Caution Although this device is designed to be as robust as possible, ESD (Electrostatic
Discharge) can damage this device. This device must be protected at all times from ESD. Static
charges may easily produce potentials of several kilovolts on the human body or equipment, which
can discharge without detection. Industry-standard ESD precautions must be employed at all times.
HIGH POWER SPDT SWITCH FOR WiMAXTM
GaAs INTEGRATED CIRCUIT
PG2409T6X
Document No. PG10773EJ01V0DS (1st edition)
Date Published July 2009 NS
DESCRIPTION
The
PG2409T6X is a GaAs MMIC high power SPDT (Single Pole Double Throw) switch which were designed for
WiMAX.
This device can operate frequency from 0.05 to 6.0 GHz, having the low insertion loss and high isolation.
This device is housed in a 6-pin plastic TSON (Thin Small Out-line Non-leaded) (T6X) package. And this
package is suitable for high-density surface mounting.
FEATURES
•Switch control voltage : Vcont (H) = 3.0 V TYP.
: Vcont (L) = 0 V TYP.
•Low insertion loss : Lins = 0.45 dB TYP. @ f = 2.5 GHz
: Lins = 0.55 dB TYP. @ f = 3.8 GHz
: Lins = 0.65 dB TYP. @ f = 6.0 GHz
•High isolation : ISL = 30 dB TYP. @ f = 2.5 GHz
: ISL = 30 dB TYP. @ f = 3.8 GHz
: ISL = 27 dB TYP. @ f = 6.0 GHz
•Handling power : Pin (1 dB) = +36.0 dBm TYP. @ f = 0.05 to 6.0 GHz
•High-density surface mounting : 6-pin plastic TSON (T6X) package (1.5 1.5 0.37 mm)
APPLICATIONS
•WiMAX and wireless LAN (IEEE802.11a/b/g/n)
ORDERING INFORMATION
Part Number
Order Number
Package
Marking
Supplying Form
PG2409T6X-E2
PG2409T6X-E2-A
6-pin plastic TSON
(T6X) (Pb-Free)
G5R
Embossed tape 8 mm wide
Pin 1, 6 face the perforation side of the tape
Qty 3 kpcs/reel
Remark To order evaluation samples, please contact your nearby sales office.
Part number for sample order:
PG2409T6X-A
DISCONTINUED
Drop-In Replacement: CG2409X3
Data Sheet PG10773EJ01V0DS
PG2409T6X
PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM
Pin No.
Pin Name
1
RF1
2
GND
3
RF2
4
Vcont2
5
RFC
6
Vcont1
Remark Exposed pad :
GND
SW TRUTH TABLE
Vcont1
Vcont2
RFC-RF1
RFC-RF2
High
Low
ON
OFF
Low
High
OFF
ON
ABSOLUTE MAXIMUM RATINGS (TA = +25C, unless otherwise specified)
Parameter
Symbol
Ratings
Unit
Switch Control Voltage
Vcont
+6.0 Note
V
Input Power
Pin
+36
dBm
Operating Ambient Temperature
TA
45 to +85
C
Storage Temperature
Tstg
55 to +150
C
Note Vcont1 Vcont2 6.0 V
RECOMMENDED OPERATING RANGE (TA = +25C, unless otherwise specified)
Parameter
Symbol
MIN.
TYP.
MAX.
Unit
Operating Frequency
f
0.05
6.0
GHz
Switch Control Voltage (H)
Vcont (H)
2.7
3.0
3.3
V
Switch Control Voltage (L)
Vcont (L)
0.2
0
0.2
V
Control Voltage Difference
Vcont (H),
Vcont (L)Note
0.1
0
0.1
V
Note
Vcont (H) = Vcont1 (H) Vcont2 (H)
Vcont (L) = Vcont1 (L) Vcont2 (L)
DISCONTINUED
Drop-In Replacement: CG2409X3
Data Sheet PG10773EJ01V0DS
3
PG2409T6X
ELECTRICAL CHARACTERISTICS
(TA = +25C, Vcont (H) = 3.0 V, Vcont (L) = 0 V, ZO = 50 , DC blocking capacitors = 8 pF, unless
otherwise specified)
Parameter
Symbol
Test Conditions
MIN.
TYP.
MAX.
