LCD Module Technical Specification First Edition May. 02, 2007 Final Revision Apr. 10, 2012 ten. 1-51750GD065J-FW-AFN Customer : STANDARD Customer's Product NO : =#="""---- KYOCERA Display Corporation Toshiyuki Okamoto Approved: QUALITY ASSURANCE DIVISION Checked: Masayuki Kato Design Div, Prepared: Hironori Miyano Design Div. Table of Contents 4 I 0121 =| es) OL 101] 1 0r> 1 00) 8 1 3 2. Electrical specifications .. 2.02.0... .0 00.0. e cece eee ete ceca ete cee ee geenes eee eeessenees 4 x Ha @) 0) (0r= | Bes) 61-07) | (07-11 (0) 0 | 12 4. WO Terminal.............0 00. cece cece nee nee cece e ence eee ee ees e deca ecnedeeeeegeeseseesesseeeeneens 17 5. TOSE oe ce cece eee ee eee ee eee ee Eee ead ene dees dee esa eee snes ee nessa eae saeaaeaeeeeeeeenenees 19 6. Appearance Standards. ............. cece cece cece cece cence nee ec nec eee ec eedeeeecnedeeseeneeeeeeeseeneeneneens 20 7. Code System of Production LOt ...............c cece cee cee eee eee eee eee ee eeeeee eee eeeeaeeeeeeeaeeeeeeeeeeenenees 23 rs Ra AY] OL = L010 0] 2) A 23 9. Applying Precautions ........ 0... eee ee eee ee eee eee ence nec eee eee eceeeeteceeneeneenereeeees 23 10. Precautions Relating Product Handling. ............. ccc cccccccecseeececeeeeeeeeseeneseseaeeseseseeeeenees 24 11. Warranty. 22.00. e nee eee cence eee c eee eeeeceedeeeeceeceegeegeseeeeesesseseeneens 26 T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 1/26Revision History Rev. Date Page Comment 1 May 9, 2008 24~26 Revise of Precautions Relating Product Handling and Warranty. 2 Apr. 10. 2012 - Changing companys name T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 2/261. General Specifications Operating Temperature Storage Temperature Resolution Dot pitch Pixel arrangement Color depth Active Viewing Area Outline dimensions * Weight LCD type Viewing angle Interface Backlight * Surface Treatment Drawings RoHS regulation : min. -25 deg. to max. 75 deg.(*Note) : min. -25 deg. to max. 85 deg. : 640 x 3 [R.G.B] (W) x 480 (H) dots : 0.069 x 3 [R.G.B] (W) x 0.207 (V) mm : RGB-Stripe : 262,144 colors - 132.5 (W) x 99.4 (H) mm : 158.0 (WW) x 120.36 (H) x 10.75 (D) mm * Excluding backlight cables. : 190 g typ. : Normally white-mode / Transmissive : 6:00 : 18-bit parallel data transfer (6-bit / color) : CCFL, Edge lighting type 2-tubes, replaceable * Backlight driving DC/AC inverter is not built in this module. : AR Coating : Dimensional Outline T-51750 AF base B To our best knowledge, this product satisfies material requirement of RoHS regulation. Our company is doing the best efforts to obtain the equivalent certificate from our suppliers. Note : Operation temperature range defines the operation only. Electrical and optical specification can be guaranteed at the condition that ambient temperature is 25C. T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 3/262. Electrical specifications 2.1. Absolute Maximum Ratings Parameter Symbol Conditions Min. Max. Unit Supply Voltage for LCD VCC - 0 5.5 V Logic Input Voltage Vi - 0 5.5 V 2.2. DC characteristics (1) TFT-LCD Ambient Temperature : Ta = 25C ITEM SYMBOL] MIN. TYP. MAX. UNIT Remarks Power Supply Voltages forLCD] 6g 3.0 3.3 3.6 V for 3.3V system Note A) 45 5.0 5.5 V for 5V system Power Supply Currents for LCD icc - 240 - mA for 3.3V system Note B) - 180 -- mA for 5V system -- -- 100 mVp-p VOC=+3.3V Permissive input ripple Voltage VRP -- -- 100 mVp-p VCC=+5.0V High VIH 2.4 - 5.5 V VCC=MAX Logic Input Voltage Low VIL 0 -- 0.8 V VCC=MIN [Note] A) VCC-dip conditions: 1) When 2.4 V < VCC < 3.0 V, td < 10 ms 2) When VCC <2.4V VCC-dip conditions should also follow the power and signals sequence. Vcc > Ww ~ 3 > o | B) Typical current condition: 64- gray- bar-pattern 480 line mode VCC = +3.3 V, fy=31.5kHz, fy=60HZz, foLKk= 25MHz