TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function TO-220 TO-263 2 (D PAK) Pin Definition: TS39150 1. Input 2. Ground (tab) 3. Output TO-220-5L TO-263-5L 2 (D PAK) Pin Definition: TS39151xx TS39152 1. Enable 1. Enable 2. Input 2. Input 3. Ground 3. Ground 4. Output 4. Output 5. Flag 5. Adjust TS39153 1. Enable 2. Input 3. Ground 4. Output 5. Sense General Description TS39150/1/2/3 are 1.5A ultra low dropout linear voltage regulators that provide low voltage, high current output from an extremely small package. These regulator offers extremely low dropout (typically 400mV at 1.5A) and very low ground current (typically 12mA at 1.5A). TS39150/1/2/3 are fully protected against over current faults, reversed input polarity, reversed lead insertion, over temperature operation, positive and negative transient voltage spikes, logic level enable control and error flag which signals whenever the output falls out of regulation. On the TS39150/1/2/3, the enable pin may be tied to VIN if it is not required for enable control. Features Ordering Information Dropout voltage typically 0.4V @ Io=1.5A Output Current up to 1.5A Low Ground Current Extremely Fast Transient Response Reversed Leakage & Reverse Battery Protection Error Flag Signals Output (TS39151 only) Internal Current Limit Thermal Shutdown Protection Application TM PowerPC Power Supplies Battery Powered Equipment Consumer and Personal Electronics High Efficiency Linear Power Supplies SMPS Post Regulator and DC to DC Modules High-efficiency Post Regulator for Switching Supply Low-Voltage microcontrollers and Digital Logic Part No. Package Packing TS39150CZxx C0 TO-220 50pcs / Tube TS39150CMxx RN TO-263 800pcs / 13" Reel TS39151CZ5xx C0 TO-220-5L 50pcs / Tube TS39151CM5xx RN TO-263-5L 800pcs / 13" Reel TS39152CZ5 C0 TO-220-5L 50pcs / Tube TS39152CM5 RN TO-263-5L 800pcs / 13" Reel TS39153CZ5xx C0 TO-220-5L 50pcs / Tube TS39153CM5xx RN TO-263-5L 800pcs / 13" Reel Note: Where xx denotes voltage option, available are 18=1.8V 25=2.5V 33=3.3V 50=5.0V Contact to factory for addition output voltage option. Pin Description Pin Configuration Pin Description Enable TTL/COMS compatible input. Logic high is enable; logic low or open is shutdown Input Ground Unregulated input: +16V maximum supply Ground: Ground pin and TAB / heat sink are internally connected. Output Regulator output Error Flag (output): Open-collector output. Active low indicates an output fault condition, if no used, leave open. Flag (fixed voltage) Feed Back (adjustable) Adjustment input: Feedback input. Connect to resistive voltage-divider network. 1/12 Version: D07 TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function Absolute Maximum Rating (Note 1) Supply Voltage Enable Voltage Storage Temperature Range VIN -20V ~ +20 VEN TSTG +20 -65 ~ +150 o Lead Soldering Temperature (260 C) ESD V V C o 5 (Note 3) S Operating Rating (Note 2) Operation Input Voltage VIN (operate) +2.25 ~ +16 V Operation Enable Voltage Power Dissipation (Note 4) VEN (operate) PD +2.25 ~ +16 Internally Limited V W TJ -40 ~ +125 Operating Junction Temperature Range o C Electrical Characteristics o VIN = VOUT + 1V, VIN =2.5V for fixed reference output voltage, Venable= 2.25V, Ta = 25 C, unless otherwise specified. Parameter Fixed Output Voltage Fixed Reference Output Voltage Fixed Reference Output Voltage Conditions 10mA IL 1.5A, Vo+1V VIN 8V IL=10mA 10mA IL 1.5A, 2.5V VIN 8V Min Typ Max Unit 0.980|Vo| VOUT 1.020|Vo| V 0.980|Vo| 0.970|Vo| 1.24 (VREF) 1.020|Vo| 1.030|Vo| V Line Regulation IL=10mA, Vo+1V VIN 16V -- 0.05 0.5 % Load Regulation VIN =Vout+1V, 10mAIL1.5A -- 0.2 1.0 % VOUT = -1% 40 100 275 400 100 250 350 630 ppm/ C IL=100mA IL=750mA IL=1.5A ----- Quiescent Current (Note 6) VIN= VOUT +1V IL=100mA IL=750mA IL=1.5A ---- 5 7 25 18 20 -- mA Current Limited VOUT=0, VIN =VOUT+1V -- 2.0 2.5 A (Note 7) 0.980|Vo| 0.970|Vo| 1.24 1.020|Vo| 1.030|Vo| V (Note 8) --- 40 20 120 -- nA o ppm/ C -- 0.1 -- nA/ C Output Voltage Temp. Coefficient Dropout Voltage (Note 5) o mV Reference (TS39152) Reference Voltage Reference Voltage Adjust Pin Bias Current Reference Voltage Temp. Coefficient Adjust Pin Bias Current Temp. Coefficient o Enable Input (TS39151/2/3) Input Logic Voltage Low (OFF) High (ON) -2.25 --- 0.8 -- V Enable Pin