REVISIONS
LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
G
Add two pa ckages, F-5 and C-2. Change to military dra wing format. Ma de
change s to 1.3, table I, 6.4, figure 1, and editorial cha nges throughout. Add one
v endor CAGE 34371.
89-09-13
M. Frye
H
Add new device type 02. Editorial changes thro ughout. Add v endor CAGE
1ES66. Change PDA from 10 percent to 5 percent. Ma ke changes to 1.3 and
table I. Remove ve ndor CAGE 32293.
92-11-13
M. Frye
J
Changes in accordance with NOR 5962-R134-95.
95-05-09
M. Frye
K
Drawing update d to re flect current requireme nts. Incorporate NOR revision J.
Editoria l cha nges throughout. - drw
00-09-15
Raymond Mo nnin
L
Drawing update d to current require ments. Editorial changes throughout. - drw
03-02-12
Raymond Mo nnin
THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED.
CURRENT CAGE CODE 67268
REV
SHEET
REV
SHEET
REV STATUS REV L L L L L L L L L
OF SHEETS SHEET 1 2 3 4 5 6 7 8 9
PMIC N/A PREPARED BY
Ri ck Officer
DEF ENSE S UPPLY CENTER CO L UMBUS
STANDARD
MICROCIRCUIT
DRAWING
CHECKED BY
Charles E. Besore
COLUMBUS, OHIO 43216
http://www.dscc.dla.mil
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
APPROVED BY
M. Frye
MICROCIRCUIT , CMO S , Q UA D A NA L O G S WIT CH,
MONOLITHIC SILICON
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
DRAWING APPROVAL DATE
77-11-04
AMSC N/A
REVISION LEVEL
L SIZE
A CAGE CODE
14933
77053
SHEET
1 OF
9
DSCC FORM 2233
APR 97 5962-E192-03
DISTRIBUTION STATEMENT A. Approve d for public relea se; distribution is unlimited.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
77053
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OH IO 43216-5000 REVISION LEVEL
L SHEET 2
DSCC FORM 2234
APR 97
1. SCOPE
1.1 Scope. This drawing des cribes de vice requirements for MIL-STD-883 compliant, non-JAN class level B mi crocircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifyi ng Num ber (PIN). The complete PI N i s a s s hown in the following ex a mple:
77053 01 E A
Drawing num ber
Device type
(see 1.2.1) Case outline
(see 1.2.2) Lead finish
(see 1.2.3)
1.2.1 De vice types . The device types identify the circuit function as foll ows:
Device ty pe Generic number Circuit function
01 DG201A Quad SPST analog switch
02 HI-201 Quad SPST analog switch, with dielectric isolat ion
1.2.2 Ca se outline s. The case outlines a re a s des ignate d in MIL-STD-1835 and as follows:
Outline letter Descriptive desi gnator Terminals Package styl e
2 CQCC1-N 20 20 Square l eadles s chip carrier package
E GDIP1-T16 or CDIP2-T16 16 Dual-in-line pa ckage
F GDFP2- F16 or CDFP3-F 16 16 Flat pack
X CDFP4-F16 16 Flat pack
1.2.3 Le ad finish. The lead finish is a s spe cified in MIL-PRF-38535, appendix A.
1.3 Absolute m ax imum r atings.
Supply v oltage (between V+ and V-):
Device type 01......................................................................... 44 V dc
Device type 02......................................................................... 40 V dc
Digital input voltage (VIN):
Device type 01......................................................................... V- -0.3 V dc to V+
Device type 02......................................................................... V- -4 V dc to V+ +4 V dc
Anal og input voltage ( VS)............................................................ V- -2 V dc to V+ +2 V dc
Current (any te rmi nal except S or D):
Device type 01......................................................................... 30 mA
Device type 02......................................................................... 25 mA
Continuous current, S or D:
Device type 01......................................................................... 20 mA
Device type 02......................................................................... 25 mA
Peak current, S or D
(pulsed a t 1 ms, 10 percent duty cy cle m aximum):
Device type 01......................................................................... 70 mA
Device type 02......................................................................... 40 mA
Storage temperature range......................................................... -65°C to +150°C
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
77053
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OH IO 43216-5000 REVISION LEVEL
L SHEET 3
DSCC FORM 2234
APR 97
Power dissipation (PD)................................................................ 750 mW 1/
Lead t empera ture (soldering, 10 se conds)................................. +275°C
Thermal resistance, junction-to-case (θJC)................................. See MIL-STD-1835
Junction tempe rature (TJ):
Device type 01......................................................................... +150°C
Device type 02......................................................................... +175°C
V+ to ground:
Device type 01......................................................................... +25 V
Device type 02......................................................................... +20 V
V- to ground:
Device type 01......................................................................... -25 V
Device type 02......................................................................... -20 V