VCC = +5.0 V, f4=31.5kHz, fy=60HZ, forKk= 25MHz T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 4/262.3. AC Characteristic ITEM SYMBOL MIN. TYP. MAX. UNIT Frequency foik 20 25 30 MHz Period tok 33.3 40 50 ns DCLK Low Width twet 10 -- -- ns High Width tweu 10 -- -- ns DATA Set up time tos 5 -- -- ns (R,G,B,DENA, HD, VD) Hold time tou 5 -- -- ns Horizontal Active Time tHa 640 640 640 tok Horizontal Front Porch ture 0 -- -- tok Horizontal Back Porch tuep 7 -- -- tok DENA Vertical Active Time tva 480 480 480 tu Vertical Front Porch tvep 1 20 -- ty Vertical Back Porch tvsp 8 20 -- ty Frequency fu 27 31.5 38 kHz HD Period ty 26.3 31.7 37.0 US Low Width twu 5 -- 7 teLk Frequency fy 55 60 70 Hz VD Period ty 14.3 16.7 18.2 ms Low Width twvL 3 -- -- ty [Note] 1) DATA is latched at fall edge of DCLK in this timing specification. 2) Polarities of HD and VD are negative in this specification. 3) DENA (Data Enable) should always be positive polarity as shown in the timing specification. 4) DCLK should appear during all invalid period, and HD should appear during invalid period of frame cycle. 5) Accepted only 640 data and 480 lines. 6) REV should be stable during operation. T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 5/267) Please consider the influenece of the filter circuit which is placed in the Signal Input, DCLK and Data Bus, when designing the circuit. AC Characteristic spec is based on ideal signal driving. BK1005LL241-T BK1005LL241-T (TAIYO YUDEN) (TAIYO YUDEN) [sex>!f])\o- Timig converter CLK Timig converter VSYNC, RGB signal > ait Data BK1005LL241-T or BK32164L241-T (TAIYO YUDEN) T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 6/262.4. Timing Chart a. Pixel Timing Chart DCLK DATA(R,G.B), DENA, HD, VD tok b. Horizontal Timing Chart DCLK PLP Ly] LULA First Data FULL DATA (R,G,B) Invalid Data X DENA Last Data Invalid Data Y 1 2 ys Y ose e40 J xX I tuee tuBe tha \\ Ww ty=1/fu twa pd A v \\ HD c. Vertical Timing Chart HD LINE DATA VD Ww tw 4 <4 T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 7/262.5. Power and signals sequence: t1<10ms 200 ms < t6 0<t2<50ms 0<t7 Vcc 3.0V or 4.5V_/ 1 3.0V or 4.5V ; data \ '0.3V '/ 0.3V 0.3V 7 i t1 | t2 3 1t4' 5h tft Backlight. =f - at 6 t7 data: RGB DATA, DCLK, HD, VD, DENA 0<t3<50ms Q0<t4<50ms 500 ms <t5 2.6.Pixel Alignment T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 8/262.7. Color Data Assignment R DATA G DATA B DATA COLOR INPUT MSB LsB | MSB LSB |MSB LSB DATA R5} R4:/ RBERZ: R1: RO| GS! G4! G3! G2: 61: GO| BS: B4: B3 : B2 : B1 : BO BLACK 0:0:0:0:0:04/;0:0:0:0:0:0/0:0:0:0:0:0 RED (63) 1:74:7:7:51474:1/0:0:;0:0:;0:01/10:0:0:0:0:0 GREEN (63)/0:0:0:0:0:0/1:1:1:1:1:1/0!:0:0:0:0:0 BASIC |BLUE (63) 0:0:0:0:0:0;0:0:0:0:0:0/1:1:1:1:1:1 COLOR |CYAN 0:0:0:0:0:0)4;1:14:14:1:1:4/7/1:'51:51:1:1:1 MAGENTA 1:4:54:1:5141:1/0:0:;0:0,;0:;0/)/1:1:1:1:1:1 YELLOW 1272472 7:57:547/77575757'574517050:50:0:0:0 WHITE 1:74:5474:54:57:51474/7171:57:51451:51:514771:5171:51:5141:1:1 RED (0) 0:0:0:0:0:0;0:0:0:0:0:0/0:0:0:0:0:0 RED (1) 0:0:0:0:0:1/;0:0:0:0:0:0/0:0:0:0:0:0 RED (2) 0,-0:0:0:;1:0/;0:0:;0:0:0:0/0:0:0:0:0:0 RED RED (62) 1:4:47:41:1:0/0:0:;0:0:0:0/0:0:0:0:0:0 RED (63) 1:4:47:4:141:5:1/0:0:;0:0:0:0/0:0:0:0:0:0 GREEN (0) 0-0:0:0:;0:04/;0:0:;0:0:0:0/0:0:0:0:0:0 GREEN (1) 0:0:0:0:0:0/;0:0:0:0:0:1/0:0:0:0:0:0 GREEN (2) 0:-0:0:0:;0:0;0:0:0:0:1:0/0:0:0:0:0:0 GREEN GREEN (62)/0:0:0:0:0:0/1:1:1:1:1:0/0!:0:0:0:0:0 GREEN (63)/0:0:0:0:0:0/1:1:1:1:1:1/0:0:0:0:0:0 BLUE (0) 0:-0:0:0:;0:0/;0:0:0:0:0:0/0:0:0:0:0:0 BLUE (1) 0:0:0:0:0:04;0:0:0:0:0:0/0:0:0:0:0: 1 BLUE (2) 0:0:0:0:0:0/;0:0:0:0:0:0/0:0:0:0:1:0 BLUE BLUE (62) 1:1:1:1:1:0 BLUE (63) 0:0:0:0:0:0 O71:4:1:1:1:1 [Note] 1) Definition of gray scale Color (n) --- n indicates gray scale level. Higher n means brighter level. 