Input Current VEN =2.25V VEN =0.8V --- --- 75 4 uA 2/12 Version: D07 TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function Electrical Characteristics (Continue) Flag Output (TS39151/3) Output Leakage Current VOH=16V -- -- 2 uA Output Low Voltage (Note 9) Upper Threshold Voltage VIN=0.9 * VOUT, IOL=250uA % of VOUT --- --- 400 99 mV % Lower Threshold Voltage Hysteresis % of VOUT 93 -- -1 --- % % Thermal Performance Condition Thermal Resistance Junction to Case Package type TO-220 / TO-220-5L TO-263 / TO-263-5L Typ 80 80 Unit o C/W Note 1: Absolute Maximum Rating is limits beyond which damage to the device may occur. For guaranteed specifications and test conditions see the Electrical Characteristics. Note 2: The device is not guaranteed to operate outside its operating rating. Note 3: Devices are ESD sensitive. Handling precautions recommended. Note 4: The maximum allowable power dissipation is a function of the maximum junction temperature, TJ, the junction to ambient thermal resistance, JA, and the ambient temperature, Ta. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. The effective value of JA can be reduced by using a heat sink, Pd(max) = (TJ(max) - Ta) / JA. Note 5: Dropout voltage is defined as the input to output differential at which the output voltage drops -1% below its nominal value measured at 1V differential. Note 6: Ground pin current is the regulator quiescent current. The total current drawn from the source is the sum of the ground pin current and output load current, IGND = IIN - IOUT for fix output voltage, , IGND = IIN - IOUT +10mA for fix reference output voltage in full load regulation. Note 7: VREF VOUT (VIN - 1V), 2.25V VIN 16V, 10mA IL 1.0A. o Note 8: Output voltage temperature coefficient is VOUT (worse cast) / (TJ(max) - TJ(MIN)) where is TJ(max) +125 C and o TJ(MIN) is 0 C. Note 9: For adjustable device and fixed device with VOUT > 2.25V. 3/12 Version: D07 TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function Functional Diagram TS39150 Fixed Regulator Block Diagram TS39151/3 Fixed Regulator with Flag, Sense and Enable Block Diagram TS39152 Adjustable Regulator Block Diagram 4/12 Version: D07 TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function Application Information The TS3915x series are high performance with low dropout voltage regulator suitable for moderate to high current and voltage regulator application. Its 630mV dropout voltage at full load and over temperature makes it especially valuable in battery power systems and as high efficiency noise filters in post regulator applications. Unlike normal NPN transistor design, where the base to emitter voltage drop and collector to emitter saturation voltage limit the minimum dropout voltage, dropout performance of the PNP output of these devices is limited only by low VCE saturation voltage. The TS3915x series is fully protected from damage due to fault conditions. Linear current limiting is provided. Output current during overload conditions is constant. Thermal shutdown the device when the die temperature exceeds the maximum safe operating temperature. Transient protection allows device survival even when the input voltage spikes above and below nominal. The output structure of these regulators allows voltages in excess of the desired output voltage to be applied without reverse current flow. Output Capacitor Requirement The TS3915x series requires an output capacitor to maintain stability and improve transient response is necessary. The value of this capacitor is dependent upon the output current, lower currents allow smaller capacitors. TS3915x series output capacitor selection is dependent upon the ESR of the output capacitor to maintain stability. When the output capacitor is 10uF or greater, the output capacitor should have an ESR less than 2. This will improve transient response as well as promote stability. Ultra low ESR capacitors (<100m), such as ceramic chip capacitors, may promote instability. These very low ESR levels may cause an oscillation and/or under damped transient response. A low ESR solid tantalum capacitor works extremely well and provides good transient response and stability over temperature aluminum electrolytes can also be used, as long as the ESR of the capacitor is <2. The value of the output capacitor can be increased without limit. Higher capacitance values help to improve transient response and ripple rejection and reduce output noise. Input Capacitor Requirement An input capacitor of 1uF or greater is recommended when the device is more than 4" away from the bulk AC supply capacitance or when the supply is a battery. Small, surface mount, ceramic chip capacitors can be used for bypassing. Larger values will help to improve ripple rejection by bypassing the input to the regulator, further improving the integrity of the output voltage. Minimum Load Current The TS3915x series is specified between finite loads. If the output current is too small leakage currents dominate and the output voltage rises. A 10mA minimum load current is necessary for proper regulation. Adjustable Regulator Design The adjustable regulator versions (TS39152) is allow to programming the output voltage anywhere between 1.25 and the 16V maximum operating rating of the family. Two resistors are used. Resistors can be quite large up to 1M, because of the very high input impedance and low bias current of the sense comparator, the resistor values are calculated by: Where VOUT is the desired output voltage. Above application circuit shows component definition. Applications with widely varying load currents may scale the resistors to draw the minimum load current required for proper operation. 5/12 Version: D07 TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function Application Information (Continue) Enable Input TS39151/2/3 versions feature an active-high enable (EN) input that allows ON/OFF control of the regulator. Current drain reduces to "zero" when the device is shutdown, with only micro-amperes of leakage current. The EN input has TTL/CMOS compatible thresholds for simple interfacing with logic interfacing. EN may be directly tied to VIN and pulled up to the maximum supply voltage. Error Flag TS39151 versions feature an Error Flag, which looks at the output voltage and signals an error condition when this voltage drops 5% below its expected value. The error flag is an open-collector output that pulls low under fault conditions. It may sink 10mA. Low output voltage signifies a number of possible problems, including an over-current fault (the device is in current limit) or low input voltage. The flag output is inoperative during over temperature shutdown conditions. A pull-up resistor from error flag to either VIN or VOUT is required for proper operation. For information regarding the minimum and maximum values of pull-up resistance, refer the graph as follow: Transient Response and 3.3V to 2.5V or 2.5V to 1.8V Conversion TS3915x has excellent transient response to variations in input voltage and load current. The device have been designed to respond quickly to load current variations and input voltage variations. Large output capacitors are not required to obtain this performance. A standard 10uF output capacitor, preferably tantalum, is all that is required. Larger values help to improve performance even further. By virtue of its low dropout voltage, this device does not saturate into dropout as readily as similar NPN base designs. When converting from 3.3V to 2.5V or 2.5V to 1.8V, the NPN based regulators are already operating in dropout, with typical dropout requirements of 1.2V or greater,. To convert down to 2.5V or 1.8V without operating in dropout, NPN based regulators require an input voltage of 3.7V at the very least. The TS3915x regulator will provide excellent performance with an input as low as 3.0V or 2.5V respectively. This gives the PNP based regulators a distinct advantage over older, NPN based linear regulators. Output Sense The fixed voltage regulator versions (TS39153) is connected to the output pin of the regulator. In critical applications, small voltage drops are caused by the resistance (Rp) of PC traces between the regulator and the load. These may be eliminated by connecting the sense pin to the output at the load as follow: (Kelvin Sense Connection). Typical Application Circuit 2.5V/1.5A Regulator with Error Flag 2.5V/1.5A Regulator 6/12 Version: D07 TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function Application Information (Continue) Thermal Characteristics