Current Output, Parallel Input, 16-/14-Bit Multiplying DACs with Four-Quadrant Resistors AD5546/AD5556 Data Sheet FEATURES FUNCTIONAL BLOCK DIAGRAM R1 16-bit resolution 14-bit resolution 2- or 4-quadrant multiplying DAC 1 LSB DNL 1 LSB INL Operating supply voltage: 2.7 V to 5.5 V Low noise: 12 nV/Hz Low power: IDD = 10 A 0.5 s settling time Built-in RFB facilitates current-to-voltage conversion Built-in 4-quadrant resistors allow 0 V to -10 V, 0 V to +10 V, or 10 V outputs 2 mA full-scale current 20%, with VREF = 10 V Automotive operating temperature: -40C to +125C Compact TSSOP-28 package RCOM R1 REF ROFS R2 AD5546/ AD5556 VDD WR RFB DAC RFB IOUT 16/14 CONTROL LOGIC LDAC ROFS DAC REGISTER DB0 TO DB15 GND MSB 03810-001 POR RS Figure 1. AD5546/AD5556 Simplified Block Diagram GENERAL DESCRIPTION The AD5546/AD5556 are precision 16-/14-bit, multiplying, low power, current output, parallel input digital-to-analog converters (DACs). They operate from a single 2.7 V to 5.5 V supply with 10 V multiplying references for four-quadrant outputs. Builtin four-quadrant resistors facilitate the resistance matching and temperature tracking that minimize the number of components needed for multiquadrant applications. The feedback resistor (RFB) simplifies the I-V conversion with an external buffer. The AD5546/AD5556 are packaged in compact TSSOP-28 packages with operating temperatures from -40C to +125C. APPLICATIONS Automatic test equipment Instrumentation Digitally controlled calibration Digital waveform generation The EVAL-AD5546SDZ is available for evaluating DAC performance. For more information, see the UG-309 evaluation board user guide. + U2A OP2177 - +10V C7 -10V R1A VREFA RCOMA ROFSA RFBA +15V C6 R1 ROFS VDD C1 1F C2 0.1F U1 AD5546/AD5556 IOUT 16-/14-BIT DATA - C5 0.1F V+ U2B OP2177 GND 16-/14-BIT DATA C4 1F RFB + VOUT V- C8 1F WR LDAC RS MSB WR LDAC RS MSB C9 0.1F -15V 03810-024 +5V R2 Figure 2. 16-/14-Bit, Four-Quadrant Multiplying DAC with a Minimum of External Components Rev. D Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2004-2011 Analog Devices, Inc. All rights reserved. AD5546/AD5556 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Digital Section ............................................................................ 11 Applications ....................................................................................... 1 ESD Protection Circuits ............................................................ 11 Functional Block Diagram .............................................................. 1 Amplifier Selection .................................................................... 11 General Description ......................................................................... 1 Reference Selection .................................................................... 11 Revision History ............................................................................... 2 Applications Information .............................................................. 12 Specifications..................................................................................... 3 Unipolar Mode ........................................................................... 12 Electrical Characteristics ............................................................. 3 Bipolar Mode .............................................................................. 13 Timing Diagram ........................................................................... 4 AC Reference Signal Attenuator ............................................... 14 Absolute Maximum Ratings ............................................................ 5 System Calibration ..................................................................... 14 ESD Caution .................................................................................. 5 Reference Selection .................................................................... 15 Pin Configurations and Function Descriptions ........................... 6 Amplifier Selection .................................................................... 