Unit
Insertion Loss 1
Lins1
f = 0.05 to 0.5 GHz Note 1
0.35
dB
Insertion Loss 2
Lins2
f = 0.5 to 2.0 GHz Note 2
0.40
0.65
dB
Insertion Loss 3
Lins3
f = 2.0 to 2.5 GHz
0.45
0.70
dB
Insertion Loss 4
Lins4
f = 2.5 to 3.8 GHz
0.55
0.80
dB
Insertion Loss 5
Lins5
f = 3.8 to 6.0 GHz
0.65
0.90
dB
Isolation 1
ISL1
f = 0.05 to 0.5 GHz Note 1
30
dB
Isolation 2
ISL2
f = 0.5 to 2.0 GHz Note 2
25
30
dB
Isolation 3
ISL3
f = 2.0 to 2.5 GHz
25
30
dB
Isolation 4
ISL4
f = 2.5 to 3.8 GHz
25
30
dB
Isolation 5
ISL5
f = 3.8 to 6.0 GHz
22
27
dB
Return Loss 1
RL1
f = 0.05 to 0.5 GHz Note 1
20
dB
Return Loss 2
RL2
f = 0.5 to 2.0 GHz Note 2
15
20
dB
Return Loss 3
RL3
f = 2.0 to 2.5 GHz
15
20
dB
Return Loss 4
RL4
f = 2.5 to 6.0 GHz
10
15
dB
0.1 dB Loss Compression
Pin (0.1 dB)
f = 0.5 to 6.0 GHz Note 2
+34.0
dBm
Input Power Note 3
1 dB Loss Compression
Input Power Note 4
Pin (1 dB)
f = 0.05 to 0.5 GHz Note 1
+36.0
dBm
f = 0.5 to 6.0 GHz Note 2
+34.0
+36.0
dBm
2nd Harmonics
2f0
f = 2.5 GHz, Pin = +30 dBm
70
dBc
3rd Harmonics
3f0
f = 2.5 GHz, Pin = +30 dBm
70
dBc
Input 3rd Order Intercept Point
IIP3
f = 2.5 GHz
+60
dBm
Switch Control Current
Icont
No RF input
0.1
10
A
Switch Control Speed
tSW
50% CTL to 90/10% RF
100
250
ns
Notes 1. DC blocking capacitors = 1 000 pF at f = 0.05 to 0.5 GHz
2. DC blocking capacitors = 56 pF at f = 0.5 to 2.0 GHz
3. Pin (0.1 dB) is the measured input power level when the insertion loss increases 0.1 dB more than that of
the linear range.
4. Pin (1 dB) is the measured input power level when the insertion loss increases 1 dB more than that of the
linear range.
Caution It is necessary to use DC blocking capacitors with this device.
DISCONTINUED
Drop-In Replacement: CG2409X3
Data Sheet PG10773EJ01V0DS
PG2409T6X
EVALUATION CIRCUIT
Note C1 : 0.05 to 0.5 GHz 1 000 pF
: 0.5 to 2.0 GHz 56 pF
: 2.0 to 6.0 GHz 8 pF
The application circuits and their parameters are for reference only and are not intended for use in actual design-ins.
APPLICATION INFORMATION
• C1 are DC blocking capacitors external to the device.
The value may be tailored to provide specific electrical responses.
• The RF ground connections should be kept as short as possible and connected to directly to a good RF ground
for best performance.
• LESD provides a means to increase the ESD protection on a specific RF port, typically the port attached to the
antenna.
DISCONTINUED
Drop-In Replacement: CG2409X3
Data Sheet PG10773EJ01V0DS
5
PG2409T6X
TYPICAL CHARACTERISTICS (
T
A
= +25
C, DC blocking capacitors = 8 pF, unless otherwise specified
)
Remark The graphs indicate nominal characteristics.
DISCONTINUED
Drop-In Replacement: CG2409X3
Data Sheet PG10773EJ01V0DS
PG2409T6X
Remark The graphs indicate nominal characteristics.
DISCONTINUED
Drop-In Replacement: CG2409X3
Data Sheet PG10773EJ01V0DS
7
PG2409T6X
MOUNTING PAD AND SOLDER MASK LAYOUT DIMENSIONS
6-PIN PLASTIC TSON (UNIT: mm)
Remark The mounting pad and solder mask layouts in this document is for reference only.
When designing PCB, please consider workability of mounting, solder joint reliability, prevention of
solder bridge and so on, in order to optimize the design.
DISCONTINUED
Drop-In Replacement: CG2409X3
Data Sheet PG10773EJ01V0DS
PG2409T6X
PACKAGE DIMENSIONS
6-PIN PLASTIC TSON (T6X) (UNIT: mm)
DISCONTINUED
Drop-In Replacement: CG2409X3
Data Sheet PG10773EJ01V0DS
9
PG2409T6X
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered and mounted under the following recommended conditions. For soldering
methods and conditions other than those recommended below, contact your nearby sales office.
