STA1052 DSP/MCU system for CD-DA, CD-CA, CD-ROM player Data Brief Features CD-R, CD-RW playback Audio decoding (MP3,WMA,AAC) CLV (1x, 2x, 4x) and CAV mode (6x) On-chip USB-OTG host full speed 3.3 V 5 % operating supply range for I/O 1.8 V 5 % operating supply range for logic IDLE, WFI and STOP modes Power on reset / Brownout controller 33.8688 MHz external quartz/resonator Operating temperature range: -40 C to +85 C LQFP144 (20x20x1.4 mm) Acquisition 32 bit MCU with 3-stage pipeline @ 67 MHz 384 KB internal ROM (4 Mb on package RAM for development version) and 128 KB RAM Full range adjustment-free digital PLL EFM demodulation and synchronization Q subcode and CD text decoder Error correction Embedded ARM7TDMI microcontroller CIRC, capable of dual C1, quad C2 erasure RSPC capable of C3 corrections Jitter absorbing capacity 24 frames (CLV) Shock-proof controller 2 I C master/slave (400 kHz) + 1 CRQ line Up to 64 Mbit external SDRAM interface Two high-speed UART full-duplex 8/16 bit data bus interface Two buffered SPI master/slave interface ADPCM (4:1) lossy compression for extended shock proof capability Analog Front-end part A, B, C, D, E, F voltage inputs Audio features Automatic gain and offset control Two I2S transmitters and one I2S receiver ALPC circuit with integrated Power MOS SPDIF transmitter (IEC958) and receiver 8 bit 2 channels general purpose ADC Sample-rate conversion from 8 kHz - 48 kHz input to 44.1 kHz output Digital servo Digital equalizer for bass/treble control Automatic fine gain/balance/offset adjustment for tracking and focus Built-in stereo DAC Embedded 16 bit servo DSP (33.8688 MHz) Development environment PDM controls for focus, tracking, spindle, sledge Embedded stepping sledge motor controller CLV & CAV spindle control March 2008 5 pin JTAG port (IEEE 1149.1 standard) Table 1. Rev 1 For further information contact your local STMicroelectronics sales office. Device summary Order code Package Packing STA1052S1 LQFP144 Tray 1/14 www.st.com 14 Contents STA1052 Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 System block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1 Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.2 Pin function description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2/14 STA1052 1 Description Description The STA1052 is a single chip device which performs all functions related to read back of optical disk: servo control operations, reading optical disc decoding the High frequency signals, EFM decoding, error correction, software decoding of MP3 and WMA encoded audio, sample rate conversion, managing file system, serial transfer of audio/program through I2S/SPDIF, direct playback of audio through in-built audio DAC. It also performs software decoding of MP3, AAC and WMA encoded audio from USB or SD cardTM memory supports. Commands can be exchanged with the Host MCU either via one I2C port or two SPI ports. STA1052 chip comes along a broad software suite that comprehends different