R
TMK021 CG3R2[]K-W CG C0G 3.2 p ±0.1pF, ±0.25pF 464 200 0.125±0.013 R
TMK021 CG3R3[]K-W CG C0G 3.3 p ±0.1pF, ±0.25pF 466 200 0.125±0.013 R
TMK021 CG3R4[]K-W CG C0G 3.4 p ±0.1pF, ±0.25pF 468 200 0.125±0.013 R
TMK021 CG3R5[]K-W CG C0G 3.5 p ±0.1pF, ±0.25pF 470 200 0.125±0.013 R
TMK021 CG3R6[]K-W CG C0G 3.6 p ±0.1pF, ±0.25pF 472 200 0.125±0.013 R
TMK021 CG3R7[]K-W CG C0G 3.7 p ±0.1pF, ±0.25pF 474 200 0.125±0.013 R
TMK021 CG3R8[]K-W CG C0G 3.8 p ±0.1pF, ±0.25pF 476 200 0.125±0.013 R
TMK021 CG3R9[]K-W CG C0G 3.9 p ±0.1pF, ±0.25pF 478 200 0.125±0.013 R
TMK021 CG040[]K-W CG C0G 4 p ±0.1pF, ±0.25pF 480 200 0.125±0.013 R
TMK021 CG4R1[]K-W CG C0G 4.1 p ±0.1pF, ±0.25pF 482 200 0.125±0.013 R
TMK021 CG4R2[]K-W CG C0G 4.2 p ±0.1pF, ±0.25pF 484 200 0.125±0.013 R
TMK021 CG4R3[]K-W CG C0G 4.3 p ±0.1pF, ±0.25pF 486 200 0.125±0.013 R
TMK021 CG4R4[]K-W CG C0G 4.4 p ±0.1pF, ±0.25pF 488 200 0.125±0.013 R
TMK021 CG4R5[]K-W CG C0G 4.5 p ±0.1pF, ±0.25pF 490 200 0.125±0.013 R
TMK021 CG4R6[]K-W CG C0G 4.6 p ±0.1pF, ±0.25pF 492 200 0.125±0.013 R
TMK021 CG4R7[]K-W CG C0G 4.7 p ±0.1pF, ±0.25pF 494 200 0.125±0.013 R
TMK021 CG4R8[]K-W CG C0G 4.8 p ±0.1pF, ±0.25pF 496 200 0.125±0.013 R
TMK021 CG4R9[]K-W CG C0G 4.9 p ±0.1pF, ±0.25pF 498 200 0.125±0.013 R
TMK021 CG050[]K-W CG C0G 5 p ±0.1pF, ±0.25pF 500 200 0.125±0.013 R
TMK021 CG5R1[]K-W CG C0G 5.1 p ±0.25pF, ±0.5pF 502 200 0.125±0.013 R
TMK021 CG5R2[]K-W CG C0G 5.2 p ±0.25pF, ±0.5pF 504 200 0.125±0.013 R
TMK021 CG5R3[]K-W CG C0G 5.3 p ±0.25pF, ±0.5pF 506 200 0.125±0.013 R
TMK021 CG5R4[]K-W CG C0G 5.4 p ±0.25pF, ±0.5pF 508 200 0.125±0.013 R
TMK021 CG5R5[]K-W CG C0G 5.5 p ±0.25pF, ±0.5pF 510 200 0.125±0.013 R
TMK021 CG5R6[]K-W CG C0G 5.6 p ±0.25pF, ±0.5pF 512 200 0.125±0.013 R
TMK021 CG5R7[]K-W CG C0G 5.7 p ±0.25pF, ±0.5pF 514 200 0.125±0.013 R
TMK021 CG5R8[]K-W CG C0G 5.8 p ±0.25pF, ±0.5pF 516 200 0.125±0.013 R
TMK021 CG5R9[]K-W CG C0G 5.9 p ±0.25pF, ±0.5pF 518 200 0.125±0.013 R
TMK021 CG060[]K-W CG C0G 6 p ±0.25pF, ±0.5pF 520 200 0.125±0.013 R
TMK021 CG6R1[]K-W CG C0G 6.1 p ±0.25pF, ±0.5pF 522 200 0.125±0.013 R
TMK021 CG6R2[]K-W CG C0G 6.2 p ±0.25pF, ±0.5pF 524 200 0.125±0.013 R
TMK021 CG6R3[]K-W CG C0G 6.3 p ±0.25pF, ±0.5pF 526 200 0.125±0.013 R
TMK021 CG6R4[]K-W CG C0G 6.4 p ±0.25pF, ±0.5pF 528 200 0.125±0.013 R
TMK021 CG6R5[]K-W CG C0G 6.5 p ±0.25pF, ±0.5pF 530 200 0.125±0.013 R
TMK021 CG6R6[]K-W CG C0G 6.6 p ±0.25pF, ±0.5pF 532 200 0.125±0.013 R
TMK021 CG6R7[]K-W CG C0G 6.7 p ±0.25pF, ±0.5pF 534 200 0.125±0.013 R
TMK021 CG6R8[]K-W CG C0G 6.8 p ±0.25pF, ±0.5pF 536 200 0.125±0.013 R
TMK021 CG6R9[]K-W CG C0G 6.9 p ±0.25pF, ±0.5pF 538 200 0.125±0.013 R
TMK021 CG070[]K-W CG C0G 7 p ±0.25pF, ±0.5pF 540 200 0.125±0.013 R
TMK021 CG7R1[]K-W CG C0G 7.1 p ±0.25pF, ±0.5pF 542 200 0.125±0.013 R
TMK021 CG7R2[]K-W CG C0G 7.2 p ±0.25pF, ±0.5pF 544 200 0.125±0.013 R
TMK021 CG7R3[]K-W CG C0G 7.3 p ±0.25pF, ±0.5pF 546 200 0.125±0.013 R
TMK021 CG7R4[]K-W CG C0G 7.4 p ±0.25pF, ±0.5pF 548 200 0.125±0.013 R
TMK021 CG7R5[]K-W CG C0G 7.5 p ±0.25pF, ±0.5pF 550 200 0.125±0.013 R
TMK021 CG7R6[]K-W CG C0G 7.6 p ±0.25pF, ±0.5pF 552 200 0.125±0.013 R
TMK021 CG7R7[]K-W CG C0G 7.7 p ±0.25pF, ±0.5pF 554 200 0.125±0.013 R
TMK021 CG7R8[]K-W CG C0G 7.8 p ±0.25pF, ±0.5pF 556 200 0.125±0.013 R
TMK021 CG7R9[]K-W CG C0G 7.9 p ±0.25pF, ±0.5pF 558 200 0.125±0.013 R
TMK021 CG080[]K-W CG C0G 8 p ±0.25pF, ±0.5pF 560 200 0.125±0.013 R
TMK021 CG8R1[]K-W CG C0G 8.1 p ±0.25pF, ±0.5pF 562 200 0.125±0.013 R
TMK021 CG8R2[]K-W CG C0G 8.2 p ±0.25pF, ±0.5pF 564 200 0.125±0.013 R
TMK021 CG8R3[]K-W CG C0G 8.3 p ±0.25pF, ±0.5pF 566 200 0.125±0.013 R
TMK021 CG8R4[]K-W CG C0G 8.4 p ±0.25pF, ±0.5pF 568 200 0.125±0.013 R
TMK021 CG8R5[]K-W CG C0G 8.5 p ±0.25pF, ±0.5pF 570 200 0.125±0.013 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1MHz)
min
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
25
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
25
1
8
■PARTS NUMBER
HTLT
Rated voltage x ％
TMK021 CG8R6[]K-W CG C0G 8.6 p ±0.25pF, ±0.5pF 572 200 0.125±0.013 R
TMK021 CG8R7[]K-W CG C0G 8.7 p ±0.25pF, ±0.5pF 574 200 0.125±0.013 R
TMK021 CG8R8[]K-W CG C0G 8.8 p ±0.25pF, ±0.5pF 576 200 0.125±0.013 R
TMK021 CG8R9[]K-W CG C0G 8.9 p ±0.25pF, ±0.5pF 578 200 0.125±0.013 R
TMK021 CG090[]K-W CG C0G 9 p ±0.25pF, ±0.5pF 580 200 0.125±0.013 R
TMK021 CG9R1[]K-W CG C0G 9.1 p ±0.25pF, ±0.5pF 582 200 0.125±0.013 R
TMK021 CG9R2[]K-W CG C0G 9.2 p ±0.25pF, ±0.5pF 584 200 0.125±0.013 R
TMK021 CG9R3[]K-W CG C0G 9.3 p ±0.25pF, ±0.5pF 586 200 0.125±0.013 R
TMK021 CG9R4[]K-W CG C0G 9.4 p ±0.25pF, ±0.5pF 588 200 0.125±0.013 R
TMK021 CG9R5[]K-W CG C0G 9.5 p ±0.25pF, ±0.5pF 590 200 0.125±0.013 R
TMK021 CG9R6[]K-W CG C0G 9.6 p ±0.25pF, ±0.5pF 592 200 0.125±0.013 R
TMK021 CG9R7[]K-W CG C0G 9.7 p ±0.25pF, ±0.5pF 594 200 0.125±0.013 R
TMK021 CG9R8[]K-W CG C0G 9.8 p ±0.25pF, ±0.5pF 596 200 0.125±0.013 R
TMK021 CG9R9[]K-W CG C0G 9.9 p ±0.25pF, ±0.5pF 598 200 0.125±0.013 R
TMK021 CG100DK-W CG C0G 10 p ±0.5pF 600 200 0.125±0.013 R
TMK021 CG120JK-W CG C0G 12 p ±5％ 640 200 0.125±0.013 R
TMK021 CG150JK-W CG C0G 15 p ±5％ 700 200 0.125±0.013 R
TMK021 CG180JK-W CG C0G 18 p ±5％ 760 200 0.125±0.013 R
TMK021 CG220JK-W CG C0G 22 p ±5％ 840 200 0.125±0.013 R
TMK021 CG270JK-W CG C0G 27 p ±5％ 940 200 0.125±0.013 R
EMK021 CG330JK-W CG C0G 33 p ±5％ 1000 150 0.125±0.013 R
EMK021 CG390JK-W CG C0G 39 p ±5％ 1000 150 0.125±0.013 R
EMK021 CG470JK-W CG C0G 47 p ±5％ 1000 150 0.125±0.013 R
EMK021 CG560JK-W CG C0G 56 p ±5％ 1000 150 0.125±0.013 R
●042TYPE
【Temperature Characteristic CG : CG/C0G】　0.2mm thickness（C,D）
HTLT
Rated voltage x ％
TMK042 CG0R4[]D-W CG C0G 0.4 p ±0.05pF, ±0.1pF, ±0.25pF 408 200 0.2±0.0
2R
TMK042 CG0R5[]D-W CG C0G 0.5 p ±0.05pF, ±0.1pF, ±0.25pF 410 200 0.2±0.0
2R
TMK042 CG0R6[]D-W CG C0G 0.6 p ±0.05pF, ±0.1pF, ±0.25pF 412 200 0.2±0.0
2R
TMK042 CG0R7[]D-W CG C0G 0.7 p ±0.05pF, ±0.1pF, ±0.25pF 414 200 0.2±0.0
2R
TMK042 CGR75[]D-W CG C0G 0.75 p ±0.05pF, ±0.1pF, ±0.25pF 415 200 0.2±0.02 R
TMK042 CG0R8[]D-W CG C0G 0.8 p ±0.05pF, ±0.1pF, ±0.25pF 416 200 0.2±0.0
2R
TMK042 CG0R9[]D-W CG C0G 0.9 p ±0.05pF, ±0.1pF, ±0.25pF 418 200 0.2±0.0
2R
TMK042 CG010[]D-W CG C0G 1 p ±0.05pF, ±0.1pF, ±0.25pF 420 200 0.2±0.02 R
TMK042 CG1R1[]D-W CG C0G 1.1 p ±0.05pF, ±0.1pF, ±0.25pF 422 200 0.2±0.0
2R
TMK042 CG1R2[]D-W CG C0G 1.2 p ±0.05pF, ±0.1pF, ±0.25pF 424 200 0.2±0.0
2R
TMK042 CG1R3[]D-W CG C0G 1.3 p ±0.05pF, ±0.1pF, ±0.25pF 426 200 0.2±0.0
2R
TMK042 CG1R4[]D-W CG C0G 1.4 p ±0.05pF, ±0.1pF, ±0.25pF 428 200 0.2±0.0
2R
TMK042 CG1R5[]D-W CG C0G 1.5 p ±0.05pF, ±0.1pF, ±0.25pF 430 200 0.2±0.0
2R
TMK042 CG1R6[]D-W CG C0G 1.6 p ±0.05pF, ±0.1pF, ±0.25pF 432 200 0.2±0.0
2R
TMK042 CG1R7[]D-W CG C0G 1.7 p ±0.05pF, ±0.1pF, ±0.25pF 434 200 0.2±0.0
2R
TMK042 CG1R8[]D-W CG C0G 1.8 p ±0.05pF, ±0.1pF, ±0.25pF 436 200 0.2±0.0
2R
TMK042 CG1R9[]D-W CG C0G 1.9 p ±0.05pF, ±0.1pF, ±0.25pF 438 200 0.2±0.0
2R
TMK042 CG020[]D-W CG C0G 2 p ±0.05pF, ±0.1pF, ±0.25pF 440 200 0.2±0.02 R
TMK042 CG2R1[]D-W CG C0G 2.1 p ±0.05pF, ±0.1pF, ±0.25pF 442 200 0.2±0.0
2R
TMK042 CG2R2[]D-W CG C0G 2.2 p ±0.05pF, ±0.1pF, ±0.25pF 444 200 0.2±0.0
2R
TMK042 CG2R3[]D-W CG C0G 2.3 p ±0.05pF, ±0.1pF, ±0.25pF 446 200 0.2±0.0
2R
TMK042 CG2R4[]D-W CG C0G 2.4 p ±0.05pF, ±0.1pF, ±0.25pF 448 200 0.2±0.0
2R
TMK042 CG2R5[]D-W CG C0G 2.5 p ±0.05pF, ±0.1pF, ±0.25pF 450 200 0.2±0.0
2R
TMK042 CG2R6[]D-W CG C0G 2.6 p ±0.05pF, ±0.1pF, ±0.25pF 452 200 0.2±0.0
2R
TMK042 CG2R7[]D-W CG C0G 2.7 p ±0.05pF, ±0.1pF, ±0.25pF 454 200 0.2±0.0
2R
TMK042 CG2R8[]D-W CG C0G 2.8 p ±0.05pF, ±0.1pF, ±0.25pF 456 200 0.2±0.0
2R
TMK042 CG2R9[]D-W CG C0G 2.9 p ±0.05pF, ±0.1pF, ±0.25pF 458 200 0.2±0.0
2R
TMK042 CG030[]D-W CG C0G 3 p ±0.05pF, ±0.1pF, ±0.25pF 460 200 0.2±0.02 R
TMK042 CG3R1[]D-W CG C0G 3.1 p ±0.1pF, ±0.25pF 462 200 0.2±0.02 R
TMK042 CG3R2[]D-W CG C0G 3.2 p ±0.1pF, ±0.25pF 464 200 0.2±0.02 R
TMK042 CG3R3[]D-W CG C0G 3.3 p ±0.1pF, ±0.25pF 466 200 0.2±0.02 R
TMK042 CG3R4[]D-W CG C0G 3.4 p ±0.1pF, ±0.25pF 468 200 0.2±0.02 R
TMK042 CG3R5[]D-W CG C0G 3.5 p ±0.1pF, ±0.25pF 470 200 0.2±0.02 R
TMK042 CG3R6[]D-W CG C0G 3.6 p ±0.1pF, ±0.25pF 472 200 0.2±0.02 R
TMK042 CG3R7[]D-W CG C0G 3.7 p ±0.1pF, ±0.25pF 474 200 0.2±0.02 R
TMK042 CG3R8[]D-W CG C0G 3.8 p ±0.1pF, ±0.25pF 476 200 0.2±0.02 R
TMK042 CG3R9[]D-W CG C0G 3.9 p ±0.1pF, ±0.25pF 478 200 0.2±0.02 R
TMK042 CG040[]D-W CG C0G 4 p ±0.1pF, ±0.25pF 480 200 0.2±0.02 R
TMK042 CG4R1[]D-W CG C0G 4.1 p ±0.1pF, ±0.25pF 482 200 0.2±0.02 R
TMK042 CG4R2[]D-W CG C0G 4.2 p ±0.1pF, ±0.25pF 484 200 0.2±0.02 R
TMK042 CG4R3[]D-W CG C0G 4.3 p ±0.1pF, ±0.25pF 486 200 0.2±0.02 R
TMK042 CG4R4[]D-W CG C0G 4.4 p ±0.1pF, ±0.25pF 488 200 0.2±0.02 R
TMK042 CG4R5[]D-W CG C0G 4.5 p ±0.1pF, ±0.25pF 490 200 0.2±0.02 R
TMK042 CG4R6[]D-W CG C0G 4.6 p ±0.1pF, ±0.25pF 492 200 0.2±0.02 R
TMK042 CG4R7[]D-W CG C0G 4.7 p ±0.1pF, ±0.25pF 494 200 0.2±0.02 R
TMK042 CG4R8[]D-W CG C0G 4.8 p ±0.1pF, ±0.25pF 496 200 0.2±0.02 R
TMK042 CG4R9[]D-W CG C0G 4.9 p ±0.1pF, ±0.25pF 498 200 0.2±0.02 R
TMK042 CG050[]D-W CG C0G 5 p ±0.1pF, ±0.25pF 500 200 0.2±0.02 R
TMK042 CG5R1[]D-W CG C0G 5.1 p ±0.1pF, ±0.25pF, ±0.5pF 502 200 0.2±0.02 R
TMK042 CG5R2[]D-W CG C0G 5.2 p ±0.1pF, ±0.25pF, ±0.5pF 504 200 0.2±0.02 R
TMK042 CG5R3[]D-W CG C0G 5.3 p ±0.1pF, ±0.25pF, ±0.5pF 506 200 0.2±0.02 R
TMK042 CG5R4[]D-W CG C0G 5.4 p ±0.1pF, ±0.25pF, ±0.5pF 508 200 0.2±0.02 R
TMK042 CG5R5[]D-W CG C0G 5.5 p ±0.1pF, ±0.25pF, ±0.5pF 510 200 0.2±0.02 R
TMK042 CG5R6[]D-W CG C0G 5.6 p ±0.1pF, ±0.25pF, ±0.5pF 512 200 0.2±0.02 R
TMK042 CG5R7[]D-W CG C0G 5.7 p ±0.1pF, ±0.25pF, ±0.5pF 514 200 0.2±0.02 R
TMK042 CG5R8[]D-W CG C0G 5.8 p ±0.1pF, ±0.25pF, ±0.5pF 516 200 0.2±0.02 R
TMK042 CG5R9[]D-W CG C0G 5.9 p ±0.1pF, ±0.25pF, ±0.5pF 518 200 0.2±0.02 R
TMK042 CG060[]D-W CG C0G 6 p ±0.1pF, ±0.25pF, ±0.5pF 520 200 0.2±0.02 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1MHz)
min
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
25
16
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1MHz)
min
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
25
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
26
1
8
■PARTS NUMBER
HTLT
Rated voltage x ％
TMK042 CG6R1[]D-W CG C0G 6.1 p ±0.1pF, ±0.25pF, ±0.5pF 522 200 0.2±0.02 R
TMK042 CG6R2[]D-W CG C0G 6.2 p ±0.1pF, ±0.25pF, ±0.5pF 524 200 0.2±0.02 R
TMK042 CG6R3[]D-W CG C0G 6.3 p ±0.1pF, ±0.25pF, ±0.5pF 526 200 0.2±0.02 R
TMK042 CG6R4[]D-W CG C0G 6.4 p ±0.1pF, ±0.25pF, ±0.5pF 528 200 0.2±0.02 R
TMK042 CG6R5[]D-W CG C0G 6.5 p ±0.1pF, ±0.25pF, ±0.5pF 530 200 0.2±0.02 R
TMK042 CG6R6[]D-W CG C0G 6.6 p ±0.1pF, ±0.25pF, ±0.5pF 532 200 0.2±0.02 R
TMK042 CG6R7[]D-W CG C0G 6.7 p ±0.1pF, ±0.25pF, ±0.5pF 534 200 0.2±0.02 R
TMK042 CG6R8[]D-W CG C0G 6.8 p ±0.1pF, ±0.25pF, ±0.5pF 536 200 0.2±0.02 R
TMK042 CG6R9[]D-W CG C0G 6.9 p ±0.1pF, ±0.25pF, ±0.5pF 538 200 0.2±0.02 R
TMK042 CG070[]D-W CG C0G 7 p ±0.1pF, ±0.25pF, ±0.5pF 540 200 0.2±0.02 R
TMK042 CG7R1[]D-W CG C0G 7.1 p ±0.1pF, ±0.25pF, ±0.5pF 542 200 0.2±0.02 R
TMK042 CG7R2[]D-W CG C0G 7.2 p ±0.1pF, ±0.25pF, ±0.5pF 544 200 0.2±0.02 R
TMK042 CG7R3[]D-W CG C0G 7.3 p ±0.1pF, ±0.25pF, ±0.5pF 546 200 0.2±0.02 R
TMK042 CG7R4[]D-W CG C0G 7.4 p ±0.1pF, ±0.25pF, ±0.5pF 548 200 0.2±0.02 R
TMK042 CG7R5[]D-W CG C0G 7.5 p ±0.1pF, ±0.25pF, ±0.5pF 550 200 0.2±0.02 R
TMK042 CG7R6[]D-W CG C0G 7.6 p ±0.1pF, ±0.25pF, ±0.5pF 552 200 0.2±0.02 R
TMK042 CG7R7[]D-W CG C0G 7.7 p ±0.1pF, ±0.25pF, ±0.5pF 554 200 0.2±0.02 R
TMK042 CG7R8[]D-W CG C0G 7.8 p ±0.1pF, ±0.25pF, ±0.5pF 556 200 0.2±0.02 R
TMK042 CG7R9[]D-W CG C0G 7.9 p ±0.1pF, ±0.25pF, ±0.5pF 558 200 0.2±0.02 R
TMK042 CG080[]D-W CG C0G 8 p ±0.1pF, ±0.25pF, ±0.5pF 560 200 0.2±0.02 R
TMK042 CG8R1[]D-W CG C0G 8.1 p ±0.1pF, ±0.25pF, ±0.5pF 562 200 0.2±0.02 R
TMK042 CG8R2[]D-W CG C0G 8.2 p ±0.1pF, ±0.25pF, ±0.5pF 564 200 0.2±0.02 R
TMK042 CG8R3[]D-W CG C0G 8.3 p ±0.1pF, ±0.25pF, ±0.5pF 566 200 0.2±0.02 R
TMK042 CG8R4[]D-W CG C0G 8.4 p ±0.1pF, ±0.25pF, ±0.5pF 568 200 0.2±0.02 R
TMK042 CG8R5[]D-W CG C0G 8.5 p ±0.1pF, ±0.25pF, ±0.5pF 570 200 0.2±0.02 R
TMK042 CG8R6[]D-W CG C0G 8.6 p ±0.1pF, ±0.25pF, ±0.5pF 572 200 0.2±0.02 R
TMK042 CG8R7[]D-W CG C0G 8.7 p ±0.1pF, ±0.25pF, ±0.5pF 574 200 0.2±0.02 R
TMK042 CG8R8[]D-W CG C0G 8.8 p ±0.1pF, ±0.25pF, ±0.5pF 576 200 0.2±0.02 R
TMK042 CG8R9[]D-W CG C0G 8.9 p ±0.1pF, ±0.25pF, ±0.5pF 578 200 0.2±0.02 R
TMK042 CG090[]D-W CG C0G 9 p ±0.1pF, ±0.25pF, ±0.5pF 580 200 0.2±0.02 R
TMK042 CG9R1[]D-W CG C0G 9.1 p ±0.1pF, ±0.25pF, ±0.5pF 582 200 0.2±0.02 R
TMK042 CG9R2[]D-W CG C0G 9.2 p ±0.1pF, ±0.25pF, ±0.5pF 584 200 0.2±0.02 R
TMK042 CG9R3[]D-W CG C0G 9.3 p ±0.1pF, ±0.25pF, ±0.5pF 586 200 0.2±0.02 R
TMK042 CG9R4[]D-W CG C0G 9.4 p ±0.1pF, ±0.25pF, ±0.5pF 588 200 0.2±0.02 R
TMK042 CG9R5[]D-W CG C0G 9.5 p ±0.1pF, ±0.25pF, ±0.5pF 590 200 0.2±0.02 R
TMK042 CG9R6[]D-W CG C0G 9.6 p ±0.1pF, ±0.25pF, ±0.5pF 592 200 0.2±0.02 R
TMK042 CG9R7[]D-W CG C0G 9.7 p ±0.1pF, ±0.25pF, ±0.5pF 594 200 0.2±0.02 R
TMK042 CG9R8[]D-W CG C0G 9.8 p ±0.1pF, ±0.25pF, ±0.5pF 596 200 0.2±0.02 R
TMK042 CG9R9[]D-W CG C0G 9.9 p ±0.1pF, ±0.25pF, ±0.5pF 598 200 0.2±0.02 R
TMK042 CG100DD-W CG C0G 10 p ±0.5pF 600 200 0.2±0.02 R
TMK042 CG110JD-W CG C0G 11 p ±5％ 620 200 0.2±0.02 R
TMK042 CG120JD-W CG C0G 12 p ±5％ 640 200 0.2±0.02 R
TMK042 CG130JD-W CG C0G 13 p ±5％ 660 200 0.2±0.02 R
TMK042 CG150JD-W CG C0G 15 p ±5％ 700 200 0.2±0.02 R
TMK042 CG160JC-W CG C0G 16 p ±5％ 720 200 0.2±0.02 R
TMK042 CG180JC-W CG C0G 18 p ±5％ 760 200 0.2±0.02 R
TMK042 CG200JC-W CG C0G 20 p ±5％ 800 200 0.2±0.02 R
TMK042 CG220JC-W CG C0G 22 p ±5％ 840 200 0.2±0.02 R
TMK042 CG240JC-W CG C0G 24 p ±5％ 880 200 0.2±0.02 R
TMK042 CG270JC-W CG C0G 27 p ±5％ 940 200 0.2±0.02 R
TMK042 CG300JC-W CG C0G 30 p ±5％ 1000 200 0.2±0.02 R
TMK042 CG330JC-W CG C0G 33 p ±5％ 1000 200 0.2±0.02 R
TMK042 CG360JC-W CG C0G 36 p ±5％ 1000 200 0.2±0.02 R
TMK042 CG390JC-W CG C0G 39 p ±5％ 1000 200 0.2±0.02 R
TMK042 CG430JC-W CG C0G 43 p ±5％ 1000 200 0.2±0.02 R
TMK042 CG470JC-W CG C0G 47 p ±5％ 1000 200 0.2±0.02 R
TMK042 CG510JC-W CG C0G 51 p ±5％ 1000 200 0.2±0.02 R
TMK042 CG560JC-W CG C0G 56 p ±5％ 1000 200 0.2±0.02 R
TMK042 CG620JC-W CG C0G 62 p ±5％ 1000 200 0.2±0.02 R
TMK042 CG680JC-W CG C0G 68 p ±5％ 1000 200 0.2±0.02 R
TMK042 CG750JC-W CG C0G 75 p ±5％ 1000 200 0.2±0.02 R
TMK042 CG820JC-W CG C0G 82 p ±5％ 1000 200 0.2±0.02 R
TMK042 CG910JC-W CG C0G 91 p ±5％ 1000 200 0.2±0.02 R
TMK042 CG101JC-W CG C0G 100 p ±5％ 1000 200 0.2±0.02 R
【Temperature Characteristic CG : CG/C0G】　0.2mm thickness（C,D）
HTLT
Rated voltage x ％
EMK042 CG0R4[]D-W CG C0G 0.4 p ±0.05pF, ±0.1pF, ±0.25pF 408 200 0.2±0.0