TS3915x series linear regulators are simple to use, the most complicated design parameters to consider are thermal characteristics, thermal design requires the following application specification parameters: Maximum ambient temperature, TA Output current, IOUT Output voltage, VOUT Input voltage, VIN Calculate the power dissipation of the regulator from these numbers and the device parameters from this datasheet, where the ground current is taken from data sheet. PD = (VIN - VOUT) x IOUT + VIN x IGND The heat sink thermal resistance is determined by: SA = (TJ(MAX) - TA) / PD - (JC + CS) Where TJ(MAX) 125oC and CS is between 0oC and 2oC/W. The heat sink may by significantly reduced in applications where the minimum input voltage is know and is large compared with the dropout voltage and distribute the heat between this resistor and the regulator. The low dropout properties of vertical PNP regulators allow significant reductions in regulator power dissipation and the associated heat sink without compromising performance. When this technique is employed, a capacitor of at least 1uF is needed directly between the input and regulator ground. 7/12 Version: D07 TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function TO-220 Mechanical Drawing DIM A B C D E F G H I J K L M N O P TO-220 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 10.000 10.500 0.394 0.413 3.740 3.910 0.147 0.154 2.440 2.940 0.096 0.116 6.350 0.250 0.381 1.106 0.015 0.044 2.345 2.715 0.092 0.107 4.690 5.430 0.185 0.214 12.700 14.732 0.500 0.580 8.382 9.017 0.330 0.355 14.224 16.510 0.560 0.650 3.556 4.826 0.140 0.190 0.508 1.397 0.020 0.055 27.700 29.620 1.091 1.166 2.032 2.921 0.080 0.115 0.255 0.610 0.010 0.024 5.842 6.858 0.230 0.270 Marking Diagram XX Y M L = Output Voltage (18=1.8V, 25=2.5V, 33=3.3V, 50=5V) = Year Code = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) = Lot Code 8/12 Version: D07 TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function TO-263 Mechanical Drawing DIM A B C D E F G H I J TO-263 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 10.000 10.500 0.394 0.413 14.605 15.875 0.575 0.625 0.508 0.991 0.020 0.039 2.420 2.660 0.095 0.105 4.064 4.830 0.160 0.190 1.118 1.400 0.045 0.055 0.450 0.730 0.018 0.029 8.280 8.800 0.325 0.346 1.140 1.400 0.044 0.055 1.480 1.520 0.058 0.060 Marking Diagram XX Y M L = Output Voltage (18=1.8V, 25=2.5V, 33=3.3V, 50=5V) = Year Code = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) = Lot Code 9/12 Version: D07 TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function TO-220-5L Mechanical Drawing DIM A B C D E F G H I J K L M N TO-220-5L DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 10.00 10.50 0.394 0.413 3.240 4.440 0.128 0.175 2.440 2.940 0.096 0.116 0.260 1.020 0.010 0.040 1.570 1.830 0.062 0.072 13.31 14.13 0.524 0.556 4.475 5.225 0.176 0.206 1.170 1.370 0.046 0.054 27.60 29.44 1.087 1.159 2.175 2.925 0.086 0.115 0.297 0.477 0.012 0.019 8.280 8.800 0.326 0.346 6.010 6.510 0.237 0.256 14.29 15.31 0.563 0.603 Marking Diagram TS39151 / TS39152 / TS39153 Y = Year Code M = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) L = Lot Code XX = Output Voltage - TS39151 & TS39153 only (18=1.8V, 25=2.5V, 33=3.3V, 50=5V) XXX = CZ5 - TS39152 only 10/12 Version: D07 TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function TO-263-5L Mechanical Drawing DIM A B C D E F G H I J TO-263-5L DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 10.220 10.260 0.402 0.404 14.600 15.870 0.575 0.625 0.750 0.770 0.030 0.030 1.573 1.827 0.062 0.072 4.560 4.570 0.179 0.180 1.240 1.270 0.049 0.050 2.280 2.790 0.090 0.110 0.280 0.320 0.011 0.013 8.240 8.280 0.324 0.326 1.540 1.800 0.060 0.071 Marking Diagram TS39151 / TS39152 / TS39153 Y = Year Code M = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) L = Lot Code XX = Output Voltage - TS39151 & TS39153 only (18=1.8V, 25=2.5V, 33=3.3V, 50=5V) XXX = CM5 - TS39152 only 11/12 Version: D07 TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function Notice Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, to any intellectual property rights is granted by this document. Except as provided in TSC's terms and conditions of sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale. 12/12 Version: D07