2) Data 1:High, 0: Low T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 9/262.8. Inverted Scan Capability This module has the capability of inverting scan direction by signaling from controller. Note that scan direction cannot be changed during operation. The following figure shows the relation between the display position and the scan direction. DISPLAY POSITION Normal scan: REV = L D( 1, 1) D( 2, 1) --- D( X, 1) --- D(639, 1) | D640, 1) D( 1, 2) D( 2, 2) --- D( X, 2) --- D(639, 2) | D(640, 2) ! ! + + + ! ! D( 1, Y) D( 2, Y) --- D(X, Y) --- D(639, Y) | D640, Y) ! ! + + + ! ! D( 1,479) | D( 2,479) --- D( X,479) --- D(639,479) | D(640,479) D( 1,480) D( 2,480) --- DC X,480) --- D(639,480) | D(640,480) Reverse scan: REV = H D(640,480) | D(639,480) --- D( X,480) --- D( 2,480) | D( 1,480) D(640,479) | D(639,479) --- D( X,479) --- D( 2,479) | D 1,479) ! ! + + + ! ! D(640, Y) D(639, Y) --- D(X, Y) --- D( 2, Y) D( 1, Y) ! ! + + + ! ! D(640, 2) | D639, 2) --- D( X, 2) --- D( 2, 2) D( 1, 2) D(640, 1) D(639, 1) --- D( X, 1) --- D( 2, 1) D( 1, 1) The following drawing shows the relationship between the viewing direction and the scan direction. Normal scan D(1,1) = W> D640,1) aes D(1,480) _<"_, D(640,480) 1] i Reverse scan [7 a ss D(1,480) _<"_,, D(640,480) T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 10/262.9Lighting Specifications Ta=25C Parameter Symbol Conditions Min. Typ. Max. Units |Notes Lamp Voltage VL - - 320 - Vrms 1 Lamp Current IL - - 6.0 7.0 mArms 2 Starting Voltage Vs - - - 520 Vrms 3 Surface Luminance L IL=6mA - 4500 - cd/m? 4 Average Life TAL l1L=6mA 50,000 - - hrs 5 Note 1 :The voltage (r.m.s. ) to maintain the electric discharge of the lamp. It is measured after lighting for 3 minutes . Note 2 :The current (r.m.s. ) to flow through the lamp with the electric discharge. It is measured after lighting for 3 minutes. Note 3 :The voltage at starting the electric discharge when the voltage is increased gradually from OV. Note 4 :Surface Luminance is specified by the average of 9 luminance values measured at each point shown above after 20 minutes power on with the all ON pattern adjusted to maximum contrast and the dimming control of 100%. ( maximum brightness ) Note 5: CFL Life is defined as time period that the actual luminance becomes 50% or lower of its initial value. The Average life time of CFL is defined as the time when half or more of the testing CFLs have become less bright than 50% of the initial brightness at continuous operation. N I VL Vv UL CFL Testing Circuit 10 Y=60 Y=320 Y=580 Measurement Points Recommended Inverter : S-12645 ( Produced by ELEVAM ) T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 11/263. Optical Specifications Conditions Standard Value . Method of Item Symbol Unit Remark 8 b Cc Min. Typ. Max. Measure Brightness B o | oc - 400 - cd/m? Note3-1 Best Contrast CR Viewing 150 300 - - Rx o | o - 0.56 - - Red Ry ae | oe - 0.33 - - Gx o | o - 0.34 - - . Green (Fig.3-1) Color Gy o o - 0.53 = - Coordinates Bx o | O - 0.15 - - Blue By o | o - 0.14 - - Wx a | oe - 0.32 - - White Wy o | o - 0.32 - - Brightness Uniformity - oe |; o 0.7 - - - (Fig.3-2) Vertical Up Bu - o | >10 - 30 - Degree Viewing Angle] Down Op - o | >10 - 60 - Degree (Fig.3-3) Horizontal Left OL o - | 210 - 55 - Degree Viewing Angle] Right or oc | - | 210 - 55 - |Degree Response Rise wT o | o - 15 - ms ; (Fig.3-4) Time Decay td oe |; o - 16 - ms Note3-1:Under the condition of maximum brightness. @ Conditions for Measuring } Environment: Dark room with no light or close to no light. <} Temperature: 25+5C <& Humidity: 40~70%RH < After backlight has been lit more then 30 minutes, driving voltage is set for optimal contrast to measure center of display. < Measure by the specified inverter or similar product. Condition: IL=6.0 