2R
EMK042 CG0R5[]D-W CG C0G 0.5 p ±0.05pF, ±0.1pF, ±0.25pF 410 200 0.2±0.0
2R
EMK042 CG0R6[]D-W CG C0G 0.6 p ±0.05pF, ±0.1pF, ±0.25pF 412 200 0.2±0.0
2R
EMK042 CG0R7[]D-W CG C0G 0.7 p ±0.05pF, ±0.1pF, ±0.25pF 414 200 0.2±0.0
2R
EMK042 CGR75[]D-W CG C0G 0.75 p ±0.05pF, ±0.1pF, ±0.25pF 415 200 0.2±0.02 R
EMK042 CG0R8[]D-W CG C0G 0.8 p ±0.05pF, ±0.1pF, ±0.25pF 416 200 0.2±0.0
2R
EMK042 CG0R9[]D-W CG C0G 0.9 p ±0.05pF, ±0.1pF, ±0.25pF 418 200 0.2±0.0
2R
EMK042 CG010[]D-W CG C0G 1 p ±0.05pF, ±0.1pF, ±0.25pF 420 200 0.2±0.02 R
EMK042 CG1R1[]D-W CG C0G 1.1 p ±0.05pF, ±0.1pF, ±0.25pF 422 200 0.2±0.0
2R
EMK042 CG1R2[]D-W CG C0G 1.2 p ±0.05pF, ±0.1pF, ±0.25pF 424 200 0.2±0.0
2R
EMK042 CG1R3[]D-W CG C0G 1.3 p ±0.05pF, ±0.1pF, ±0.25pF 426 200 0.2±0.0
2R
EMK042 CG1R4[]D-W CG C0G 1.4 p ±0.05pF, ±0.1pF, ±0.25pF 428 200 0.2±0.0
2R
EMK042 CG1R5[]D-W CG C0G 1.5 p ±0.05pF, ±0.1pF, ±0.25pF 430 200 0.2±0.0
2R
EMK042 CG1R6[]D-W CG C0G 1.6 p ±0.05pF, ±0.1pF, ±0.25pF 432 200 0.2±0.0
2R
EMK042 CG1R7[]D-W CG C0G 1.7 p ±0.05pF, ±0.1pF, ±0.25pF 434 200 0.2±0.0
2R
EMK042 CG1R8[]D-W CG C0G 1.8 p ±0.05pF, ±0.1pF, ±0.25pF 436 200 0.2±0.0
2R
EMK042 CG1R9[]D-W CG C0G 1.9 p ±0.05pF, ±0.1pF, ±0.25pF 438 200 0.2±0.0
2R
EMK042 CG020[]D-W CG C0G 2 p ±0.05pF, ±0.1pF, ±0.25pF 440 200 0.2±0.02 R
EMK042 CG2R1[]D-W CG C0G 2.1 p ±0.05pF, ±0.1pF, ±0.25pF 442 200 0.2±0.0
2R
EMK042 CG2R2[]D-W CG C0G 2.2 p ±0.05pF, ±0.1pF, ±0.25pF 444 200 0.2±0.0
2R
EMK042 CG2R3[]D-W CG C0G 2.3 p ±0.05pF, ±0.1pF, ±0.25pF 446 200 0.2±0.0
2R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1MHz)
min
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
25
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1MHz)
min
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
16
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
27
1
8
■PARTS NUMBER
HTLT
Rated voltage x ％
EMK042 CG2R4[]D-W CG C0G 2.4 p ±0.05pF, ±0.1pF, ±0.25pF 448 200 0.2±0.0
2R
EMK042 CG2R5[]D-W CG C0G 2.5 p ±0.05pF, ±0.1pF, ±0.25pF 450 200 0.2±0.0
2R
EMK042 CG2R6[]D-W CG C0G 2.6 p ±0.05pF, ±0.1pF, ±0.25pF 452 200 0.2±0.0
2R
EMK042 CG2R7[]D-W CG C0G 2.7 p ±0.05pF, ±0.1pF, ±0.25pF 454 200 0.2±0.0
2R
EMK042 CG2R8[]D-W CG C0G 2.8 p ±0.05pF, ±0.1pF, ±0.25pF 456 200 0.2±0.0
2R
EMK042 CG2R9[]D-W CG C0G 2.9 p ±0.05pF, ±0.1pF, ±0.25pF 458 200 0.2±0.0
2R
EMK042 CG030[]D-W CG C0G 3 p ±0.05pF, ±0.1pF, ±0.25pF 460 200 0.2±0.02 R
EMK042 CG3R1[]D-W CG C0G 3.1 p ±0.1pF, ±0.25pF 462 200 0.2±0.02 R
EMK042 CG3R2[]D-W CG C0G 3.2 p ±0.1pF, ±0.25pF 464 200 0.2±0.02 R
EMK042 CG3R3[]D-W CG C0G 3.3 p ±0.1pF, ±0.25pF 466 200 0.2±0.02 R
EMK042 CG3R4[]D-W CG C0G 3.4 p ±0.1pF, ±0.25pF 468 200 0.2±0.02 R
EMK042 CG3R5[]D-W CG C0G 3.5 p ±0.1pF, ±0.25pF 470 200 0.2±0.02 R
EMK042 CG3R6[]D-W CG C0G 3.6 p ±0.1pF, ±0.25pF 472 200 0.2±0.02 R
EMK042 CG3R7[]D-W CG C0G 3.7 p ±0.1pF, ±0.25pF 474 200 0.2±0.02 R
EMK042 CG3R8[]D-W CG C0G 3.8 p ±0.1pF, ±0.25pF 476 200 0.2±0.02 R
EMK042 CG3R9[]D-W CG C0G 3.9 p ±0.1pF, ±0.25pF 478 200 0.2±0.02 R
EMK042 CG040[]D-W CG C0G 4 p ±0.1pF, ±0.25pF 480 200 0.2±0.02 R
EMK042 CG4R1[]D-W CG C0G 4.1 p ±0.1pF, ±0.25pF 482 200 0.2±0.02 R
EMK042 CG4R2[]D-W CG C0G 4.2 p ±0.1pF, ±0.25pF 484 200 0.2±0.02 R
EMK042 CG4R3[]D-W CG C0G 4.3 p ±0.1pF, ±0.25pF 486 200 0.2±0.02 R
EMK042 CG4R4[]D-W CG C0G 4.4 p ±0.1pF, ±0.25pF 488 200 0.2±0.02 R
EMK042 CG4R5[]D-W CG C0G 4.5 p ±0.1pF, ±0.25pF 490 200 0.2±0.02 R
EMK042 CG4R6[]D-W CG C0G 4.6 p ±0.1pF, ±0.25pF 492 200 0.2±0.02 R
EMK042 CG4R7[]D-W CG C0G 4.7 p ±0.1pF, ±0.25pF 494 200 0.2±0.02 R
EMK042 CG4R8[]D-W CG C0G 4.8 p ±0.1pF, ±0.25pF 496 200 0.2±0.02 R
EMK042 CG4R9[]D-W CG C0G 4.9 p ±0.1pF, ±0.25pF 498 200 0.2±0.02 R
EMK042 CG050[]D-W CG C0G 5 p ±0.1pF, ±0.25pF 500 200 0.2±0.02 R
EMK042 CG5R1[]D-W CG C0G 5.1 p ±0.1pF, ±0.25pF, ±0.5pF 502 200 0.2±0.02 R
EMK042 CG5R2[]D-W CG C0G 5.2 p ±0.1pF, ±0.25pF, ±0.5pF 504 200 0.2±0.02 R
EMK042 CG5R3[]D-W CG C0G 5.3 p ±0.1pF, ±0.25pF, ±0.5pF 506 200 0.2±0.02 R
EMK042 CG5R4[]D-W CG C0G 5.4 p ±0.1pF, ±0.25pF, ±0.5pF 508 200 0.2±0.02 R
EMK042 CG5R5[]D-W CG C0G 5.5 p ±0.1pF, ±0.25pF, ±0.5pF 510 200 0.2±0.02 R
EMK042 CG5R6[]D-W CG C0G 5.6 p ±0.1pF, ±0.25pF, ±0.5pF 512 200 0.2±0.02 R
EMK042 CG5R7[]D-W CG C0G 5.7 p ±0.1pF, ±0.25pF, ±0.5pF 514 200 0.2±0.02 R
EMK042 CG5R8[]D-W CG C0G 5.8 p ±0.1pF, ±0.25pF, ±0.5pF 516 200 0.2±0.02 R
EMK042 CG5R9[]D-W CG C0G 5.9 p ±0.1pF, ±0.25pF, ±0.5pF 518 200 0.2±0.02 R
EMK042 CG060[]D-W CG C0G 6 p ±0.1pF, ±0.25pF, ±0.5pF 520 200 0.2±0.02 R
EMK042 CG6R1[]D-W CG C0G 6.1 p ±0.1pF, ±0.25pF, ±0.5pF 522 200 0.2±0.02 R
EMK042 CG6R2[]D-W CG C0G 6.2 p ±0.1pF, ±0.25pF, ±0.5pF 524 200 0.2±0.02 R
EMK042 CG6R3[]D-W CG C0G 6.3 p ±0.1pF, ±0.25pF, ±0.5pF 526 200 0.2±0.02 R
EMK042 CG6R4[]D-W CG C0G 6.4 p ±0.1pF, ±0.25pF, ±0.5pF 528 200 0.2±0.02 R
EMK042 CG6R5[]D-W CG C0G 6.5 p ±0.1pF, ±0.25pF, ±0.5pF 530 200 0.2±0.02 R
EMK042 CG6R6[]D-W CG C0G 6.6 p ±0.1pF, ±0.25pF, ±0.5pF 532 200 0.2±0.02 R
EMK042 CG6R7[]D-W CG C0G 6.7 p ±0.1pF, ±0.25pF, ±0.5pF 534 200 0.2±0.02 R
EMK042 CG6R8[]D-W CG C0G 6.8 p ±0.1pF, ±0.25pF, ±0.5pF 536 200 0.2±0.02 R
EMK042 CG6R9[]D-W CG C0G 6.9 p ±0.1pF, ±0.25pF, ±0.5pF 538 200 0.2±0.02 R
EMK042 CG070[]D-W CG C0G 7 p ±0.1pF, ±0.25pF, ±0.5pF 540 200 0.2±0.02 R
EMK042 CG7R1[]D-W CG C0G 7.1 p ±0.1pF, ±0.25pF, ±0.5pF 542 200 0.2±0.02 R
EMK042 CG7R2[]D-W CG C0G 7.2 p ±0.1pF, ±0.25pF, ±0.5pF 544 200 0.2±0.02 R
EMK042 CG7R3[]D-W CG C0G 7.3 p ±0.1pF, ±0.25pF, ±0.5pF 546 200 0.2±0.02 R
EMK042 CG7R4[]D-W CG C0G 7.4 p ±0.1pF, ±0.25pF, ±0.5pF 548 200 0.2±0.02 R
EMK042 CG7R5[]D-W CG C0G 7.5 p ±0.1pF, ±0.25pF, ±0.5pF 550 200 0.2±0.02 R
EMK042 CG7R6[]D-W CG C0G 7.6 p ±0.1pF, ±0.25pF, ±0.5pF 552 200 0.2±0.02 R
EMK042 CG7R7[]D-W CG C0G 7.7 p ±0.1pF, ±0.25pF, ±0.5pF 554 200 0.2±0.02 R
EMK042 CG7R8[]D-W CG C0G 7.8 p ±0.1pF, ±0.25pF, ±0.5pF 556 200 0.2±0.02 R
EMK042 CG7R9[]D-W CG C0G 7.9 p ±0.1pF, ±0.25pF, ±0.5pF 558 200 0.2±0.02 R
EMK042 CG080[]D-W CG C0G 8 p ±0.1pF, ±0.25pF, ±0.5pF 560 200 0.2±0.02 R
EMK042 CG8R1[]D-W CG C0G 8.1 p ±0.1pF, ±0.25pF, ±0.5pF 562 200 0.2±0.02 R
EMK042 CG8R2[]D-W CG C0G 8.2 p ±0.1pF, ±0.25pF, ±0.5pF 564 200 0.2±0.02 R
EMK042 CG8R3[]D-W CG C0G 8.3 p ±0.1pF, ±0.25pF, ±0.5pF 566 200 0.2±0.02 R
EMK042 CG8R4[]D-W CG C0G 8.4 p ±0.1pF, ±0.25pF, ±0.5pF 568 200 0.2±0.02 R
EMK042 CG8R5[]D-W CG C0G 8.5 p ±0.1pF, ±0.25pF, ±0.5pF 570 200 0.2±0.02 R
EMK042 CG8R6[]D-W CG C0G 8.6 p ±0.1pF, ±0.25pF, ±0.5pF 572 200 0.2±0.02 R
EMK042 CG8R7[]D-W CG C0G 8.7 p ±0.1pF, ±0.25pF, ±0.5pF 574 200 0.2±0.02 R
EMK042 CG8R8[]D-W CG C0G 8.8 p ±0.1pF, ±0.25pF, ±0.5pF 576 200 0.2±0.02 R
EMK042 CG8R9[]D-W CG C0G 8.9 p ±0.1pF, ±0.25pF, ±0.5pF 578 200 0.2±0.02 R
EMK042 CG090[]D-W CG C0G 9 p ±0.1pF, ±0.25pF, ±0.5pF 580 200 0.2±0.02 R
EMK042 CG9R1[]D-W CG C0G 9.1 p ±0.1pF, ±0.25pF, ±0.5pF 582 200 0.2±0.02 R
EMK042 CG9R2[]D-W CG C0G 9.2 p ±0.1pF, ±0.25pF, ±0.5pF 584 200 0.2±0.02 R
EMK042 CG9R3[]D-W CG C0G 9.3 p ±0.1pF, ±0.25pF, ±0.5pF 586 200 0.2±0.02 R
EMK042 CG9R4[]D-W CG C0G 9.4 p ±0.1pF, ±0.25pF, ±0.5pF 588 200 0.2±0.02 R
EMK042 CG9R5[]D-W CG C0G 9.5 p ±0.1pF, ±0.25pF, ±0.5pF 590 200 0.2±0.02 R
EMK042 CG9R6[]D-W CG C0G 9.6 p ±0.1pF, ±0.25pF, ±0.5pF 592 200 0.2±0.02 R
EMK042 CG9R7[]D-W CG C0G 9.7 p ±0.1pF, ±0.25pF, ±0.5pF 594 200 0.2±0.02 R
EMK042 CG9R8[]D-W CG C0G 9.8 p ±0.1pF, ±0.25pF, ±0.5pF 596 200 0.2±0.02 R
EMK042 CG9R9[]D-W CG C0G 9.9 p ±0.1pF, ±0.25pF, ±0.5pF 598 200 0.2±0.02 R
EMK042 CG100DD-W CG C0G 10 p ±0.5pF 600 200 0.2±0.02 R
EMK042 CG110JD-W CG C0G 11 p ±5％ 620 200 0.2±0.02 R
EMK042 CG120JD-W CG C0G 12 p ±5％ 640 200 0.2±0.02 R
EMK042 CG130JD-W CG C0G 13 p ±5％ 660 200 0.2±0.02 R
EMK042 CG150JD-W CG C0G 15 p ±5％ 700 200 0.2±0.02 R
EMK042 CG160JC-W CG C0G 16 p ±5％ 720 200 0.2±0.02 R
EMK042 CG180JC-W CG C0G 18 p ±5％ 760 200 0.2±0.02 R
EMK042 CG200JC-W CG C0G 20 p ±5％ 800 200 0.2±0.02 R
EMK042 CG220JC-W CG C0G 22 p ±5％ 840 200 0.2±0.02 R
EMK042 CG240JC-W CG C0G 24 p ±5％ 880 200 0.2±0.02 R
EMK042 CG270JC-W CG C0G 27 p ±5％ 940 200 0.2±0.02 R
EMK042 CG300JC-W CG C0G 30 p ±5％ 1000 200 0.2±0.02 R
EMK042 CG330JC-W CG C0G 33 p ±5％ 1000 200 0.2±0.02 R
EMK042 CG360JC-W CG C0G 36 p ±5％ 1000 200 0.2±0.02 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1MHz)
min
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
16
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
28
1
8
■PARTS NUMBER
HTLT
Rated voltage x ％
EMK042 CG390JC-W CG C0G 39 p ±5％ 1000 200 0.2±0.02 R
EMK042 CG430JC-W CG C0G 43 p ±5％ 1000 200 0.2±0.02 R
EMK042 CG470JC-W CG C0G 47 p ±5％ 1000 200 0.2±0.02 R
EMK042 CG510JC-W CG C0G 51 p ±5％ 1000 200 0.2±0.02 R
EMK042 CG560JC-W CG C0G 56 p ±5％ 1000 200 0.2±0.02 R
EMK042 CG620JC-W CG C0G 62 p ±5％ 1000 200 0.2±0.02 R
EMK042 CG680JC-W CG C0G 68 p ±5％ 1000 200 0.2±0.02 R
EMK042 CG750JC-W CG C0G 75 p ±5％ 1000 200 0.2±0.02 R
EMK042 CG820JC-W CG C0G 82 p ±5％ 1000 200 0.2±0.02 R
EMK042 CG910JC-W CG C0G 91 p ±5％ 1000 200 0.2±0.02 R
EMK042 CG101JC-W CG C0G 100 p ±5％ 1000 200 0.2±0.02 R
EMK042 CG221JC-W CG C0G 220 p ±5％ 1000 200 0.2±0.02 R
LMK042 CG221JC-W 10 CG C0G 220 p ±5％ 1000 200 0.2±0.02 R
●063TYPE
【Temperature Characteristic CG : CG/C0G】　0.3mm thickness（T）
HTLT
Rated voltage x ％
UMK063 CG0R2[]T-F CG C0G 0.2 p ±0.1pF, ±0.25pF 404 200 0.3±0.03 R
UMK063 CG0R3[]T-F CG C0G 0.3 p ±0.1pF, ±0.25pF 406 200 0.3±0.03 R
UMK063 CG0R4[]T-F CG C0G 0.4 p ±0.1pF, ±0.25pF 408 200 0.3±0.03 R
UMK063 CG0R5[]T-F CG C0G 0.5 p ±0.1pF, ±0.25pF 410 200 0.3±0.03 R
UMK063 CG0R6[]T-F CG C0G 0.6 p ±0.1pF, ±0.25pF 412 200 0.3±0.03 R
UMK063 CG0R7[]T-F CG C0G 0.7 p ±0.1pF, ±0.25pF 414 200 0.3±0.03 R
UMK063 CGR75[]T-F CG C0G 0.75 p ±0.1pF, ±0.25pF 415 200 0.3±0.03 R
UMK063 CG0R8[]T-F CG C0G 0.8 p ±0.1pF, ±0.25pF 416 200 0.3±0.03 R
UMK063 CG0R9[]T-F CG C0G 0.9 p ±0.1pF, ±0.25pF 418 200 0.3±0.03 R
UMK063 CG010[]T-F CG C0G 1 p ±0.1pF, ±0.25pF 420 200 0.3±0.03 R
UMK063 CG1R1[]T-F CG C0G 1.1 p ±0.1pF, ±0.25pF 422 200 0.3±0.03 R
UMK063 CG1R2[]T-F CG C0G 1.2 p ±0.1pF, ±0.25pF 424 200 0.3±0.03 R
UMK063 CG1R3[]T-F CG C0G 1.3 p ±0.1pF, ±0.25pF 426 200 0.3±0.03 R
UMK063 CG1R4[]T-F CG C0G 1.4 p ±0.1pF, ±0.25pF 428 200 0.3±0.03 R
UMK063 CG1R5[]T-F CG C0G 1.5 p ±0.1pF, ±0.25pF 430 200 0.3±0.03 R
UMK063 CG1R6[]T-F CG C0G 1.6 p ±0.1pF, ±0.25pF 432 200 0.3±0.03 R
UMK063 CG1R7[]T-F CG C0G 1.7 p ±0.1pF, ±0.25pF 434 200 0.3±0.03 R
UMK063 CG1R8[]T-F CG C0G 1.8 p ±0.1pF, ±0.25pF 436 200 0.3±0.03 R
UMK063 CG1R9[]T-F CG C0G 1.9 p ±0.1pF, ±0.25pF 438 200 0.3±0.03 R
UMK063 CG020[]T-F CG C0G 2 p ±0.1pF, ±0.25pF 440 200 0.3±0.03 R
UMK063 CG2R1[]T-F CG C0G 2.1 p ±0.1pF, ±0.25pF 442 200 0.3±0.03 R
UMK063 CG2R2[]T-F CG C0G 2.2 p ±0.1pF, ±0.25pF 444 200 0.3±0.03 R
UMK063 CG2R3[]T-F CG C0G 2.3 p ±0.1pF, ±0.25pF 446 200 0.3±0.03 R
UMK063 CG2R4[]T-F CG C0G 2.4 p ±0.1pF, ±0.25pF 448 200 0.3±0.03 R
UMK063 CG2R5[]T-F CG C0G 2.5 p ±0.1pF, ±0.25pF 450 200 0.3±0.03 R
UMK063 CG2R6[]T-F CG C0G 2.6 p ±0.1pF, ±0.25pF 452 200 0.3±0.03 R
UMK063 CG2R7[]T-F CG C0G 2.7 p ±0.1pF, ±0.25pF 454 200 0.3±0.03 R
UMK063 CG2R8[]T-F CG C0G 2.8 p ±0.1pF, ±0.25pF 456 200 0.3±0.03 R
UMK063 CG2R9[]T-F CG C0G 2.9 p ±0.1pF, ±0.25pF 458 200 0.3±0.03 R
UMK063 CG030[]T-F CG C0G 3 p ±0.1pF, ±0.25pF 460 200 0.3±0.03 R
UMK063 CG3R1[]T-F CG C0G 3.1 p ±0.1pF, ±0.25pF 462 200 0.3±0.03 R
UMK063 CG3R2[]T-F CG C0G 3.2 p ±0.1pF, ±0.25pF 464 200 0.3±0.03 R
UMK063 CG3R3[]T-F CG C0G 3.3 p ±0.1pF, ±0.25pF 466 200 0.3±0.03 R
UMK063 CG3R4[]T-F CG C0G 3.4 p ±0.1pF, ±0.25pF 468 200 0.3±0.03 R
UMK063 CG3R5[]T-F CG C0G 3.5 p ±0.1pF, ±0.25pF 470 200 0.3±0.03 R
UMK063 CG3R6[]T-F CG C0G 3.6 p ±0.1pF, ±0.25pF 472 200 0.3±0.03 R
UMK063 CG3R7[]T-F CG C0G 3.7 p ±0.1pF, ±0.25pF 474 200 0.3±0.03 R
UMK063 CG3R8[]T-F CG C0G 3.8 p ±0.1pF, ±0.25pF 476 200 0.3±0.03 R
UMK063 CG3R9[]T-F CG C0G 3.9 p ±0.1pF, ±0.25pF 478 200 0.3±0.03 R
UMK063 CG040[]T-F CG C0G 4 p ±0.1pF, ±0.25pF 480 200 0.3±0.03 R
UMK063 CG4R1[]T-F CG C0G 4.1 p ±0.1pF, ±0.25pF 482 200 0.3±0.03 R
UMK063 CG4R2[]T-F CG C0G 4.2 p ±0.1pF, ±0.25pF 484 200 0.3±0.03 R
UMK063 CG4R3[]T-F CG C0G 4.3 p ±0.1pF, ±0.25pF 486 200 0.3±0.03 R
UMK063 CG4R4[]T-F CG C0G 4.4 p ±0.1pF, ±0.25pF 488 200 0.3±0.03 R
UMK063 CG4R5[]T-F CG C0G 4.5 p ±0.1pF, ±0.25pF 490 200 0.3±0.03 R
UMK063 CG4R6[]T-F CG C0G 4.6 p ±0.1pF, ±0.25pF 492 200 0.3±0.03 R
UMK063 CG4R7[]T-F CG C0G 4.7 p ±0.1pF, ±0.25pF 494 200 0.3±0.03 R
UMK063 CG4R8[]T-F CG C0G 4.8 p ±0.1pF, ±0.25pF 496 200 0.3±0.03 R
UMK063 CG4R9[]T-F CG C0G 4.9 p ±0.1pF, ±0.25pF 498 200 0.3±0.03 R
UMK063 CG050[]T-F CG C0G 5 p ±0.1pF, ±0.25pF 500 200 0.3±0.03 R
UMK063 CG5R1[]T-F CG C0G 5.1 p ±0.1pF, ±0.25pF, ±0.5pF 502 200 0.3±0.03 R
UMK063 CG5R2[]T-F CG C0G 5.2 p ±0.1pF, ±0.25pF, ±0.5pF 504 200 0.3±0.03 R
UMK063 CG5R3[]T-F CG C0G 5.3 p ±0.1pF, ±0.25pF, ±0.5pF 506 200 0.3±0.03 R
UMK063 CG5R4[]T-F CG C0G 5.4 p ±0.1pF, ±0.25pF, ±0.5pF 508 200 0.3±0.03 R
UMK063 CG5R5[]T-F CG C0G 5.5 p ±0.1pF, ±0.25pF, ±0.5pF 510 200 0.3±0.03 R
UMK063 CG5R6[]T-F CG C0G 5.6 p ±0.1pF, ±0.25pF, ±0.5pF 512 200 0.3±0.03 R
UMK063 CG5R7[]T-F CG C0G 5.7 p ±0.1pF, ±0.25pF, ±0.5pF 514 200 0.3±0.03 R
UMK063 CG5R8[]T-F CG C0G 5.8 p ±0.1pF, ±0.25pF, ±0.5pF 516 200 0.3±0.03 R
UMK063 CG5R9[]T-F CG C0G 5.9 p ±0.1pF, ±0.25pF, ±0.5pF 518 200 0.3±0.03 R
UMK063 CG060[]T-F CG C0G 6 p ±0.1pF, ±0.25pF, ±0.5pF 520 200 0.3±0.03 R
UMK063 CG6R1[]T-F CG C0G 6.1 p ±0.1pF, ±0.25pF, ±0.5pF 522 200 0.3±0.03 R
UMK063 CG6R2[]T-F CG C0G 6.2 p ±0.1pF, ±0.25pF, ±0.5pF 524 200 0.3±0.03 R
UMK063 CG6R3[]T-F CG C0G 6.3 p ±0.1pF, ±0.25pF, ±0.5pF 526 200 0.3±0.03 R
UMK063 CG6R4[]T-F CG C0G 6.4 p ±0.1pF, ±0.25pF, ±0.5pF 528 200 0.3±0.03 R
UMK063 CG6R5[]T-F CG C0G 6.5 p ±0.1pF, ±0.25pF, ±0.5pF 530 200 0.3±0.03 R
UMK063 CG6R6[]T-F CG C0G 6.6 p ±0.1pF, ±0.25pF, ±0.5pF 532 200 0.3±0.03 R
UMK063 CG6R7[]T-F CG C0G 6.7 p ±0.1pF, ±0.25pF, ±0.5pF 534 200 0.3±0.03 R
UMK063 CG6R8[]T-F CG C0G 6.8 p ±0.1pF, ±0.25pF, ±0.5pF 536 200 0.3±0.03 R
UMK063 CG6R9[]T-F CG C0G 6.9 p ±0.1pF, ±0.25pF, ±0.5pF 538 200 0.3±0.03 R
50
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1MHz)
min
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
16
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1MHz)
min
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
29
1
8
■PARTS NUMBER
HTLT
Rated voltage x ％
UMK063 CG070[]T-F CG C0G 7 p ±0.1pF, ±0.25pF, ±0.5pF 540 200 0.3±0.03 R
UMK063 CG7R1[]T-F CG C0G 7.1 p ±0.1pF, ±0.25pF, ±0.5pF 542 200 0.3±0.03 R
UMK063 CG7R2[]T-F CG C0G 7.2 p ±0.1pF, ±0.25pF, ±0.5pF 544 200 0.3±0.03 R
UMK063 CG7R3[]T-F CG C0G 7.3 p ±0.1pF, ±0.25pF, ±0.5pF 546 200 0.3±0.03 R
UMK063 CG7R4[]T-F CG C0G 7.4 p ±0.1pF, ±0.25pF, ±0.5pF 548 200 0.3±0.03 R