Soldering Method
Soldering Conditions
Condition Symbol
Infrared Reflow
Peak temperature (package surface temperature) : 260C or below
Time at peak temperature : 10 seconds or less
Time at temperature of 220C or higher : 60 seconds or less
Preheating time at 120 to 180C : 12030 seconds
Maximum number of reflow processes : 3 times
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
IR260
Partial Heating
Peak temperature (terminal temperature) : 350C or below
Soldering time (per side of device) : 3 seconds or less
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
HS350
Caution Do not use different soldering methods together (except for partial heating).
DISCONTINUED
Drop-In Replacement: CG2409X3
10 Data Sheet PG10773EJ01V0DS
PG2409T6X
Caution GaAs Products
This product uses gallium arsenide (GaAs).
GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the
following points.
• Follow related laws and ordinances when disposing of the product. If there are no applicable laws
and/or ordinances, dispose of the product as recommended below.
1. Commission a disposal company able to (with a license to) collect, transport and dispose of
materials that contain arsenic and other such industrial waste materials.
2. Exclude the product from general industrial waste and household garbage, and ensure that the
product is controlled (as industrial waste subject to special control) up until final disposal.
• Do not burn, destroy, cut, crush, or chemically dissolve the product.
• Do not lick the product or in any way allow it to enter the mouth.
DISCONTINUED
Drop-In Replacement: CG2409X3
NOTICE
1. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and
application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. California
Eastern Laboratories and Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits,
software, or information.
2. California Eastern Laboratories has used reasonable care in preparing the information included in this document, but California Eastern Laboratories does
not warrant that such information is error free. California Eastern Laboratories and Renesas Electronics assumes no liability whatsoever for any damages
incurred by you resulting from errors in or omissions from the information included herein.
3. California Eastern Laboratories and Renesas Electronics do not assume any liability for infringement of patents, copyrights, or other intellectual property
rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express,
implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of California Eastern Laboratories or Renesas
Electronics or others.
4. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. California Eastern
Laboratories and Renesas Electronics assume no responsibility for any losses incurred by you or third parties arising from such alteration, modication, copy
or otherwise misappropriation of Renesas Electronics product.
5. Renesas Electronics products are classied according to the following two quality grades: “Standard” and “High Quality”. The recommended applications
for each Renesas Electronics product depends on the product’s quality grade, as indicated below. “Standard”: Computers; ofce equipment; communications
equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and
industrial robots etc. “High Quality”: Transportation equipment (automobiles, trains, ships, etc.); trafc control systems; anti-disaster systems; anti-crime
systems; and safety equipment etc. Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct
threat to human life or bodily injury (articial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear
reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it in a particular
application. You may not use any Renesas Electronics product for any application for which it is not intended. California Eastern Laboratories and Renesas
Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product
for which the product is not intended by California Eastern Laboratories or Renesas Electronics.
6. You should use the Renesas Electronics products described in this document within the range specied by California Eastern Laboratories, especially with
respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product
characteristics. California Eastern Laboratories shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products
beyond such specied ranges.
7. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specic characteristics such as
the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation
resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by
re in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy,
re control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of
microcomputer software alone is very difcult, please evaluate the safety of the nal products or systems manufactured by you.
8. Please contact a California Eastern Laboratories sales ofce for details as to environmental matters such as the environmental compatibility of each Renesas
Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of
controlled substances, including without limitation, the EU RoHS Directive. California Eastern Laboratories and Renesas Electronics assume no liability for
damages or losses occurring as a result of your noncompliance with applicable laws and regulations.
9. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited
under any applicable domestic or foreign laws or regulations. You should not use Renesas Electronics products or technology described in this document
for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. When
exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and
regulations and follow the procedures required by such laws and regulations.
10. It is the responsibility of the buyer or distributor of California Eastern Laboratories, who distributes, disposes of, or otherwise places the Renesas Electronics
product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, California Eastern Laboratories and
Renesas Electronics assume no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products.
11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of California Eastern Laboratories.
12. Please contact a California Eastern Laboratories sales ofce if you have any questions regarding the information contained in this document or Renesas
Electronics products, or if you have any other inquiries.
NOTE 1: “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.
NOTE 2: “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.
NOTE 3: Products and product information are subject to change without notice.
CEL Headquarters • 4590 Patrick Henry Drive, Santa Clara, CA 95054 • Phone (408) 919-2500 • www.cel.com
For a complete list of sales ofces, representatives and distributors,
Please visit our website: www.cel.com/contactus
DISCONTINUED
Drop-In Replacement: CG2409X3
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
CEL:
UPG2409T6X-A UPG2409T6X-E2-A UPG2409T6X-EVAL-A