mA, FL=58 kHz @ Optimal viewing angle (The angle with best contrast) -T] TT 6 Oclock T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 12/26(Fig.3-1) @ Method of Brightness Measurement (1) Measuring Device TOPCON BM-7,Measuring Field:1 (2) Measuring Point Center of Display 9=0, 6=0 On condition 96: Avertical angle from measuring direction to perpendicular. : A horizontal angle from measuring direction to perpendicular. Center (Pixel) (X, Y)= (820, 240) LCD Module Distance -500mm TOPCON BM-7 (3) Method of Measuring Apply signal voltage (displayed in white) to maximize brightness and measure brightness B (cd/m). The distance between BM-7s front lens to surface panel is 500mm. Measured after backlight has been lit for more than 30 minutes. @ Method of Contrast Measurement (1) Measuring Device TOPCON BM-7,Measuring Field:1 (2) Measuring Point Center of display: same as Method of Brightness Measurement (3) Method of Measuring Set LCD module to0=0, =0. Change signal voltage to measure maximum brightness Y1 and minimum brightness Y2. Contrast is derived from CR=Y1/Y2. T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 13/26(Fig.3-2) @ Definition of Brightness Uniformity Definition is calculated from the 5 points (SO-S4) on the diagram below. 20mm 20mm a a , si So r s2 Standard Value of Brightness Uniformity= SO Minimum Value of $1-S4 } 20mm S4. + $s3. } 20mm T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 14/26(Fig.3-3) @ Method of Viewing Angle Measurement (1) Measuring Device TOPCON BM-7,Measuring Field:1 (2) Measuring Point Center of display : Same as Method of Brightness Measurement (3) Angle of Measuring 6: An angle vertical to perpendicular line from the viewing direction. o: An angle horizontal to perpendicular from the viewing direction. Temperature Rotation Table(9,o) TOPCON BM-7 | LCD A Soo L__] Computer Control Unit & Waveform Generator (4) Method of Measuring Set rotation table to =0 and set BM-7 to contrast 10 to measure angle+o for left and right direction of horizontal viewing angled. Also set rotation table to =90 and set BM-7 to contrast 10 to measure angle+ for up and down direction of vertical viewing angle 9. T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 15/26(Fig.3-4) @ Measuring Response Time (1) Measuring Device TOPCON BN-7,Measuring Field:1 Tektronix Digital Oscilloscope (2) Measuring Point Center of display, same as Method of Brightness Measurement (3) Method of Measuring * Set LCD panel to0=0,and $=0. * Input whiteblackwhite to display by switching signal voltage. - If the luminance is 0% and 100% immediately before the change of signal voltage, then tr is optical response time during the change from 90% to 10% immediately after rise of signal voltage, and td is optical response time during the change from 10% to 90% immediately after decay of signal voltage. White Black Whit 100% 90% Brightness 10% 0% TT Vv a (Fig.3-5) @ Image Sticking td v A Continuously display the test pattern shown in the figure below for two-hours. Then display a completely white screen. The previous image shall not persist more than two seconds at 25C. TEST PATTERN FOR IMAGE STICKING TEST i Rows 238-242 ; T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 16/264. 