types of compressed audio files, File System Management, Play Lists. The key Media and File Types supported are briefly reported below: Ability to play any USB/SD card compatible solid state memory media MPEG1-Layer 2 compressed audio files Playback of MP3 compressed audio files (all bit rates and VBR) Playback of lower bit rate MPEG2 layer 3 files and MPEG-2.5 extension Playback of WMA version 9 compressed audio files Playback of iTunes AAC compressed audio files Sample rate converter for recorded sampling rates other than 44.1kHz Support FAT16/FAT32 file systems Support ISO9660 and Joliet file systems The software can manage the following File Information: folder and file names. ID3 tag information - as per versions 1.0-1.1, 2.0 - 2.4- is reported. Further parameters made available by ST software are: File type (i.e. .mp3, .wav, .wma, .cda, .aac), Bit rate, entire file path for current track and track elapsed time. STA1052 software provides the essential Navigation Commands: Previous/Next , Fast forward/Rewind, Jump to any file, Scan, Pause. All these commands can be programmed and configured via Command Protocol Interface. Two different types of Playlists are supported: Playlists with .pls extension, Playlists with .m3u extension. Robust software architecture provides an efficient error handling and related messaging. ST developed a software architecture that allows the patching of a few parts of software resident in ROM. Software patches are loaded into a very inexpensive serial Flash which provides the capability to patch up to 40 KByte of ROM software. Software build (patching) upgrade from media USB and SD card and from host MCU onto serial Flash is supported. STA1052 is intended for use in automotive entertainment system. 3/14 4/14 + Track Loop filter Focus Loop filter SLED Loop filter DSP Focus Actuator Track Actuator Sled Motor Spindle Motor Spindle Motor Feedback (CAV) defect FE TE JumpSpeed 1.7Kx32 PRAM 256x16 XRAM 256x16 YRAM PDM/ stepper AHB ITF Ext Mem External Interrupt ARM Subsystem AUDIO L/R out F RATE + DECIM. TrackCount Frame Org Obs/Debug fade/ mute/ deemph master clock Quartz/ Ceramic PLL DAC ANALOG filter E B+D A+C A+C B+D E F DeScram + RSPC ADPCM Encoder I/V OFFSET GAIN ADC CLV buffer Output interface A B C D E F AUX ADC Sub code decoder Cross Interleaving Reed-Solomon ADPCM Decoder ADC2 Digital PLL Sync protection & EFM demodulator Figure 1. ADC1 Laser control digital equalizer 2 LD MD SDRAM Interface System block diagram STA1052 System block diagram Figure 1 provides the complete system block diagram, where the ARM sub-system is represented as a hierarchical block. STA1052 block diagram SPDIF-SONYLSI-I2S Application interface STA1052 Pin description 3 Pin description 3.1 Pin connection NC JTCK JTRST DRBA1 DRBA0 DRA11 DRA10 DRA9 DRA8 DRA7 DRA6 DRA5 VDD VSS VDD3 DRA4 DRA3 DRA2 DRA1 DRA0 DRWR DRCAS DRRAS DRCLKE DRCLK VSS VDD3_Core1 DRD15 DRD14 DRD13 DRD12 GPB9 GPB10 GPB11 DRD11 LQFP144 pin configuration (top view) DRD10 Figure 2. 