15 Typical Performance Characteristics ............................................. 8 Outline Dimensions ....................................................................... 17 Circuit Operation ........................................................................... 10 Ordering Guide .......................................................................... 17 Digital-to-Analog (DAC) Converter Section ......................... 10 REVISION HISTORY 11/11--Rev. C to Rev. D Changes to General Description Section ...................................... 1 Changes to Ordering Guide .......................................................... 18 1/11--Rev. B to Rev. C Changes to Figure 2 .......................................................................... 1 Changes to Figure 21 ...................................................................... 13 4/10--Rev. A to Rev. B Changes to Table 1 ............................................................................ 4 Moved Timing Diagram Section and Figure 5 to Specifications Section....................................................................... 4 Moved Table 5 Through Table 7 to Digital Section Section ....... 7 Replaced Figure 15 and Figure 16 .................................................. 9 Deleted Figure 17 and Figure 18..................................................... 9 Added Reference Selection Section, Amplifier Selection Section, and Table 11 Through Table 13 .................................................... 15 9/09--Rev. 0 to Rev. A Changes to Features Section............................................................ 1 Changes to Static Performance, Relative Accuracy, Grade: AD5546C Parameter, Table 1 ............................................. 3 Changes to Ordering Guide .......................................................... 16 1/04--Revision 0: Initial Version Rev. D | Page 2 of 20 Data Sheet AD5546/AD5556 SPECIFICATIONS ELECTRICAL CHARACTERISTICS VDD = 2.7 V to 5.5 V, IOUT = virtual GND, GND = 0 V, VREF = -10 V to 10 V, TA = full operating temperature range, unless otherwise noted. Table 1. Parameter STATIC PERFORMANCE 1 Resolution Symbol Conditions N AD5546, 1 LSB = VREF/216 = 153 V at VREF = 10 V AD5556, 1 LSB = VREF/214 = 610 V at VREF = 10 V Grade: AD5556C Grade: AD5546B Grade: AD5546C Monotonic Data = zero scale, TA = 25C Data = zero scale, TA = TA maximum Data = full scale Data = full scale Data = full scale Relative Accuracy INL Differential Nonlinearity Output Leakage Current DNL IOUT Full-Scale Gain Error Bipolar Mode Gain Error Bipolar Mode Zero-Scale Error Full-Scale Tempco2 REFERENCE INPUT VREF Range REF Input Resistance R1 and R2 Resistance R1-to-R2 Mismatch Feedback and Offset Resistance Input Capacitance2 ANALOG OUTPUT Output Current Output Capacitance2 LOGIC INPUT AND OUTPUT Logic Input Low Voltage GFSE GE GZSE Logic Input High Voltage Min -18 4 4 8 CREF IOUT COUT Data = full scale Code dependent VIL VDD = 5 V VDD = 3 V VDD = 5 V VDD = 3 V IIL CIL Data to WR Hold Time tDH WR Pulse Width tWR LDAC Pulse Width tLDAC tDS Unit Bits 14 Bits 1 2 1 1 10 20 4 4 2.5 1 VREF REF R1 and R2 (R1 to R2) RFB, ROFS Input Leakage Current Input Capacitance2 INTERFACE TIMING2, 3 Data to WR Setup Time Max 16 1 1 1 TCVFS VIH Typ 5 5 0.5 10 LSB LSB LSB LSB nA nA mV mV mV ppm/C +18 6 6 1.5 12 V k k k 5 pF 2 200 mA pF 0.8 0.4 2.4 2.1 10 10 V V V V A pF VDD = 5 V VDD = 3 V VDD = 5 V VDD = 3 V VDD = 5 V 20 35 0 0 20 ns ns ns ns ns VDD = 3 V VDD = 5 V VDD = 3 V 35 20 35 ns ns ns Rev. D | Page 3 of 20 AD5546/AD5556 Parameter RS Pulse Width WR to LDAC Delay Time SUPPLY CHARACTERISTICS Power Supply Range Positive Supply Current Power Dissipation Power Supply Sensitivity AC CHARACTERISTICS4 Output Voltage Settling Time Reference Multiplying BW DAC Glitch Impulse Multiplying Feedthrough Error Digital Feedthrough Total Harmonic Distortion Output Noise Density Data Sheet Symbol tRS tLWD VDD RANGE IDD PDISS PSS tS Conditions VDD = 5 V VDD = 3 V VDD = 5 V VDD = 3 V Min 20 35 0 0 Typ 2.7 Logic inputs = 0 V Logic inputs = 