DIM2400ESM17-A000
Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. 1/10
www.dynexsemi.com
FEATURES
■10µs Short Circuit Withstand
■High Thermal Cycling Capability
■Non Punch Through Silicon
■Isolated MMC Base with AlN Substrates
APPLICATIONS
■High Reliability Inverters
■Motor Controllers
■Traction Drives
The Powerline range of modules includes half bridge, dual
and single switch configurations covering voltages from 600V to
3300V and currents up to 2400A.
The DIM2400ESM17-A000 is a single switch 1700V, n
channel enhancement mode, insulated gate bipolar transistor
(IGBT) module. The IGBT has a wide reverse bias safe
operating area (RBSOA) plus full 10µs short circuit withstand.
This module is optimised for traction drives and other
applications requiring high thermal cycling capability.
The module incorporates an electrically isolated base plate
and low inductance construction enabling circuit designers to
optimise circuit layouts and utilise grounded heat sinks for safety.
ORDERING INFORMATION
Order As:
DIM2400ESM17-A000
Note: When ordering, please use the whole part number.
KEY PARAMETERS
VCES 1700V
VCE(sat)* (typ) 2.7V
IC(max) 2400A
IC(PK) (max) 4800A
*(measured at the power busbars and not the auxiliary terminals)
DIM2400ESM17-A000
Single Switch IGBT Module
Replaces May 2001, version 5447-2.0 DS5447-3.0 March 2002
Fig. 1 Single switch circuit diagram
Fig. 2 Electrical connections - (not to scale)
Outline type code: E
(See package details for further information)
C2C1
Aux C
G
Aux E E1 E2 E3
External connection
External connection
C3
DIM2400ESM17-A000
2/10 Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures.
www.dynexsemi.com
ABSOLUTE MAXIMUM RATINGS
Stresses above those listed under 'Absolute Maximum Ratings' may cause permanent damage to the device. In extreme
conditions, as with all semiconductors, this may include potentially hazardous rupture of the package. Appropriate safety
precautions should always be followed. Exposure to Absolute Maximum Ratings may affect device reliability.
Tcase = 25˚C unless stated otherwise
Test Conditions
VGE = 0V
-
Tcase = 75˚C
1ms, Tcase = 105˚C
Tcase = 25˚C, Tj = 150˚C
VR = 0, tp = 10ms, Tvj = 125˚C
Commoned terminals to base plate. AC RMS, 1 min, 50Hz
IEC1287. V1 = 1500V, V2 = 1100V, 50Hz RMS
Symbol
VCES
VGES
IC
IC(PK)
Pmax
I2t
Visol
QPD
Units
V
V
A
A
kW
kA2s
V
PC
Max.
1700
±20
2400
4800
20.8
1080
4000
10
Parameter
Collector-emitter voltage
Gate-emitter voltage
Continuous collector current
Peak collector current
Max. transistor power dissipation
Diode I2t value (IGBT arm)
Isolation voltage - per module
Partial discharge - per module
DIM2400ESM17-A000
Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. 3/10
www.dynexsemi.com
THERMAL AND MECHANICAL RATINGS
Internal insulation material: AlN
Baseplate material: AlSiC
Creepage distance: 32mm
Clearance: 20mm
CTI (Critical Tracking Index): 175
Test Conditions
Continuous dissipation -
junction to case
Continuous dissipation -
junction to case
Mounting torque 5Nm
(with mounting grease)
Transistor
Diode
-
Mounting - M6
Electrical connections - M4
Electrical connections - M8
Parameter
Thermal resistance - transistor
Thermal resistance - diode
Thermal resistance - case to heatsink
(per module)
Junction temperature
Storage temperature range
Screw torque
Symbol
Rth(j-c)
Rth(j-c)
Rth(c-h)
Tj
Tstg
-
Units
˚C/kW
˚C/kW
˚C/kW
˚C
˚C
˚C
Nm
Nm
Nm
Max.
6
13.3
6
150
125
125
5
2
10
Typ.
-
-
-
-
-
-
-
-
-
Min.
-
-
-
-
-
–40
-
-
-
DIM2400ESM17-A000
4/10 Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures.
www.dynexsemi.com
Min.
-
-
-
4.5
-
-
-
-
-
-
-
-
-
-
-
ELECTRICAL CHARACTERISTICS
Tcase = 25˚C unless stated otherwise.
Test Conditions
VGE = 0V, VCE = VCES
VGE = 0V, VCE = VCES, Tcase = 125˚C
VGE = ±20V, VCE = 0V
IC =120mA, VGE = VCE
VGE = 15V, IC = 2400A
VGE = 15V, IC = 2400A, , Tcase = 125˚C
DC
tp = 1ms
IF = 2400A
IF = 2400A, Tcase = 125˚C
VCE = 25V, VGE = 0V, f = 1MHz
-
-
T
j
= 125˚C, V
CC
= 1000V,
I1
t
p
≤ 10µs,
V
CE(max)
= V
CES
– L*. di/dt
I2
IEC 60747-9
Parameter
Collector cut-off current
Gate leakage current
Gate threshold voltage
Collector-emitter saturation voltage
Diode forward current
Diode maximum forward current
Diode forward voltage
Input capacitance
Module inductance
Internal transistor resistance
Short circuit. ISC
Symbol
ICES
IGES
VGE(TH)
VCE(sat)†
IF
IFM
VF†
Cies
LM
RINT
SCData
Units
mA
mA
µA
V
V
V
A
A
V
V
nF
nH
mΩ
A
A
Max.