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 DRD9 1 108 OUTR DRD8 2 107 ADAC_REF1 GPB12 3 106 VCM GPB13 4 105 ADAC_REF2 GPB14 5 104 OUTL GPB15 6 103 ADAC_VDDA DRD7 7 102 ADAC_VSSA DRD6 8 101 VSS DRD5 9 100 VDD3 VDD 10 99 JTMS VSS 11 98 JTDO VDD3 12 97 JTDI DRD4 13 96 GPB7 DRD3 14 95 GPB6 DRD2 15 94 VDD DRD1 16 93 GPB8 DRD0 17 92 GPB5 PLL_VSS18P 18 91 GPB4 PLL_VDDA33P 19 90 GPB3 PLL_XTI 20 89 GPB2 PLL_XTO 21 88 GPB1 PLL_VDDA18P 22 87 VDD3_Core2 PLL_VDD18P 23 86 VSS FE_VSSA33S 24 85 GPB0 FE_A 25 84 GPA8 FE_C 26 83 GPA7 FE_B 27 82 GPA6 FE_D 28 81 GPA5 FE_E 29 80 GPA4 FE_F 30 79 GPA13 FE_VDDA33S 31 78 GPA3 FE_VDDPAD1 32 77 GPA2 FE_ADCIN1 33 76 GPA1 FE_ADCIN2 34 75 NC FE_VREF_ADC 35 74 NC FE_VREF 36 73 NC GPA0 BCLK SDO GPA12 GPA11 GPA10 GPA9 LRCK CAV TFSR VDD3 VSS VDD SLED2 SLED1 SPDL REFFSR FFSR TESTEN RESETN VSS FE_VSSA18AD FE_VDDA18AD FE_VSSA33T FE_TESTN FE_TESTP FE_VDDA33T FE_VDDPAD2 FE_LD1_LAS FE_LD_LAS FE_CAP_LAS FE_MD_LAS FE_VSSA33R FE_REXT FE_CEXT FE_VDDA33R 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 AC00563 1. NC defines not connected pins. 5/14 Pin description 3.2 STA1052 Pin function description This pin list contains the definition and description of all pins. Table 2 gives pin list for LQFP144. Table 2. Pin List N Name Description Pin type LQFP144 1 GPC9(DRD9) GPIO PC9 (SDRAM data 9) bidir, 3.3V , 4 mA 1 2 GPC8(DRD8) GPIO PC8 (SDRAM data 8) bidir, 3.3 V, 4 mA 2 3 GPB12 GPIO PB12(BSPI1_SS) bidir, 3.3 V, 2 mA, PU (default off) 3 4 GPB13 GPIO PB13 (BSPI1_MISO) bidir, 3.3 V, 2 mA, PU (default off) 4 5 GPB14 GPIO PB14 (BSPI1_MOSI) bidir, 3.3 V, 2 mA, PU (default off) 5 6 GPB15 GPIO PB15 (BSPI1_SCK) bidir, 3.3 V, 2 mA, PU (default off) 6 7 GPC7(DRD7) GPIO PC7 (SDRAM data 7) bidir, 3.3 V, 4 mA 7 8 GPC6(DRD6) GPIO PC6 (SDRAM data 6) bidir, 3.3 V, 4 mA 8 9 GPC5(DRD5) GPIO PC5 (SDRAM data 5) bidir, 3.3 V, 4 mA 9 10 VDD Core VDD1.8 V VDD 10 11 VSS Digital pad ring VSS ground VSS 11 12 VDD3 Digital pad ring VDD3 3.3 V VDD3 12 13 GPC4(DRD4) GPIO PC4 (SDRAM data 4) bidir, 3.3 V, 4 mA 13 14 GPC3(DRD3) GPIO PC3 (SDRAM data 3) bidir, 3.3 V, 4 mA 14 15 GPC2(DRD2/ SFLASH_MISO) GPIO PC2 (SDRAM data 2 or serial flash master in/slave out) bidir, 3.3 V, 4 mA 15 16 GPC1(DRD1/ SFLASH_MOSI) GPIO PC1 (SDRAM Data 1 or serial flash master out/slave in) bidir, 3.3 V, 4 mA 16 17 GPC0(DRD0/ SFLASH_SCK) GPIO PC0 (SDRAM data 0 or serial Flash clock) bidir, 3.3 V, 4 mA 17 18 PLL_VSS18P PLL digital & analog ground VSS 18 19 PLL_VDDA33P PLL 3.3 analog power supply VDD 19 20 PLL_XTI Crystal input analog in 20 21 PLL_XTO Crystal output analog out 21 22 PLL_VDDA18P PLL 1.8V analog power supply VDD 22 23 PLL_VDD18P PLL 1.8V digital power supply VDD 23 24 FE_VSSA33S Ground for servo channels VSS 24 25 FE_A OPU A input analog in 25 26 FE_C OPU C input analog in 26 6/14 STA1052 Table 2. Pin description Pin List (continued) N Name Description Pin type LQFP144 27 FE_B OPU B input analog in 27 28 FE_D OPU D input analog in 28 29 FE_E OPU E input analog in 29 30 