1.4 Recommended operating conditions.
Positive supply vol tage (V+)........................................................ +15 V dc
Negat ive supply v oltage (V-)....................................................... -15 V dc
M inimum di gital high level i nput voltage (VIH) ............................. +2.4 V dc
M ax imum digi ta l low level input voltage (VIL) .............................. +0.8 V dc
Am bient operating tempera tur e range (TA) ................................ -55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Gove rnment specification, standar ds, and handbooks. The following specif ication, s tandards, and handbooks form a part
of this drawi ng to the ex tent specifie d here in. Unless otherwise specified, the issues of these documents ar e those listed in the
issue of the Department of Defe nse Index of Specifica tions a nd Standa rds (DoDISS) and supplem ent thereto, cited in the
solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 - Inte grated Circuits, Manufacturing, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Ele ctroni c Com ponent Case Out line s.
HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Unless otherwise indicated, copies of the specifica tion, s ta ndards , and handbooks ar e availa ble from the Standardiza tion
Docume nt Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence . In the eve nt of a conflict between the text of this drawing and the references cited herein, the tex t of
this dra w ing takes prece dence. Nothing in this document, however, supersede s appli cable laws a nd regulations unless a specific
exempt ion has bee n obtained.
1/ For case E, derate at 12 mW/°C above TA = +75°C. For case 2, F and X, derate at 10 mW/°C above TA = +75°C.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
77053
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OH IO 43216-5000 REVISION LEVEL
L SHEET 4
DSCC FORM 2234
APR 97
3. REQUIREMENTS
3.1 Item requirement s. The indiv idual item requirem ents shall be in accorda nce with MIL-PRF- 38535, a ppendi x A for non-JAN
class leve l B devices a nd as s pecified herein. Product buil t to this dra wing that is produced by a Quali fied Manuf acturer Lis ting
(QM L) certified a nd qualified m anufacturer or a manufa cturer who ha s bee n granted transitional certification to MIL-PRF-38535
ma y be process ed as Q M L product in a ccordance with the m anufa cturers approved pr ogram plan and qua lifying activity a pproval
in accordance with MIL-PRF-38535. This QML flow as docum ented in the Quality M anage m ent (QM ) plan may make
modifi cati ons to the requirements herein. These modifications shall not affect form, fit, or function of the device. These
modifications shall not a ffect the PIN as des cribed he rein. A "Q" or "QML" certification ma rk in accordance with MIL-PRF-38535 is
require d to identify when the QML flow option is use d.
3.2 Design, constr uction, a nd phys ical dimens ions. The de sign, construction, and phy sical dime nsi ons sha ll be as spe cified in
MIL-PRF-38535, a ppendi x A a nd herein.
3.2.1 Ca se outline s. The case outlines sha ll be in accordance with 1.2.2 herein.
3.2.2 Te rmi nal connections. The termi nal connections shal l be as s pecified on figure 1.
3.3 Electrical pe rformance cha racteristics. Unless otherwise specified herein, the electrical performance characteristics are as
specified in table I and s hall apply ove r the full ambie nt operating tempera ture range.
3.4 Electrical test re quirements. The el ectrical tes t requirements sha ll be the subgroups spe cified in table II . The e lectr ical tests
for e ach subgroup are describe d in table I.