UMK063 CG7R5[]T-F CG C0G 7.5 p ±0.1pF, ±0.25pF, ±0.5pF 550 200 0.3±0.03 R
UMK063 CG7R6[]T-F CG C0G 7.6 p ±0.1pF, ±0.25pF, ±0.5pF 552 200 0.3±0.03 R
UMK063 CG7R7[]T-F CG C0G 7.7 p ±0.1pF, ±0.25pF, ±0.5pF 554 200 0.3±0.03 R
UMK063 CG7R8[]T-F CG C0G 7.8 p ±0.1pF, ±0.25pF, ±0.5pF 556 200 0.3±0.03 R
UMK063 CG7R9[]T-F CG C0G 7.9 p ±0.1pF, ±0.25pF, ±0.5pF 558 200 0.3±0.03 R
UMK063 CG080[]T-F CG C0G 8 p ±0.1pF, ±0.25pF, ±0.5pF 560 200 0.3±0.03 R
UMK063 CG8R1[]T-F CG C0G 8.1 p ±0.1pF, ±0.25pF, ±0.5pF 562 200 0.3±0.03 R
UMK063 CG8R2[]T-F CG C0G 8.2 p ±0.1pF, ±0.25pF, ±0.5pF 564 200 0.3±0.03 R
UMK063 CG8R3[]T-F CG C0G 8.3 p ±0.1pF, ±0.25pF, ±0.5pF 566 200 0.3±0.03 R
UMK063 CG8R4[]T-F CG C0G 8.4 p ±0.1pF, ±0.25pF, ±0.5pF 568 200 0.3±0.03 R
UMK063 CG8R5[]T-F CG C0G 8.5 p ±0.1pF, ±0.25pF, ±0.5pF 570 200 0.3±0.03 R
UMK063 CG8R6[]T-F CG C0G 8.6 p ±0.1pF, ±0.25pF, ±0.5pF 572 200 0.3±0.03 R
UMK063 CG8R7[]T-F CG C0G 8.7 p ±0.1pF, ±0.25pF, ±0.5pF 574 200 0.3±0.03 R
UMK063 CG8R8[]T-F CG C0G 8.8 p ±0.1pF, ±0.25pF, ±0.5pF 576 200 0.3±0.03 R
UMK063 CG8R9[]T-F CG C0G 8.9 p ±0.1pF, ±0.25pF, ±0.5pF 578 200 0.3±0.03 R
UMK063 CG090[]T-F CG C0G 9 p ±0.1pF, ±0.25pF, ±0.5pF 580 200 0.3±0.03 R
UMK063 CG9R1[]T-F CG C0G 9.1 p ±0.1pF, ±0.25pF, ±0.5pF 582 200 0.3±0.03 R
UMK063 CG9R2[]T-F CG C0G 9.2 p ±0.1pF, ±0.25pF, ±0.5pF 584 200 0.3±0.03 R
UMK063 CG9R3[]T-F CG C0G 9.3 p ±0.1pF, ±0.25pF, ±0.5pF 586 200 0.3±0.03 R
UMK063 CG9R4[]T-F CG C0G 9.4 p ±0.1pF, ±0.25pF, ±0.5pF 588 200 0.3±0.03 R
UMK063 CG9R5[]T-F CG C0G 9.5 p ±0.1pF, ±0.25pF, ±0.5pF 590 200 0.3±0.03 R
UMK063 CG9R6[]T-F CG C0G 9.6 p ±0.1pF, ±0.25pF, ±0.5pF 592 200 0.3±0.03 R
UMK063 CG9R7[]T-F CG C0G 9.7 p ±0.1pF, ±0.25pF, ±0.5pF 594 200 0.3±0.03 R
UMK063 CG9R8[]T-F CG C0G 9.8 p ±0.1pF, ±0.25pF, ±0.5pF 596 200 0.3±0.03 R
UMK063 CG9R9[]T-F CG C0G 9.9 p ±0.1pF, ±0.25pF, ±0.5pF 598 200 0.3±0.03 R
UMK063 CG100DT-F CG C0G 10 p ±0.5pF 600 200 0.3±0.03 R
UMK063 CG110JT-F CG C0G 11 p ±5％ 620 200 0.3±0.03 R
UMK063 CG120JT-F CG C0G 12 p ±5％ 640 200 0.3±0.03 R
UMK063 CG130JT-F CG C0G 13 p ±5％ 660 200 0.3±0.03 R
UMK063 CG150JT-F CG C0G 15 p ±5％ 700 200 0.3±0.03 R
UMK063 CG160JT-F CG C0G 16 p ±5％ 720 200 0.3±0.03 R
UMK063 CG180JT-F CG C0G 18 p ±5％ 760 200 0.3±0.03 R
UMK063 CG200JT-F CG C0G 20 p ±5％ 800 200 0.3±0.03 R
UMK063 CG220JT-F CG C0G 22 p ±5％ 840 200 0.3±0.03 R
UMK063 CG240JT-F CG C0G 24 p ±5％ 880 200 0.3±0.03 R
UMK063 CG270JT-F CG C0G 27 p ±5％ 940 200 0.3±0.03 R
UMK063 CG300JT-F CG C0G 30 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG330JT-F CG C0G 33 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG360JT-F CG C0G 36 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG390JT-F CG C0G 39 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG430JT-F CG C0G 43 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG470JT-F CG C0G 47 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG510JT-F CG C0G 51 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG560JT-F CG C0G 56 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG620JT-F CG C0G 62 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG680JT-F CG C0G 68 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG750JT-F CG C0G 75 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG820JT-F CG C0G 82 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG910JT-F CG C0G 91 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG101JT-F CG C0G 100 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG111JT-F CG C0G 110 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG121JT-F CG C0G 120 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG131JT-F CG C0G 130 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG151JT-F CG C0G 150 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG181JT-F CG C0G 180 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG201JT-F CG C0G 200 p ±5％ 1000 200 0.3±0.03 R
UMK063 CG221JT-F CG C0G 220 p ±5％ 1000 200 0.3±0.03 R
TMK063 CG241JT-F CG C0G 240 p ±5％ 1000 200 0.3±0.03 R
TMK063 CG271JT-F CG C0G 270 p ±5％ 1000 200 0.3±0.03 R
TMK063 CG301JT-F CG C0G 300 p ±5％ 1000 200 0.3±0.03 R
TMK063 CG331JT-F CG C0G 330 p ±5％ 1000 200 0.3±0.03 R
TMK063 CG361JT-F CG C0G 360 p ±5％ 1000 200 0.3±0.03 R
TMK063 CG391JT-F CG C0G 390 p ±5％ 1000 200 0.3±0.03 R
TMK063 CG431JT-F CG C0G 430 p ±5％ 1000 200 0.3±0.03 R
TMK063 CG471JT-F CG C0G 470 p ±5％ 1000 200 0.3±0.03 R
TMK063 CG511JT-F CG C0G 510 p ±5％ 1000 200 0.3±0.03 R
TMK063 CG561JT-F CG C0G 560 p ±5％ 1000 200 0.3±0.03 R
TMK063 CG621JT-F CG C0G 620 p ±5％ 1000 200 0.3±0.03 R
TMK063 CG681JT-F CG C0G 680 p ±5％ 1000 200 0.3±0.03 R
TMK063 CG751JT-F CG C0G 750 p ±5％ 1000 200 0.3±0.03 R
TMK063 CG821JT-F CG C0G 820 p ±5％ 1000 200 0.3±0.03 R
TMK063 CG911JT-F CG C0G 910 p ±5％ 1000 200 0.3±0.03 R
TMK063 CG102JT-F CG C0G 1000 p ±5％ 1000 200 0.3±0.03 R
50
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1MHz)
min
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
25
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
30
1
8
■PARTS NUMBER
●105TYPE
【Temperature Characteristic CG : CG/C0G】　0.5mm thickness（V）
HTLT
Rated voltage x ％
UMK105 CG0R5CV-F CG C0G 0.5 p ±0.25pF 410 200 0.5±0.05 R
UMK105 CG010CV-F CG C0G 1 p ±0.25pF 420 200 0.5±0.05 R
UMK105 CG1R5CV-F CG C0G 1.5 p ±0.25pF 430 200 0.5±0.05 R
UMK105 CG020CV-F CG C0G 2 p ±0.25pF 440 200 0.5±0.05 R
UMK105 CG030CV-F CG C0G 3 p ±0.25pF 460 200 0.5±0.05 R
UMK105 CG040CV-F CG C0G 4 p ±0.25pF 480 200 0.5±0.05 R
UMK105 CG050CV-F CG C0G 5 p ±0.25pF 500 200 0.5±0.05 R
UMK105 CG060DV-F CG C0G 6 p ±0.5pF 520 200 0.5±0.05 R
UMK105 CG070DV-F CG C0G 7 p ±0.5pF 540 200 0.5±0.05 R
UMK105 CG080DV-F CG C0G 8 p ±0.5pF 560 200 0.5±0.05 R
UMK105 CG090DV-F CG C0G 9 p ±0.5pF 580 200 0.5±0.05 R
UMK105 CG100DV-F CG C0G 10 p ±0.5pF 600 200 0.5±0.05 R
UMK105 CG120JV-F CG C0G 12 p ±5％ 640 200 0.5±0.05 R
UMK105 CG150JV-F CG C0G 15 p ±5％ 700 200 0.5±0.05 R
UMK105 CG180JV-F CG C0G 18 p ±5％ 760 200 0.5±0.05 R
UMK105 CG220JV-F CG C0G 22 p ±5％ 840 200 0.5±0.05 R
UMK105 CG270JV-F CG C0G 27 p ±5％ 940 200 0.5±0.05 R
UMK105 CG330JV-F CG C0G 33 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG390JV-F CG C0G 39 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG470JV-F CG C0G 47 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG560JV-F CG C0G 56 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG680JV-F CG C0G 68 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG820JV-F CG C0G 82 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG101JV-F CG C0G 100 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG121JV-F CG C0G 120 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG151JV-F CG C0G 150 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG181JV-F CG C0G 180 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG221JV-F CG C0G 220 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG271JV-F CG C0G 270 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG331JV-F CG C0G 330 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG391JV-F CG C0G 390 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG471JV-F CG C0G 470 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG561JV-F CG C0G 560 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG681JV-F CG C0G 680 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG821JV-F CG C0G 820 p ±5％ 1000 200 0.5±0.05 R
UMK105 CG102JV-F CG C0G 1000 p ±5％ 1000 200 0.5±0.05 R
【Temperature Characteristic U△ : U△/U2△】　0.5mm thickness（V）
HTLT
Rated voltage x ％
UMK105 UK0R5CV-F UK U2K 0.5 p ±0.25pF 410 200 0.5±0.05 R
UMK105 UK010CV-F UK U2K 1 p ±0.25pF 420 200 0.5±0.05 R
UMK105 UK1R5CV-F UK U2K 1.5 p ±0.25pF 430 200 0.5±0.05 R
UMK105 UK020CV-F UK U2K 2 p ±0.25pF 440 200 0.5±0.05 R
UMK105 UK030CV-F UK U2K 3 p ±0.25pF 460 200 0.5±0.05 R
UMK105 UJ040CV-F UJ U2J 4 p ±0.25pF 480 200 0.5±0.05 R
UMK105 UJ050CV-F UJ U2J 5 p ±0.25pF 500 200 0.5±0.05 R
UMK105 UJ060DV-F UJ U2J 6 p ±0.5pF 520 200 0.5±0.05 R
UMK105 UJ070DV-F UJ U2J 7 p ±0.5pF 540 200 0.5±0.05 R
UMK105 UJ080DV-F UJ U2J 8 p ±0.5pF 560 200 0.5±0.05 R
UMK105 UJ090DV-F UJ U2J 9 p ±0.5pF 580 200 0.5±0.05 R
UMK105 UJ100DV-F UJ U2J 10 p ±0.5pF 600 200 0.5±0.05 R
UMK105 UJ120JV-F UJ U2J 12 p ±5％ 640 200 0.5±0.05 R
UMK105 UJ150JV-F UJ U2J 15 p ±5％ 700 200 0.5±0.05 R
UMK105 UJ180JV-F UJ U2J 18 p ±5％ 760 200 0.5±0.05 R
UMK105 UJ220JV-F UJ U2J 22 p ±5％ 840 200 0.5±0.05 R
UMK105 UJ270JV-F UJ U2J 27 p ±5％ 940 200 0.5±0.05 R
UMK105 UJ330JV-F UJ U2J 33 p ±5％ 1000 200 0.5±0.05 R
UMK105 UJ390JV-F UJ U2J 39 p ±5％ 1000 200 0.5±0.05 R
UMK105 UJ470JV-F UJ U2J 47 p ±5％ 1000 200 0.5±0.05 R
UMK105 UJ560JV-F UJ U2J 56 p ±5％ 1000 200 0.5±0.05 R
UMK105 UJ680JV-F UJ U2J 68 p ±5％ 1000 200 0.5±0.05 R
UMK105 UJ820JV-F UJ U2J 82 p ±5％ 1000 200 0.5±0.05 R
UMK105 UJ101JV-F UJ U2J 100 p ±5％ 1000 200 0.5±0.05 R
UMK105 UJ121JV-F UJ U2J 120 p ±5％ 1000 200 0.5±0.05 R
UMK105 UJ151JV-F UJ U2J 150 p ±5％ 1000 200 0.5±0.05 R
UMK105 UJ181JV-F UJ U2J 180 p ±5％ 1000 200 0.5±0.05 R
UMK105 UJ221JV-F UJ U2J 220 p ±5％ 1000 200 0.5±0.05 R
UMK105 UJ271JV-F UJ U2J 270 p ±5％ 1000 200 0.5±0.05 R
UMK105 UJ331JV-F UJ U2J 330 p ±5％ 1000 200 0.5±0.05 R
【Temperature Characteristic SL】　0.5mm thickness（V）
HTLT
Rated voltage x ％
UMK105 SL121JV-F SL 120 p ±5％ 1000 200 0.5±0.05 R
UMK105 SL151JV-F SL 150 p ±5％ 1000 200 0.5±0.05 R
UMK105 SL181JV-F SL 180 p ±5％ 1000 200 0.5±0.05 R
UMK105 SL221JV-F SL 220 p ±5％ 1000 200 0.5±0.05 R
UMK105 SL271JV-F SL 270 p ±5％ 1000 200 0.5±0.05 R
UMK105 SL331JV-F SL 330 p ±5％ 1000 200 0.5±0.05 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1MHz)
min
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1MHz)
min
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1MHz)
min
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
31
1
8
■PARTS NUMBER
Multilayer Ceramic Capacitors for High Frequency Applications (1GHz+)
●021TYPE
【Temperature Characteristic CG : CG/C0G】　0.125mm thickness（K）
HTLT
Rated voltage x ％
TVS021 CG0R2[]K-W CG C0G 0.2 p ±0.05pF, ±0.1pF, ±0.25pF 260 200 0.125±0.013 R
TVS021 CG0R3[]K-W CG C0G 0.3 p ±0.05pF, ±0.1pF, ±0.25pF 260 200 0.125±0.013 R
TVS021 CG0R4[]K-W CG C0G 0.4 p ±0.05pF, ±0.1pF, ±0.25pF 260 200 0.125±0.013 R
TVS021 CG0R5[]K-W CG C0G 0.5 p ±0.05pF, ±0.1pF, ±0.25pF 260 200 0.125±0.013 R
TVS021 CG0R6[]K-W CG C0G 0.6 p ±0.05pF, ±0.1pF, ±0.25pF 260 200 0.125±0.013 R
TVS021 CG0R7[]K-W CG C0G 0.7 p ±0.05pF, ±0.1pF, ±0.25pF 260 200 0.125±0.013 R
TVS021 CGR75[]K-W CG C0G 0.75 p ±0.05pF, ±0.1pF, ±0.25pF 260 200 0.125±0.013 R
TVS021 CG0R8[]K-W CG C0G 0.8 p ±0.05pF, ±0.1pF, ±0.25pF 260 200 0.125±0.013 R
TVS021 CG0R9[]K-W CG C0G 0.9 p ±0.05pF, ±0.1pF, ±0.25pF 260 200 0.125±0.013 R
TVS021 CG010[]K-W CG C0G 1 p ±0.05pF, ±0.1pF, ±0.25pF 260 200 0.125±0.013 R
TVS021 CG1R1[]K-W CG C0G 1.1 p ±0.05pF, ±0.1pF, ±0.25pF 260 200 0.125±0.013 R
TVS021 CG1R2[]K-W CG C0G 1.2 p ±0.05pF, ±0.1pF, ±0.25pF 250 200 0.125±0.013 R
TVS021 CG1R3[]K-W CG C0G 1.3 p ±0.05pF, ±0.1pF, ±0.25pF 230 200 0.125±0.013 R
TVS021 CG1R4[]K-W CG C0G 1.4 p ±0.05pF, ±0.1pF, ±0.25pF 220 200 0.125±0.013 R
TVS021 CG1R5[]K-W CG C0G 1.5 p ±0.05pF, ±0.1pF, ±0.25pF 210 200 0.125±0.013 R
TVS021 CG1R6[]K-W CG C0G 1.6 p ±0.05pF, ±0.1pF, ±0.25pF 190 200 0.125±0.013 R
TVS021 CG1R7[]K-W CG C0G 1.7 p ±0.05pF, ±0.1pF, ±0.25pF 190 200 0.125±0.013 R
TVS021 CG1R8[]K-W CG C0G 1.8 p ±0.05pF, ±0.1pF, ±0.25pF 180 200 0.125±0.013 R
TVS021 CG1R9[]K-W CG C0G 1.9 p ±0.05pF, ±0.1pF, ±0.25pF 170 200 0.125±0.013 R
TVS021 CG020[]K-W CG C0G 2 p ±0.05pF, ±0.1pF, ±0.25pF 160 200 0.125±0.013 R
TVS021 CG2R1[]K-W CG C0G 2.1 p ±0.05pF, ±0.1pF, ±0.25pF 160 200 0.125±0.013 R
TVS021 CG2R2[]K-W CG C0G 2.2 p ±0.05pF, ±0.1pF, ±0.25pF 150 200 0.125±0.013 R
TVS021 CG2R3[]K-W CG C0G 2.3 p ±0.05pF, ±0.1pF, ±0.25pF 150 200 0.125±0.013 R
TVS021 CG2R4[]K-W CG C0G 2.4 p ±0.05pF, ±0.1pF, ±0.25pF 140 200 0.125±0.013 R
TVS021 CG2R5[]K-W CG C0G 2.5 p ±0.05pF, ±0.1pF, ±0.25pF 140 200 0.125±0.013 R
TVS021 CG2R6[]K-W CG C0G 2.6 p ±0.05pF, ±0.1pF, ±0.25pF 130 200 0.125±0.013 R
TVS021 CG2R7[]K-W CG C0G 2.7 p ±0.05pF, ±0.1pF, ±0.25pF 130 200 0.125±0.013 R
TVS021 CG2R8[]K-W CG C0G 2.8 p ±0.05pF, ±0.1pF, ±0.25pF 120 200 0.125±0.013 R
TVS021 CG2R9[]K-W CG C0G 2.9 p ±0.05pF, ±0.1pF, ±0.25pF 120 200 0.125±0.013 R
TVS021 CG030[]K-W CG C0G 3 p ±0.1pF, ±0.25pF, ±0.5pF 120 200 0.125±0.01
3R
TVS021 CG3R1[]K-W CG C0G 3.1 p ±0.1pF, ±0.25pF, ±0.5pF 110 200 0.125±0.013 R
TVS021 CG3R2[]K-W CG C0G 3.2 p ±0.1pF, ±0.25pF, ±0.5pF 110 200 0.125±0.013 R
TVS021 CG3R3[]K-W CG C0G 3.3 p ±0.1pF, ±0.25pF, ±0.5pF 110 200 0.125±0.013 R
TVS021 CG3R4[]K-W CG C0G 3.4 p ±0.1pF, ±0.25pF, ±0.5pF 110 200 0.125±0.013 R
TVS021 CG3R5[]K-W CG C0G 3.5 p ±0.1pF, ±0.25pF, ±0.5pF 100 200 0.125±0.013 R
TVS021 CG3R6[]K-W CG C0G 3.6 p ±0.1pF, ±0.25pF, ±0.5pF 100 200 0.125±0.013 R
TVS021 CG3R7[]K-W CG C0G 3.7 p ±0.1pF, ±0.25pF, ±0.5pF 100 200 0.125±0.013 R
TVS021 CG3R8[]K-W CG C0G 3.8 p ±0.1pF, ±0.25pF, ±0.5pF 100 200 0.125±0.013 R
TVS021 CG3R9[]K-W CG C0G 3.9 p ±0.1pF, ±0.25pF, ±0.5pF 90 200 0.125±0.013 R
TVS021 CG040[]K-W CG C0G 4 p ±0.1pF, ±0.25pF, ±0.5pF 90 200 0.125±0.013 R
TVS021 CG4R1[]K-W CG C0G 4.1 p ±0.1pF, ±0.25pF, ±0.5pF 90 200 0.125±0.013 R
TVS021 CG4R2[]K-W CG C0G 4.2 p ±0.1pF, ±0.25pF, ±0.5pF 90 200 0.125±0.013 R
TVS021 CG4R3[]K-W CG C0G 4.3 p ±0.1pF, ±0.25pF, ±0.5pF 90 200 0.125±0.013 R
TVS021 CG4R4[]K-W CG C0G 4.4 p ±0.1pF, ±0.25pF, ±0.5pF 90 200 0.125±0.013 R
TVS021 CG4R5[]K-W CG C0G 4.5 p ±0.1pF, ±0.25pF, ±0.5pF 80 200 0.125±0.013 R
TVS021 CG4R6[]K-W CG C0G 4.6 p ±0.1pF, ±0.25pF, ±0.5pF 80 200 0.125±0.013 R
TVS021 CG4R7[]K-W CG C0G 4.7 p ±0.1pF, ±0.25pF, ±0.5pF 80 200 0.125±0.013 R
TVS021 CG4R8[]K-W CG C0G 4.8 p ±0.1pF, ±0.25pF, ±0.5pF 80 200 0.125±0.013 R
TVS021 CG4R9[]K-W CG C0G 4.9 p ±0.1pF, ±0.25pF, ±0.5pF 80 200 0.125±0.013 R
TVS021 CG050[]K-W CG C0G 5 p ±0.1pF, ±0.25pF, ±0.5pF 80 200 0.125±0.013 R
TVS021 CG5R1[]K-W CG C0G 5.1 p ±0.1pF, ±0.25pF, ±0.5pF 80 200 0.125±0.013 R
EVS021 CG5R2[]K-W CG C0G 5.2 p ±0.1pF, ±0.25pF, ±0.5pF 70 200 0.125±0.013 R
EVS021 CG5R3[]K-W CG C0G 5.3 p ±0.1pF, ±0.25pF, ±0.5pF 70 200 0.125±0.013 R
EVS021 CG5R4[]K-W CG C0G 5.4 p ±0.1pF, ±0.25pF, ±0.5pF 70 200 0.125±0.013 R
EVS021 CG5R5[]K-W CG C0G 5.5 p ±0.1pF, ±0.25pF, ±0.5pF 70 200 0.125±0.013 R
EVS021 CG5R6[]K-W CG C0G 5.6 p ±0.1pF, ±0.25pF, ±0.5pF 70 200 0.125±0.013 R
EVS021 CG5R7[]K-W CG C0G 5.7 p ±0.1pF, ±0.25pF, ±0.5pF 70 200 0.125±0.013 R
EVS021 CG5R8[]K-W CG C0G 5.8 p ±0.1pF, ±0.25pF, ±0.5pF 70 200 0.125±0.013 R
EVS021 CG5R9[]K-W CG C0G 5.9 p ±0.1pF, ±0.25pF, ±0.5pF 70 200 0.125±0.013 R