1/O Terminal 4.1 Pin assignment CN 1(INTERFACE SIGNAL) Used connector: DF9B-31P-1V (Hirose) Corresponding connector: DF9B-31S-1V (Hirose) Pin No. Symbol Function 1 GND 2 DCLK Clock signal for sampling catch data signal 3 HD Horizontal sync signal 4 VD Vertical sync signal 5 GND 6 RO Red data signal(LSB) 7 R1 Red data signal 8 R2 Red data signal 9 R3 Red data signal 10 R4 Red data signal 11 R5 Red data signal(MSB) 12 GND 13 GO Green data signal(LSB) 14 G1 Green data signal 15 G2 Green data signal 16 G3 Green data signal 17 G4 Green data signal 18 G5 Green data signal(MSB) 19 GND 20 BO Blue data signal(LSB) 21 B1 Blue data signal 22 B2 Blue data signal 23 B3 Blue data signal 24 B4 Blue data signal 25 B5 Blue data signal(MSB) 26 GND 27 DENA Data enable signal(to settle the viewing area) 28 vcc Power Supply (DC 3.3V or 5V) 29 VCC Power Supply (DC 3.3V or 5V) 30 TEST This pin should be open. Test signal output for only internal test use. 31 REV Reverse scan control. L = Normal, H = Reverse *) The shielding case is connected with GND CN 2, CN 3 (BACKLIGHT) Backlight-side connector: BHR-02(8.0)VS-1N(WJST) Inverter-side connector: SM02(8.0)B-BHS(JST) Pin No. Symbol Function 1 CTH VBLH(High Voltage) 2 CTL VBLL(Low Voltage) [Note] VBLH-VBLL = VL T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 17/264.2. Block Diagram BACKLIGHT CN2 Driver(source) Timing signal Display data S _ N Timing a | nN | = _> Converter 5 ~_|[oa,y Oo L w 5 @ Sy 8 o 2 2 TFT-LCD Power 8 oO zz > LL G480 BACKLIGHT CN3 BACKLIGHT CCFL CN2,CN3 T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 18/265. Test No abnormal function and appearance are found after the following tests. Conditions: Unless otherwise specified, tests will be conducted under the following condition. Temperature: 20+5C Humidity : 65+5%RH tests will be not conducted under functioning state. No. Parameter Conditions Notes 1 High Temperature Operating | 60C, 96hrs (operation state) 2 High Temperature Storage 85C, 96hrs 2 3 Low Temperature Storage -25C, 96hrs 1,2 4 Damp Proof Test 40C,90~95%RH, 96hrs 1,2 5 Vibration Test Frequency:10-57Hz/Vibration width(one side):0.75mm 3 :58-500Hz/Gravity:9.8m/s Sweep time:11minutes Test period:3hrs for each direction of X,Y,Z 6 Shock Shock level:490m/s Waveform:half sinusoidal wave, 11ms Number of shocks : One shock input in each direction of three mutually perpendicular axis for a total of six shock inputs 7 Shock Test To be measured after dropping from 60cm high on the concrete surface in packing state. Dropping method corner dropping | F Accorner : once E Edge d i Gg D c ge dropping | 7 B,C,D edge : once B A Face dropping {coon E,F,G face : once Concrete Surface Note 1: No dew condensation to be observed. Note 2: The function test shall be conducted after 4 hours storage at the normal Temperature and humidity after removed from the test chamber. Note 3: Vibration test will be conducted to the product itself without putting it in a container. T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 19/266. Appearance Standards 6.1.Inspection conditions The LCD shall be inspected under 40W white fluorescent light. The distance between the eyes and the sample shall be more than 30cm. All directions for inspecting the sample should be within 45against perpendicular line. 6.2.Definition of applicable Zones x Xx x fro fee cece ee cece eee eee esse erected Leen cece cee ece eect eeneneeeeeenes A Zone | B Zone yo pc de C Zone X%: Maximum Seal Line A Zone : Active display area B Zone: Out of active display area up to viewing area C Zone : Rest parts A Zone + B Zone = Viewing area T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 20/266.3 Standards No. Parameter Criteria Polarizer Scratches Zone Acceptable Number X(mm) Y(mm) A B Cc 1 L<15 |0.01<W<0.05 4 * L>15 W > 0.01 0 * - W > 0.05 0 * X : Length, Y : Width * : Disregard DENT Zone Acceptable Number > Dimension (mm) A B Cc 0.30 <D <0.50 4 * 0.50<D 0 * D : Average Diameter = (long+short)/2 * : Disregard BLACK and WHITE SPOT BUBBLE Zone Acceptable Number 3 Dimension (mm) A B Cc 0.30 <D<0.50 5 * 0.50<D 0 * LINT Zone Acceptable Number X(mm) Y(mm) A B Cc 4 L<3.0 W<0.15 4 * L>3.0 W <0.15 0 * - W>0.15 According to BLACK SPOT * X: Length, Y : Width * : Disregard T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 21/26No. Parameter Criteria (a) Bright Dot (b) Dark Dot Zone Acceptable Number Dimension (mm) A B Cc 5 Bright Dot 7(G<3) * Dark Dot 7 * TOTAL 10 6 TWO Adjacent Dot Zone Acceptable Number Dimension (mm) A B Cc Bright Dot 3 PAIRS * Dark Dot 3 PAIRS * 7 Three or More Adjacent Dot NOT ALLOWED 8 Zone Acceptable Number Dimension (mm A B Cc Bright Dot 5mm * Dark Dot 5mm * 9 Line Defect NOT ALLOWED Note 1: Bright Dot is defined as follows: Visible through 5% transmission ND filter under the condition that black image (color Q) is on the display. Note 2: Dark Dot is defined as follows: Recognizable darker than around under the condition that each R(63), G(63), B(63) image is on the display. Note 3: Definition of adjacent R;}/G/B;|R|G|B;/R/ G/B Defective Dot Adjacent Dots R}/G|B R eer! R;}/G|}B;|R|G|B;/R/ G/B The defects that are not defined above and considered to be problem shall be reviewed and discussed by both parties. T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 22/267. Code System of Production Lot The production lot of module is specified as follows. OOoOoOoOoO-ogdo | oL Factory Control Number (0~99) Pt of the week (A~G) Factory Number (0~9) Factory Code (Alphabet) Production Week (1~5) Production Month (1~9, X, Y, Z) Production Year (Lower 2 digits) 8. Type Number The type number of module is specified as follows. T-51750GDO065J-FW-AFN 9. Applying Precautions Please contact us when questions and/or new problems not specified in this Specifications arise. T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 23/2610. Precautions Relating Product Handling The Following precautions will guide you in handling our product correctly. 1) Liquid crystal display devices 1. The liquid crystal display panel used in the liquid crystal display module is made of plate glass. Avoid any strong mechanical shock. Should the glass break handle it with care. The polarizer AN adhering to the surface of the LCD is made of a soft material. Guard against scratching it. 2) Care of the liquid crystal display module against static electricity discharge. 1. When working with the module, be sure to ground your body and any electrical equipment you may be using. We strongly recommend the use of anti static mats (made of rubber), to protect worktables against the hazards of electrical shock. 2. Avoid the use of work clothing made of synthetic fibers. We recommend cotton clothing or other conductivity-treated fibers. 3. Slowly and carefully remove the protective film from the LCD module, since this operation can generate static electricity. 3) When the LCD module must be stored for long periods of time: 1.Protect the modules from high temperature and humidity. Conditions: Temperature: 0C~40C Humidity : Less than 60%RH No dew condensation to be observed. 2.Keep the modules out of direct sunlight or direct exposure to ultraviolet rays. 3.Protect the modules from excessive external forces. 4) Use the module with a power supply that is equipped with an overcurrent protector circuit, since the module is not provided with this protective feature. 5) Do not ingest the LCD fluid itself should it leak out of a damaged LCD module. Should hands or clothing come in contact with LCD fluid, wash immediately with soap. 6) Conductivity is not guaranteed for models that use metal holders where solder connections between the metal holder and the PCB are not used. Please contact us to discuss appropriate ways to assure conductivity. 7) For models which use CFL: 1.High voltage of 1000V or greater is applied to the CFL cable connector area. Care should be taken not to touch connection areas to avoid burns. 