DATA SHEET FEATURES * DESCRIPTION NEC's UPG2022T5G is a high power GaAs MMIC SPDT (Single Pole Double Throw) switch. This device can operate from 4.8 to 5.85 GHz with low insertion loss. It is housed in a 6-pin plastic SON package. OPERATING FREQUENCY: UE f = 4.8 to 5.85 GHz * LOW INSERTION LOSS: 0.8 dB TYP. @ f = 4.9 GHz 0.7 dB TYP. @ f = 5.2 GHz 0.8 dB TYP. @ f = 5.8 GHz * APPLICATIONS POWER HANDLING: Pin (0.1 dB) = +31 dBm TYP. @ f = 4.8 to 5.85 GHz CONTROL VOLTAGE: * 5 GHz CORDLESS PHONES Vcont = +2.8 V/0 V * * 5 GHz BAND WLAN IN * D NEC's 4.8 TO 5.85 GHz UPG2022T5G HIGH POWER GaAs MMIC SPDT SWITCH * 5 GHz ELECTRONIC TOLL COLLECTION HIGH ISOLATION: (Between INPUT and OUTPUT) = 23 dB TYP. @ f = 5.2 GHz * 5 GHz FIXED WIRELESS ACCESS (Between OUTPUT1 and OUTPUT2) = 22 dB TYP. @ f = 5.2 INPUT/OUTPUT RETURN LOSS: NT * 10 dB MIN. @ f = 4.8 to 5.85 GHz * SWITCHING SPEED: 20 ns @ tRISE/tFALL (10/90% RF) 6-PIN PLASTIC SON PACKAGE: (2.0 x 3.0 x 0.75 mm) * LEAD FREE SC O * ORDERING INFORMATION PART NUMBER UPG2022T5G-E1-A PACKAGE 6-pin plastic SON MARKING G4H SUPPLYING FORM * Embossed tape 8 mm wide * Pin 1 face the perforation side of the tape * Qty 3 kpcs/reel DI Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: UPG2022T5G California Eastern Laboratories UPG2022T5G PIN CONNECTIONS G4H 2 3 6 6 1 5 5 2 4 4 3 PIN NO. PIN NAME 1 OUTPUT1 2 3 4 5 D 1 (Bottom View) 6 ABSOLUTE MAXIMUM RATINGS (TA =+25C, unless otherwise specified) Switch Control Voltage SYMBOL Vcont Pin Operating Ambient Temperature TA Storage Temperature Tstg UNIT -6.0 to +6.0 V Note +36 dBm -45 to +85 C -55 to +150 C NT Input Power Notes | Vcont1 - Vcont2 | 6.0 V RATINGS IN PARAMETER RECOMMENDED OPERATING RANGE (TA =+25C, unless otherwise specified) PARAMETER SYMBOL MIN. TYP. MAX. UNIT Vcont (H) 2.7 2.8 3.3 V Vcont (L) -0.2 0 f 4.8 TA -40 SC O Switch Control Voltage (H) Switch Control Voltage (L) Operating Frequency DI Operating Ambient Temperature +25 GND OUTPUT2 Vcont2 INPUT UE (Top View) 0.2 V 5.85 GHz +85 C Vcont1 UPG2022T5G ELECTRICAL CHARACTERISTICS (TA = +25C, Vcont = 2.8 V/0 V, ZO = 50 , DC blocking capacitors = 27 pF, Each port, unless otherwise specified) LINS Isolation 1 (between OUTPUT1 and OUTPUT2) ISL1 Input Return Loss RLin TEST CONDITIONS 0.8 1.1 dB - 0.7 1.1 dB f = 5.8 GHz - 0.8 1.1 dB f = 4.9 GHz 13 18 - dB f = 5.2 GHz 15 f = 5.8 GHz 15 f = 4.9 GHz f = 4.9 GHz f = 5.8 GHz tSW Switching Control Current Icont tRISE/tFALL (10/90% RF) NT Switching Control Speed f = 4.9 to 5.8 GHz 22 - dB 20 - dB 10 22 - dB 10 29 - dB 10 19 - dB 10 21 - dB 10 29 - dB 10 20 - dB 30 31 - dBm - 20 - ns - 0.5 1 A IN Pin (0.1 dB) UNIT f = 5.2 GHz f = 5.2 GHz 0.1 dB Gain Compression Input Power MAX. - f = 5.8 GHz RLout TYP. f = 4.9 GHz f = 5.2 GHz Output Return Loss MIN. D Insertion Loss SYMBOL UE PARAMETER STANDARD CHARACTERISTICS FOR REFERENCE (TA = +25C, Vcont = 2.8 V/0 V, ZO = 50 , DC blocking capacitors = 27 pF, Each port, unless otherwise specified) PARAMETER ISL2 TEST CONDITIONS DI MIN. TYP. MAX. UNIT f = 4.9 GHz - 18 - dB f = 5.2 GHz - 23 - dB f = 5.8 GHz - 21 - dB SC O Isolation 2 (between