EVS021 CG060[]K-W CG C0G 6 p ±0.1pF, ±0.25pF, ±0.5pF 70 200 0.125±0.013 R
EVS021 CG6R1[]K-W CG C0G 6.1 p ±0.1pF, ±0.25pF, ±0.5pF 70 200 0.125±0.013 R
EVS021 CG6R2[]K-W CG C0G 6.2 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.125±0.013 R
EVS021 CG6R3[]K-W CG C0G 6.3 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.125±0.013 R
EVS021 CG6R4[]K-W CG C0G 6.4 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.125±0.013 R
EVS021 CG6R5[]K-W CG C0G 6.5 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.125±0.013 R
EVS021 CG6R6[]K-W CG C0G 6.6 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.125±0.013 R
EVS021 CG6R7[]K-W CG C0G 6.7 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.125±0.013 R
EVS021 CG6R8[]K-W CG C0G 6.8 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.125±0.013 R
EVS021 CG6R9[]K-W CG C0G 6.9 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.125±0.013 R
EVS021 CG070[]K-W CG C0G 7 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.125±0.013 R
EVS021 CG7R1[]K-W CG C0G 7.1 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.125±0.013 R
EVS021 CG7R2[]K-W CG C0G 7.2 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.125±0.013 R
EVS021 CG7R3[]K-W CG C0G 7.3 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.125±0.013 R
EVS021 CG7R4[]K-W CG C0G 7.4 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.125±0.013 R
EVS021 CG7R5[]K-W CG C0G 7.5 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.125±0.013 R
EVS021 CG7R6[]K-W CG C0G 7.6 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.125±0.013 R
EVS021 CG7R7[]K-W CG C0G 7.7 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG7R8[]K-W CG C0G 7.8 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG7R9[]K-W CG C0G 7.9 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG080[]K-W CG C0G 8 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG8R1[]K-W CG C0G 8.1 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG8R2[]K-W CG C0G 8.2 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG8R3[]K-W CG C0G 8.3 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG8R4[]K-W CG C0G 8.4 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG8R5[]K-W CG C0G 8.5 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
16
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1GHz)
(min)
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
25
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
32
1
8
■PARTS NUMBER
HTLT
Rated voltage x ％
EVS021 CG8R6[]K-W CG C0G 8.6 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG8R7[]K-W CG C0G 8.7 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG8R8[]K-W CG C0G 8.8 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG8R9[]K-W CG C0G 8.9 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG090[]K-W CG C0G 9 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG9R1[]K-W CG C0G 9.1 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG9R2[]K-W CG C0G 9.2 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG9R3[]K-W CG C0G 9.3 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG9R4[]K-W CG C0G 9.4 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG9R5[]K-W CG C0G 9.5 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG9R6[]K-W CG C0G 9.6 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG9R7[]K-W CG C0G 9.7 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.125±0.013 R
EVS021 CG9R8[]K-W CG C0G 9.8 p ±0.1pF, ±0.25pF, ±0.5pF 40 200 0.125±0.013 R
EVS021 CG9R9[]K-W CG C0G 9.9 p ±0.1pF, ±0.25pF, ±0.5pF 40 200 0.125±0.013 R
EVS021 CG100[]K-W CG C0G 10 p ±2％, ±5％ 50 200 0.125±0.013 R
●042TYPE
【Temperature Characteristic CG : CG/C0G】　0.2mm thickness（C）
HTLT
Rated voltage x ％
TVS042 CG0R2[]C-W CG C0G 0.2 p ±0.05pF, ±0.1pF, ±0.25pF 300 200 0.2±0.0
2R
TVS042 CG0R3[]C-W CG C0G 0.3 p ±0.05pF, ±0.1pF, ±0.25pF 300 200 0.2±0.0
2R
TVS042 CG0R4[]C-W CG C0G 0.4 p ±0.05pF, ±0.1pF, ±0.25pF 300 200 0.2±0.0
2R
TVS042 CG0R5[]C-W CG C0G 0.5 p ±0.05pF, ±0.1pF, ±0.25pF 300 200 0.2±0.0
2R
TVS042 CG0R6[]C-W CG C0G 0.6 p ±0.05pF, ±0.1pF, ±0.25pF 300 200 0.2±0.0
2R
TVS042 CG0R7[]C-W CG C0G 0.7 p ±0.05pF, ±0.1pF, ±0.25pF 300 200 0.2±0.0
2R
TVS042 CGR75[]C-W CG C0G 0.75 p ±0.05pF, ±0.1pF, ±0.25pF 300 200 0.2±0.02 R
TVS042 CG0R8[]C-W CG C0G 0.8 p ±0.05pF, ±0.1pF, ±0.25pF 300 200 0.2±0.0
2R
TVS042 CG0R9[]C-W CG C0G 0.9 p ±0.05pF, ±0.1pF, ±0.25pF 300 200 0.2±0.0
2R
TVS042 CG010[]C-W CG C0G 1 p ±0.05pF, ±0.1pF, ±0.25pF 300 200 0.2±0.02 R
TVS042 CG1R1[]C-W CG C0G 1.1 p ±0.05pF, ±0.1pF, ±0.25pF 280 200 0.2±0.0
2R
TVS042 CG1R2[]C-W CG C0G 1.2 p ±0.05pF, ±0.1pF, ±0.25pF 270 200 0.2±0.0
2R
TVS042 CG1R3[]C-W CG C0G 1.3 p ±0.05pF, ±0.1pF, ±0.25pF 260 200 0.2±0.0
2R
TVS042 CG1R4[]C-W CG C0G 1.4 p ±0.05pF, ±0.1pF, ±0.25pF 250 200 0.2±0.0
2R
TVS042 CG1R5[]C-W CG C0G 1.5 p ±0.05pF, ±0.1pF, ±0.25pF 240 200 0.2±0.0
2R
TVS042 CG1R6[]C-W CG C0G 1.6 p ±0.05pF, ±0.1pF, ±0.25pF 230 200 0.2±0.0
2R
TVS042 CG1R7[]C-W CG C0G 1.7 p ±0.05pF, ±0.1pF, ±0.25pF 220 200 0.2±0.0
2R
TVS042 CG1R8[]C-W CG C0G 1.8 p ±0.05pF, ±0.1pF, ±0.25pF 210 200 0.2±0.0
2R
TVS042 CG1R9[]C-W CG C0G 1.9 p ±0.05pF, ±0.1pF, ±0.25pF 200 200 0.2±0.0
2R
TVS042 CG020[]C-W CG C0G 2 p ±0.05pF, ±0.1pF, ±0.25pF 190 200 0.2±0.02 R
TVS042 CG2R1[]C-W CG C0G 2.1 p ±0.05pF, ±0.1pF, ±0.25pF 185 200 0.2±0.0
2R
TVS042 CG2R2[]C-W CG C0G 2.2 p ±0.05pF, ±0.1pF, ±0.25pF 180 200 0.2±0.0
2R
TVS042 CG2R3[]C-W CG C0G 2.3 p ±0.05pF, ±0.1pF, ±0.25pF 175 200 0.2±0.0
2R
TVS042 CG2R4[]C-W CG C0G 2.4 p ±0.05pF, ±0.1pF, ±0.25pF 170 200 0.2±0.0
2R
TVS042 CG2R5[]C-W CG C0G 2.5 p ±0.05pF, ±0.1pF, ±0.25pF 160 200 0.2±0.0
2R
TVS042 CG2R6[]C-W CG C0G 2.6 p ±0.05pF, ±0.1pF, ±0.25pF 155 200 0.2±0.0
2R
TVS042 CG2R7[]C-W CG C0G 2.7 p ±0.05pF, ±0.1pF, ±0.25pF 150 200 0.2±0.0
2R
TVS042 CG2R8[]C-W CG C0G 2.8 p ±0.05pF, ±0.1pF, ±0.25pF 140 200 0.2±0.0
2R
TVS042 CG2R9[]C-W CG C0G 2.9 p ±0.05pF, ±0.1pF, ±0.25pF 135 200 0.2±0.0
2R
TVS042 CG030[]C-W CG C0G 3 p ±0.05pF, ±0.1pF, ±0.25pF 130 200 0.2±0.02 R
TVS042 CG3R1[]C-W CG C0G 3.1 p ±0.1pF, ±0.25pF 125 200 0.2±0.02 R
TVS042 CG3R2[]C-W CG C0G 3.2 p ±0.1pF, ±0.25pF 125 200 0.2±0.02 R
TVS042 CG3R3[]C-W CG C0G 3.3 p ±0.1pF, ±0.25pF 120 200 0.2±0.02 R
TVS042 CG3R4[]C-W CG C0G 3.4 p ±0.1pF, ±0.25pF 120 200 0.2±0.02 R
TVS042 CG3R5[]C-W CG C0G 3.5 p ±0.1pF, ±0.25pF 110 200 0.2±0.02 R
TVS042 CG3R6[]C-W CG C0G 3.6 p ±0.1pF, ±0.25pF 110 200 0.2±0.02 R
TVS042 CG3R7[]C-W CG C0G 3.7 p ±0.1pF, ±0.25pF 110 200 0.2±0.02 R
TVS042 CG3R8[]C-W CG C0G 3.8 p ±0.1pF, ±0.25pF 100 200 0.2±0.02 R
TVS042 CG3R9[]C-W CG C0G 3.9 p ±0.1pF, ±0.25pF 100 200 0.2±0.02 R
TVS042 CG040[]C-W CG C0G 4 p ±0.1pF, ±0.25pF 90 200 0.2±0.02 R
TVS042 CG4R1[]C-W CG C0G 4.1 p ±0.1pF, ±0.25pF 90 200 0.2±0.02 R
TVS042 CG4R2[]C-W CG C0G 4.2 p ±0.1pF, ±0.25pF 85 200 0.2±0.02 R
TVS042 CG4R3[]C-W CG C0G 4.3 p ±0.1pF, ±0.25pF 85 200 0.2±0.02 R
TVS042 CG4R4[]C-W CG C0G 4.4 p ±0.1pF, ±0.25pF 85 200 0.2±0.02 R
TVS042 CG4R5[]C-W CG C0G 4.5 p ±0.1pF, ±0.25pF 85 200 0.2±0.02 R
TVS042 CG4R6[]C-W CG C0G 4.6 p ±0.1pF, ±0.25pF 85 200 0.2±0.02 R
TVS042 CG4R7[]C-W CG C0G 4.7 p ±0.1pF, ±0.25pF 85 200 0.2±0.02 R
TVS042 CG4R8[]C-W CG C0G 4.8 p ±0.1pF, ±0.25pF 80 200 0.2±0.02 R
TVS042 CG4R9[]C-W CG C0G 4.9 p ±0.1pF, ±0.25pF 80 200 0.2±0.02 R
TVS042 CG050[]C-W CG C0G 5 p ±0.1pF, ±0.25pF 80 200 0.2±0.02 R
TVS042 CG5R1[]C-W CG C0G 5.1 p ±0.1pF, ±0.25pF, ±0.5pF 75 200 0.2±0.02 R
TVS042 CG5R2[]C-W CG C0G 5.2 p ±0.1pF, ±0.25pF, ±0.5pF 75 200 0.2±0.02 R
TVS042 CG5R3[]C-W CG C0G 5.3 p ±0.1pF, ±0.25pF, ±0.5pF 75 200 0.2±0.02 R
TVS042 CG5R4[]C-W CG C0G 5.4 p ±0.1pF, ±0.25pF, ±0.5pF 70 200 0.2±0.02 R
TVS042 CG5R5[]C-W CG C0G 5.5 p ±0.1pF, ±0.25pF, ±0.5pF 70 200 0.2±0.02 R
TVS042 CG5R6[]C-W CG C0G 5.6 p ±0.1pF, ±0.25pF, ±0.5pF 70 200 0.2±0.02 R
TVS042 CG5R7[]C-W CG C0G 5.7 p ±0.1pF, ±0.25pF, ±0.5pF 70 200 0.2±0.02 R
TVS042 CG5R8[]C-W CG C0G 5.8 p ±0.1pF, ±0.25pF, ±0.5pF 70 200 0.2±0.02 R
TVS042 CG5R9[]C-W CG C0G 5.9 p ±0.1pF, ±0.25pF, ±0.5pF 65 200 0.2±0.02 R
TVS042 CG060[]C-W CG C0G 6 p ±0.1pF, ±0.25pF, ±0.5pF 65 200 0.2±0.02 R
TVS042 CG6R1[]C-W CG C0G 6.1 p ±0.1pF, ±0.25pF, ±0.5pF 65 200 0.2±0.02 R
TVS042 CG6R2[]C-W CG C0G 6.2 p ±0.1pF, ±0.25pF, ±0.5pF 65 200 0.2±0.02 R
TVS042 CG6R3[]C-W CG C0G 6.3 p ±0.1pF, ±0.25pF, ±0.5pF 65 200 0.2±0.02 R
TVS042 CG6R4[]C-W CG C0G 6.4 p ±0.1pF, ±0.25pF, ±0.5pF 65 200 0.2±0.02 R
TVS042 CG6R5[]C-W CG C0G 6.5 p ±0.1pF, ±0.25pF, ±0.5pF 65 200 0.2±0.02 R
TVS042 CG6R6[]C-W CG C0G 6.6 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.2±0.02 R
TVS042 CG6R7[]C-W CG C0G 6.7 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.2±0.02 R
25
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1GHz)
(min)
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
16
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1GHz)
(min)
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
33
1
8
■PARTS NUMBER
HTLT
Rated voltage x ％
TVS042 CG6R8[]C-W CG C0G 6.8 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.2±0.02 R
TVS042 CG6R9[]C-W CG C0G 6.9 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.2±0.02 R
TVS042 CG070[]C-W CG C0G 7 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.2±0.02 R
TVS042 CG7R1[]C-W CG C0G 7.1 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.2±0.02 R
TVS042 CG7R2[]C-W CG C0G 7.2 p ±0.1pF, ±0.25pF, ±0.5pF 60 200 0.2±0.02 R
TVS042 CG7R3[]C-W CG C0G 7.3 p ±0.1pF, ±0.25pF, ±0.5pF 55 200 0.2±0.02 R
TVS042 CG7R4[]C-W CG C0G 7.4 p ±0.1pF, ±0.25pF, ±0.5pF 55 200 0.2±0.02 R
TVS042 CG7R5[]C-W CG C0G 7.5 p ±0.1pF, ±0.25pF, ±0.5pF 55 200 0.2±0.02 R
TVS042 CG7R6[]C-W CG C0G 7.6 p ±0.1pF, ±0.25pF, ±0.5pF 55 200 0.2±0.02 R
TVS042 CG7R7[]C-W CG C0G 7.7 p ±0.1pF, ±0.25pF, ±0.5pF 55 200 0.2±0.02 R
TVS042 CG7R8[]C-W CG C0G 7.8 p ±0.1pF, ±0.25pF, ±0.5pF 55 200 0.2±0.02 R
TVS042 CG7R9[]C-W CG C0G 7.9 p ±0.1pF, ±0.25pF, ±0.5pF 55 200 0.2±0.02 R
TVS042 CG080[]C-W CG C0G 8 p ±0.1pF, ±0.25pF, ±0.5pF 55 200 0.2±0.02 R
TVS042 CG8R1[]C-W CG C0G 8.1 p ±0.1pF, ±0.25pF, ±0.5pF 55 200 0.2±0.02 R
TVS042 CG8R2[]C-W CG C0G 8.2 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.2±0.02 R
TVS042 CG8R3[]C-W CG C0G 8.3 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.2±0.02 R
TVS042 CG8R4[]C-W CG C0G 8.4 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.2±0.02 R
TVS042 CG8R5[]C-W CG C0G 8.5 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.2±0.02 R
TVS042 CG8R6[]C-W CG C0G 8.6 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.2±0.02 R
TVS042 CG8R7[]C-W CG C0G 8.7 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.2±0.02 R
TVS042 CG8R8[]C-W CG C0G 8.8 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.2±0.02 R
TVS042 CG8R9[]C-W CG C0G 8.9 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.2±0.02 R
TVS042 CG090[]C-W CG C0G 9 p ±0.1pF, ±0.25pF, ±0.5pF 50 200 0.2±0.02 R
TVS042 CG9R1[]C-W CG C0G 9.1 p ±0.1pF, ±0.25pF, ±0.5pF 45 200 0.2±0.02 R
TVS042 CG9R2[]C-W CG C0G 9.2 p ±0.1pF, ±0.25pF, ±0.5pF 45 200 0.2±0.02 R
TVS042 CG9R3[]C-W CG C0G 9.3 p ±0.1pF, ±0.25pF, ±0.5pF 45 200 0.2±0.02 R
TVS042 CG9R4[]C-W CG C0G 9.4 p ±0.1pF, ±0.25pF, ±0.5pF 45 200 0.2±0.02 R
TVS042 CG9R5[]C-W CG C0G 9.5 p ±0.1pF, ±0.25pF, ±0.5pF 45 200 0.2±0.02 R
TVS042 CG9R6[]C-W CG C0G 9.6 p ±0.1pF, ±0.25pF, ±0.5pF 45 200 0.2±0.02 R
TVS042 CG9R7[]C-W CG C0G 9.7 p ±0.1pF, ±0.25pF, ±0.5pF 45 200 0.2±0.02 R
TVS042 CG9R8[]C-W CG C0G 9.8 p ±0.1pF, ±0.25pF, ±0.5pF 45 200 0.2±0.02 R
TVS042 CG9R9[]C-W CG C0G 9.9 p ±0.1pF, ±0.25pF, ±0.5pF 45 200 0.2±0.02 R
TVS042 CG100[]C-W CG C0G 10 p ±2％, ±5％ 45 200 0.2±0.02 R
TVS042 CG110JC-W CG C0G 11 p ±5％ 40 200 0.2±0.02 R
TVS042 CG120JC-W CG C0G 12 p ±5％ 40 200 0.2±0.02 R
TVS042 CG130JC-W CG C0G 13 p ±5％ 40 200 0.2±0.02 R
TVS042 CG150JC-W CG C0G 15 p ±5％ 40 200 0.2±0.02 R
TVS042 CG160JC-W CG C0G 16 p ±5％ 40 200 0.2±0.02 R
TVS042 CG180JC-W CG C0G 18 p ±5％ 40 200 0.2±0.02 R
TVS042 CG220JC-W CG C0G 22 p ±5％ 30 200 0.2±0.02 R
●105TYPE
【Temperature Characteristic CG : CG/C0G】　0.5mm thickness（W）
HTLT
Rated voltage x ％
EVK105 CG0R3BW-F CG C0G 0.3 p ±0.1pF 300 200 0.5±0.05 R
EVK105 CG0R4BW-F CG C0G 0.4 p ±0.1pF 300 200 0.5±0.05 R
EVK105 CG0R5BW-F CG C0G 0.5 p ±0.1pF 300 200 0.5±0.05 R
EVK105 CG0R6BW-F CG C0G 0.6 p ±0.1pF 300 200 0.5±0.05 R
EVK105 CG0R7BW-F CG C0G 0.7 p ±0.1pF 300 200 0.5±0.05 R
EVK105 CG0R8BW-F CG C0G 0.8 p ±0.1pF 300 200 0.5±0.05 R
EVK105 CG0R9BW-F CG C0G 0.9 p ±0.1pF 300 200 0.5±0.05 R
EVK105 CG010BW-F CG C0G 1 p ±0.1pF 300 200 0.5±0.05 R
EVK105 CG1R1BW-F CG C0G 1.1 p ±0.1pF 280 200 0.5±0.05 R
EVK105 CG1R2BW-F CG C0G 1.2 p ±0.1pF 270 200 0.5±0.05 R
EVK105 CG1R3BW-F CG C0G 1.3 p ±0.1pF 260 200 0.5±0.05 R
EVK105 CG1R5BW-F CG C0G 1.5 p ±0.1pF 240 200 0.5±0.05 R
EVK105 CG1R6BW-F CG C0G 1.6 p ±0.1pF 230 200 0.5±0.05 R
EVK105 CG1R8BW-F CG C0G 1.8 p ±0.1pF 210 200 0.5±0.05 R
EVK105 CG020BW-F CG C0G 2 p ±0.1pF 190 200 0.5±0.05 R
EVK105 CG2R2JW-F CG C0G 2.2 p ±5％ 180 200 0.5±0.05 R
EVK105 CG2R4JW-F CG C0G 2.4 p ±5％ 170 200 0.5±0.05 R
EVK105 CG2R7JW-F CG C0G 2.7 p ±5％ 150 200 0.5±0.05 R
EVK105 CG030JW-F CG C0G 3 p ±5％ 130 200 0.5±0.05 R
EVK105 CG3R3JW-F CG C0G 3.3 p ±5％ 120 200 0.5±0.05 R
EVK105 CG3R6JW-F CG C0G 3.6 p ±5％ 110 200 0.5±0.05 R
EVK105 CG3R9JW-F CG C0G 3.9 p ±5％ 99 200 0.5±0.05 R
EVK105 CG4R3JW-F CG C0G 4.3 p ±5％ 84 200 0.5±0.05 R
EVK105 CG4R7JW-F CG C0G 4.7 p ±5％ 84 200 0.5±0.05 R
EVK105 CG5R1JW-F CG C0G 5.1 p ±5％ 84 200 0.5±0.05 R
Q
(at 1GHz)
(min)
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
25
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1GHz)
(min)
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
16
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
34
1
8
■PARTS NUMBER
【Temperature Characteristic CG : CG/C0G】　0.5mm thickness（W）
HTLT
Rated voltage x ％
UVK105 CG0R3BW-F CG C0G 0.3 p ±0.1pF 300 200 0.5±0.05 R
UVK105 CG0R4BW-F CG C0G 0.4 p ±0.1pF 300 200 0.5±0.05 R
UVK105 CG0R5BW-F CG C0G 0.5 p ±0.1pF 300 200 0.5±0.05 R
UVK105 CG0R6BW-F CG C0G 0.6 p ±0.1pF 300 200 0.5±0.05 R
UVK105 CG0R7BW-F CG C0G 0.7 p ±0.1pF 300 200 0.5±0.05 R
UVK105 CG0R8BW-F CG C0G 0.8 p ±0.1pF 300 200 0.5±0.05 R
UVK105 CG0R9BW-F CG C0G 0.9 p ±0.1pF 300 200 0.5±0.05 R
UVK105 CG010BW-F CG C0G 1 p ±0.1pF 300 200 0.5±0.05 R
UVK105 CG1R1BW-F CG C0G 1.1 p ±0.1pF 280 200 0.5±0.05 R
UVK105 CG1R2BW-F CG C0G 1.2 p ±0.1pF 270 200 0.5±0.05 R
UVK105 CG1R3BW-F CG C0G 1.3 p ±0.1pF 260 200 0.5±0.05 R
UVK105 CG1R5BW-F CG C0G 1.5 p ±0.1pF 240 200 0.5±0.05 R
UVK105 CG1R6BW-F CG C0G 1.6 p ±0.1pF 230 200 0.5±0.05 R
UVK105 CG1R8BW-F CG C0G 1.8 p ±0.1pF 210 200 0.5±0.05 R
UVK105 CG020BW-F CG C0G 2 p ±0.1pF 190 200 0.5±0.05 R