3.5 Marking. Ma rking sha ll be in accordance with MIL-PRF-38535, appendix A. The pa rt shall be mar ked with the PIN l isted in
1.2 herein. In addition, the manuf acturer's PIN ma y a lso be mar ked as listed in MIL-HDBK-103 (see 6.6 herein). For packa ges
where ma rking of the entire SMD PIN num ber is not fe asible due to space limita tions, the manufacturer has the option of not
ma rking the "5962-" on the de vice.
3.6 Certificate of compli ance. A certificat e of compli ance s hal l be required from a m anufacturer in orde r to be listed as an
approv ed source of supply in MIL-HDBK-103 (see 6.6 herein). The certificat e of compliance s ubmitte d to DSCC-VA prior to listing
as an approve d source of s upply sha ll affirm t hat the manuf acturer's product me ets the requireme nts of M IL-PRF-38535, appendix
A and the requireme nts herein.
3.7 Certificat e of conformance . A certificate of confor m ance a s re quired in MIL-PRF-38535, appendix A s hall be provided with
each l ot of microcir cuits delive red to this drawing.
3.8 Notification of change. Notif ication of cha nge to DSCC-VA shall be required in accordance with MIL-PRF- 38535, a ppendi x
A.
3.9 Verifi cation and review. DSCC, DSCC's agent, and the acquiri ng activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
revi ewer.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
77053
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OH IO 43216-5000 REVISION LEVEL
L SHEET 5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristi cs.
Test
Symbol
Conditions 1/
-55°C ≤ TA ≤+125°C
unless othe rwise s pecified
Group A
subgroups
Devic e
ty pe
2/
Limits
Unit
Min Max
Analog signal range VS 3/ 1, 2, 3 All ±15 V
Drain-source ON re sista nce RDS(ON) VD = ±10 V, VIN = 0.8 V, 1, 3 01 175 Ω
ID = ±1 mA 2 250
VS = ±10 V, VIN = 0.8 V, ID =
m
1 mA, All unus ed channels 1 02 70
V
A = 2.4 V 2, 3 100
Off input leaka ge current IS(OFF) VIN = 2.4 V, VS = ±14 V, 1 All
±2 nA
VD =
m
14 V 2, 3 ±100
Off output leakage curr ent ID(OFF) VIN = 2.4 V, V S = ±14 V, 1 01
±1 nA
02 ±2
2, 3 All ±100
On leakage current ID(ON) V
IN = 0.8 V, 1 01 ±1 nA
VD = VS = ±14 V 02
±2
2, 3 All ±200
Low level input v oltage VIL 1, 2, 3 All 0.8 V
High level input voltage VIH 1, 2, 3 All 2.4 V
Low level input leaka ge IIL V
IN = 0 V 1 01 ±1 µA
current 2 ±10
V
IN = 0.8 V 1 02 ±0.5
2, 3 ±1
High level input leakage IIH V
IN = 2.4 V, 15 V 1 01 ±1 µA
current 2 ±10
1 02 ±0.5
2, 3 ±1
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
77053
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OH IO 43216-5000 REVISION LEVEL
L SHEET 6
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristi cs - Cont inued.
Test
Symbol
Conditions 1/
-55°C ≤ TA ≤+125°C
unless othe rwise s pecified
Group A
subgroups
Devic e
ty pe
2/
Limits
Unit
Min Max
Switch ON time tON RL = 1kΩ, CL = 35 pF,
VIH = +3 V, VIL = 0 V 9, 10, 11 01 1000 ns
RL = 1kΩ, CL = 100 pF, 9 02 600
VIH = +4 V, VIL = 0 V 10, 11 800
Switch OFF time tOFF RL = 1kΩ, CL = 35 pF, 9 01 500 ns
VIH = +3 V, VIL = 0 V 10, 11 650
RL = 1kΩ, CL = 100 pF, 9 02 500
VIH = +4 V, VIL = 0 V 10, 11 650
Positive s upply current I+ VIN = 0 V 1, 2 01 4 mA
3 6.5
V
IN = 5 V 1, 2 3
3 4.5
V
IN = 0.8 V 1, 2 02 1.5
3 2
V
IN = 2.4 V 1, 2 1.5
3 2
Negativ e supply current I- VIN = 0 V 1, 2 01 -4 mA
3 -6.5
V
IN = 5 V 1, 2 -3
3 -4.5
V
IN = 0.8 V 1, 2 02 -1. 5
3 -2
V
IN = 2.4 V 1, 2 -1. 5
3 -2
1/ Unless otherwise specified, V+ = +15 V dc and V- = -15 V dc.