INPUT and OUTPUT) SYMBOL UPG2022T5G EVALUATION CIRCUIT INPUT Vcont2 27 pF 1 000 pF 1 000 pF 27 pF 2 3 IN 1 4 UE 5 6 D Vcont1 27 pF OUTPUT2 NT OUTPUT1 SC O The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. TRUTH TABLE OF SWITCHING BY CONDITION OF CONTROL VOLTAGE VCONT1 VCONT (H) VCONT2 VCONT (H) INPUT VCONT (L) Note OUTPUT1 OUTPUT2 INPUT DI VCONT (L) INPUT OUTPUT1 OUTPUT2 OUTPUT1 OUTPUT2 Note INPUT OUTPUT1 OUTPUT2 Note In case of VCONT1 = VCONT2 = High or VCONT1 = VCONT2 = Low, (that is same control voltage for both pins), input signal of INPUT (Pin 5) is output from OUTPUT1 (Pin 1) and OUTPUT2 (Pin 3). UPG2022T5G PACKAGE DIMENSIONS 6-PIN PLASTIC SON (UNIT:mm) 0.750.1 IN 3.0 UE D 2.0 (Bottom View) 0.70.1 DI 0.290.1 0.70.1 0.35+0.07 -0.05 SC O 0.95 0.95 NT 0.19 0.25+0.07 -0.05 0.290.1 UPG2022T5G RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact your nearby sales office. Soldering Conditions Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220C or higher Preheating time at 120 to 180C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) VPS Peak temperature (package surface temperature) Time at temperature of 200C or higher Preheating time at 120 to 150C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) Wave Soldering Partial Heating IR260 VP215 Peak temperature (molten solder temperature) Time at peak temperature Preheating temperature (package surface temperature) Maximum number of flow processes Maximum chlorine content of rosin flux (% mass) : 260C or below : 10 seconds or less : 120C or below : 1 time : 0.2%(Wt.) or below WS260 Peak temperature (pin temperature) Soldering time (per side of device) Maximum chlorine content of rosin flux (% mass) : 350C or below : 3 seconds or less : 0.2%(Wt.) or below HS350 NT IN : 215C or below : 25 to 40 seconds : 30 to 60 seconds : 3 times : 0.2%(Wt.) or below Do not use different soldering methods together (except for partial heating). DI SC O Caution : 260C or below : 10 seconds or less : 60 seconds or less : 12030 seconds : 3 times : 0.2%(Wt.) or below D Infrared Reflow Condition Symbol UE Soldering Method Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. 05/18/2004 A Business Partner of NEC Compound Semiconductor Devices, Ltd. D 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 UE Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. IN CEL Pb-free products have the same base part number with a suffix added. The suffix -A indicates that the device is Pb-free. The -AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL's understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Lead (Pb) Mercury Concentration Limit per RoHS (values are not yet fixed) NT Restricted Substance per RoHS < 1000 PPM Concentration contained in CEL devices -A Not Detected < 1000 PPM Not Detected < 100 PPM Not Detected < 1000 PPM Not Detected PBB < 1000 PPM Not Detected PBDE < 1000 PPM Not Detected Cadmium SC O Hexavalent Chromium -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. DI Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL's liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.