PHOTO IC Photo IC for optical switch S6841, S8119 Photo IC with optical switch functions S6841 and S8119 are specifically designed for optical switches. A transmission mode or reflection mode optical switch can be easily configured when used in combination with an LED. Features Applications l Miniature transparent plastic package (4.5 x 5.5 mm) l Having following function at each terminal l Optical switch * Operation and margin display terminal * Synchronous/asynchronous switching terminal * Output logic switching terminal l Built-in short-circuit protective circuit l S6841: High sensitivity (0.05 W/mm2 Typ.) S8119: Large allowable background light level (10000 lx Typ.) A b s o lu te m a x im um ra tin g s (Ta = 2 5 C ) P a ra m ete r S ym b o l S u p ply vo ltag e Vcc P o w er d is sip atio n * P Output voltage Terminal AAAE Vout Input voltage Terminal ACE V in O p e ra ting tem pe ra ture T op r S to ra g e tem p e ratu re T s tg S o ld e rin g *1: Derate power dissipation at a rate of 3.3 mW/C above Ta=25 C V a lu e -0.3 to + 7 250 -0.3 to V c c -0 .3 to + 6 -25 to + 6 0 -4 0 to + 10 0 2 3 0 C , 3 s U nit V mW V C C - E le c tric a l a n d o p tic a l c h a ra c te ris tic s (Ta = 2 5 C , V c c = 5 V , u n le s s o th e rw is e n o te d ) P a ra m ete r S p e c tra l res p on se ra ng e P e a k s e ns itivity w a ve le n g th S u p ply vo ltag e C urre n t c o ns u m p tio n ON O U T te rm ina l o u tpu t c u rre n t OFF Current (LED is on) Current (LED is off) LED terminal output P u ls e c y c le P u ls e w id th P u ls e cycle S ig n al lig ht (in asynchronous mode) P u ls e w id th D S P te rm in a l o u tpu t c u rre nt S e tu p le ve l M R G term in a l O u tp u t c u rrent In p ut L cu rre n t In p ut H c u rren t SW te rm in al In p ut H vo lta ge In p ut L vo ltag e In p ut L cu rre n t In p ut H c u rren t IN V te rm in al In p ut H vo lta ge In p ut L vo ltag e T hre s h o ld lig h t le ve l In p ut s ign al le ve l 4 .5 60 570 11 2 3 .5 60 4 0 .8 2 .0 2 2 - 0 .0 5 0 .7 3500 - 0 .8 5000 - Eep H ys te risis A llow a b le b a ck g rou n d ligh t le v el P rop a g ation d e la y tim e l lp Vcc Ic c Io n Io f Ile d n Ile d f T p1 Tw 1 T p2 Tw 2 Id s p M Im rg Is w l Is w h Vswh Vswl Iin vl Iin vh V in v h V in v l S 6 8 41 Typ . 380 to 1120 820 5 .0 5 .0 650 160 5 200 - S ym b o l S yn c h ro nou s A s y nc hron ous H ys Ex T pd 1 o n T pd 1 o f T pd 2 o n T pd 2 o f Eepp C on d itio n OUT * LED terminals open S O U R C E , Vo u t= 2 .5 V S O U R C E , Vo u t= 0 V S O U R C E , V le d = 2 .5 V S O U R C E , V le d = 0 V * S IN K , V d s p = 1 .0V S IN K , V m rg = 1 .0V S O U R C E , V s w = 0 V S IN K , V s w = 5 V S O U R C E , V in v = 0 V S IN K , V in v= 5V N o b a ck gro u nd lig h t l = 85 0 n m *! * " S h ield to inp u t * " In put to s hie ld S h ie ld to in pu t In p ut to sh ield *# M in . - - 5 .5 7 .0 1 .0 725 10 2 08 6 .5 100 6 1 .6 3 .6 100 100 0 .8 100 100 0 .8 4 .5 60 570 11 2 3 .5 60 4 0 .8 2 .0 2 2 - S 8 11 9 Typ . 