FE_F OPU F input analog in 30 31 FE_VDDA33S 3.3 V analog for servo channels/ 3.3 V for AFE pad ring (decoupling cap to Vssa) VDD 31 32 FE_VDDPAD1 3.3V for AFE pad ring VDD 32 33 FE_ADCIN1 General purpose ADC input 1 analog in 33 34 FE_ADCIN2 General purpose ADC input 2 analog in 34 35 FE_VREF_ADC General purpose ADC Vtop reference output analog out 35 36 FE_VREF External Vref pickup (decoupling cap 1 nF) analog out 36 37 FE_VDDA33R Analog 3.3 V for bandgap VDD 37 38 FE_CEXT External cap for bandgap (1 nF) analog 38 39 FE_REXT External res for bandgap (25 kOhm) analog 39 40 FE_VSSA33R Analog ground bandgap Vss 40 41 FE_MD_LAS Laser driver input from monitor diode analog in 41 42 FE_CAP_LAS Laser driver compensation cap (30 nF) analog 42 43 FE_LD_LAS First laser driver output analog out 43 44 FE_LD1_LAS Second laser driver output analog out 44 45 FE_VDDPAD2 3.3 V for AFE pad ring VDD 45 46 FE_VDDA33T Analog 3.3 V for test buffer VDD 46 47 FE_TESTP Test buffer positive output analog out 47 48 FE_TESTN Test buffer negative output analog out 48 49 FE_VSSA33T Analog ground test buffer VSS 49 50 FE_VDDA18AD Analog 1.8 V ADC VDD 50 51 FE_VSSA18AD Analog ground ADC VSS 51 52 VSS Core VSS ground VSS 52 53 RESETN Hardware reset input (pull-up) in, schmitt, 3.3 V 53 54 TESTEN Test enable signal (active low) in, 3.3V 54 55 FFSR Focusing actuator control signal output Out, 3.3 V, 4 mA PDM 55 56 REFFSR Clock (50% duty cycle) for actuator PDM reference 56 Out, 3.3 V, 2 mA 7/14 Pin description Table 2. STA1052 Pin List (continued) N Name Description Pin type LQFP144 57 SPDL Spindle motor control signal output PDM Out, 3.3 V, 2 mA 57 58 SLED1 SLED motor control signal output1 (stepping/DC) - PDM Out, 3.3 V, 2 mA 58 59 SLED2 SLED motor control signal output2 (stepping) -PDM Out, 3.3 V, 2 mA 59 60 VDD Core VDD 1.8 V VDD 60 61 VSS Digital pad ring VSS ground VSS 61 62 VDD3 Digital pad ring VDD3 3.3 V VDD3 62 63 TFSR Tracking actuator control signal output Out, 3.3 V, 4 mA PDM 63 64 CAV CAV feedback input in, 3.3 V 64 65 LRCK Serial L/R clock bidir, 3.3 V, 2 mA 65 66 GPA9 GPA9 (I2S1_Tx_SCK (SCK1)) bidir, 3.3 V, 2 mA, PU (default off) 66 67 GPA10 GPA10 (I2S1_Tx_WCK (SC12)) bidir, 3.3 V, 2 mA, PU (default off) 67 68 GPA11 GPA11 (I2S1_Tx_SDO (STD1)) bidir, 3.3 V, mA, PU (default off) 68 69 GPA12 GPA12 (I2S1_ref_CK) bidir, 3.3 V, 2 mA, PU (default off) 69 70 SDO/SPDIF Serial bit data or SPDIF Digital output bidir, 3.3 V, 2 mA 70 71 BCLK Serial bit clock bidir, 3.3 V, 2 mA 71 72 GPA0 (EINT0) GPIO PA0 (external interrupt 0/timer 0 output 0) bidir, 3.3 V, 2 mA, PU (default off) 72 - NC Not connected 73 - NC Not connected 74 - NC Not connected 75 73 GPA1 (EINT1) GPIO PA1 (external interrupt 1/timer 0 output 1) bidir, 3.3 V, 2 mA, PU (default off) 76 74 GPA2 (EINT2) GPIO PA2 (external interrupt 2/timer 1 output 0) bidir, 3.3 V, 2 mA, PU (default off) 77 75 GPA3 (EINT3) GPIO PA3 (external interrupt 3/timer 1 output1 ) bidir, 3.3 V, 2 mA, PU (default off) 78 76 GPA13 GPIO PA13 (SPDIF Rx) bidir, 3.3 V, 2 mA, PU (default off) 79 77 GPA4 (EINT4) GPIO PA4 (external interrupt 4) bidir, 3.3 V, 2 mA, PU (default off) 80 78 GPA5 (EINT5) GPIO PA5 (external interrupt 5) bidir, 3.3 , 2 mA, PU (default off) 81 8/14 STA1052 Table 2. N Pin description Pin List (continued) Name Description Pin type LQFP144 79 GPA6 (EINT6) GPIO PA6 (external interrupt 6) bidir, 3.3 V, 2 mA, PU (default off) 82 80 GPA7 (EINT7) GPIO PA7 (external interrupt 7) bidir, 3.3 V, 2 mA, PU (default off) 83 81 GPA8 (EINT8) GPIO PA8 (external interrupt 8) bidir, 3.3 V, 2 mA, PU (default off) 84 82 GPB0/SFLASH_SS (EINT9) GPIO PB0 or serial Flash slave select (external interrupt 9) bidir, 3.3 V, 2 mA, PU (default off) 85 83 VSS Digital pad ring VSS ground Vss 86 84 VDD3_Core2 Digital pad ring VDD3 3.3 V VDD3 87 85 GPB1/I2C_CRQ (EINT10) GPIO PB1 or I2C CRQ line (external interrupt 10) bidir, 5 V tol, 2 mA(sink) 88 86 GPB2/I2C_SCL (EINT11) GPIO PB2 or I2C I/F clock (external interrupt 11) bidir, 5 V tol, 2 mA(sink) 89 87 GPB3/I2C_SDA (EINT12) GPIO PB3 or I2C I/F data (external interrupt 12) bidir, 5 V tol, 2 mA(sink) 90 88 GPB4/SCI0TX GPIO PB4 or serial interface 0 TX or EXTCK_OIF bidir, 3.3 V, 2mA, PU (default off) 91 89 GPB5/SCI0RX (EINT13) GPIO PB5 or serial interface 0 RX (external interrupt 13) bidir, 3.3V, 2mA, PU (default off) 92 90 GPB8/C2PO/USBCK GPIO PB8 or C2PO (EIAJ CP-340) or USB clock line (48 MHz) bidir, 3.3V, 2mA, PU (default off) 93 91 VDD Core VDD 1.8 V VDD 94 92 GPB6/SCI1TX/USBDM GPIO PB6 or serial interface 1 TX or USB D- line bidir, 3.3 V, 2 mA, PU (default off)(1) USB pad (Full / Low speed ) 95 93 GPB7/SCI1RX/USBDP (EINT14) GPIO PB7 or serial interface 1 RX or USB D+ line (external interrupt 14) bidir, 3.3 V, 2 mA, PU (default off)(1) USB pad (Full / Low speed ) 96 94 JTDI JTAG test data input in, 3.3V 97 95 JTDO JTAG test data output out, 3.3 V, 2 mA 98 96 JTMS JTAG test mode select input in, 3.3 V 99 97 VDD3 Digital pad ring VDD3 3.3 V VDD3 100 98 VSS Digital pad ring VSS ground Vss 101 99 ADAC_VSSA Audio DAC ground VSSDAC 102 100 ADAC_VDDA Audio DAC supply 3.3 V VDDDAC 103 101 OUTL Left channel analog output analog out 104 102 ADAC_REF2 Audio DAC VLO (GND) analog in 105 9/14 Pin description Table 2. STA1052 Pin List (continued) N Name Description Pin type LQFP144 103 VCM Common Mode input for audio DAC (1.65 V) analog in 106 104 ADAC_REF1 Audio DAC VHI (3.3 V) analog in 107 105 OUTR Right channel analog output analog out 108 - NC Not Connected 109 106 JTCK JTAG test clock input in, 3.3 V 110 107 JTRST JTAG test reset input in, schmitt, 3.3 V 111 108 DRBA1 SDRAM bank sel address 1 out, 3.3 V, 4 mA 112 109 DRBA0/CFG4 SDRAM bank sel address 0 and configuration bit 4 (latched at reset) bidir, 3.3 V, 4 mA 113 110 DRA11/CFG3 SDRAM address 11 and configuration bit 3 (latched at reset) bidir, 3.3V, 4mA 114 111 DRA10/CFG2 SDRAM Address 10 and configuration bit 2 (latched at reset) bidir, 3.3 V, 4 mA 115 112 DRA9/CFG1 SDRAM Address 9 and configuration bit 