3
75
12
6.5
3.2
4.0
2400
4800
2.5
2.6
-
-
-
-
-
Typ.
-
-
-
5.5
2.7
3.4
-
-
2.2
2.3
180
10
0.27
11000
9600
Note:
† Measured at the power busbars and not the auxiliary
terminals)
* L is the circuit inductance + LM
DIM2400ESM17-A000
Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. 5/10
www.dynexsemi.com
Units
ns
ns
mJ
ns
ns
mJ
µC
µC
A
mJ
Max.
-
-
-
-
-
-
-
-
-
Typ.
2000
200
900
800
300
475
27
450
1200
300
Min.
-
-
-
-
-
-
-
-
-
Test Conditions
IC = 2400A
VGE = ±15V
VCE = 900V
RG(ON) = RG(OFF) = 1.0Ω
L ~ 50nH
IF = 2400A, VR = 50% VCES,
dIF/dt = 8500A/µs
Parameter
Turn-off delay time
Fall time
Turn-off energy loss
Turn-on delay time
Rise time
Turn-on energy loss
Gate charge
Diode reverse recovery charge
Diode reverse current
Diode reverse recovery energy
ELECTRICAL CHARACTERISTICS
Tcase = 25˚C unless stated otherwise
Symbol
td(off)
tf
EOFF
td(on)
tr
EO
Qg
Qrr
Irr
EREC
Tcase = 125˚C unless stated otherwise
Units
ns
ns
mJ
ns
ns
mJ
µC
A
mJ
Max.
-
-
-
-
-
-
-
-
-
Typ.
2300
250
1200
900
300
750
750
1400
600
Min.
-
-
-
-
-
-
-
-
-
Test Conditions
IC = 2400A
VGE = ±15V
VCE = 900V
RG(ON) = RG(OFF) = 1.0Ω
L ~ 50nH
IF = 2400A, VR = 50% VCES,
dIF/dt = 8000A/µs
Parameter
Turn-off delay time
Fall time
Turn-off energy loss
Turn-on delay time
Rise time
Turn-on energy loss
Diode reverse recovery charge
Diode reverse current
Diode reverse recovery energy
Symbol
td(off)
tf
EOFF
td(on)
tr
EON
Qrr
Irr
EREC
DIM2400ESM17-A000
6/10 Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures.
www.dynexsemi.com
TYPICAL CHARACTERISTICS
Fig. 3 Typical output characteristics Fig. 4 Typical output characteristics
Fig. 5 Typical switching energy vs collector current Fig. 6 Typical switching energy vs gate resistance
0
600
1200
1800
2400
3000
3600
4200
4800
5400
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5
Collector-emitter voltage, V
ce
- (V)
Collector current, I
c
- (A)
V
GE
= 20V
15V
12V
10V
Common emitter
T
case
= 25˚C
V
ce is measured at power busbars
and not the auxiliary terminals
0
600
1200
1800
2400
3000
3600
4200
4800
5400
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6
Collector-emitter voltage, V
ce
- (V)
Collector current, I
c
- (A)
V
GE
= 20V
15V
12V
10V
Common emitter
T
case
= 125˚C
V
ce
is measured at power busbars
and not the auxiliary terminals
0
200
400
600
800
1000
1200
1400
0 400 800 1200 1600 2000 2400
Collector current, IC - (A)
Switching energy - (mJ)
Erec
Eoff
Eon
Tcase = 125˚C
VCC = 900V,
Rg = 1Ω
L ~ 50nH
0
500
1000
1500
2000
2500
3000
00.511.522.533.544.55
Gate resistance, R
g
- (Ohms)
Switching energy (mJ)
E
rec
E
off
E
on
T
case
= 125˚C
I
C
= 2400A
R
g
= 1Ω
L ~ 50nH
DIM2400ESM17-A000
Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures.7/10
www.dynexsemi.com
Fig. 7 Diode typical forward characteristics Fig. 8 Reverse bias safe operating area
Fig. 9 Diode reverse bias safe operating area Fig. 10 Forward bias safe operating area
0
600
1200
1800
2400
3000
3600
4200
4800
00.51.01.52.02.53.03.5
Foward voltage, V
F
- (V)
Foward current, IF - (A)
T
j
= 25˚C
T
j
= 125˚C
V
F
is measured at power busbars
and not the auxiliary terminals
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
0 200 400 600 800 1000 1200 1400 1600 1800
Collector emitter voltage, V
ce
- (V)
Collector current, I
C
- (A)
T
case
= 125˚C
V
ge
= 15V Module I
C
Chip I
C
0
500
1000
1500
2000
2500
0 200 400 600 800 1000 1200 1400 1600 1800
Reverse voltage, V
R
- (V)
Reverse recovery current, Irr - (A)
Tcase =125˚C
1
10
100
1000
10000
1 10 100 1000 10000
Collector emitter voltage, V
ce
- (V)
Collector current, I
C
- (A)
T
vj
= 125˚C,
T
c
= 75˚C
I
C(max)
DC
t
p
= 1ms
t
p
= 50µs
t
p
= 100µs
DIM2400ESM17-A000
8/10 Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures.