380 to 1120 820 5 .0 5 .0 650 160 5 200 - 0 .1 - 0 .9 1100 1100 1200 1300 1 0 .7 6000 - M a x. M in . M a x. U nit - nm 5 .5 7 .0 1 .0 725 10 208 6 .5 100 6 1 .6 3 .6 100 100 0 .8 100 100 0 .8 nm V mA A A A A s s s s mA % mA A A V V A A V V 0 .1 0 .2 W/mm 0 .8 10000 650 650 - 0 .9 900 900 1000 1300 lx s s s s W/mm 1 Photo IC for optical switch S6841, S8119 *2: Pulse cycle, pulse width: See below. Vcc to 2.5 V 0.33 F 5V LED 3.8 k 0V Tw GND Tp Measurement circuit LED terminal output waveform KPICC0060EA KPICC0061EA *3: Allowable background light level This is defined as the background light level on the active area at which the photo IC sensitivity* drops by 20 %. * Sensitivity is the reciprocal of light level, which is constantly detected as a signal. If background disturbance light strikes a part on the package (other than the active area) of S6841, this may lower the allowable background light level. Use light-impervious tape to provide light-shielding over the shaded area of the package as shown below. Light-shielding is unnecessary for S8119. ACTIVE AREA LIGHT-SHIELDED AREA KPICC0067EA Light-shielded area (S6841) *4: HL, LH propagation delay time The optical system is adjusted so that the Vo terminal output becomes "Low" voltage when the switch shown in the circuit below is off. (S6841 is then measured with a signal light input of 1 W/mm2 illuminance.) Vs SWITCH OFF Vcc LED LED OUT Vo SWITCH 0.33 F 5V Tpd Tpd ON SENS (OPEN) INV (OPEN) SW 1.5 V GND Vo OUTPUT Measurement circuit *5: This is the input signal light level for the propagation delay time to stay within specifications. If the input signal light exceeds this level, the propagation delay time may increase. 2 KPICC0062EA Photo IC for optical switch n Truth table Block diagram CONSTANT VOLTAGE CIRCUIT 1 INV terminal: HIGH Input OUT output DSP output MRG output Light ON ON ON ON Light OFF OFF OFF OFF Vcc TO EACH CIRCUIT INV terminal: LOW Input OUT output DSP output MRG output Light ON OFF OFF ON Light OFF ON ON OFF COMPARATOR PRE-AMPLIFIER BUFFER PD COMPARATOR FOR MARGIN DISPLAY REF. VOLTAGE SIGNAL PROCESSING CIRCUIT OUTPUT INVERTER CIRCUIT 2 OUT 3 SENS 4 DSP 5 MRG 10 LED 6 A. GND 7 D. GND OPERATION DISPLAY OUTPUT CIRCUIT SIGNAL PROCESSING CIRCUIT Detection Method Synchronous Asynchronous MARGIN DISPLAY OUTPUT CIRCUIT 9 OSCILLATION CIRCUIT INV SW terminal High Low OUTPUT CIRCUIT OUTPUT PROTECTIVE CIRCUIT SW S6841, S8119 TIMING GENERATOR LED DRIVER 8 KPICC0048EA Terminal configuration Vcc (100 k) Vcc DSP MRG (50 k) SW INV GND OPERATION DISPLAY TERMINAL MARGIN DISPLAY TERMINAL GND DETECTION METHOD SWITCHING TERMINAL OUTPUT SWITCHING TERMINAL Vcc LED GND LED TERMINAL KPICC0063EA 3 Photo IC for optical switch S6841, S8119 OUT terminal and SENS terminal configurations and recommended external short-circuit protective circuit Vreg Z1 OUT POWER SUPPLY TR1 SENS R ~ - 0.7 V GND KPICC0064EA Dimensional outline (unit: mm) 5.5 3 10 5.4 * X 5.6 0.2 (INCLUDING BURR) 4.6 0.2 (INCLUDING BURR) Y 5.4 * 0.4 0.89 o 0.56 ACTIVE AREA 0.53 1.0 7.5 0.3 PHOTOSENSITIVE SURFACE 5 0.7 0.3 3 0.1 0.25 0.7 0.3 2.0 1.5 0.4 4.5 * 0.75 0.15 1.5 0.4 Vcc OUT (OUTPUT) SENS (SHORT-CIRCUIT PROTECTIVE INPUT FOR OUTPUT TERMINAL LOAD) DSP (OPERATION DISPLAY) MRG (MARGIN DISPLAY) A. GND D. GND INV (OUTPUT LOGIC SWITCHING) SW (SYNCHRONOUS, ASYNCHRONOUS SWITCHING) LED Tolerance unless otherwise noted: 0.1, 2 Shaded area indicates burr. Chip position accuracy This chip is mounted with the following accuracy with respect to the package dimensions marked * X, Y 0.2 KPICA0020EB Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. (c)2001 Hamamatsu Photonics K.K. HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184, http://www.hamamatsu.com U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 08152-3750, Fax: (49) 08152-2658 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Smidesvagen 12, SE-171 41 Solna, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741 4 Cat. No. KPIC1019E02 Jul. 2001 DN