0 V VDD = 5% Max Unit ns ns ns ns 5.5 10 0.055 0.003 V A mW %/% 0.5 s BW Q VOUT/VREF To 0.1% of full scale, data cycles from zero scale to full scale to zero scale VREF = 100 mV rms, data = full scale, C6 =5.6 pF5 VREF = 0 V, midscale minus 1 to midscale VREF = 100 mV rms, f = 10 kHz 6.8 -3 79 MHz nV-s dB QD THD eN WR = 1, LDAC toggles at 1 MHz VREF = 5 V p-p, data = full-scale, f = 1 kHz f = 1 kHz, BW = 1 Hz 7 -103 12 nV-s dB nV/rt Hz 1 All static performance tests (except IOUT) are performed in a closed-loop system, using an external precision OP97 I-V converter amplifier. The AD554x RFB terminal is tied to the amplifier output. The op amp +IN is grounded, and the DAC IOUT is tied to the op amp -IN. Typical values represent average readings measured at 25C. 2 These parameters are guaranteed by design and are not subject to production testing. 3 All input control signals are specified with tR = tF = 2.5 ns (10% to 90% of 3 V) and timed from a voltage level of 1.5 V. 4 All ac characteristic tests are performed in a closed-loop system using an AD8038 I-V converter amplifier except for THD where an AD8065 was used. 5 C6 is the C6 capacitor shown in Figure 20. TIMING DIAGRAM tWR WR DATA tDS tDH tLWD LDAC tRS 03810-005 tLDAC RS Figure 3. AD5546/AD5556 Timing Diagram Rev. D | Page 4 of 20 Data Sheet AD5546/AD5556 ABSOLUTE MAXIMUM RATINGS Table 2. Parameter VDD to GND RFB, ROFS, R1, RCOM, and REF to GND Logic Inputs to GND V (IOUT) to GND Input Current to Any Pin Except Supplies Thermal Resistance (JA) Maximum Junction Temperature (TJ MAX) Operating Temperature Range Storage Temperature Range Lead Temperature: Vapor Phase, 60 s Infrared, 15 s Package Power Dissipation Rating -0.3 V, +8 V -18 V, 18 V -0.3 V, +8 V -0.3 V, VDD + 0.3 V 50 mA 128C 150C -40C to +125C -65C to +150C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION 215C 220C (TJ MAX - TA)/JA Rev. D | Page 5 of 20 AD5546/AD5556 Data Sheet PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS D7 1 28 VDD D5 1 28 VDD D6 2 27 D8 D4 2 27 D6 D5 3 26 D9 D3 3 26 D7 D4 4 25 D10 D2 4 25 D8 D2 6 AD5546 24 D11 D1 5 23 D12 D0 6 22 D13 TOP VIEW D0 8 (Not to Scale) 21 D14 D1 7 RFB 10 R1 11 RCOM 12 20 D15 19 GND 18 RS 17 MSB REF 13 16 WR IOUT 14 15 LDAC 24 D9 23 D10 22 D11 NC 7 TOP VIEW NC 8 (Not to Scale) 21 D12 03810-003 ROFS 9 AD5556 ROFS 9 20 D13 RFB 10 19 GND R1 11 18 RS RCOM 12 17 MSB REF 13 16 WR IOUT 14 15 LDAC NC = NO CONNECT Figure 4. AD5546 Pin Configuration 03810-004 D3 5 Figure 5. AD5556 Pin Configuration Table 3. AD5546 Pin Function Descriptions Pin No. 1 to 8 9 Mnemonic D7 to D0 ROFS 10 11 12 RFB R1 RCOM 13 REF 14 15 16 IOUT LDAC WR 17 MSB 18 RS 19 20 to 21 22 to 27 28 GND D15 to D14 D13 to D8 VDD Description Digital Input Data Bits[D7: D0]. The signal level must be VDD + 0.3 V. Bipolar Offset Resistor. Accepts up to 18 V. In two-quadrant mode, ties to RFB. In four-quadrant mode, ties to R1 and the external reference. Internal Matching Feedback Resistor. Connects to the output of an external op amp for I-V conversion. Four-Quadrant Resistor R1. In two-quadrant mode, shorts to the REF pin. In four-quadrant mode, ties to ROFS. Center Tap Point of Two Four-Quadrant Resistors, R1 and R2. In four-quadrant mode, ties to the inverting node of the reference amplifier. In two-quadrant mode, shorts to the REF pin. DAC Reference Input in Two-Quadrant Mode and R2 Terminal in Four-Quadrant Mode. In two-quadrant mode, this pin is the reference input with constant input resistance vs. code. In four-quadrant mode, this pin is driven by the external reference amplifier. DAC Current Output. Connects to the inverting node of an external op amp for I-V conversion. Digital Input Load DAC Control. Signal level must be VDD + 0.3 V. Write Control Digital Input in Active Low. Transfers shift-register data to the DAC register on the rising edge. The signal level must be VDD + 0.3 V. Power-On Reset State. MSB = 0 resets at zero scale; MSB = 1 resets at midscale. The signal level must be VDD + 0.3 V. Reset in Active Low. Resets to zero scale if MSB = 0, and resets to midscale if MSB = 1. The signal level must be VDD + 0.3 V. Analog and Digital Grounds. Digital Input Data Bits[D15:D14]. The signal level must be VDD + 0.3 V. Digital Input Data Bits[D13:D8]. The signal level must be VDD + 0.3 V. Positive Power Supply Input. Specified range of operation: 2.7 V to 5.5 V. Table 4. AD5556 Pin Function Descriptions Pin No. 1 to 6 7 to 8 9 Mnemonic D5 to D0 NC ROFS 10 11 12 RFB R1 RCOM Description Digital Input Data Bits[D5:D0]. The signal level must be VDD+0.3 V. No Connection. The user should not connect anything other than dummy pads on these terminals. Bipolar Offset Resistor. Accepts up to 18 V. In two-quadrant mode, ties to RFB. In four-quadrant mode, ties to R1 and the external reference. Internal Matching Feedback Resistor. Connects to the output of an external op amp for I-V conversion. Four-Quadrant Resistor R1. In two-quadrant mode, shorts to the REF pin. In four-quadrant mode, ties to ROFS. Center Tap Point of Two Four-Quadrant Resistors, R1 and R2. In four-quadrant mode, ties to the inverting node of the reference amplifier. In two-quadrant mode, shorts to the REF pin. Rev. D | Page 6 of 20 Data Sheet Pin No. 13 Mnemonic REF 14 15 16 IOUT LDAC WR 17 MSB 18 RS 19 20 to 27 28 GND D13 to D6 VDD AD5546/AD5556 Description DAC Reference Input in Two-Quadrant Mode and R2 Terminal in Four-Quadrant Mode. In two-quadrant mode, this pin is the reference input with constant input resistance vs. code. In four-quadrant mode, this pin is driven by the external reference amplifier. DAC Current Output. Connects to the inverting node of an external op amp for I-V conversion. Digital Input Load DAC Control. The signal level must be VDD + 0.3 V. Write Control Digital Input in Active Low. Transfers shift-register data to the DAC register on the rising edge. The signal level must be VDD + 0.3 V. Power On Reset State. MSB = 0 resets at zero scale; MSB = 1 resets at midscale. The signal level must be VDD + 0.3 V. Reset in Active Low. Resets to zero scale if MSB = 0 and resets to midscale if MSB = 1. The signal level must be VDD + 0.3 V. Analog and Digital Grounds. Digital Input Data Bits[D13:D6]. The signal level must be VDD + 0.3 V. Positive Power Supply Input. Specified range of operation: 2.7 V to 5.5 V. Rev. D | Page 7 of 20 AD5546/AD5556 Data Sheet 1.0 0.8 0.8 0.6 0.6 0.4 0.4 0.2 0.2 0 -0.2 0 -0.2 -0.4 -0.4 -0.6 -0.6 -0.8 0 8192 -0.8 -1.0 16,384 24,576 32,768 40,960 49,152 57,344 65,536 CODE (Decimal) 0 8192 10,240 12,288 14,336 16,384 1.5 VREF = 2.5V TA = 25C 0.8 1.0 LINEARITY ERROR (LSB) 0.6 0.4 DNL (LSB) 6144 Figure 9. AD5556 Differential Nonlinearity Error 1.0 0.2 0 -0.2 -0.4 -0.6 0.5 INL 0 DNL -0.5 -1.0 GE 03810-007 -0.8 0 8192 -1.5 16,384 24,576 32,768 40,960 49,152 57,344 65,536 CODE (Decimal) 2 4 Figure 7. AD5546 Differential Nonlinearity Error 6 8 SUPPLY VOLTAGE VDD (V) 10 Figure 10. Linearity Error vs. VDD 1.0 5 VDD = 5V TA = 25C 0.8 0.4 0.2 0 -0.2 -0.4 03810-008 -0.6 -0.8 -1.0 0 2048 4096 4 3 2 1 0 6144 8192 10,240 12,288 14,336 16,384 CODE (Decimal) 03810-011 SUPPLY CURRENT IDD (LSB) 0.6 INL (LSB) 4096 CODE (Decimal) Figure 6. AD5546 Integral Nonlinearity Error -1.0 0248 03810-010 -1.0 03810-009 DNL (LSB) 1.0 03810-006 INL (LSB) TYPICAL PERFORMANCE CHARACTERISTICS 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 LOGIC INPUT VOLTAGE VIH (V) Figure 11. Supply Current vs. Logic Input Voltage Figure 8. AD5556 Integral Nonlinearity Error Rev. D | Page 8 of 20 5.0 Data Sheet AD5546/AD5556 3.0 -3.80 -3.85 -3.90 2.0 -3.95 0x5555 VOUT (V) SUPPLY CURRENT (mA) 2.5 1.5 0x8000 -4.00 -4.05 1.0 0xFFFF 0x0000 -4.10 0.5 100k 1M 10M -4.20 -200 100M 03810-115 03810-012 0 10k -4.15 -100 CLOCK FREQUENCY (Hz) 0 100 200 300 400 TIME (ns) Figure 12. AD5546 Supply Current vs. Clock Frequency Figure 15. AD5546 Midscale Transition 2 90 VDD = 5V 10% VREF = 10V 80 0 -2 70 -4 GAIN (dB) 50 40 30 -8 -10 -12 20 10 100 1k 10k FREQUENCY (Hz) 100k 1M -16 -18 10k 2 VOUT M 200ns 1M 10M 100M Figure 16. AD5546 Unipolar Reference Multiplying Bandwidth LDAC CH1 5.00V CH2 2.00V 100k FREQUENCY (Hz) Figure 13. Power Supply Rejection Ratio