2/ The limi ting te rms “m in” (mini m um ) and “m ax ” (ma ximum) sha ll be cons idered to apply to m agnitudes only.
Negativ e current shall be defined a s conv entional current flow out of a devi ce te rminal.
3/ Guaranteed, if not tested, to the limits s pecified.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
77053
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OH IO 43216-5000 REVISION LEVEL
L SHEET 7
DSCC FORM 2234
APR 97
Device t ype 01 02
Case outline s E, F and X 2 E 2
Terminal number Terminal sy mbols
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
IN1
D1
S1
V-
GND
S4
D4
IN4
IN3
D3
S3
NC
V+
S2
D2
IN2
- - -
- - -
- - -
- - -
NC
IN1
D1
S1
V-
NC
GND
S4
D4
IN4
NC
IN3
D3
S3
NC
NC
V+
S2
D2
IN2
IN1
D1
S1
V-
GND
S4
D4
IN4
IN3
D3
S3
VREF 1/
V+
S2
D2
IN2
- - -
- - -
- - -
- - -
NC
IN1
D1
S1
V-
NC
GND
S4
D4
IN4
NC
IN3
D3
S3
VREF 1/
NC
V+
S2
D2
IN2
1
/ VREF is norma lly floating, but voltage up t o 10 V can be a pplied to raise the threshold voltage .
FIGURE 1. Terminal connections .
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
77053
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OH IO 43216-5000 REVISION LEVEL
L SHEET 8
DSCC FORM 2234
APR 97
4. QUALITY ASSURANCE PROVISIONS
4.1 Sampling and inspection. Sampling and inspe ction procedures shall be in accordance wi th MIL-PRF- 38535,
appendix A.
4.2 Scre ening. Screening shall be in accordance wi th method 5004 of MIL-STD- 883, and s hall be conducted on a ll de vices
prior t o qual ity conformance inspection. The following a dditional criteria shall apply:
a. Burn- in test, m ethod 1015 of MIL-STD-883.
(1) Tes t condit ion A, B, C, D, or E. The test circuit s hal l be mai nta ined by the manuf acturer under document revision leve l
control and s hal l be m ade avail abl e to the preparing or acquiring activ ity upon reques t. The test circuit shall s pecify the
inputs, outputs, biases , a nd power diss ipation, a s applicable, in accordance with the intent specifie d in test m ethod
1015 of MIL-STD-883.
(2) TA = +125°C, minimum.
b. Interim and final electrical te s t parameters shall be as s pecified in table II herein, except interim ele ctri cal parameter tests
prior t o burn-in are optional at the dis cre tion of the manufa cturer.
TABLE II. El e ctri cal te s t re quirements.
MIL-STD-883 te st require m ents
Subgroups
(in accordance with
MIL-STD-883, method 5005,
table I)
Interim ele ctrical parameters
(method 5004) - - -
Final electrical te s t parameters
(method 5004) 1*, 2, 3, 9
Group A test requirements
(method 5005) 1, 2, 3, 9, 10, 11
Groups C and D e nd-point
el e ctrical parameters
(method 5005) 1
* PDA applies to subgroup 1.
4.3 Q uality conformance inspe ction. Quality conforma nce inspection s hall be in accordance with method 5005 of
MIL-STD-883 including groups A, B, C, and D inspe ctions. The following additional criteria shall apply.