UVK105 CG2R2JW-F CG C0G 2.2 p ±5％ 180 200 0.5±0.05 R
UVK105 CG2R4JW-F CG C0G 2.4 p ±5％ 170 200 0.5±0.05 R
UVK105 CG2R7JW-F CG C0G 2.7 p ±5％ 150 200 0.5±0.05 R
UVK105 CG030JW-F CG C0G 3 p ±5％ 130 200 0.5±0.05 R
UVK105 CG3R3JW-F CG C0G 3.3 p ±5％ 120 200 0.5±0.05 R
UVK105 CG3R6JW-F CG C0G 3.6 p ±5％ 110 200 0.5±0.05 R
UVK105 CG3R9JW-F CG C0G 3.9 p ±5％ 99 200 0.5±0.05 R
UVK105 CG4R3JW-F CG C0G 4.3 p ±5％ 84 200 0.5±0.05 R
UVK105 CG4R7JW-F CG C0G 4.7 p ±5％ 84 200 0.5±0.05 R
UVK105 CG5R1JW-F CG C0G 5.1 p ±5％ 84 200 0.5±0.05 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1GHz)
(min)
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
35
1
8
■PARTS NUMBER
Super Low Distortion Multilayer Ceramic Capacitors
●105TYPE
【Temperature Characteristic SD : Standard】　0.5mm thickness（V）
HTLT
Rated voltage x ％
UMK105 SD391KV-F 390 p ±10 0.1 200 0.5±0.05 R
UMK105 SD471KV-F 470 p ±10 0.1 200 0.5±0.05 R
UMK105 SD561KV-F 560 p ±10 0.1 200 0.5±0.05 R
TMK105 SD681KV-F 680 p ±10 0.1 200 0.5±0.05 R
TMK105 SD821KV-F 820 p ±10 0.1 200 0.5±0.05 R
TMK105 SD102KV-F 1000 p ±10 0.1 200 0.5±0.05 R
TMK105 SD122KV-F 1200 p ±10 0.1 200 0.5±0.05 R
EMK105 SD152KV-F 1500 p ±10 0.1 200 0.5±0.05 R
EMK105 SD182KV-F 1800 p ±10 0.1 200 0.5±0.05 R
EMK105 SD222KV-F 2200 p ±10 0.1 200 0.5±0.05 R
EMK105 SD272KV-F 2700 p ±10 0.1 200 0.5±0.05 R
LMK105 SD332KV-F 3300 p ±10 0.1 200 0.5±0.05 R
LMK105 SD392KV-F 3900 p ±10 0.1 200 0.5±0.05 R
LMK105 SD472KV-F 4700 p ±10 0.1 200 0.5±0.05 R
【Temperature Characteristic SD : Standard】　0.3mm thickness（P）
HTLT
Rated voltage x ％
LMK105 SD152KP-F 10 1500 p ±10 0.1 200 0.3±0.03 R
JMK105 SD272KP-F 6.3 2700 p ±10 0.1 200 0.3±0.03 R
●107TYPE
【Temperature Characteristic SD : Standard】　0.8mm thickness（A）
HTLT
Rated voltage x ％
UMK107 SD102KA-T 1000 p ±10 0.1 200 0.8±0.10 R
UMK107 SD122KA-T 1200 p ±10 0.1 200 0.8±0.10 R
UMK107 SD152KA-T 1500 p ±10 0.1 200 0.8±0.10 R
UMK107 SD182KA-T 1800 p ±10 0.1 200 0.8±0.10 R
UMK107 SD222KA-T 2200 p ±10 0.1 200 0.8±0.10 R
UMK107 SD272KA-T 2700 p ±10 0.1 200 0.8±0.10 R
UMK107 SD332KA-T 3300 p ±10 0.1 200 0.8±0.10 R
TMK107 SD392KA-T 3900 p ±10 0.1 200 0.8±0.10 R
TMK107 SD472KA-T 4700 p ±10 0.1 200 0.8±0.10 R
EMK107 SD562KA-T 5600 p ±10 0.1 200 0.8±0.10 R
EMK107 SD682KA-T 6800 p ±10 0.1 200 0.8±0.10 R
EMK107 SD822KA-T 8200 p ±10 0.1 200 0.8±0.10 R
EMK107 SD103KA-T 0.01 μ ±10 0.1 200 0.8±0.10 R
LMK107 SD123KA-T 0.012 μ ±10 0.1 200 0.8±0.10 R
LMK107 SD153KA-T 0.015 μ ±10 0.1 200 0.8±0.10 R
LMK107 SD183KA-T 0.018 μ ±10 0.1 200 0.8±0.10 R
LMK107 SD223KA-T 0.022 μ ±10 0.1 200 0.8±0.10 R
●212TYPE
【Temperature Characteristic SD : Standard】　1.25mm thickness（G）
HTLT
Rated voltage x ％
GMK212 SD183KG-T 0.018 μ ±10 0.1 200 1.25±0.10 R
GMK212 SD223KG-T 0.022 μ ±10 0.1 200 1.25±0.10 R
GMK212 SD273KG-T 0.027 μ ±10 0.1 200 1.25±0.10 R
LMK212 SD683KG-T 0.068 μ ±10 0.1 200 1.25±0.10 R
LMK212 SD823KG-T 0.082 μ ±10 0.1 200 1.25±0.10 R
LMK212 SD104KG-T 0.1 μ ±10 0.1 200 1.25±0.10 R
【Temperature Characteristic SD : Standard】　0.85mm thickness（D）
HTLT
Rated voltage x ％
UMK212 SD392KD-T 3900 p ±10 0.1 200 0.85±0.10 R
UMK212 SD472KD-T 4700 p ±10 0.1 200 0.85±0.10 R
UMK212 SD562KD-T 5600 p ±10 0.1 200 0.85±0.10 R
UMK212 SD682KD-T 6800 p ±10 0.1 200 0.85±0.10 R
UMK212 SD822KD-T 8200 p ±10 0.1 200 0.85±0.10 R
UMK212 SD103KD-T 0.01 μ ±10 0.1 200 0.85±0.10 R
GMK212 SD123KD-T 0.012 μ ±10 0.1 200 0.85±0.10 R
GMK212 SD153KD-T 0.015 μ ±10 0.1 200 0.85±0.10 R
EMK212 SD333KD-T 16 0.033 μ ±10 0.1 200 0.85±0.10 R
LMK212 SD473KD-T 10 0.047 μ ±10 0.1 200 0.85±0.10 R
●316TYPE
【Temperature Characteristic SD : Standard】　1.6mm thickness（L）
HTLT
Rated voltage x ％
TMK316 SD823KL-T 0.082 μ ±10 0.1 200 1.6±0.20 R
TMK316 SD104KL-T 0.1 μ ±10 0.1 200 1.6±0.20 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
Standard Type
25
16
10
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Standard Type
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
Standard Type
25
16
10
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
35
Standard Type
10
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
50
Standard Type
35
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
25 Standard Type
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
36
1
8
■PARTS NUMBER
【Temperature Characteristic SD : Standard】　1.15mm thickness（F）
HTLT
Rated voltage x ％
GMK316 SD333KF-T 0.033 μ ±10 0.1 200 1.15±0.10 R
GMK316 SD393KF-T 0.039 μ ±10 0.1 200 1.15±0.10 R
TMK316 SD473KF-T 0.047 μ ±10 0.1 200 1.15±0.10 R
TMK316 SD563KF-T 0.056 μ ±10 0.1 200 1.15±0.10 R
TMK316 SD683KF-T 0.068 μ ±10 0.1 200 1.15±0.10 R
Low Distortion High Value Multilayer Ceramic Capacitors(CF_LD)
●107TYPE
【Temperature Characteristic LD : X5R】　0.8mm thickness（A）
HTLT
Rated voltage x ％
UMK107BLD224[]A-T 50 X5R 0.22 μ ±10, ±20 10 150 0.8+0.20/-0 R
TMK107BLD474[]A-T X5R 0.47 μ ±10, ±20 10 150 0.8+0.20/-0 R
TMK107BLD105[]A-T X5R 1 μ ±10, ±20 10 150 0.8+0.20/-0 R
●212TYPE
【Temperature Characteristic LD : X5R】　1.25mm thickness（G）
HTLT
Rated voltage x ％
GMK212 LD105[]G-T X5R 1 μ ±10, ±20 10 150 1.25±0.10 R
GMK212BLD225[]G-T X5R 2.2 μ ±10, ±20 10 150 1.25+0.20/-0 R
●316TYPE
【Temperature Characteristic LD : X5R】　1.6mm thickness（L）
HTLT
Rated voltage x ％
UMK316 LD105[]L-T 50 X5R 1 μ ±10, ±20 10 150 1.6±0.20 R
GMK316BLD475[]L-T 35 X5R 4.7 μ ±10, ±20 10 150 1.6±0.30 R
TMK316BLD106[]L-T 25 X5R 10 μ ±10, ±20 10 150 1.6±0.30 R
●325TYPE
【Temperature Characteristic LD : X5R】　1.9mm thickness（N）
HTLT
Rated voltage x ％
UMK325 LD105[]N-T 50 X5R 1 μ ±10, ±20 10 200 1.9±0.20 R
【Temperature Characteristic LD : X5R】　2.5mm thickness（M）
HTLT
Rated voltage x ％
UMK325 LD475[]M-P 50 X5R 4.7 μ ±10, ±20 10 200 2.5±0.20 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
35
Standard Type
25
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
25
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
35
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
37
1
8
■PARTS NUMBER
Medium-High Voltage Multilayer Ceramic Capacitors
●105TYPE
【Temperature Characteristic B7 : X7R】　0.5mm thickness（V）
HTLT
Rated voltage x ％
HMK105 B7221[]V-F X7R 220 p ±10, ±20 2.5 200 0.5±0.05 R
HMK105 B7331[]V-F X7R 330 p ±10, ±20 2.5 200 0.5±0.05 R
HMK105 B7471[]V-F X7R 470 p ±10, ±20 2.5 200 0.5±0.05 R
HMK105 B7681[]V-F X7R 680 p ±10, ±20 2.5 200 0.5±0.05 R
HMK105 B7102[]V-F X7R 1000 p ±10, ±20 2.5 200 0.5±0.05 R
HMK105 B7152[]V-F X7R 1500 p ±10, ±20 2.5 200 0.5±0.05 R
HMK105 B7222[]V-F X7R 2200 p ±10, ±20 2.5 200 0.5±0.05 R
HMK105 B7332[]V-F X7R 3300 p ±10, ±20 2.5 200 0.5±0.05 R
HMK105 B7472[]V-F X7R 4700 p ±10, ±20 2.5 200 0.5±0.05 R
【Temperature Characteristic CG : CG/C0G】　0.5mm thickness（V）
HTLT
Rated voltage x ％
HMK105 CG080DV-F CG C0G 8 p ±0.5pF 560 200 0.5±0.05 R
HMK105 CG090DV-F CG C0G 9 p ±0.5pF 580 200 0.5±0.05 R
HMK105 CG100DV-F CG C0G 10 p ±0.5pF 600 200 0.5±0.05 R
HMK105 CG120JV-F CG C0G 12 p ±5％ 640 200 0.5±0.05 R
HMK105 CG150JV-F CG C0G 15 p ±5％ 700 200 0.5±0.05 R
HMK105 CG180JV-F CG C0G 18 p ±5％ 760 200 0.5±0.05 R
HMK105 CG220JV-F CG C0G 22 p ±5％ 840 200 0.5±0.05 R
HMK105 CG240JV-F CG C0G 24 p ±5％ 880 200 0.5±0.05 R
HMK105 CG270JV-F CG C0G 27 p ±5％ 940 200 0.5±0.05 R
HMK105 CG330JV-F CG C0G 33 p ±5％ 1000 200 0.5±0.05 R
HMK105 CG390JV-F CG C0G 39 p ±5％ 1000 200 0.5±0.05 R
HMK105 CG470JV-F CG C0G 47 p ±5％ 1000 200 0.5±0.05 R
HMK105 CG560JV-F CG C0G 56 p ±5％ 1000 200 0.5±0.05 R
HMK105 CG680JV-F CG C0G 68 p ±5％ 1000 200 0.5±0.05 R
HMK105 CG820JV-F CG C0G 82 p ±5％ 1000 200 0.5±0.05 R
HMK105 CG101JV-F CG C0G 100 p ±5％ 1000 200 0.5±0.05 R
●107TYPE
【Temperature Characteristic BJ : B/X5R】　0.8mm thickness（A）
HTLT
Rated voltage x ％
HMK107 BJ102[]A-T B X5R*1 1000 p ±10, ±20 3.5 200 0.8±0.10 R
HMK107 BJ152[]A-T B X5R*1 1500 p ±10, ±20 3.5 200 0.8±0.10 R
HMK107 BJ222[]A-T B X5R*1 2200 p ±10, ±20 3.5 200 0.8±0.10 R
HMK107 BJ332[]A-T B X5R*1 3300 p ±10, ±20 3.5 200 0.8±0.10 R
HMK107 BJ472[]A-T B X5R*1 4700 p ±10, ±20 3.5 200 0.8±0.10 R
HMK107 BJ682[]A-T B X5R*1 6800 p ±10, ±20 3.5 200 0.8±0.10 R
HMK107 BJ103[]A-T B X5R*1 0.01 μ ±10, ±20 3.5 200 0.8±0.10 R
HMK107 BJ153[]A-T B X5R*1 0.015 μ ±10, ±20 3.5 200 0.8±0.10 R
HMK107 BJ223[]A-T B X5R*1 0.022 μ ±10, ±20 3.5 200 0.8±0.10 R
HMK107 BJ333[]A-T B X5R*1 0.033 μ ±10, ±20 3.5 200 0.8±0.10 R
HMK107 BJ473[]A-T B X5R*1 0.047 μ ±10, ±20 3.5 200 0.8±0.10 R
HMK107 BJ104[]A-T B X5R*1 0.1 μ ±10, ±20 3.5 200 0.8±0.10 R
HMK107 BJ224[]A-TE B X5R*1 0.22 μ ±10, ±20 3.5 150 0.8±0.10 R
【Temperature Characteristic C7 : X7S 】　0.8mm thickness（A）
HTLT
Rated voltage x ％
HMK107 C7224[]A-TE 100 X7S 0.22 μ ±10, ±20 3.5 150 0.8±0.10 R
【Temperature Characteristic B7 : X7R 】　0.8mm thickness（A）
HTLT
Rated voltage x ％
HMK107 B7102[]A-T X7R 1000 p ±10, ±20 3.5 200 0.8±0.10 R
HMK107 B7152[]A-T X7R 1500 p ±10, ±20 3.5 200 0.8±0.10 R
HMK107 B7222[]A-T X7R 2200 p ±10, ±20 3.5 200 0.8±0.10 R
HMK107 B7332[]A-T X7R 3300 p ±10, ±20 3.5 200 0.8±0.10 R
HMK107 B7472[]A-T X7R 4700 p ±10, ±20 3.5 200 0.8±0.10 R
HMK107 B7682[]A-T X7R 6800 p ±10, ±20 3.5 200 0.8±0.10 R
HMK107 B7103[]A-T X7R 0.01 μ ±10, ±20 3.5 200 0.8±0.10 R
HMK107 B7153[]A-T X7R 0.015 μ ±10, ±20 3.5 200 0.8±0.10 R
HMK107 B7223[]A-T X7R 0.022 μ ±10, ±20 3.5 200 0.8±0.10 R
HMK107 B7333[]A-T X7R 0.033 μ ±10, ±20 3.5 200 0.8±0.10 R
HMK107 B7473[]A-T X7R 0.047 μ ±10, ±20 3.5 200 0.8±0.10 R
HMK107 B7104[]A-T X7R 0.1 μ ±10, ±20 3.5 200 0.8±0.10 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
100
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F] Capacitance tolerance
Q
(at 1MHz)
min
Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
100
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
100
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
100
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
38
1
8
■PARTS NUMBER
【Temperature Characteristic SD : Standard 】　0.8mm thickness（A）
HTLT
Rated voltage x ％
HMK107 SD101KA-T 100 p ±10 0.1 200 0.8±0.10 R
HMK107 SD121KA-T 120 p ±10 0.1 200 0.8±0.10 R
HMK107 SD151KA-T 150 p ±10 0.1 200 0.8±0.10 R
HMK107 SD181KA-T 180 p ±10 0.1 200 0.8±0.10 R
HMK107 SD221KA-T 220 p ±10 0.1 200 0.8±0.10 R
HMK107 SD271KA-T 270 p ±10 0.1 200 0.8±0.10 R
HMK107 SD331KA-T 330 p ±10 0.1 200 0.8±0.10 R
HMK107 SD391KA-T 390 p ±10 0.1 200 0.8±0.10 R
HMK107 SD471KA-T 470 p ±10 0.1 200 0.8±0.10 R
HMK107 SD561KA-T 560 p ±10 0.1 200 0.8±0.10 R
HMK107 SD681KA-T 680 p ±10 0.1 200 0.8±0.10 R
HMK107 SD821KA-T 820 p ±10 0.1 200 0.8±0.10 R
HMK107 SD102KA-T 1000 p ±10 0.1 200 0.8±0.10 R
●212TYPE
【Temperature Characteristic BJ : B/X5R】　1.25mm thickness（G）
HTLT
Rated voltage x ％
HMK212 BJ103[]G-T B X5R*1 0.01 μ ±10, ±20 3.5 200 1.25±0.10 R
HMK212 BJ153[]G-T B X5R*1 0.015 μ ±10, ±20 3.5 200 1.25±0.10 R
HMK212 BJ223[]G-T B X5R*1 0.022 μ ±10, ±20 3.5 200 1.25±0.10 R
HMK212 BJ333[]G-T B X5R*1 0.033 μ ±10, ±20 3.5 200 1.25±0.10 R
HMK212 BJ473[]G-T B X5R*1 0.047 μ ±10, ±20 3.5 200 1.25±0.10 R
HMK212 BJ683[]G-T B X5R*1 0.068 μ ±10, ±20 3.5 200 1.25±0.10 R
HMK212 BJ104[]G-T B X5R*1 0.1 μ ±10, ±20 3.5 200 1.25±0.10 R
HMK212 BJ224[]G-T B X5R*1 0.22 μ ±10, ±20 3.5 200 1.25±0.10 R
HMK212 BJ474[]G-TE B X5R*1 0.47 μ ±10, ±20 3.5 150 1.25±0.10 R
HMK212BBJ105[]G-TE B X5R*1 1 μ ±10, ±20 3.5 150 1.25+0.20/-0 R
QMK212 BJ472[]G-T B X5R*1 4700 p ±10, ±20 2.5 150 1.25±0.10 R
QMK212 BJ682[]G-T B X5R*1 6800 p ±10, ±20 2.5 150 1.25±0.10 R
QMK212 BJ103[]G-T B X5R*1 0.01 μ ±10, ±20 2.5 150 1.25±0.10 R
QMK212 BJ153[]G-T B X5R*1 0.015 μ ±10, ±20 2.5 150 1.25±0.10 R
QMK212 BJ223[]G-T B X5R*1 0.022 μ ±10, ±20 2.5 150 1.25±0.10 R
【Temperature Characteristic BJ : B/X5R】　0.85mm thickness（D）
HTLT
Rated voltage x ％
QMK212 BJ102[]D-T B X5R*1 1000 p ±10, ±20 2.5 150 0.85±0.10 R
QMK212 BJ152[]D-T B X5R*1 1500 p ±10, ±20 2.5 150 0.85±0.10 R
QMK212 BJ222[]D-T B X5R*1 2200 p ±10, ±20 2.5 150 0.85±0.10 R
QMK212 BJ332[]D-T B X5R*1 3300 p ±10, ±20 2.5 150 0.85±0.10 R
【Temperature Characteristic C7 : X7S】　1.25mm thickness（G）
HTLT
Rated voltage x ％
HMK212 C7474[]G-TE 100 X7S 0.47 μ ±10, ±20 3.5 150 1.25±0.10 R
HMK212BC7105[]G-TE 100 X7S 1 μ ±10, ±20 3.5 150 1.25+0.20/-0 R
【Temperature Characteristic B7 : X7R】　1.25mm thickness（G）
HTLT
Rated voltage x ％
HMK212 B7103[]G-T X7R 0.01 μ ±10, ±20 3.5 200 1.25±0.10 R
HMK212 B7153[]G-T X7R 0.015 μ ±10, ±20 3.5 200 1.25±0.10 R
HMK212 B7223[]G-T X7R 0.022 μ ±10, ±20 3.5 200 1.25±0.10 R
HMK212 B7333[]G-T X7R 0.033 μ ±10, ±20 3.5 200 1.25±0.10 R
HMK212 B7473[]G-T X7R 0.047 μ ±10, ±20 3.5 200 1.25±0.10 R
HMK212 B7683[]G-T X7R 0.068 μ ±10, ±20 3.5 200 1.25±0.10 R
HMK212 B7104[]G-T X7R 0.1 μ ±10, ±20 3.5 200 1.25±0.10 R
HMK212 B7224[]G-T X7R 0.22 μ ±10, ±20 3.5 200 1.25±0.10 R
QMK212 B7472[]G-T X7R 4700 p ±10, ±20 2.5 150 1.25±0.10 R
QMK212 B7682[]G-T X7R 6800 p ±10, ±20 2.5 150 1.25±0.10 R
QMK212 B7103[]G-T X7R 0.01 μ ±10, ±20 2.5 150 1.25±0.10 R
QMK212 B7153[]G-T X7R 0.015 μ ±10, ±20 2.5 150 1.25±0.10 R
QMK212 B7223[]G-T X7R 0.022 μ ±10, ±20 2.5 150 1.25±0.10 R
【Temperature Characteristic B7 : X7R】　0.85mm thickness（D）
HTLT
Rated voltage x ％
QMK212 B7102[]D-T X7R 1000 p ±10, ±20 2.5 150 0.85±0.10 R
QMK212 B7152[]D-T X7R 1500 p ±10, ±20 2.5 150 0.85±0.10 R
QMK212 B7222[]D-T X7R 2200 p ±10, ±20 2.5 150 0.85±0.10 R
QMK212 B7332[]D-T X7R 3300 p ±10, ±20 2.5 150 0.85±0.10 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
100 Standard Type
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
100
250
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
250
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
100
250
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
250
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
39
1
8
■PARTS NUMBER
【Temperature Characteristic SD : Standard 】　0.85mm thickness（D）
HTLT
Rated voltage x ％
HMK212 SD222KD-T 2200 p ±10 0.1 200 0.85±0.10 R
HMK212 SD472KD-T 4700 p ±10 0.1 200 0.85±0.10 R
QMK212 SD101KD-T 100 p ±10 0.1 150 0.85±0.10 R
QMK212 SD121KD-T 120 p ±10 0.1 150 0.85±0.10 R
QMK212 SD151KD-T 150 p ±10 0.1 150 0.85±0.10 R
QMK212 SD181KD-T 180 p ±10 0.1 150 0.85±0.10 R
QMK212 SD221KD-T 220 p ±10 0.1 150 0.85±0.10 R
QMK212 SD331KD-T 330 p ±10 0.1 150 0.85±0.10 R
QMK212 SD391KD-T 390 p ±10 0.1 150 0.85±0.10 R
QMK212 SD471KD-T 470 p ±10 0.1 150 0.85±0.10 R
QMK212 SD561KD-T 560 p ±10 0.1 150 0.85±0.10 R
QMK212 SD681KD-T 680 p ±10 0.1 150 0.85±0.10 R
QMK212 SD821KD-T 820 p ±10 0.1 150 0.85±0.10 R
QMK212 SD102KD-T 1000 p ±10 0.1 150 0.85±0.10 R
【Temperature Characteristic SD : Standard 】　1.25mm thickness（G）
HTLT
Rated voltage x ％
HMK212 SD392KG-T 100 3900 p ±10 0.1 200 1.25±0.10 R
●316TYPE
【Temperature Characteristic BJ : B/X5R】　1.6mm thickness（L）