vs. Frequency 1 03810-116 03810-013 -14 10 0 -6 A CH1 2.70V B CH1 -6.20V 400.00ns 03810-014 PSRR (-dB) 60 Figure 14. Settling Time from Full Scale to Zero Scale Rev. D | Page 9 of 20 AD5546/AD5556 Data Sheet CIRCUIT OPERATION variation of the AD5546/AD5556 output impedance. The feedback resistance in parallel with the DAC ladder resistance dominates output voltage noise. To maintain good analog performance, it is recommended to bypass the power supply with a 0.01 F to 0.1 F ceramic or chip capacitor in parallel with a 1 F tantalum capacitor. Also, to minimize gain error, PCB metal traces between VREF and RFB should match. DIGITAL-TO-ANALOG (DAC) CONVERTER SECTION The AD5546/AD5556 are 16-/14-bit multiplying, current output, and parallel input DACs. The devices operate from a single 2.7 V to 5.5 V supply and provide both unipolar 0 V to -VREF, or 0 V to +VREF, and bipolar VREF output ranges from a -18 V to +18 V reference. In addition to the precision conversion RFB commonly found in current output DACs, there are three additional precision resistors for four-quadrant bipolar applications. Every code change of the DAC corresponds to a step function; gain peaking at each output step may occur if the op amp has limited GBP and excessive parasitic capacitance present at the op amp inverting node. A compensation capacitor, therefore, may be needed between the I-V op amp inverting and output nodes to smooth the step transition. Such a compensation capacitor should be found empirically, but a 20 pF capacitor is generally adequate for the compensation. The AD5546/AD5556 consist of two groups of precision R-2R ladders, which make up the 12/10 LSBs, respectively. Furthermore, the four MSBs are decoded into 15 segments of resistor value 2R. Figure 17 shows the architecture of the 16-bit AD5546. Each of the 16 segments in the R-2R ladder carries an equally weighted current of one-sixteenth of full scale. The feedback resistor, RFB, and four-quadrant resistor, ROFS, have values of 10 k. Each four-quadrant resistor, R1 and R2, equals 5 k. In four-quadrant operation, R1, R2, and an external op amp work together to invert the reference voltage and apply it to the REF input. With ROFS and RFB connected as shown in Figure 2, the output can swing from -VREF to +VREF. The VDD power is used primarily by the internal logic and to drive the DAC switches. Note that the output precision degrades if the operating voltage falls below the specified voltage. The user should also avoid using switching regulators because device power supply rejection degrades at higher frequencies. The reference voltage inputs exhibit a constant input resistance of 5 k 20%. The DAC output, IOUT, impedance is code dependent. External amplifier choice should take into account the REF 2R 80k R2 5k 2R 80k 2R 80k R1 5k 4 MSB 15 SEGMENTS R1 R 40k R 40k R 40k R 40k R 40k R 40k R 40k R 40k 2R 80k 2R 80k 2R 80k 2R 80k 2R 80k 2R 80k 2R 80k 2R 80k 2R 80k 8-BIT R-2R RA R R R R RB 2R 80k 2R 80k 2R 80k 2R 80k ROFS RFB 2R 80k 10k 10k 4-BIT R-2R IOUT GND 16 8 4 ADDRESS DECODER LDAC WR LDAC WR D15 DAC REGISTER RS INPUT REGISTER RS D14 RS D0 Figure 17. 16-Bit AD5546 Equivalent R-2R DAC Circuit with Digital Section Rev. D | Page 10 of 20 03810-019 RCOM 2R 80k Data Sheet AD5546/AD5556 DIGITAL SECTION The AD5546/AD5556 have 16-/14-bit parallel inputs. The devices are double buffered with 16-/14-bit registers. The double-buffered feature allows the update of several AD5546/AD5556 simultaneously. For the AD5546, the input register is loaded directly from a 16-bit controller bus when the WR pin is brought low. The DAC register is updated with data from the input register when LDAC is brought high. Updating the DAC register updates the DAC output with the new data (see Figure 17). To make both registers transparent, tie WR low and LDAC high. The asynchronous RS pin resets the part to zero scale if the MSB pin = 0 and to midscale if the MSB pin = 1. Table 5. AD5546 Parallel Input Data Format MSB B15 D15 Bit Position Data Word B14 D14 B13 D13 B12 D12 B11 D11 B10 D10 B9 D9 B8 D8 B7 D7 B6 