2.Protect CFL cables from rubbing against the unit and thus causing the wire jacket to become worn. 3.The use of CFLs for extended periods of time at low temperatures will significantly shorten their service life. 4.After storing the product (or LCD) under low temperature and/or in dark atmosphere for a long period of time, CCFL may take longer time to reach its specified brightness. 8) For models which use touch panels: 1.Do not stack up modules since they can be damaged by components on neighboring modules. 2.Do not place heavy objects on top of the product. This could cause glass breakage. T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 24/269) For models which use COG,TAB,or COF: 1.The mechanical strength of the product is low since the IC chip faces out unprotected from the rear. Be sure to protect the rear of the IC chip from external forces. 2.Given the fact that the rear of the IC chip is left exposed, in order to protect the unit from electrical damage, avoid installation configurations in which the rear of the IC chip runs the risk of making any electrical contact. 10)Models which use flexible cable, heat seal, or TAB: 1.In order to maintain reliability, do not touch or hold by the connector area. 2.Avoid any bending, pulling, or other excessive force, which can result in broken connections. 11)In case of buffer material such as cushion / gasket is assembled into LCD module, it may have an adverse effect on connecting parts (LCD panel-TCP / HEAT SEAL / FPC / etc., PCB-TCP / HEAT SEAL / FPC etc., TCP-HEAT SEAL, TCP-FPC, HEAT SEAL-FPC, etc.,) depending on its materials. Please check and evaluate these materials carefully before use. 12)In case of acrylic plate is attached to front side of LCD panel, cloudiness (very small cracks) can occur on acrylic plate, being influenced by some components generated from polarizer film. Please check and evaluate those acrylic materials carefully before use. T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 25/2611. Warranty This product has been manufactured to your companys specifications as a part for use in your companys general electronic products. It is guaranteed to perform according to delivery pecifications. For any other use apart from general electronic equipment, we cannot take responsibility if the product is used in medical devices, nuclear power control equipment, aerospace equipment, fire and security systems, or any other applications in which there is a direct risk to human life and where extremely high levels of reliability are required. If the product is to be used in any of the above applications, we will need to enter into a separate product liability agreement. 1. We cannot accept responsibility for any defect, which may arise from additional manufacturing of the product (including disassembly and reassembly), after product delivery. 2. We cannot accept responsibility for any defect, which may arise after the application of strong external force to the product. 3. We cannot accept responsibility for any defect, which may arise due to the application of static electricity after the product has passed your companys acceptance inspection procedures. 4. When the product is in CFL models, CFL service life and brightness will vary according to the performance of the inverter used, leaks, etc. We cannot accept responsibility for product performance, reliability, or defect, which may arise. 5. We cannot accept responsibility for intellectual property of a third party, which may arise through the application of our product to your assembly with exception to those issues relating directly to the structure or method of manufacturing of our product. 6. We will not be held responsible for any quality issue(s) after two years and beyond from its production date indicated on the lot number (please refer to Code System of Production Lot indicated earlier in this specification). T-51750GDO065J-FW-AFN Rev.2 KYOCERA Display Corporation Page 26/26