HTLT
Rated voltage x ％
HMK316 BJ473[]L-T B X5R*1 0.047 μ ±10, ±20 3.5 200 1.6±0.20 R
HMK316 BJ683[]L-T B X5R*1 0.068 μ ±10, ±20 3.5 200 1.6±0.20 R
HMK316 BJ104[]L-T B X5R*1 0.1 μ ±10, ±20 3.5 200 1.6±0.20 R
HMK316 BJ154[]L-T B X5R*1 0.15 μ ±10, ±20 3.5 200 1.6±0.20 R
HMK316 BJ224[]L-T B X5R*1 0.22 μ ±10, ±20 3.5 200 1.6±0.20 R
HMK316 BJ334[]L-T B X5R*1 0.33 μ ±10, ±20 3.5 200 1.6±0.20 R
HMK316 BJ474[]L-T B X5R*1 0.47 μ ±10, ±20 3.5 200 1.6±0.20 R
HMK316 BJ105[]L-T B X5R*1 1 μ ±10, ±20 3.5 200 1.6±0.20 R
HMK316ABJ225[]L-TE B X5R*1 2.2 μ ±10, ±20 3.5 150 1.6±0.20 R
QMK316 BJ333[]L-T B X5R*1 0.033 μ ±10, ±20 2.5 150 1.6±0.20 R
QMK316 BJ473[]L-T B X5R*1 0.047 μ ±10, ±20 2.5 150 1.6±0.20 R
QMK316 BJ683[]L-T B X5R*1 0.068 μ ±10, ±20 2.5 150 1.6±0.20 R
QMK316 BJ104[]L-T B X5R*1 0.1 μ ±10, ±20 2.5 150 1.6±0.20 R
SMK316 BJ153[]L-T B X5R*1 0.015 μ ±10, ±20 2.5 120 1.6±0.20 R
SMK316 BJ223[]L-T B X5R*1 0.022 μ ±10, ±20 2.5 120 1.6±0.20 R
【Temperature Characteristic BJ : B/X5R】　1.15mm thickness（F）
HTLT
Rated voltage x ％
SMK316 BJ102[]F-T B X5R*1 1000 p ±10, ±20 2.5 120 1.15±0.10 R
SMK316 BJ152[]F-T B X5R*1 1500 p ±10, ±20 2.5 120 1.15±0.10 R
SMK316 BJ222[]F-T B X5R*1 2200 p ±10, ±20 2.5 120 1.15±0.10 R
SMK316 BJ332[]F-T B X5R*1 3300 p ±10, ±20 2.5 120 1.15±0.10 R
SMK316 BJ472[]F-T B X5R*1 4700 p ±10, ±20 2.5 120 1.15±0.10 R
SMK316 BJ682[]F-T B X5R*1 6800 p ±10, ±20 2.5 120 1.15±0.10 R
SMK316 BJ103[]F-T B X5R*1 0.01 μ ±10, ±20 2.5 120 1.15±0.10 R
【Temperature Characteristic C7 : X7S】　1.6mm thickness（L）
HTLT
Rated voltage x ％
HMK316AC7225[]L-TE 100 X7S 2.2 μ ±10, ±20 3.5 150 1.6±0.20 R
【Temperature Characteristic B7 : X7R】　1.6mm thickness（L）
HTLT
Rated voltage x ％
HMK316 B7473[]L-T X7R 0.047 μ ±10, ±20 3.5 200 1.6±0.20 R
HMK316 B7683[]L-T X7R 0.068 μ ±10, ±20 3.5 200 1.6±0.20 R
HMK316 B7104[]L-T X7R 0.1 μ ±10, ±20 3.5 200 1.6±0.20 R
HMK316 B7154[]L-T X7R 0.15 μ ±10, ±20 3.5 200 1.6±0.20 R
HMK316 B7224[]L-T X7R 0.22 μ ±10, ±20 3.5 200 1.6±0.20 R
HMK316 B7334[]L-T X7R 0.33 μ ±10, ±20 3.5 200 1.6±0.20 R
HMK316 B7474[]L-T X7R 0.47 μ ±10, ±20 3.5 200 1.6±0.20 R
HMK316 B7105[]L-T X7R 1 μ ±10, ±20 3.5 200 1.6±0.20 R
QMK316 B7333[]L-T X7R 0.033 μ ±10, ±20 2.5 150 1.6±0.20 R
QMK316 B7473[]L-T X7R 0.047 μ ±10, ±20 2.5 150 1.6±0.20 R
QMK316 B7683[]L-T X7R 0.068 μ ±10, ±20 2.5 150 1.6±0.20 R
QMK316 B7104[]L-T X7R 0.1 μ ±10, ±20 2.5 150 1.6±0.20 R
SMK316 B7153[]L-T X7R 0.015 μ ±10, ±20 2.5 120 1.6±0.20 R
SMK316 B7223[]L-T X7R 0.022 μ ±10, ±20 2.5 120 1.6±0.20 R
SMK316AB7333[]L-T X7R 0.033 μ ±10, ±20 2.5 120 1.6±0.20 R
SMK316AB7473[]L-T X7R 0.047 μ ±10, ±20 2.5 120 1.6±0.20 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
100
Standard Type
250
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Standard Type
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
100
250
630
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
630
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
100
250
630
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
40
1
8
■PARTS NUMBER
【Temperature Characteristic B7 : X7R】　1.15mm thickness（F）
HTLT
Rated voltage x ％
SMK316 B7102[]F-T X7R 1000 p ±10, ±20 2.5 120 1.15±0.10 R
SMK316 B7152[]F-T X7R 1500 p ±10, ±20 2.5 120 1.15±0.10 R
SMK316 B7222[]F-T X7R 2200 p ±10, ±20 2.5 120 1.15±0.10 R
SMK316 B7332[]F-T X7R 3300 p ±10, ±20 2.5 120 1.15±0.10 R
SMK316 B7472[]F-T X7R 4700 p ±10, ±20 2.5 120 1.15±0.10 R
SMK316 B7682[]F-T X7R 6800 p ±10, ±20 2.5 120 1.15±0.10 R
SMK316 B7103[]F-T X7R 0.01 μ ±10, ±20 2.5 120 1.15±0.10 R
【Temperature Characteristic SD : Standard 】　1.6mm thickness（L）
HTLT
Rated voltage x ％
HMK316 SD223KL-T 100 0.022 μ ±10 0.1 200 1.6±0.20 R
QMK316 SD103KL-T 250 0.01 μ ±10 0.1 150 1.6±0.20 R
●325TYPE
【Temperature Characteristic BJ : B/X5R】　2.5mm thickness（M）
HTLT
Rated voltage x ％
HMK325 BJ225[]M-P 100 B X5R*1 2.2 μ ±10, ±20 3.5 200 2.5±0.20 R
HMK325 BJ475[]M-PE 100 B X5R*1 4.7 μ ±10, ±20 3.5 150 2.5±0.20 R
【Temperature Characteristic BJ : B/X5R】　1.9mm thickness（N）
HTLT
Rated voltage x ％
HMK325 BJ154[]N-T B X5R*1 0.15 μ ±10, ±20 3.5 200 1.9±0.20 R
HMK325 BJ224[]N-T B X5R*1 0.22 μ ±10, ±20 3.5 200 1.9±0.20 R
HMK325 BJ334[]N-T B X5R*1 0.33 μ ±10, ±20 3.5 200 1.9±0.20 R
HMK325 BJ474[]N-T B X5R*1 0.47 μ ±10, ±20 3.5 200 1.9±0.20 R
HMK325 BJ684[]N-T B X5R*1 0.68 μ ±10, ±20 3.5 200 1.9±0.20 R
HMK325 BJ105[]N-T B X5R*1 1 μ ±10, ±20 3.5 200 1.9±0.20 R
HMK325 BJ475[]N-TE B X5R*1 4.7 μ ±10, ±20 3.5 150 1.9±0.20 R
QMK325 BJ473[]N-T B X5R*1 0.047 μ ±10, ±20 2.5 150 1.9±0.20 R
QMK325 BJ104[]N-T B X5R*1 0.1 μ ±10, ±20 2.5 150 1.9±0.20 R
QMK325 BJ154[]N-T B X5R*1 0.15 μ ±10, ±20 2.5 150 1.9±0.20 R
QMK325 BJ224[]N-T B X5R*1 0.22 μ ±10, ±20 2.5 150 1.9±0.20 R
SMK325 BJ223[]N-T B X5R*1 0.022 μ ±10, ±20 2.5 120 1.9±0.20 R
SMK325 BJ333[]N-T B X5R*1 0.033 μ ±10, ±20 2.5 120 1.9±0.20 R
SMK325 BJ473[]N-T B X5R*1 0.047 μ ±10, ±20 2.5 120 1.9±0.20 R
【Temperature Characteristic BJ : B/X5R】　1.15mm thickness（F）
HTLT
Rated voltage x ％
HMK325 BJ104[]F-T 100 B X5R*1 0.1 μ ±10, ±20 3.5 200 1.15±0.10 R
【Temperature Characteristic B7 : X7R】　2.5mm thickness（M）
HTLT
Rated voltage x ％
HMK325 B7225[]M-P 100 X7R 2.2 μ ±10, ±20 3.5 200 2.5±0.20 R
【Temperature Characteristic B7 : X7R】　1.9mm thickness（N）
HTLT
Rated voltage x ％
HMK325 B7154[]N-T X7R 0.15 μ ±10, ±20 3.5 200 1.9±0.20 R
HMK325 B7224[]N-T X7R 0.22 μ ±10, ±20 3.5 200 1.9±0.20 R
HMK325 B7334[]N-T X7R 0.33 μ ±10, ±20 3.5 200 1.9±0.20 R
HMK325 B7474[]N-T X7R 0.47 μ ±10, ±20 3.5 200 1.9±0.20 R
HMK325 B7684[]N-T X7R 0.68 μ ±10, ±20 3.5 200 1.9±0.20 R
HMK325 B7105[]N-T X7R 1 μ ±10, ±20 3.5 200 1.9±0.20 R
QMK325 B7473[]N-T X7R 0.047 μ ±10, ±20 2.5 150 1.9±0.20 R
QMK325 B7104[]N-T X7R 0.1 μ ±10, ±20 2.5 150 1.9±0.20 R
QMK325 B7154[]N-T X7R 0.15 μ ±10, ±20 2.5 150 1.9±0.20 R
QMK325 B7224[]N-T X7R 0.22 μ ±10, ±20 2.5 150 1.9±0.20 R
SMK325 B7223[]N-T X7R 0.022 μ ±10, ±20 2.5 120 1.9±0.20 R
SMK325 B7333[]N-T X7R 0.033 μ ±10, ±20 2.5 120 1.9±0.20 R
SMK325 B7473[]N-T X7R 0.047 μ ±10, ±20 2.5 120 1.9±0.20 R
【Temperature Characteristic C7 : X7S】　2.5mm thickness（M）
HTLT
Rated voltage x ％
HMK325 C7475[]M-PE 100 X7S 4.7 μ ±10, ±20 3.5 150 2.5±0.20 R
【Temperature Characteristic C7 : X7S】　1.9mm thickness（N）
HTLT
Rated voltage x ％
HMK325 C7475[]N-TE 100 X7S 4.7 μ ±10, ±20 3.5 150 1.9±0.20 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
630
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Standard Type
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
100
250
630
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
100
250
630
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
41
1
8
■PARTS NUMBER
【Temperature Characteristic B7 : X7R】　1.15mm thickness（F）
HTLT
Rated voltage x ％
HMK325 B7104[]F-T 100 X7R 0.1 μ ±10, ±20 3.5 200 1.15±0.10 R
●432TYPE
【Temperature Characteristic BJ : B/X5R】 2.5mm thickness（M）
HTLT
Rated voltage x ％
HMK432 BJ474[]M-T B X5R*1 0.47 μ ±10, ±20 3.5 200 2.5±0.20 R
HMK432 BJ105[]M-T B X5R*1 1 μ ±10, ±20 3.5 200 2.5±0.20 R
HMK432 BJ155[]M-T B X5R*1 1.5 μ ±10, ±20 3.5 200 2.5±0.20 R
HMK432 BJ225[]M-T B X5R*1 2.2 μ ±10, ±20 3.5 200 2.5±0.20 R
QMK432 BJ104[]M-T B X5R*1 0.1 μ ±10, ±20 2.5 150 2.5±0.20 R
QMK432 BJ224[]M-T B X5R*1 0.22 μ ±10, ±20 2.5 150 2.5±0.20 R
QMK432 BJ334[]M-T B X5R*1 0.33 μ ±10, ±20 2.5 150 2.5±0.20 R
QMK432 BJ474[]M-T B X5R*1 0.47 μ ±10, ±20 2.5 150 2.5±0.20 R
SMK432 BJ473[]M-T B X5R*1 0.047 μ ±10, ±20 2.5 120 2.5±0.20 R
SMK432 BJ683[]M-T B X5R*1 0.068 μ ±10, ±20 2.5 120 2.5±0.20 R
SMK432 BJ104[]M-T B X5R*1 0.1 μ ±10, ±20 2.5 120 2.5±0.20 R
【Temperature Characteristic B7 : X7R】 2.5mm thickness（M）
HTLT
Rated voltage x ％
HMK432 B7474[]M-T X7R 0.47 μ ±10, ±20 3.5 200 2.5±0.20 R
HMK432 B7105[]M-T X7R 1 μ ±10, ±20 3.5 200 2.5±0.20 R
HMK432 B7155[]M-T X7R 1.5 μ ±10, ±20 3.5 200 2.5±0.20 R
HMK432 B7225[]M-T X7R 2.2 μ ±10, ±20 3.5 200 2.5±0.20 R
QMK432 B7104[]M-T X7R 0.1 μ ±10, ±20 2.5 150 2.5±0.20 R
QMK432 B7224[]M-T X7R 0.22 μ ±10, ±20 2.5 150 2.5±0.20 R
QMK432 B7334[]M-T X7R 0.33 μ ±10, ±20 2.5 150 2.5±0.20 R
QMK432 B7474[]M-T X7R 0.47 μ ±10, ±20 2.5 150 2.5±0.20 R
SMK432 B7473[]M-T X7R 0.047 μ ±10, ±20 2.5 120 2.5±0.20 R
SMK432 B7683[]M-T X7R 0.068 μ ±10, ±20 2.5 120 2.5±0.20 R
SMK432 B7104[]M-T X7R 0.1 μ ±10, ±20 2.5 120 2.5±0.20 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
100
250
630
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
100
250
630
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
42
1
8
■PARTS NUMBER
LW Reversal Decoupling Capacitors（LWDCTM）
●105TYPE
【Temperature Characteristic BJ : X5R】 0.3mm thickness（P）
HTLT
Rated voltage x ％
TWK105 BJ104MP-F 25 X5R 0.1 μ ±20 5 150 0.3±0.05 R
EWK105 BJ224MP-F 16 X5R 0.22 μ ±20 10 150 0.3±0.05 R
LWK105 BJ474MP-F 10 X5R 0.47 μ ±20 10 150 0.3±0.05 R
JWK105 BJ104MP-F X5R*1 0.1 μ ±20 5 150 0.3±0.05 R
JWK105 BJ474MP-F X5R*1 0.47 μ ±20 10 150 0.3±0.05 R
JWK105 BJ105MP-F X5R 1 μ ±20 10 150 0.3±0.05 R
JWK105 BJ225MP-F X5R 2.2 μ ±20 10 150 0.3±0.05 R
【Temperature Characteristic C6 : X6S , C7 : X7S】 0.3mm thickness（P）
HTLT
Rated voltage x ％
EWK105 C6104MP-F 16 X6S 0.1 μ ±20 5 150 0.3±0.05 R
LWK105 C7104MP-F X7S 0.1 μ ±20 5 150 0.3±0.05 R
LWK105 C6224MP-F X6S 0.22 μ ±20 10 150 0.3±0.05 R
JWK105 C7104MP-F X7S 0.1 μ ±20 5 150 0.3±0.05 R
JWK105 C7224MP-F X7S 0.22 μ ±20 10 150 0.3±0.05 R
JWK105 C6474MP-F X6S 0.47 μ ±20 10 150 0.3±0.05 R
AWK105 C6224MP-F X6S 0.22 μ ±20 10 150 0.3±0.05 R
AWK105 C6474MP-F X6S 0.47 μ ±20 10 150 0.3±0.05 R
AWK105 C6105MP-F X6S 1 μ ±20 10 150 0.3±0.05 R
AWK105 C6225MP-F X6S 2.2 μ ±20 10 150 0.3±0.05 R
●107TYPE
【Temperature Characteristic BJ : X5R】 0.5mm thickness（V）
HTLT
Rated voltage x ％
TWK107 BJ104MV-T 25 X5R*1 0.1 μ ±20 5 150 0.5±0.05 R
EWK107 BJ224MV-T X5R*1 0.22 μ ±20 5 150 0.5±0.05 R
EWK107 BJ474MV-T X5R*1 0.47 μ ±20 5 150 0.5±0.05 R
LWK107 BJ105MV-T X5R 1 μ ±20 10 150 0.5±0.05 R
LWK107 BJ225MV-T X5R 2.2 μ ±20 10 150 0.5±0.05 R
JWK107 BJ105MV-T X5R*1 1 μ ±20 10 150 0.5±0.05 R
JWK107 BJ225MV-T X5R 2.2 μ ±20 10 150 0.5±0.05 R
JWK107 BJ475MV-T X5R 4.7 μ ±20 10 150 0.5±0.05 R
AWK107 BJ106MV-T 4 X5R 10 μ ±20 10 150 0.5±0.05 R
【Temperature Characteristic B7 : X7R , C6 : X6S , C7 : X7S】 0.5mm thickness（V）
HTLT
Rated voltage x ％
TWK107 B7104MV-T 25 X7R 0.1 μ ±20 5 150 0.5±0.05 R
EWK107 B7224MV-T X7R 0.22 μ ±20 5 150 0.5±0.05 R
EWK107 B7474MV-T X7R 0.47 μ ±20 5 150 0.5±0.05 R
JWK107 C7105MV-T 6.3 X7S 1 μ ±20 10 150 0.5±0.05 R
AWK107 C7225MV-T X7S 2.2 μ ±20 10 150 0.5±0.05 R
AWK107 C6475MV-T X6S 4.7 μ ±20 10 150 0.5±0.05 R
PWK107 C6106MV-T 2.5 X6S 10 μ ±20 10 150 0.5±0.05 R
●212TYPE
【Temperature Characteristic BJ : X5R】 0.85mm thickness（D）
HTLT
Rated voltage x ％
TWK212 BJ475[]D-T 25 X5R 4.7 μ ±10, ±20 10 150 0.85±0.10 R
EWK212 BJ106MD-T 16 X5R 10 μ ±20 10 150 0.85±0.10 R
LWK212 BJ475[]D-T X5R 4.7 μ ±10, ±20 10 150 0.85±0.10 R
LWK212 BJ106MD-T X5R 10 μ ±20 10 150 0.85±0.10 R
JWK212 BJ226MD-T 6.3 X5R 22 μ ±20 10 150 0.85±0.10 R
【Temperature Characteristic B7 : X7R , C6 : X6S】 0.85mm thickness（D）
HTLT
Rated voltage x ％
TWK212 B7225[]D-T 25 X7R 2.2 μ ±10, ±20 5 150 0.85±0.10 R
EWK212 C6475[]D-T 16 X6S 4.7 μ ±10, ±20 10 150 0.85±0.10 R
LWK212 C6106MD-T 10 X6S 10 μ ±20 10 150 0.85±0.10 R
AWK212 C6226MD-T 4 X6S 22 μ ±20 10 150 0.85±0.10 R
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
6.3
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
10
6.3
4
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
16
10
6.3
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
16
4
Capacitance tolerance
[％]
Part number 1 Part number 2 Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
Capacitance tolerance
[％]
10
Part number 1 Part number 2
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
tanδ
[％] Thickness*3 [mm]
Soldering
R:Reflow
W:Wave
c_mlcc_e-E06R01
CERAMIC CAPACITORS
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
43
1
8
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_pack_e-E06R01
Multilayer Ceramic Capacitors
■PACKAGING
①Minimum Quantity
●Taped package
Type(EIA) Thickness Standard quantity [pcs]
mm code Paper tape Embossed tape
□MK021(008004) 0.125 K － 50000
□VS021(008004)
□MK042(01005) 0.2 C, D － 40000
□VS042(01005) 0.2 C
□MK063(0201) 0.3 P,T 15000 －
□WK105(0204) ※ 0.3 P 10000 －
□MK105(0402)
□MF105(0402)
0.13 H － 20000
0.18 E － 15000
0.2 C 20000 －
0.3 P 15000 －
0.5 V 10000 －
□VK105(0402) 0.5 W 10000 －
□MK107(0603)
□WK107(0306) ※
□MF107(0603)
0.45 K 4000 －
0.5 V － 4000
0.8 A 4000 －
□VS107(0603) 0.7 C 4000 －
□MJ107(0603) 0.8 A 3000 3000
□MK212(0805)
□WK212(0508) ※
□MF212(0805)
0.45 K 4000 －
0.85 D
1.25 G － 3000
□VS212(0805) 0.85 D 4000 －
□MJ212(0805) 0.85 D 4000 －
1.25 G － 2000
□MK316(1206)
□MF316(1206)
0.85 D 4000 －
1.15 F － 3000
1.6 L － 2000
□MJ316(1206) 1.15 F － 3000
1.6 L － 2000
□MK325(1210)
□MF325(1210)
0.85 D
－ 2000
1.15 F
1.9 N
2.0max. Y
2.5 M － 1000
□MJ325(1210) 1.9 N － 2000
2.5 M － 500(T), 1000(P)
□MK432(1812) 2.5 M － 500
Note : ※ LW Reverse type.
②Taping material
※No bottom tape for pressed carrier tape
●Card board carrier tape
Top tape
Base tape
Sprocket hole
Bottom tape Chip cavity
●Embossed tape
Top tape
Base tape
Sprocket hole
Chip cavity
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_pack_e-E06R01
Chip filled
Chip
※ LW Reverse type.
③Representative taping dimensions
●Paper Tape（8mm wide）
●Pressed carrier tape（ 2mm pitch） Unit：mm（inch）
F2.0±0.05
(0.079±0.002)
4.0±0.1
(0.157±0.004)
1.75
±
0.1
(0.069±0.004）
3.5±0.05
(0.138±0.002)
8.0±0.3
(0.315±0.012)
φ1.5＋0.1/－0
(φ0.059＋0.004/-0)
Sprocket hole
A
B
T
T1
Type(EIA) Chip Cavity Insertion Pitch Tape Thickness
Ａ Ｂ Ｆ Ｔ T1
□MK063(0201) 0.37 0.67
2.0±0.05
0.45max. 0.42max.
□WK105(0204) ※
0.65 1.15
□MK105(0402) （*1 C） 0.4max. 0.3max.
□MK105(0402) （*1 P） 0.45max. 0.42max.
Note *1 Thickness, C：0.2mm ,P：0.3mm. ※ LW Reverse type. Unit：mm
●Punched carrier tape （2mm pitch） Unit：mm（inch）
F2.0±0.05
(0.079±0.002)
4.0±0.1
(0.157±0.004)
1.75
±
0.1
(0.069±0.004）
3.5±0.05
(0.138±0.002)
8.0±0.3
(0.315±0.012)
φ1.5＋0.1/－0
(φ0.059＋0.004/-0)
Sprocket hole
A
B
T
Type(EIA) Chip Cavity Insertion Pitch Tape Thickness
Ａ Ｂ Ｆ Ｔ
□MK105 (0402)
□MF105 (0402)
□VK105 (0402)
0.65 1.15 2.0±0.05 0.8max.
Unit：mm
●Punched carrier tape （4mm pitch） Unit：mm（inch）
F
2.0±0.1
(0.079±0.004)
4.0±0.1
(0.157±0.004)
1.75
±
0.1
(0.069±0.004）
3.5±0.05
(0.138±0.002)
8.0±0.3
(0.315±0.012)
φ1.5＋0.1/－0
(φ0.059＋0.004/-0)
Sprocket hole
A
B
T
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_pack_e-E06R01
Type(EIA) Chip Cavity Insertion Pitch Tape Thickness
Ａ Ｂ Ｆ Ｔ
□MK107(0603)
□WK107(0306) ※
□MF107(0603)
1.0 1.8
4.0±0.1
1.1max.