D6 B5 D5 B4 D4 B3 D3 B2 D2 B1 D1 LSB B0 D0 Table 6. AD5556 Parallel Input Data Format MSB B13 D13 Bit Position Data Word B12 D12 B11 D11 B10 D10 B9 D9 B8 D8 B7 D7 B6 D6 B5 D5 B4 D4 B3 D3 B2 D2 B1 D1 LSB B0 D0 Table 7. Control Inputs RS 0 1 1 1 1 WR X1 0 1 0 LDAC Register Operation X 0 1 1 1 1 0 Reset output to 0, with MSB pin = 0 and to midscale with MSB pin = 1. Load input register with data bits. Load DAC register with the contents of the input register. Input and DAC registers are transparent. When LDAC and WR are tied together and programmed as a pulse, the data bits are loaded into the input register on the falling edge of the pulse and then loaded into the DAC register on the rising edge of the pulse. No register operation. 1 1 X = don't care. ESD PROTECTION CIRCUITS are good candidates for the I-V conversion. All logic input pins contain back-biased ESD protection Zeners connected to ground (GND) and VDD, as shown in Figure 18. As a result, the voltage level of the logic input should not be greater than the supply voltage. REFERENCE SELECTION VDD 5k DGND The voltage reference temperature coefficient (TC) and longterm drift are primary considerations. For example, a 5 V reference with a TC of 5 ppm/oC means that the output changes by 25 V per degree Celsius. As a result, the reference that operates at 55oC contributes an additional 750 V full-scale error. 03810-020 DIGITAL INPUTS The initial accuracy and the rated output of the voltage reference determine the full span adjustment. The initial accuracy is usually a secondary concern in precision because it can be trimmed. Figure 23 shows an example of a trimming circuit. The zero scale error can also be minimized by standard op amp nulling techniques. Figure 18. Equivalent ESD Protection Circuits AMPLIFIER SELECTION In addition to offset voltage, the bias current is important in op amp selection for precision current output DACs. An input bias current of 30 nA in the op amp contributes to 1 LSB in the AD5546's full-scale error. The OP1177 and AD8628 op amps Similarly, the same 5 V reference with a 50 ppm long-term drift means that the output may change by 250 V over time. Therefore, it is practical to calibrate a system periodically to maintain its optimum precision. Rev. D | Page 11 of 20 AD5546/AD5556 Data Sheet APPLICATIONS INFORMATION UNIPOLAR MODE Two-Quadrant Multiplying Mode, VOUT = 0 V to +VREF Two-Quadrant Multiplying Mode, VOUT = 0 V to -VREF The AD5546/AD5556 DAC architecture uses a current-steering R-2R ladder design that requires an external reference and op amp to convert the unipolar mode of output voltage to The AD5546/AD5556 are designed to operate with either positive or negative reference voltages. As a result, positive output can be achieved with an additional op amp, (see Figure 20), and the output becomes AD5546 AD5546 VOUT = -VREF x D/65,536 VOUT = +VREF x D/65,536 (1) (3) AD5556 AD5556 VOUT = -VREF x D/16,384 VOUT = +VREF x D/16,384 (2) (4) where D is the decimal equivalent of the input code. Table 9 shows the positive output vs. code for the AD5546. The output voltage polarity is opposite to the VREF polarity in this case (see Figure 19). Table 8 shows the negative output vs. code for the AD5546. Table 9. AD5546 Unipolar Mode Positive Output vs. Code D in Binary 1111 1111 1111 1111 1000 0000 0000 0000 0000 0000 0000 0001 0000 0000 0000 0000 Table 8. AD5546 Unipolar Mode Negative Output vs. Code D in Binary 1111 1111 1111 1111 1000 0000 0000 0000 0000 0000 0000 0001 0000 0000 0000 0000 VOUT (V) -VREF(65,535/65,536) -VREF/2 -VREF(1/65,536) 0 VOUT (V) +VREF(65,535/65,536) +VREF/2 +VREF(1/65,536) 0 +5V 2 C2 0.1F VIN U3 ADR03 TRIM 5 VOUT GND 4 R1 RCOM R1 REF R2 ROFS ROFS RFB C6 2.2pF RFB VDD C3 0.1F IOUT 16-/14-BIT DATA U1 AD5546/AD5556 V+ U2 AD8628 GND 16-/14-BIT DATA WR LDAC RS - + V- VOUT -2.5V TO 0V C4 0.1F MSB WR LDAC RS MSB -5V Figure 19. Unipolar Two-Quadrant Multiplying Mode, VOUT = 0 to -VREF Rev. D | Page 12 of 20 C5 1F 03810-021 C1 1F Data Sheet AD5546/AD5556 + U2A OP2177 - +10V C7 -10V RCOMA R1A VREFA ROFSA RFBA +15V C4 1F C6 +5V