4.3.1 Gr oup A inspection.
a. Tests shall be as specified in table II herein.
b. Subgr oups 4, 5, 6, 7, and 8 in table I, me thod 5005 of MIL-STD-883 sha ll be omitted.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
77053
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OH IO 43216-5000 REVISION LEVEL
L SHEET 9
DSCC FORM 2234
APR 97
4.3.2 Gr oups C and D inspections.
a. End-point e lectrica l parame ters sha ll be as spe cified in table II herein.
b. Steady-state life te st conditions , method 1005 of MI L-STD- 883.
(1) Test condition A, B, C, D, or E. The test circuit shall be maintained by the manufa cturer unde r document revision
level control a nd shall be made avail able to the pre paring or acquiring activ ity upon reques t. The te st circuit shall
specify the inputs, outputs, biases , and powe r diss ipa tion, a s applicable, in accordance with the inte nt spe cified in
test method 1005 of MIL-STD-883.
(2) TA = +125°C, minimum.
(3) Test duration: 1,000 hour s, except as pe rmitted by method 1005 of MIL-STD-883.
5. PACKAGING
5.1 Packaging requirement s. The requirem ents for packaging shall be in accorda nce with MI L-PRF- 38535, a ppendi x A.
6. NOTES
6.1 Intended use. Microcircuits conforming to this dra w ing are inte nded for use for Gov ernment m icrocircuit applications
(original equipm ent), de sign appl ications, and logis tics pur poses .
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared
specification or drawing.
6.3 Configuration control of SMD's . All proposed changes to existing SMD's will be coordinated with the users of record for the
individual documents. This coordination will be accomplished using DD Form 1692, Engine ering Change Proposal.
6.4 Record of use rs. Military and industria l users shall infor m Defense Supply Center Columbus when a sy stem application
requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for
coordination and distribution of cha nges to the drawi ngs. Users of draw ings cove ring microelectronics dev ices (FSC 5962) shoul d
contact DSCC-VA, te lephone (614) 692-0544.
6.5 Comm ents. Comment s on this drawing should be directed to DSCC-VA, Columbus , Ohio 43216-5000, or telephone (614)
692-0547.
6.6 Approved sources of supply. Approved sources of supply are l iste d in MIL-HDBK-103. The ve ndors listed in MIL-HDBK-
103 have a gree d to this drawing and a ce rtificate of com plia nce (s ee 3.6 here in) has been submitt ed to and accept ed by DSCC-
VA.
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 03-02-12
Approve d sources of supply for SMD 77053 are listed below for imme diate acquisition information only and sha ll be
added to MIL-HDBK-103 and QML-38535 dur ing the next rev ision. MIL-HDBK-103 a nd QM L-38535 will be revised to
include the addition or deletion of sour ces. The v endors listed below have agreed to this dra w ing and a cer tificate of
compliance ha s been s ubmitte d to and a ccepted by DSCC-VA. This bulletin is supe rseded by the ne xt dated revi sion of
MIL-HDBK-103 and QML-38535.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
Similar military
specification PIN
77053012A
77053012C 17856
1ES66 DG201AAZ/883
DG201AAZ/883B
7705301EA 17856
1ES66 DG201AAK/883
DG201AAK/883B M38510/12302BEA
7705301FA 3/
7705301XA
7705301XC 17856
1ES66 DG201AAL/883
DG201AAL/883B
77053022A
77053022C 34371
1ES66 HI4-201/883
HI4-201/883B
7705302EA 1ES66
3/ HI1-201/883B
HI1-201/883
1/ The lead finis h shown for ea ch PIN representing
a hermetic package is the most readil y available
from the manufacturer l isted for that part. If the
desired lea d finish is not liste d contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items a cquired to this number ma y not
satisfy the per formance re quirement s of this dra w ing.
3/ Not a va ilable from an approved s ource.
Vendor CAGE Vendor nam e
numbe r and addre ss
1ES66 Ma xim I ntegrated Products
120 San G abriel Dri ve
Sunnyv ale, CA 94086-5125
17856 Siliconix Incorporated
2201 Laurelwood Road
Santa Clara, CA 95054-1516
34371 Intersil Corporation
2401 Palm Ba y Blvd.
P.O. Box 883
Me lbourne, FL 32901-0883
The information contained her ein is disseminate d for convenience only and t he
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