1 bidir, 3.3 V, 4 mA (latched at reset) 116 113 DRA8/CFG0 SDRAM Address 8 and configuration bit 0 bidir, 3.3 V, 4 mA (latched at reset) 117 114 DRA7 SDRAM address 7 out, 3.3 V, 4 mA 118 115 DRA6 SDRAM address 6 out, 3.3 V, 4 mA 119 116 DRA5 SDRAM address 5 out, 3.3 V, 4 mA 120 117 VDD Core VDD 1.8 V VDD 121 118 VSS Digital pad ring VSS ground VSS 122 119 VDD3 Digital pad ring VDD3 3.3 V VDD3 123 120 DRA4 SDRAM address 4 out, 3.3 V, 4 mA 124 121 DRA3 SDRAM address 3 out, 3.3 V, 4 mA 125 122 DRA2 SDRAM address 2 out, 3.3 V, 4 mA 126 123 DRA1 SDRAM address 1 out, 3.3 V, 4 mA 127 124 DRA0 SDRAM address 0 out, 3.3 V, 4 mA 128 125 DRWR SDRAM write control out, 3.3 V, 4 mA 129 126 DRCAS SDRAM col address sel out, 3.3 V, 4 mA 130 127 DRRAS SDRAM row address sel out, 3.3 V, 4 mA 131 128 DRCLKE SDRAM CLK enable out, 3.3 V, 4 mA 132 129 DRCLK SDRAM CLK out, 3.3 V, 4 mA 133 10/14 STA1052 Table 2. Pin description Pin List (continued) N Name Description Pin type LQFP144 130 VSS Digital pad ring VSS ground VSS 134 131 VDD3_Core1 Digital pad ring VDD3 3.3 V VDD3 135 132 GPC15 (DRD15) GPIO PC15 (SDRAM Data 15) bidir, 3.3 V, 4 mA 136 133 GPC14 (DRD14) GPIO PC14 (SDRAM Data 14) bidir, 3.3 V, 4 mA 137 134 GPC13 (DRD13) GPIO PC13 (SDRAM Data 13) bidir, 3.3 V, 4 mA 138 135 GPC12 (DRD12) GPIO PC12 (SDRAM Data 12) bidir, 3.3 V, 4 mA 139 136 GPB9 GPB9 (I2S1_Rx_SCK (SC10)) bidir, 3.3 V, 2 mA, PU (default off) 140 137 GPB10 GPB10 (I2S1_Rx_WCK (SC11)) bidir, 3.3V, 2mA, PU (default off) 141 138 GPB11 GPB11 (I2S1_Rx_SDI (SRD1)) bidir, 3.3 V, 2 mA, PU (default off) 142 139 GPC11 (DRD11) GPIO PC11 (SDRAM Data 11) bidir, 3.3 V, 4 mA 143 140 GPC10 (DRD10) GPIO PC10 (SDRAM Data 10) bidir, 3.3V , 4 mA 144 1. The specifications in USB mode are as per USB specifications for low and full speed interface. 11/14 Package information 4 STA1052 Package information In order to meet environmental requirements, ST (also) offers these devices in ECOPACK(R) packages. ECOPACK(R) packages are lead-free. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. Figure 3. LQFP144 (20x20x1.4mm) mechanical data and package dimensions mm inch DIM. MIN. TYP. A MAX. MIN. TYP. MAX. 1.600 0.0630 0.150 0.0020 0.0059 A1 0.050 A2 1.350 1.400 1.450 0.0531 0.0551 0.0571 b 0.170 0.220 0.270 0.0067 0.0087 0.0106 c 0.090 D 21.800 22.000 22.200 0.8583 0.8661 0.8740 D1 19.800 20.000 20.200 0.7795 0.7874 0.7953 D3 0.200 0.0035 17.500 0.0079 0.6890 E 21.800 22.000 22.200 0.8583 0.8661 0.8740 E1 19.800 20.000 20.200 0.7795 0.7874 0.7953 E3 17.500 0.6890 e 0.500 0.0197 L L1 k ccc 0.450 0.600 OUTLINE AND MECHANICAL DATA 0.750 0.0177 0.0236 0.0295 1.000 0.0394 LQFP144 (20x20x1.40mm) Low profile plastic Quad Flat Package 0(min.), 3.5(typ.), 7(max.) 0.080 0.0031 Note 1: Exact shape of each corner is optional. 0099183 C 12/14 STA1052 5 Revision history Revision history Table 3. Document revision history Date Revision 12-Mar-2008 1 Changes Initial release. 13/14 STA1052 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 14/14