ROFS R2 R1 RFB VDD C2 0.1F IOUT 16-/14-BIT DATA U1 - AD5546/AD5556 C5 0.1F V+ U2B VOUT OP2177 GND + 16-/14-BIT DATA V- C8 1F WR LDAC RS MSB WR LDAC RS MSB C9 0.1F 03810-024 C1 1F -15V Figure 20. Unipolar Two-Quadrant Multiplying Mode, VOUT = 0 to +VREF 5V 2 + VIN U2A OP2177 U3 ADR03 TRIM VOUT GND 4 - 5 C1 6 R1 REF RCOM R1 5V -VREF +VREF ROFS ROFS R2 RFB RFB C2 VDD IOUT 16-/14-BIT DATA U1 AD5546/AD5556 U2B OP2177 16-/14-BIT DATA GND WR LDAC RS - + VOUT -VREF TO +VREF MSB 03810-002 WR LDAC RS MSB Figure 21. Four-Quadrant Multiplying Mode, VOUT = -VREF to +VREF BIPOLAR MODE Four-Quadrant Multiplying Mode, VOUT = -VREF to +VREF The AD5546/AD5556 contain on-chip all the four-quadrant resistors necessary for the precision bipolar multiplying operation. Such a feature minimizes the number of exponent components to only a voltage reference, dual op amp, and compensation capacitor (see Figure 21). For example, with a 10 V reference, the circuit yields a precision, bipolar -10 V to +10 V output. AD5546 VOUT = (D/32768 - 1) x VREF (5) AD5556 VOUT = (D/16384 - 1) x VREF Table 10 shows some of the results for the 16-bit AD5546. Rev. D | Page 13 of 20 (6) AD5546/AD5556 Data Sheet ac reference signals for signal attenuation, channel equalization, and waveform generation applications. The maximum signal range can be up to 18 V (see Figure 22). Table 10. AD5546 Output vs. Code D in Binary 1111 1111 1111 1111 1000 0000 0000 0001 1000 0000 0000 0000 0111 1111 1111 1111 0000 0000 0000 0000 VOUT +VREF(32,767/32,768) +VREF(1/32,768) 0 -VREF(1/32,768) -VREF SYSTEM CALIBRATION The initial accuracy of the system can be adjusted by trimming the voltage reference ADR0x with a digital potentiometer (see Figure 23). The AD5170 provides an OTP (one time programmable), 8-bit adjustment that is ideal and reliable for such calibration. The Analog Devices, Inc., OTP digital potentiometer comes with programmable software that simplifies the factory calibration process. AC REFERENCE SIGNAL ATTENUATOR Besides handling digital waveforms decoded from parallel input data, the AD5546/AD5556 handle equally well low frequency + U2A OP2177 - +10V C7 -10V R1A RCOMA ROFSA VREFA RFBA +15V C4 1F C6 R1 +5V R2 ROFS RFB VDD C2 0.1F IOUT 16/14-BIT U1 - AD5546/AD5556 C5 0.1F V+ U2B OP2177 GND + 16/14 DATA VOUT V- C8 1F WR LDAC RS MSB WR LDAC RS MSB C9 0.1F 03810-0-024 C1 1F -15V Figure 22. Signal Attenuator with AC Reference +5V 2 C2 0.1F + VIN U4 U3 ADR03 TRIM VOUT 5 R3 470k 6 GND 4 AD5170 V+ U2A AD8628 - 10k V- B R7 1k -5V +2.5V R1A C8 0.1F C9 1F -2.5V C7 RCOMA VREFA ROFSA RFBA +5V C6 R1 R2 ROFS VDD C3 0.1F U1 AD5546/AD5556 IOUT 16-/14-BIT DATA 16-/14-BIT DATA - C5 0.1F V+ U2B AD8628 GND WR LDAC RS C4 1F RFB + V- VOUT 0V TO +2.5V MSB WR LDAC RS MSB 03810-025 C1 1F Figure 23. Full Span Calibration Rev. D | Page 14 of 20 Data Sheet AD5546/AD5556 REFERENCE SELECTION When selecting a reference for use with the AD55xx series of current output DACs, pay attention to the output voltage temperature coefficient specification of the reference. Choosing a precision reference with a low output temperature coefficient minimizes error sources. Table 11 lists some of the references available from Analog Devices that are suitable for use with this range of current output DACs. AMPLIFIER SELECTION The primary requirement for the current-steering mode is an amplifier with low input bias currents and low input offset voltage. Because of the code-dependent output resistance of the DAC, the input offset voltage of an op amp is multiplied by the variable gain of the circuit. A change in this noise gain between two adjacent digital fractions produces a step change in the output voltage due to the amplifier's input offset voltage. This output voltage change is superimposed on the desired change in output between the two codes and gives rise to a differential linearity error, which, if large enough, can cause the DAC to be nonmonotonic. The input bias current of an op amp also generates an offset at the voltage output because of the bias current flowing in the feedback resistor, RFB. Common-mode