□MK212(0805)
□WK212(0508) ※ 1.65 2.4 1.1max.
□MK316(1206) 2.0 3.6
Note：Taping size might be different depending on the size of the product. ※ LW Reverse type. Unit：mm
●Embossed tape（4mm wide） Unit：mm（inch）
F1.0±0.02
(
0.039
±
0.001)
2.0±0.04
(
0.079
±
0.002)
0.9
±
0.05
(0.035±0.002)
1.8±0.02
(0.071±0.001)
4.0±0.05
(0.157±0.002)
φ0.8±0.04
(φ0.031±0.002)
Sprocket hole
A
B
Type(EIA) Chip Cavity Insertion Pitch Tape Thickness
Ａ Ｂ Ｆ K T
□MK021(008004) 0.135 0.27
1.0±0.02 0.5max. 0.25max.
□VS021(008004)
□MK042(01005) 0.23 0.43
□VS042(01005)
Unit：mm
●Embossed tape（8mm wide） Unit：mm（inch）
F
2.0±0.1
(0.079±0.004)
4.0±0.1
(0.157±0.004)
1.75±0.1
(0.069±0.004）
3.5±0.05
(0.138±0.002)
8.0±0.3
(0.315±0.012)
φ1.5＋0.1/－0
(φ0.059＋0.004/-0)
Sprocket hole
A
B
Type(EIA) Chip Cavity Insertion Pitch Tape Thickness
Ａ Ｂ Ｆ K T
□MK105(0402) 0.6 1.1 2.0±0.1 0.6max 0.2±0.1
□WK107(0306) ※ 1.0 1.8
4.0±0.1
1.3max. 0.25±0.1
□MK212(0805)
□MF212(0805) 1.65 2.4
3.4max. 0.6max.
□MK316(1206)
□MF316(1206) 2.0 3.6
□MK325(1210)
□MF325(1210) 2.8 3.6
Note： ※ LW Reverse type. Unit：mm
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_pack_e-E06R01
●Embossed tape（12mm wide） Unit：mm（inch）
F
2.0±0.1
(0.079±0.004)
4.0±0.1
(0.157±0.004)
1.75±0.1
(0.069±0.004）
5.5±0.05
(0.217±0.002)
12.0±0.3
(0.472±0.012)
φ1.5＋0.1/－0
(φ0.059＋0.004/-0)
Sprocket hole
A
B
Type(EIA) Chip Cavity Insertion Pitch Tape Thickness
Ａ Ｂ Ｆ K T
□MK325(1210) 3.1 4.0 8.0±0.1 4.0max. 0.6max.
□MK432(1812) 3.7 4.9 8.0±0.1 4.0max. 0.6max.
Unit：mm
④Trailer and Leader
Blank portion Chip cavity Blank portion Leader
160mm or more
(6.3inches or more)
Direction of tape feed
100mm or more
(3.94inches or more)
400mm or more
(15.7inches or more)
⑤Reel size
E
C
D
R B
t
A
W
A B C D E R
φ178±2.0 φ50min. φ13.0±0.2 φ21.0±0.8 2.0±0.5 1.0
T W
4mm wide tape 1.5max. 5±1.0
8mm wide tape 2.5max. 10±1.5
12mm wide tape 2.5max. 14±1.5 Unit：mm
⑥Top Tape Strength
The top tape requires a peel-off force of 0.1 to 0.7N in the direction of the arrow as illustrated below.
0～20° Top tape
Base tape
Pull direction
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_reli_e-E06R01
Super Low Distortion Multilayer Ceramic Capacitors , Medium-High Voltage Multilayer Ceramic Capacitors and
High Reliability Application Multilayer Ceramic Capacitors are noted separately.
Multilayer Ceramic Capacitors
■RELIABILITY DATA
1.Operating Temperature Range
Specified
Value
Temperature
Compensating（Class1）
Standard －55 to ＋125℃
High Frequency Type
High Permittivity （Class2）
Specification Temperature Range
BJ B －25 to ＋85℃
X5R －55 to ＋85℃
B7 X7R －55 to ＋125℃
C6 X6S －55 to ＋105℃
C7 X7S －55 to ＋125℃
LD(※) X5R －55 to ＋85℃
Note: ※LD Low distortion high value multilayer ceramic capacitor
2. Storage Conditions
Specified
Value
Temperature
Compensating（Class1）
Standard －55 to ＋125℃
High Frequency Type
High Permittivity （Class2）
Specification Temperature Range
BJ B －25 to ＋85℃
X5R －55 to ＋85℃
B7 X7R －55 to ＋125℃
C6 X6S －55 to ＋105℃
C7 X7S －55 to ＋125℃
LD(※) X5R －55 to ＋85℃
Note: ※LD Low distortion high value multilayer ceramic capacitor
3. Rated Voltage
Specified
Value
Temperature
Compensating（Class1）
Standard 50VDC, 25VDC, 16VDC
High Frequency Type 50VDC, 25VDC, 16VDC
High Permittivity （Class2） 50VDC, 35VDC, 25VDC, 16VDC, 10VDC, 6.3VDC, 4VDC, 2.5VDC
4. Withstanding Voltage （Between terminals）
Specified
Value
Temperature
Compensating（Class1）
Standard
No breakdown or damage
High Frequency Type
High Permittivity （Class2）
Test
Methods and
Remarks
Class 1 Class 2
Applied voltage Rated voltage×3 Rated voltage×2.5
Duration 1 to 5 sec.
Charge/discharge current 50mA max.
5. Insulation Resistance
Specified
Value
Temperature
Compensating（Class1）
Standard 10000 MΩ min.
High Frequency Type
High Permittivity （Class2） Note 1 C≦0.047μF : 10000 MΩ min.
C＞0.047μF : 500MΩ・μF
Test
Methods and
Remarks
Applied voltage : Rated voltage
Duration : 60±5 sec.
Charge/discharge current : 50mA max.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_reli_e-E06R01
6. Capacitance （Tolerance）
Specified
Value
Temperature
Compensating（Class1）
Standard
C□
U□
SL
0.2pF≦C≦5pF : ±0.25pF
0.2pF≦C≦10pF : ±0.5pF
C＞10pF : ±5% or ±10%
High Frequency Type CG 0.2pF≦C≦2pF : ±0.1pF
C＞2pF : ±5%
High Permittivity （Class2） ±10% or ±20%
Test
Methods and
Remarks
Class 1 Class 2
Standard High Frequency Type C≦10μF C＞10μF
Preconditioning None Thermal treatment （at 150℃ for 1hr） Note 2
Measuring frequency 1ＭHz±10% 1kHz±10% 120±10Hz
Measuring voltage Nte 0.5 to 5Vrms 1±0.2Vrms 0.5±0.1Vrms
Bias application None
7. Q or Dissipation Factor
Specified
Value
Temperature
Compensating（Class1）
Standard C＜30pF : Q≧400＋20C
C≧30pF : Q≧1000 （C：Nominal capacitance）
High Frequency Type Refer to detailed specification
High Permittivity （Class2） Note 1 BJ, B7, C6, C7：2.5% max.
Test
Methods and
Remarks
Class 1 Class 2
Standard High Frequency Type C≦10μF C＞10μF
Preconditioning None Thermal treatment （at 150℃ for 1hr） Note 2
Measuring frequency 1ＭHz±10% 1GHz 1ｋHz±10% 120±10Hz
Measuring voltage Note 1 0.5 to 5Vrms 1±0.2Vrms 0.5±0.1Vrms
Bias application None
High Frequency Type
Measuring equipment : HP4291A
Measuring jig : HP16192A
8. Temperature Characteristic （Without voltage application）
Specified
Value
Temperature
Compensating（Class1）
Standard
Temperature Characteristic ［ppm/℃］ Tolerance ［ppm/℃］
C□ : 0 CG G : ±30
U□ : －750 UJ, UK J：±120
K：±250
SL : ＋350 to －1000
High Frequency Type Temperature Characteristic ［ppm/℃］ Tolerance ［ppm/℃］
C□ : 0 CG G : ±30
High Permittivity （Class2）
Specification Capacitance
change
Reference
temperature Temperature Range
BJ B ±10% 20℃ －25 to ＋85℃
X5R ±15% 25℃ －55 to ＋85℃
B7 X7R ±15% 25℃ －55 to ＋125℃
C6 XS ±22% 25℃ －55 to ＋105℃
C7 X7S ±22% 25℃ －55 to ＋125℃
LD(※) X5R ±15% 25℃ －55 to ＋85℃
Note : ※LD Low distortion high value multilayer ceramic capacitor
Test
Methods and
Remarks
Class 1
Capacitance at 20℃ and 85℃ shall be measured in thermal equilibrium, and the temperature characteristic shall be calculated from the
following equation.
（C85－C20） ×106（ppm/℃）
C20×△T △T＝65
Class 2
Capacitance at each step shall be measured in thermal equilibrium, and the temperature characteristic shall be calculated from the following
equation.
Step B X5R、X7R、X6S、X7S
1 Minimum operating temperature
2 20℃ 25℃
3 Maximum operating temperature
（C－C2） ×100（%） C ：Capacitance in Step 1 or Step 3
C2 ：Capacitance in Step 2
C2
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_reli_e-E06R01
9. Deflection
Specified
Value
Temperature
Compensating（Class1）
Standard Appearance : No abnormality
Capacitance change : Within ±5% or ±0.5 pF, whichever is larger.
High Frequency Type Appearance : No abnormality
Capacitance change : Within±0.5 pF
High Permittivity （Class2） Appearance : No abnormality
Capacitance change : Within ±12.5%
Test
Methods and
Remarks
Multilayer Ceramic Capacitors
021, 042, 063, ※105 Type The other types
Board Glass epoxy-resin substrate
Thickness 0.8mm 1.6mm
Warp 1mm
Duration 10 sec.
※105 Type thickness, C： 0.2mm ,P： 0.3mm.
Capacitance measurement shall be conducted
with the board bent
10. Body Strength
Specified
Value
Temperature
Compensating（Class1）
Standard －
High Frequency Type No mechanical damage.
High Permittivity （Class2） －
Test
Methods and
Remarks
High Frequency 105Type
Applied force : 5N
Duraton : 10 sec.
11. Adhesive Strength of Terminal Electrodes
Specified
Value
Temperature
Compensating（Class1）
Standard
No terminal separation or its indication.
High Frequency Type
High Permittivity （Class2）
Test
Methods and
Remarks
Multilayer Ceramic Capacitors
021, 042, 063 Type 105 Type or more
Applied force 2N 5N
Duration 30±5 sec.
12. Solderability
Specified
Value
Temperature
Compensating（Class1）
Standard
At least 95% of terminal electrode is covered by new solder.
High Frequency Type
High Permittivity （Class2）
Test
Methods and
Remarks
Eutectic solder Lead-free solder
Solder type H60A or H63A Sn-3.0Ag-0.5Cu
Solder temperature 230±5℃ 245±3℃
Duration 4±1 sec.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_reli_e-E06R01
13. Resistance to Soldering
Specified
Value
Temperature
Compensating（Class1）
Standard
Appearance : No abnormality
Capacitance change : Within ±2.5% or ±0.25pF, whichever is larger.
Q : Initial value
Insulation resistance : Initial value
Withstanding voltage （between terminals） : No abnormality
High Frequency Type
Appearance : No abnormality
Capacitance change : Within ±2.5%
Q : Initial value
Insulation resistance : Initial value
Withstanding voltage （between terminals） : No abnormality
High Permittivity （Class2） Note 1
Appearance : No abnormality
Capacitance change : Within ±7.5%
Dissipation factor : Initial value
Insulation resistance : Initial value
Withstanding voltage （between terminals）: No abnormality
Test
Methods and
Remarks
Class 1
021, 042, 063 Type 105 Type
Preconditioning None
Preheating 150℃, 1 to 2 min. 80 to 100℃, 2 to 5 min.
150 to 200℃, 2 to 5 min.
Solder temp. 270±5℃
Duration 3±0.5 sec.
Recovery 6 to 24 hrs （Standard condition） Note 5
Class 2
021, 042、063 Type 105, 107, 212 Type 316, 325, 432 Type
Preconditioning Thermal treatment （at 150℃ for 1 hr） Note 2
Preheating 150℃, 1 to 2 min. 80 to 100℃, 2 to 5 min.
150 to 200℃, 2 to 5 min.
80 to 100℃, 5 to 10 min.
150 to 200℃, 5 to 10 min.
Solder temp. 270±5℃
Duration 3±0.5 sec.
Recovery 24±2 hrs （Standard condition） Note 5
14. Temperature Cycle (Thermal Shock）
Specified
Value
Temperature
Compensating（Class1）
Standard
Appearance : No abnormality
Capacitance change : Within ±2.5% or ±0.25pF, whichever is larger.
Q : Initial value
Insulation resistance : Initial value
Withstanding voltage （between terminals） : No abnormality
High Frequency Type
Appearance : No abnormality
Capacitance change : Within ±0.25pF
Q : Initial value
Insulation resistance : Initial value
Withstanding voltage （between terminals） : No abnormality
High Permittivity （Class2） Note 1
Appearance : No abnormality
Capacitance change : Within ±7.5%
Dissipation factor : Initial value
Insulation resistance : Initial value
Withstanding voltage （between terminals） : No abnormality
Test
Methods and
Remarks
Class 1 Class 2
Preconditioning None Thermal treatment （at 150℃ for 1 hr）
Note 2
1 cycle
Step Temperature（℃） Time（min.）
1 Minimum operating temperature 30±3
2 Normal temperature 2 to 3
3 Maximum operating temperature 30±3
4 Normal temperature 2 to 3
Number of cycles 5 times
Recovery 6 to 24 hrs （Standard condition） Note 5 24±2 hrs （Standard condition） Note 5
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_reli_e-E06R01
15. Humidity （Steady State）
Specified
Value
Temperature
Compensating（Class1）
Standard
Appearance : No abnormality
Capacitance change : Within ±5% or ±0.5pF, whichever is larger.
Q : C＜10pF : Q≧200＋10C
10≦C＜30pF : Q≧275＋2.5C
C≧30pF:Q≧350（C：Nominal capacitance）
Insulation resistance : 1000 MΩ min.
High Frequency Type
Appearance : No abnormality
Capacitance change : Within ±0.5pF,
Insulation resistance : 1000 MΩ min.
High Permittivity （Class2） Note 1
Appearance : No abnormality
Capacitance change : Within ±12.5%
Dissipation factor : 5.0% max.
Insulation resistance : 50 MΩμF or 1000 MΩ whichever is smaller.
Test
Methods and
Remarks
Class 1 Class 2
Standard High Frequency Type All items
Preconditioning None Thermal treatment（ at 150℃ for 1 hr） Note 2
Temperature 40±2℃ 60±2℃ 40±2℃
Humidity 90 to 95%RH 90 to 95%RH
Duration 500＋24/－0 hrs 500＋24/－0 hrs
Recovery 6 to 24 hrs （Standard condition） Note 5 24±2 hrs （Standard condition） Note 5
16. Humidity Loading
Specified
Value
Temperature
Compensating（Class1）
Standard
Appearance : No abnormality
Capacitance change : Within ±7.5% or ±0.75pF, whichever is larger.
Q : C＜30pF：Q≧100＋10C/3
C≧30pF：Q≧200 （C：Nominal capacitance）
Insulation resistance : 500 MΩ min.
High Frequency Type
Appearance : No abnormality
Capacitance change : C≦2pF：Within ±0.4 pF
C＞2pF：Within ±0.75 pF
（C：Nominal capacitance）
Insulation resistance : 500 MΩ min.
High Permittivity （Class2） Note 1
Appearance : No abnormality
Capacitance change : Within ±12.5%
Dissipation factor : 5.0% max.
Insulation resistance : 25 MΩμF or 500 MΩ, whichever is smaller.
Test
Methods and
Remarks
Class 1 Class 2
Standard High Frequency Type All items
Preconditioning None Voltage treatment
（Rated voltage are applied for 1 hour at 40℃） Note 3
Temperature 40±2℃ 60±2℃ 40±2℃
Humidity 90 to 95%RH 90 to 95%RH
Duration 500＋24/－0 hrs 500＋24/－0 hrs
Applied voltage Rated voltage Rated voltage
Charge/discharge
current 50mA max. 50mA max.
Recovery 6 to 24 hrs （Standard condition） Note 5 24±2 hrs（Standard condition） Note 5
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_reli_e-E06R01
17. High Temperature Loading
Specified
Value
Temperature
Compensating（Class1）
Standard
Appearance : No abnormality
Capacitance change : Within ±3% or ±0.3pF, whichever is larger.
Q : C＜10pF： Q≧200＋10C
10≦C＜30pF：Q≧275＋2.5C
C≧30pF： Q≧350（C：Nominal capacitance）
Insulation resistance : 1000 MΩ min.
High Frequency Type
Appearance : No abnormality
Capacitance change : Within ±3% or ±0.3pF, whichever is larger.
Insulation resistance : 1000 MΩ min.
High Permittivity （Class2） Note 1
Appearance : No abnormality
Capacitance change : Within ±12.5%
Dissipation factor : 5.0% max.
Insulation resistance : 50 MΩμF or 1000 MΩ, whichever is smaller.
Test
Methods and
Remarks
Class 1 Class 2
Standard High Frequency Type BJ, LD(※) C6 B7, C7
Preconditioning None Voltage treatment（Twice the rated voltage shall be applied for
1 hour at 85℃, 105℃ or 125℃） Note 3, 4
Temperature Maximum operating temperature Maximum operating temperature
Duration 1000＋48/－0 hrs 1000＋48/－0 hrs
Applied voltage Rated voltage×2 Note 4 Rated voltage×2 Note 4
Charge/discharge
current 50mA max. 50mA max.
Recovery 6 to 24hr （Standard condition） Note 5 24±2 hrs （Standard condition） Note 5
Note: ※LD Low distortion high value multilayer ceramic capacitor
Note 1 The figures indicate typical specifications. Please refer to individual specifications in detail.
Note 2 Thermal treatment : Initial value shall be measured after test sample is heat-treated at 150＋0/－10℃ for an hour and kept at room temperature for
24±2hours.
Note 3 Voltage treatment : Initial value shall be measured after test sample is voltage-treated for an hour at both the temperature and voltage specified in
the test conditions, and kept at room temperature for 24±2hours.
Note 4 150% of rated voltage is applicable to some items. Please refer to their specifications for further information.
Note 5 Standard condition: Temperature: 5 to 35℃, Relative humidity: 45 to 85 % RH, Air pressure: 86 to 106kPa When there are questions concerning
measurement results, in order to provide correlation data, the test shall be conducted under the following condition.
Temperature: 20±2℃, Relative humidity: 60 to 70 % RH, Air pressure: 86 to 106kPa Unless otherwise specified, all the tests are conducted under the
"standard condition".
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_CFcap_reli_e-E05R01
Multilayer Ceramic Capacitors , Medium-High Voltage Multilayer Ceramic Capacitors and
High Reliability Application Multilayer Ceramic Capacitors are noted separately.
Super Low Distortion Multilayer Ceramic Capacitors
■RELIABILITY DATA
1. Operating Temperature Range
Specified Value －55 to ＋125℃
2. Storage Temperature Range
Specified Value －55 to ＋125℃
3. Rated Voltage
Specified Value 6.3VDC, 10VDC, 16VDC, 25VDC, 35VDC, 50VDC
4. Dielectric Withstanding Voltage （Between terminals）
Specified Value No breakdown or damage
Test Methods and
Remarks
Applied voltage : Rated voltage×3
Duration : 1 to 5 sec.
Charge/discharge current : 50mA max.
５．Insulation Resistance
Specified Value 10000 MΩ or 500MΩμF, whichever is smaller
Test Methods and
Remarks
Applied voltage : Rated voltage
Duration : 60±5 sec.
Charge/discharge current : 50mA max.
6．Capacitance （Tolerance）
Specified Value ±10％
Test Methods and
Remarks
Measuring frequency : 1kHz±10%
Measuring voltage : 1±0.2Vrms
Bias application : None
７．Dissipation Factor
Specified Value 0.1%max
Test Methods and
Remarks
Measuring frequency : 1kHz±10%
Measuring voltage : 1±0.2Vrms
Bias application : None
8．Bending Strength
Specified Value Appearance : No abnormality
Capacitance change : ±5%
Test Methods and
Remarks
Warp : 1mm
Speed : 0.5mm/second
Duration : 10 seconds
Test board : glass epoxy resin substrate
Thickness : 1.6mm
Capacitance measurement shall be conducted with the board bent.
9．Adhesive Force of Terminal Electrodes
Specified Value Terminal electrodes shall be no exfoliation or a sign of exfoliation.
Test Methods and
Remarks
Applied force : 5N
Duration : 30 ±5 seconds
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_CFcap_reli_e-E05R01
10．Solderability
Specified Value At least 95% of terminal electrode is covered by new solder.
Test Methods and
Remarks
Eutectic solder Lead-free solder
Solder type H60A or H63A Sn-3.0Ag-0.5Cu
Solder temperature 230±5℃ 245±3℃
Duration 4±1 sec.
11．Resistance to Soldering Heat
Specified Value
Appearance : No abnormality
Capacitance change : ±2.5% max.
Dissipation factor : Initial value
Insulation resistance : Initial value
Withstanding voltage （between terminals） : No abnormality
Test Methods and
Remarks
Solder temp. : 270 ±5℃
Duration : 3 ±0.5 sec.
Preheating conditions : 80 to 100℃, 2 to 5 min. or 5 to 10 min.
150 to 200℃, 2 to 5 min. or 5 to 10 min.
Measurement shall be conducted : 24±2hrs under the standard condition Note1
12．Temperature Cycle （Thermal Shock）
Specified Value
Appearance : No abnormality
Capacitance change : ±2.5% max
Dissipation factor : Initial value
Insulation resistance : Initial value
Withstanding voltage （between terminals）: No abnormality
Test Methods and
Remarks
Conditions for 1 cycle
Step temperature（℃） Time（min.）
1 Minimum operating temperature 30±3 min.
2 Normal temperature 2 to 3 min.
3 Maximum operating temperature 30±3 min.
4 Normal temperature 2 to 3 min.
Number of cycles: 5 times
Measurement shall be conducted : 24±2hrs under the standard condition Note1
13．Humidity （Steady state）
Specified Value
Appearance : No abnormality
Capacitance change : ±5% max
Dissipation factor : 0.5% max
Insulation resistance : 50MΩμF or 1000MΩ, whichever is smaller
Test Methods and
Remarks
Temperature : 40±2℃
Humidity : 90 to 95% RH
Duration : 500 ＋24/－0 hrs
Measurement shall be conducted : 24 ±2hrs under the standard condition Note1
14．Humidity Loading
Specified Value
Appearance : No abnormality
Capacitance change : ±7.5% max
Dissipation factor : 0.5% max
Insulation resistance : 25MΩμF or 500MΩ, whichever is smaller
Test Methods and
Remarks
According to JIS C 5101-1.
Temperature : 40±2℃
Humidity : 90 to 95% RH
Duration : 500 ＋24/－0 hrs
Applied voltage : Rated voltage
Charge/discharge current : 50mA max
Measurement shall be conducted : 24 ±2hrs under the standard condition Note1
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_CFcap_reli_e-E05R01
15．High Temperature Loading
Specified Value
Appearance : No abnormality
Capacitance change : ±3% max
Dissipation factor : 0.35% max
Insulation resistance : 50MΩμF or 1000MΩ, whichever is smaller
Test Methods and
Remarks
According to JIS C 5101-1.
Temperature : Maximum operating temperature
Duration : 1000 ＋48/－0 hrs
Applied voltage : Rated voltage x 2
Charge/discharge current : 50mA max
Measurement shall be conducted : 24 ±2hrs under the standard condition Note1
Note1 Standard condition: Temperature: 5 to 35℃, Relative humidity: 45 to 85 % RH, Air pressure: 86 to 106kPa
When there are questions concerning measurement results, in order to provide correlation data, the test shall be conducted under the following condition.
Temperature: 20±2℃, Relative humidity: 60 to 70 % RH, Air pressure: 86 to 106kPa
Unless otherwise specified, all the tests are conducted under the "standard condition".
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_mhv_reli_e-E06R01
Multilayer Ceramic Capacitors , Super Low Distortion Multilayer Ceramic Capacitors and
High Reliability Application Multilayer Ceramic Capacitors are noted separately.
Medium-High Voltage Multilayer Ceramic Capacitor
■RELIABILITY DATA
1. Operating Temperature Range
Specified Value
Temperature Compensating（Class1）
CG : －55 to ＋125℃
High Permittivity （Class2）
X7R, X7S : －55 to ＋125℃
X5R : －55 to ＋85℃
B : －25 to ＋85℃
SD : －55 to ＋125℃
2. Storage Temperature Range
Specified Value
Temperature Compensating（Class1）
CG : －55 to ＋125℃
High Permittivity （Class2）
X7R, X7S : －55 to ＋125℃
X5R : －55 to ＋85℃
B : －25 to ＋85℃
SD : －55 to ＋125℃
3. Rated Voltage
Specified Value Temperature Compensating（Class1） 100VDC(HMK)
High Permittivity （Class2） 100VDC(HMK), 250VDC(QMK), 630VDC(SMK)
4. Withstanding Voltage（Between terminals）
Specified Value No breakdown or damage
Test Methods and
Remarks
Applied voltage : Rated voltage×2.5（HMK）, Rated voltage×2（QMK）, Rated voltage×1.2（SMK）
Duration : 1 to 5sec.