www.dynexsemi.com
Fig. 11 Transient thermal impedance Fig. 12 DC current rating vs case temperature
0.1
10
1
100
0.001 0.01 10.110
Pulse width, t
p
- (s)
Transient thermal impedance, Z
th (j-c)
- (°C/kW )
Diode
Transistor
IGBT R
i
(˚C/KW)
τ
i
(ms)
Diode R
i
(˚C/KW)
τ
i
(ms)
1
0.1463
0.045
0.5204
0.0063516
2
1.0645
2.8869
1.9142
1.4746
3
1.3821
21.7141
2.333
13.9664
4
3.4118
152.6381
8.5356
111.7515
0
400
800
1200
1600
2000
2400
2800
3200
3600
4000
4400
4800
0 20 40 60 80 100 120 140 160
Case temperature, T
case
- (˚C)
DC collector current, I
C
- (A)
DIM2400ESM17-A000
Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures.9/10
www.dynexsemi.com
PACKAGE DETAILS
For further package information, please visit our website or contact Customer Services. All dimensions in mm, unless stated otherwise.
DO NOT SCALE.
Nominal weight: 1700g
Module outline type code: E
DIM2400ESM17-A000
10/10 Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures.
www.dynexsemi.com
POWER ASSEMBLY CAPABILITY
The Power Assembly group was set up to provide a support service for those customers requiring more than the basic
semiconductor, and has developed a flexible range of heatsink and clamping systems in line with advances in device voltages and
current capability of our semiconductors.
We offer an extensive range of air and liquid cooled assemblies covering the full range of circuit designs in general use today. The
Assembly group continues to offer high quality engineering support dedicated to designing new units to satisfy the growing needs of
our customers.
Using the latest CAD methods our team of design and applications engineers aim to provide the Power Assembly Complete
Solution (PACs).
HEATSINKS
The Power Assembly group has its own proprietary range of extruded aluminium heatsinks. They have been designed to optimise
the performance of Dynex semiconductors. Data with respect to air natural, forced air and liquid cooling (with flow rates) is
available on request.
For further information on device clamps, heatsinks and assemblies, please contact your nearest sales representative or customer
service office.
CUSTOMER SERVICE
Tel: +44 (0)1522 502753 / 502901. Fax: +44 (0)1522 500020
SALES OFFICES
Benelux, Italy & Switzerland: Tel: +33 (0)1 64 66 42 17. Fax: +33 (0)1 64 66 42 19.
France & Spain: Tel: +33 (0)2 47 55 75 52. Fax: +33 (0)2 47 55 75 59.
Germany, Northern Europe & Rest Of World: Tel: +44 (0)1522 502753 / 502901. Fax: +44 (0)1522 500020
North America: Tel: (613) 723-7035. Fax: (613) 723-1518. Toll Free: 1.888.33.DYNEX (39639) /
Tel: (949) 733-3005. Fax: (949) 733-2986.
These offices are supported by Representatives and Distributors in many countries world-wide.
© Dynex Semiconductor 2002 Publication No. DS5447-3 Issue No. 3.0 March 2002
TECHNICAL DOCUMENTATION – NOT FOR RESALE. PRODUCED IN UNITED KINGDOM
HEADQUARTERS OPERATIONS
DYNEX SEMICONDUCTOR LTD
Doddington Road, Lincoln.
Lincolnshire. LN6 3LF. United Kingdom.
Tel: 00-44-(0)1522-500500
Fax: 00-44-(0)1522-500550
This publication is issued to provide information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as
a representation relating to the products or services concerned. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. The Company reserves
the right to alter without prior notice the specification, design or price of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such
methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication
or data used is up to date and has not been superseded. These products are not suitable for use in any medical products whose failure to perform may result in significant injury
or death to the user. All products and materials are sold and services provided subject to the Company's conditions of sale, which are available on request.
All brand names and product names used in this publication are trademarks, registered trademarks or trade names of their respective owners.
http://www.dynexsemi.com
e-mail: power_solutions@dynexsemi.com
Datasheet Annotations:
Dynex Semiconductor annotate datasheets in the top right hard corner of the front page, to indicate product status. The annotations are as follows:-
Target Information: This is the most tentative form of information and represents a very preliminary specification. No actual design work on the product has been started.
Preliminary Information: The product is in design and development. The datasheet represents the product as it is understood but details may change.
Advance Information: The product design is complete and final characterisation for volume production is well in hand.
No Annotation: The product parameters are fixed and the product is available to datasheet specification.