rejection of the op amp is important in voltageswitching circuits because it produces a code-dependent error at the voltage output of the circuit. Provided that the DAC switches are driven from true wideband low impedance sources, they settle quickly. Consequently, the slew rate and settling time of a voltage-switching DAC circuit is determined largely by the output op amp. To obtain minimum settling time in this configuration, minimize capacitance at the VREF node (the voltage output node in this application) of the DAC. This is done by using low input capacitance buffer amplifiers and careful board design. Analog Devices offers a wide range of amplifiers for both precision dc and ac applications, as listed in Table 12 and Table 13. Table 11. Suitable Analog Devices Precision References Part No. ADR01 ADR01 ADR02 ADR02 ADR03 ADR03 ADR06 ADR06 ADR420 ADR421 ADR423 ADR425 ADR431 ADR435 ADR391 ADR395 Output Voltage (V) 10 10 5.0 5.0 2.5 2.5 3.0 3.0 2.048 2.50 3.00 5.00 2.500 5.000 2.5 5.0 Initial Tolerance (%) 0.05 0.05 0.06 0.06 0.1 0.1 0.1 0.1 0.05 0.04 0.04 0.04 0.04 0.04 0.16 0.10 Maximum Temperature Drift (ppm/C) 3 9 3 9 3 9 3 9 3 3 3 3 3 3 9 9 Rev. D | Page 15 of 20 ISS (mA) 1 1 1 1 1 1 1 1 0.5 0.5 0.5 0.5 0.8 0.8 0.12 0.12 Output Noise (V p-p) 20 20 10 10 6 6 10 10 1.75 1.75 2 3.4 3.5 8 5 8 Package(s) SOIC-8 TSOT-5, SC70-5 SOIC-8 TSOT-5, SC70-5 SOIC-8 TSOT-5, SC70-5 SOIC-8 TSOT-5, SC70-5 SOIC-8, MSOP-8 SOIC-8, MSOP-8 SOIC-8, MSOP-8 SOIC-8, MSOP-8 SOIC-8, MSOP-8 SOIC-8, MSOP-8 TSOT-5 TSOT-5 AD5546/AD5556 Data Sheet Table 12. Suitable Analog Devices Precision Op Amps Part No. OP97 OP1177 AD8675 AD8671 ADA4004-1 AD8603 AD8607 AD8605 AD8615 AD8616 Supply Voltage (V) 2 to 20 2.5 to 15 5 to 18 5 to 15 5 to 15 1.8 to 5 1.8 to 5 2.7 to 5 2.7 to 5 2.7 to 5 VOS Maximum (V) 25 60 75 75 125 50 50 65 65 65 IB Maximum (nA) 0.1 2 2 12 90 0.001 0.001 0.001 0.001 0.001 0.1 Hz to 10 Hz Noise (V p-p) 0.5 0.4 0.1 0.077 0.1 2.3 2.3 2.3 2.4 2.4 Supply Current (A) 600 500 2300 3000 2000 40 40 1000 2000 2000 Package(s) SOIC-8 , PDIP-8 MSOP-8, SOIC-8 MSOP-8, SOIC-8 MSOP-8, SOIC-8 SOIC-8, SOT-23-5 TSOT-5 MSOP-8, SOIC-8 WLCSP-5, SOT-23-5 TSOT-23-5 MSOP-8, SOIC-8 Table 13. Suitable Analog Devices High Speed Op Amps Part No. AD8065 AD8066 AD8021 AD8038 ADA4899-1 AD8057 AD8058 AD8061 AD8062 AD9631 Supply Voltage (V) 5 to 24 5 to 24 5 to 24 3 to 12 5 to 12 3 to 12 3 to 12 2.7 to 8 2.7 to 8 3 to 6 BW @ ACL (MHz) 145 145 490 350 600 325 325 320 320 320 Slew Rate (V/s) 180 180 120 425 310 1000 850 650 650 1300 Rev. D | Page 16 of 20 VOS (Max) (V) 1500 1500 1000 3000 35 5000 5000 6000 6000 10,000 IB (Max) (nA) 0.006 0.006 10,500 750 100 500 500 350 350 7000 Package(s) SOIC-8, SOT-23-5 SOIC-8, MSOP-8 SOIC-8, MSOP-8 SOIC-8, SC70-5 LFCSP-8, SOIC-8 SOT-23-5, SOIC-8 SOIC-8, MSOP-8 SOT-23-5, SOIC-8 SOIC-8, MSOP-8 SOIC-8, PDIP-8 Data Sheet AD5546/AD5556 OUTLINE DIMENSIONS 9.80 9.70 9.60 28 15 4.50 4.40 4.30 6.40 BSC 1 14 PIN 1 0.65 BSC 0.15 0.05 COPLANARITY 0.10 0.30 0.19 1.20 MAX SEATING PLANE 0.20 0.09 8 0 0.75 0.60 0.45 COMPLIANT TO JEDEC STANDARDS MO-153-AE Figure 24. 28-Lead Thin Shrink Small Outline Package [TSSOP] RU-28 Dimensions shown in millimeters ORDERING GUIDE Model1 AD5546BRU AD5546BRU-REEL7 AD5546BRUZ AD5546BRUZ-REEL7 AD5546CRUZ AD5546CRUZ-REEL7 AD5556CRU AD5556CRU-REEL7 AD5556CRUZ EVAL-AD5546SDZ 1 RES (Bit) 16 16 16 16 16 16 14 14 14 DNL (LSB) 1 1 1 1 1 1 1 1 1 INL (LSB) 2 2 2 2 1 1 1 1 1 Temperature Range (C) -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 Package Description 28-Lead TSSOP 28-Lead TSSOP 28-Lead TSSOP 28-Lead TSSOP 28-Lead TSSOP 28-Lead TSSOP 28-Lead TSSOP 28-Lead TSSOP 28-Lead TSSOP Evaluation Board Z = RoHS Compliant Part. Rev. D | Page 17 of 20 Package Option RU-28 RU-28 RU-28 RU-28 RU-28 RU-28 RU-28 RU-28 RU-28 Ordering Quantity 50 1,000 50 1,000 50 1,000 50 1,000 50 AD5546/AD5556 Data Sheet NOTES Rev. D | Page 18 of 20 Data Sheet AD5546/AD5556 NOTES Rev. D | Page 19 of 20 AD5546/AD5556 Data Sheet NOTES (c)2004-2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D03810-0-11/11(D) Rev. D | Page 20 of 20