Charge/discharge current : 50mA max.
5. Insulation Resistance
Specified Value Temperature Compensating（Class1） 10000 MΩ min.
High Permittivity （Class2） 100MΩ・μF or 10GΩ, whichever is smaller.
Test Methods and
Remarks
Applied voltage : Rated voltage（HMK, QMK）, 500V（SMK）
Duration : 60±5sec.
Charge/discharge current : 50mA max.
6. Capacitance （Tolerance）
Specified Value Temperature Compensating（Class1）
0.2pF≦C≦5pF ： ±0.25pF
0.2pF≦C≦10pF ： ±0.5pF
C＞10pF ： ±5% or ±10%
High Permittivity （Class2） ±10%, ±20%
Test Methods and
Remarks
Temperature Compensating（Class1）
Measuring frequency : 1MHz±10%
Measuring voltage : 0.5～5Vrms
Bias application : None
High Permittivity （Class2）
Measuring frequency : 1kHz±10%
Measuring voltage : 1±0.2Vrms
Bias application : None
7. Q or Dissipation Factor
Specified Value Temperature Compensating（Class1） C＜30pF : Q≧400＋20C
C≧30pF : Q≧1000 （C：Nominal capacitance）
High Permittivity （Class2） 3.5%max（HMK）,2.5%max（QMK, SMK）
Test Methods and
Remarks
Temperature Compensating（Class1）
Measuring frequency : 1MHz±10%
Measuring voltage : 0.5～5Vrms
Bias application : None
High Permittivity （Class2）
Measuring frequency : 1kHz±10%
Measuring voltage : 1±0.2Vrms
Bias application : None
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_mhv_reli_e-E06R01
8. Temperature Characteristic of Capacitance
Specified Value
Temperature Compensating（Class1）
CG ：0±30ppm/℃(－55 to ＋125℃)
High Permittivity （Class2）
B : ±10%（－25 to ＋85℃）
X5R : ±15%（－55 to ＋85℃）
X7R : ±15%（－55 to ＋125℃
X7S : ±22%（－55 to ＋125℃）
SD : - （－55 to ＋125℃）
Test Methods and
Remarks
Capacitance value at each step shall be measured in thermal equilibrium, and the temperature characteristic shall be calculated from the
following equation.
Step CG、 B、X5R、X7R、X7S、SD
1 Minimum operating temperature
2 20℃ 25℃
3 Maximum operating temperature
（C－C2） ×100（%）
C2
C : Capacitance value in Step 1 or Step 3
C2 : Capacitance value in Step 2
9. Deflection
Specified Value
Temperature Compensating（Class1） Appearance : No abnormality
Capacitance change : Within ±5% or ±0.5 pF, whichever is larger.
High Permittivity （Class2）
Appearance : No abnormality
Capacitance change : Within±10%
Test Methods and
Remarks
Warp : 1mm
Duration : 10sec.
Test board : Glass epoxy-resin substrate
Thickness : 1.6mm
Capacitance measurement shall be conducted with the board bent.
10. Adhesive Strength of Terminal Electrodes
Specified Value Temperature Compensating（Class1） No terminal separation or its indication.
High Permittivity （Class2）
Test Methods and
Remarks
Applied force : 5N
Duration : 30±5sec.
11. Solderability
Specified Value Temperature Compensating（Class1） At least 95% of terminal electrode is covered by new solder
High Permittivity （Class2）
Test Methods and
Remarks
Eutectic solder Lead-free solder
Solder type H60A or H63A Sn-3.0Ag-0.5Cu
Solder temperature 230±5℃ 245±3℃
Duration 4±1 sec.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_mhv_reli_e-E06R01
12. Resistance to Soldering
Specified Value
Temperature Compensating（Class1）
Appearance : No abnormality
Capacitance change : Within ±2.5% or ±0.25pF, whichever is larger.(HMK)
Q : Initial value
Insulation resistance : Initial value
Withstanding voltage （between terminals） : No abnormality
High Permittivity （Class2）
Appearance : No abnormality
Capacitance change : Within±15%（HMK）, ±10%（QMK, SMK）
Dissipation facto : Initial value
Insulation resistance : Initial value
Withstanding voltage （between terminals） : No abnormality
Test Methods and
Remarks
Temperature Compensating（Class1）
Preconditioning None
Solder temperature 270±5℃
Duration 3±0.5sec.
Preheating conditions 80 to 100℃, 2 to 5 min.
150 to 200℃, 2 to 5min.
Recovery 24±2hrs under the standard condition Note3
High Permittivity （Class2）
Preconditioning Thermal treatment（at 150℃ for 1hr） Note1
Solder temperature 270±5℃
Duration 3±0.5sec.
Preheating conditions 80 to 100℃, 2 to 5 min.
150 to 200℃, 2 to 5min.
Recovery 24±2hrs under the standard condition Note3
13. Temperature Cycle （Thermal Shock）
Specified Value
Temperature Compensating（Class1）
Appearance : No abnormality
Capacitance change : Within ±2.5% or ±0.25pF, whichever is larger.(HMK)
Q : Initial value
Insulation resistance : Initial value
Withstanding voltage （between terminals） : No abnormality
High Permittivity （Class2）
Appearance : No abnormality
Capacitance change : Within±15%（HMK）, ±10%（QMK, SMK）
Dissipation facto : Initial value
Insulation resistance : Initial value
Withstanding voltage （between terminals） : No abnormality
Test Methods and
Remarks
Class 1 Class 2
Preconditioning None Thermal treatment （at 150℃ for 1 hr） Note 1
1 cycle
Step Temperature（℃） Time（min.）
1 Minimum operating temperature 30±3
2 Normal temperature 2 to 3
3 Maximum operating temperature 30±3
4 Normal temperature 2 to 3
Number of cycles 5 times
Recovery 6 to 24 hrs （Standard condition） Note 3 24±2 hrs （Standard condition） Note 3
14. Humidity （Steady state）
Specified Value
Temperature Compensating（Class1）
Appearance : No abnormality
Capacitance change : Within ±5% or ±0.5pF, whichever is larger.(HMK)
Q : C＜10pF : Q≧200＋10C
10≦C＜30pF : Q≧275＋2.5C
C≧30pF:Q≧350（C：Nominal capacitance）
Insulation resistance : 1000 MΩ min.
High Permittivity （Class2）
Appearance : No abnormality
Capacitance change : Within±15%
Dissipation factor : 7%max（HMK）, 5%max（QMK, SMK）.
Insulation resistance : 25MΩμF or 1000MΩ, whichever is smaller.
Test Methods and
Remarks
Class 1 Class 2
Preconditioning None Thermal treatment（ at 150℃ for 1 hr） Note 1
Temperature 40±2℃ 40±2℃
Humidity 90 to 95%RH 90 to 95%RH
Duration 500＋24/－0 hrs 500＋24/－0 hrs
Recovery 6 to 24 hrs （Standard condition） Note 3 24±2 hrs （Standard condition） Note 3
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_mhv_reli_e-E06R01
15. Humidity Loading
Specified Value
Temperature Compensating（Class1）
Appearance : No abnormality
Capacitance change : Within ±7.5% or ±0.75pF, whichever is larger (HMK).
Q : C＜30pF：Q≧100＋10C/3
C≧30pF：Q≧200 （C：Nominal capacitance）
Insulation resistance : 500 MΩ min.
High Permittivity （Class2）
Appearance : No abnormality
Capacitance change : Within±15%
Dissipation factor : 7%max（HMK）, 5%max（QMK, SMK）.
Insulation resistance : 10MΩμF or 500MΩ, whichever is smaller.
Test Methods and
Remarks
According to JIS 5101-1.
Class 1 Class 2
Preconditioning None Voltage treatment
（Rated voltage are applied for 1 hour at 40℃） Note 2
Temperature 40±2℃ 40±2℃
Humidity 90 to 95%RH 90 to 95%RH
Duration 500＋24/－0 hrs 500＋24/－0 hrs
Applied voltage Rated voltage Rated voltage
Charge/discharge
current 50mA max. 50mA max.
Recovery 6 to 24 hrs （Standard condition） Note 3 24±2 hrs（Standard condition） Note 3
16. High Temperature Loading
Specified Value
Temperature Compensating（Class1）
Appearance : No abnormality
Capacitance change : Within ±7.5% or ±0.75pF, whichever is larger.(HMK)
Q : C＜30pF：Q≧100＋10C/3
C≧30pF：Q≧200 （C：Nominal capacitance）
Insulation resistance : 500 MΩ min.
High Permittivity （Class2）
Appearance : No abnormality
Capacitance change : Within±15%
Dissipation factor : 7%max（HMK）, 5%max（QMK, SMK）.
Insulation resistance : 50MΩμF or 1000MΩ, whichever is smaller.
Test Methods and
Remarks
According to JIS 5101-1.
Class 1 Class 2
Preconditioning None Voltage treatment Note 2
Temperature Maximum operating temperature Maximum operating temperature
Duration 1000＋48/－0 hrs 1000＋48/－0 hrs
Applied voltage Rated voltage×2(HMK) Rated voltage×2(HMK), Rated voltage×1.5（QMK）,
Rated voltage×1.2（SMK）
Charge/discharge
current 50mA max. 50mA max.
Recovery 6 to 24hr （Standard condition） Note 3 24±2 hrs （Standard condition） Note 3
Note1 Thermal treatment : Initial value shall be measured after test sample is heat-treated at 150＋0/－10℃ for an hour and kept at room temperature
for 24±2hours.
Note2 Voltage treatment : Initial value shall be measured after test sample is voltage-treated for an hour at both the temperature and voltage specified in the
test conditions, and kept at room temperature for 24±2hours.
Note3 Standard condition : Temperature: 5 to 35℃, Relative humidity: 45 to 85 % RH, Air pressure: 86 to 106kPa
When there are questions concerning measurement results, in order to provide correlation data, the test shall be conducted under
the following condition.
Temperature: 20±2℃, Relative humidity: 60 to 70 % RH, Air pressure: 86 to 106kPa
Unless otherwise specified, all the tests are conducted under the "standard condition".
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_prec_e-E05R01
High Reliability Application Multilayer Ceramic Capacitors are noted separately.
Precautions on the use of Multilayer Ceramic Capacitors
■PRECAUTIONS
1. Circuit Design
Precautions
◆Verification of operating environment, electrical rating and performance
1. A malfunction of equipment in fields such as medical, aerospace, nuclear control, etc. may cause serious harm to human life or have
severe social ramifications.
Therefore, any capacitors to be used in such equipment may require higher safety and reliability, and shall be clearly differentiated from
them used in general purpose applications.
◆Operating Voltage （Verification of Rated voltage）
1. The operating voltage for capacitors must always be their rated voltage or less.
If an AC voltage is loaded on a DC voltage, the sum of the two peak voltages shall be the rated voltage or less.
For a circuit where an AC or a pulse voltage may be used, the sum of their peak voltages shall also be the rated voltage or less.
2. Even if an applied voltage is the rated voltage or less reliability of capacitors may be deteriorated in case that either a high frequency AC
voltage or a pulse voltage having rapid rise time is used in a circuit.
2. PCB Design
Precautions
◆Pattern configurations （Design of Land-patterns）
1. When capacitors are mounted on PCBs, the amount of solder used （size of fillet） can directly affect the capacitor performance.
Therefore, the following items must be carefully considered in the design of land patterns:
（1）Excessive solder applied can cause mechanical stresses which lead to chip breaking or cracking. Therefore, please consider
appropriate land-patterns for proper amount of solder.
（2）When more than one component are jointly soldered onto the same land, each component's soldering point shall be separated by
solder-resist.
◆Pattern configurations （Capacitor layout on PCBs）
After capacitors are mounted on boards, they can be subjected to mechanical stresses in subsequent manufacturing processes （PCB
cutting, board inspection, mounting of additional parts, assembly into the chassis, wave soldering of the boards, etc.）. For this reason, land
pattern configurations and positions of capacitors shall be carefully considered to minimize stresses.
Technical
considerations
◆Pattern configurations （Design of Land-patterns）
The following diagrams and tables show some examples of recommended land patterns to prevent excessive solder amounts.
（1）Recommended land dimensions for typical chip capacitors
●Multilayer Ceramic Capacitors : Recommended land dimensions
（unit: mm）
Wave-soldering
Type 107 212 316 325
Size L 1.6 2.0 3.2 3.2
W 0.8 1.25 1.6 2.5
A 0.8 to 1.0 1.0 to 1.4 1.8 to 2.5 1.8 to 2.5
B 0.5 to 0.8 0.8 to 1.5 0.8 to 1.7 0.8 to 1.7
C 0.6 to 0.8 0.9 to 1.2 1.2 to 1.6 1.8 to 2.5
Land patterns for PCBs
C
B A B
Chip capacitor
Land pattern
Solder-resist
L
W
Chip capacitor
Reflow-soldering
Type 021 042 063 105 107 212 316 325 432
Size L 0.25 0.4 0.6 1.0 1.6 2.0 3.2 3.2 4.5
W 0.125 0.2 0.3 0.5 0.8 1.25 1.6 2.5 3.2
A 0.095～0.135 0.15～0.25 0.20～0.30 0.45～0.55 0.8～1.0 0.8～1.2 1.8～2.5 1.8～2.5 2.5～3.5
B 0.085～0.125 0.15～0.20 0.20～0.30 0.40～0.50 0.6～0.8 0.8～1.2 1.0～1.5 1.0～1.5 1.5～1.8
C 0.110～0.150 0.15～0.30 0.25～0.40 0.45～0.55 0.6～0.8 0.9～1.6 1.2～2.0 1.8～3.2 2.3～3.5
Note：Recommended land size might be different according to the allowance of the size of the product.
●LWDC: Recommended land dimensions for reflow-soldering
（unit: mm）
Type 105 107 212
Size L 0.52 0.8 1.25
W 1.0 1.6 2.0
A 0.18～0.22 0.25～0.3 0.5～0.7
B 0.2～0.25 0.3～0.4 0.4～0.5
C 0.9～1.1 1.5～1.7 1.9～2.1
L
W
LWDC
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_prec_e-E05R01
（2）Examples of good and bad solder application
Item Not recommended Recommended
Mixed mounting of SMD and
leaded components
Lead wire of component
Solder-resist
Component placement close to
the chassis
Chassis
Solder (for grounding)
Electrode pattern
Solder-resist
Hand-soldering of leaded
components near mounted
components
Soldering iron
Lead wire of component
Solder-resist
Horizontal component
placement
Solder-resist
◆Pattern configurations （Capacitor layout on PCBs）
1-1. The following is examples of good and bad capacitor layouts ; capacitors shall be located to minimize any possible mechanical
stresses from board warp or deflection.
Items Not recommended Recommended
Deflection of board
Place the product at a right
angle to the direction of the
anticipated mechanical
stress.
1-2. The amount of mechanical stresses given will vary depending on capacitor layout. Please refer to diagram below.
E
D
C
A B
Slit
Magnitude of stress A＞B＝C＞D＞E
Perforation
1-3. When PCB is split, the amount of mechanical stress on the capacitors can vary according to the method used. The following methods
are listed in order from least stressful to most stressful: push-back, slit, V-grooving, and perforation. Thus, please consider the PCB,
split methods as well as chip location.
3. Mounting
Precautions
◆Adjustment of mounting machine
1. When capacitors are mounted on PCB, excessive impact load shall not be imposed on them.
2. Maintenance and inspection of mounting machines shall be conducted periodically.
◆Selection of Adhesives
1. When chips are attached on PCBs with adhesives prior to soldering, it may cause capacitor characteristics degradation unless the
following factors are appropriately checked : size of land patterns, type of adhesive, amount applied, hardening temperature and
hardening period. Therefore, please contact us for further information.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_prec_e-E05R01
Technical
considerations
◆Adjustment of mounting machine
1. When the bottom dead center of a pick-up nozzle is too low, excessive force is imposed on capacitors and causes damages. To avoid
this, the following points shall be considerable.
（1）The bottom dead center of the pick-up nozzle shall be adjusted to the surface level of PCB without the board deflection.
（2）The pressure of nozzle shall be adjusted between 1 and 3 N static loads.
（3）To reduce the amount of deflection of the board caused by impact of the pick-up nozzle, supporting pins or back-up pins shall be
used on the other side of the PCB. The following diagrams show some typical examples of good and bad pick-up nozzle
placement:
Item Improper method Proper method
Single-sided mounting
chipping
or cracking
supporting pins
or back-up pins
Double-sided mounting
chipping
or cracking
supporting pins
or back-up pins
2. As the alignment pin is worn out, adjustment of the nozzle height can cause chipping or cracking of capacitors because of mechanical
impact on the capacitors.
To avoid this, the monitoring of the width between the alignment pins in the stopped position, maintenance, check and replacement of
the pin shall be conducted periodically.
◆Selection of Adhesives
Some adhesives may cause IR deterioration. The different shrinkage percentage of between the adhesive and the capacitors may result in
stresses on the capacitors and lead to cracking. Moreover, too little or too much adhesive applied to the board may adversely affect
components. Therefore, the following precautions shall be noted in the application of adhesives.
（1）Required adhesive characteristics
a. The adhesive shall be strong enough to hold parts on the board during the mounting & solder process.
b. The adhesive shall have sufficient strength at high temperatures.
c. The adhesive shall have good coating and thickness consistency.
d. The adhesive shall be used during its prescribed shelf life.
e. The adhesive shall harden rapidly.
f. The adhesive shall have corrosion resistance.
g. The adhesive shall have excellent insulation characteristics.
h. The adhesive shall have no emission of toxic gasses and no effect on the human body.
（2）The recommended amount of adhesives is as follows;
［Recommended condition］
Figure 212/316 case sizes as examples
a 0.3mm min
b 100 to 120μm
c Adhesives shall not contact land
Amount adhesive
a a
b
After capacitor are bonded
c c
4. Soldering
Precautions
◆Selection of Flux
Since flux may have a significant effect on the performance of capacitors, it is necessary to verify the following conditions prior to use;
（1）Flux used shall be less than or equal to 0.1 wt%（ in Cl equivalent） of halogenated content. Flux having a strong acidity content shall
not be applied.
（2）When shall capacitors are soldered on boards, the amount of flux applied shall be controlled at the optimum level.
（3）When water-soluble flux is used, special care shall be taken to properly clean the boards.
◆Soldering
Temperature, time, amount of solder, etc. shall be set in accordance with their recommended conditions.
Sn-Zn solder paste can adversely affect MLCC reliability.
Please contact us prior to usage of Sn-Zn solder.
Technical
considerations
◆Selection of Flux
1-1. When too much halogenated substance（Chlorine, etc.） content is used to activate flux, or highly acidic flux is used, it may lead to
corrosion of terminal electrodes or degradation of insulation resistance on the surfaces of the capacitors.
1-2. Flux is used to increase solderability in wave soldering. However if too much flux is applied, a large amount of flux gas may be emitted
and may adversely affect the solderability. To minimize the amount of flux applied, it is recommended to use a flux-bubbling system.
1-3. Since the residue of water-soluble flux is easily dissolved in moisture in the air, the residues on the surfaces of capacitors in high
humidity conditions may cause a degradation of insulation resistance and reliability of the capacitors. Therefore, the cleaning
methods and the capability of the machines used shall also be considered carefully when water-soluble flux is used.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_prec_e-E05R01
◆Soldering
･ Ceramic chip capacitors are susceptible to thermal shock when exposed to rapid or concentrated heating or rapid cooling.
･ Therefore, the soldering must be conducted with great care so as to prevent malfunction of the components due to excessive thermal
shock.
･ Preheating : Capacitors shall be preheated sufficiently, and the temperature difference between the capacitors and solder shall be within
130℃.
･ Cooling : The temperature difference between the capacitors and cleaning process shall not be greater than 100℃.
［Reflow soldering］
【Recommended conditions for eutectic
soldering】
Preheating 230℃
Within 10sec.
Slow cooling
60sec.
Min.
60sec
Min.
300
200
100
0
Temperature（℃）
【Recommended condition for Pb-free
soldering】
Peak
260℃ Max.
Within 10sec.
Slow
cooling
Heating above
230℃
40sec. Max.
300
200
100
0
Temperature（℃）
Preheating150℃
60sec. Min.
Caution
①The ideal condition is to have solder mass（fillet）controlled to 1/2 to 1/3 of the
thickness of a capacitor.
②Because excessive dwell times can adversely affect solderability, soldering duration shall
be kept as close to recommended times as possible. soldering for 2 times.
1/2T～1/3T
PC board
Solder
Capacitor
T
［Wave soldering］
【Recommended conditions for eutectic
soldering】
230～250℃
Within 3sec.
Slow cooling
Preheating
120sec. Min.
300
200
100
0
Temperature（℃）
【Recommended condition for Pb-free
soldering】
Peak
260℃ Max.
Within 10sec.
Slow
cooling
120sec. Min.
300
200
100
0
Temperature（℃）
Preheating
150℃
Caution
①Wave soldering must not be applied to capacitors designated as for reflow soldering only. soldering for 1 times.
［Hand soldering］
【Recommended conditions for eutectic
soldering】
230～280℃
Within 3sec.
Slow cooling
Preheating
60sec. Min.
400
200
100
0
Temperature（℃）
300
【Recommended condition for Pb-free
soldering】
Peak
350℃ Max.
Within 3sec.
Slow cooling
⊿T
400
200
100
0
Temperature（℃）
Preheating
150℃ Min.
60sec. Min.
300
⊿T
316type or less ⊿T≦150℃
Peak
280℃ Max.
Within 3sec.
Slow cooling
⊿T
400
200
100
0
温度（℃）
Preheating
150℃ Min.
60sec. Min.
300
⊿T
325type or more ⊿T≦130℃
Caution
①Use a 50W soldering iron with a maximum tip diameter of 1.0 mm.
②The soldering iron shall not directly touch capacitors. soldering for 1 times.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_prec_e-E05R01
5. Cleaning
Precautions
◆Cleaning conditions
1. When PCBs are cleaned after capacitors mounting, please select the appropriate cleaning solution in accordance with the intended use
of the cleaning. （e.g. to remove soldering flux or other materials from the production process.）
2. Cleaning condition shall be determined after it is verified by using actual cleaning machine that the cleaning process does not affect
capacitor's characteristics.
Technical
considerations
1. The use of inappropriate cleaning solutions can cause foreign substances such as flux residue to adhere to capacitors or deteriorate
their outer coating, resulting in a degradation of the capacitor's electrical properties （especially insulation resistance）.
2. Inappropriate cleaning conditions（ insufficient or excessive cleaning） may adversely affect the performance of the capacitors.
In the case of ultrasonic cleaning, too much power output can cause excessive vibration of PCBs which may lead to the cracking of
capacitors or the soldered portion, or decrease the terminal electrodes' strength. Therefore, the following conditions shall be carefully
checked;
Ultrasonic output : 20 W/ℓ or les Ultrasonic frequency : 40 kHz or less
Ultrasonic washing period : 5 min. or less
6. Resin coating and mold
Precautions
1. With some type of resins, decomposition gas or chemical reaction vapor may remain inside the resin during the hardening period or while
left under normal storage conditions resulting in the deterioration of the capacitor's performance.
2. When a resin's hardening temperature is higher than capacitor's operating temperature, the stresses generated by the excessive heat
may lead to damage or destruction of capacitors.
The use of such resins, molding materials etc. is not recommended.
7. Handling
Precautions
◆Splitting of PCB
1. When PCBs are split after components mounting, care shall be taken so as not to give any stresses of deflection or twisting to the board.
2. Board separation shall not be done manually, but by using the appropriate devices.
◆Mechanical considerations
Be careful not to subject capacitors to excessive mechanical shocks.
（1）If ceramic capacitors are dropped onto a floor or a hard surface, they shall not be used.
（2）Please be careful that the mounted components do not come in contact with or bump against other boards or components.
8. Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep packaging materials in good condition, care must be taken to control
temperature and humidity in the storage area. Humidity should especially be kept as low as possible.
・Recommended conditions
Ambient temperature : Below 30℃ Humidity : Below 70% RH
The ambient temperature must be kept below 40℃. Even under ideal storage conditions, solderability of capacitor is deteriorated as
time passes, so capacitors shall be used within 6 months from the time of delivery.
・Ceramic chip capacitors shall be kept where no chlorine or sulfur exists in the air.
2. The capacitance values of high dielectric constant capacitors will gradually decrease with the passage of time, so care shall be taken to
design circuits. Even if capacitance value decreases as time passes, it will get back to the initial value by a heat treatment at 150℃ for
1hour.
Technical
considerations
If capacitors are stored in a high temperature and humidity environment, it might rapidly cause poor solderability due to terminal oxidation and
quality loss of taping/packaging materials. For this reason, capacitors shall be used within 6 months from the time of delivery. If exceeding the
above period, please check solderability before using the capacitors.
※RCR-2335B（Safety Application Guide for fixed ceramic capacitors for use in electronic equipment）is published by JEITA.
Please check the guide regarding precautions for deflection test, soldering by spot heat, and so on.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Taiyo Yuden:
E4K316BJ105KF-T J4K316BJ105MF-T