Series AMEOR30-AZ
up to 2.5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 052.1e R3.L 1 of 14 North America only
FEATURES:
Models
Single output
Model
Max
Output
Power
(W) *
Output
Voltage
Range (V)
Output
Current
(A)
Input Voltage
(VAC/Hz)
Input Voltage
(VDC)
Efficiency
(%)
AMEOR30-5070AZ
35
36-50
0.7
90-277/47-440
130-390
86
AMEOR30-4864AZ
30.72
36-48
0.64
90-277/47-440
130-390
86
AMEOR30-36100AZ
36
24-36
1
90-277/47-440
130-390
85
AMEOR30-24140AZ
33.6
12-24
1.4
90-277/47-440
130-390
84
AMEOR30-12250AZ
30
5-12
2.5
90-277/47-440
130-390
83
*Exceeding the maximum output power will permanently damage the converter
All models can be ordered with optional North American colour input wires (black (L), white (N), green (GND)). Add “–NA” to
part number when ordering.
NOTE: Aimtec limited warranty of 5 years is valid based on product operation at datasheet specifications at ambient temperature of 25°C,
humidity<75%, nominal input voltage (115/230/277VAC) and at rated output load unless otherwise specified. See
http://www.aimtec.com/terms-sale
AMEOR30-AZ’s AC/DC LED drivers have electrical safeguards designed within to protect it from conventional electrical abnormalities with
the levels listed in the safety table. Applications for use within rural agricultural, heavy industrial, and other areas or regions which are
prone to ‘dirty’ electrical conditions which would subject any of the above models to excessive voltages surges or spikes, may damage or
cause early life failure of product. In this case consideration should be made by the end user to ensure that adequate line or mains surge
suppression is installed in front of Aimtec device to ensure the longevity of the products. Failure to identify excessive line surges violations
prior to installation may damage sensitive equipment permanently.
Input Specifications
Parameters
Conditions
Typical
Maximum
Units
Inrush current <2ms
115VAC
25
A
230VAC
40
Leakage current
115VAC
0.3
mA
230VAC
0.5
AC current
115VAC
0.33
A
230VAC
0.16
Power Factor
115VAC
0.99
230VAC
0.97
External fuse
250V/1A
Start up time
450
ms
Surge voltage
2sec
440
V
Output Specifications
Parameters
Conditions
Typical
Maximum
Units
Current accuracy
±3
%
Line regulation
LL-HL
±1
%
Load regulation
0-100% load
±3
%
Ripple & Noise *
20MHz Bandwidth
75
mV p-p
Hold-up time
50
ms
Current adjustment range
100-0
%
Minimum Load Voltage
See the models table
* Tested with 0.1µF (M/C) or (C/C) and 47µF (E/C) parallel capacitors at the end.
• AC-DC Constant current LED Driver
• Over Temperature Protection
• Input range 90-277VAC/47-440Hz
• Open frame
• High Efficiency up to 86%
• Power Factor Correction
• Operating temperature -40 to 80°C
• Dimmable via analog / 0-10Vdc / PWM
(C version see table)
• SCP, Over Current Protection
• 5 Years Limited Warranty
Click on Series name for product info on aimtec.com
Series AMEOR30-AZ
up to 2.5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 052.1e R3.L 2 of 14 North America only
Isolation Specifications
Parameters
Conditions
Typical
Rated
Units
Tested I/O voltage
3sec
3000
VAC
Isolation Resistance
>1000
MΩ
General Specifications
Parameters
Conditions
Typical
Maximum
Units
Switching frequency
130
KHz
Over current protection
AMEOR30-5070AZ
0.77
A
AMEOR30-4864AZ
0.68
AMEOR30-36100AZ
1.04
AMEOR30-24140AZ
1.45
AMEOR30-12250AZ
2.55
Over voltage protection
Refer to Constant Current vs. Constant Voltage Mode curve
Short circuit protection
Continuous
Short circuit restart
Auto recovery
Over temperature protection
>105°C
Operating temperature
With derating over 60°C
-40 to +80
oC
Maximum case temperature
100
oC
Storage temperature
-40 to +95
oC
Temperature coefficient
±0.02
% / oC
Cooling
Free air convection
Humidity
95
% RH
Wires
UL1015 18AWG * 20CM
Weight
220
g
Dimensions (L X H X W)
5.83 x 1.97 x 1.3 inches 148 x 50 x 33 mm
MTBF
>400,000 hrs (MIL-HDBK-217F at +25°C)
Environment Approval
Test
Parameters
Conditions
Shock
Wave form
Half sine wave
Acceleration amplitude
5gn
Bump duration
30 ms
Converter operation
Before and after test, body mounted (on chassis)
Number of bumps
18 (3 in each direction for every axis)
Vibration
Test mode
Sweep sine, 10-100Hz, speed 0.05Hz/s
Displacement
1 mm
Acceleration
3g, 3 loops 30min one cycle, 3h total, every axis tested
Converter operation
Before and after test, body mounted (on chassis)
Safety Specifications
Parameters
Agency approvals
CE
Standards
Designed to meet UL8750, IEC/EN60950-1 standards, EN55022, class B
Information Technology Equipment
EN55022 Class B
Harmonic Current Emissions
IEC/EN 61000-3-2, Class C
Voltage fluctuations and flicker
IEC/EN 61000-3-3, (EN60555-3)
Electrostatic Discharge Immunity
IEC 61000-4-2 Level 3
RF, Electromagnetic Field Immunity
IEC 61000-4-3 Level 2
Electrical Fast Transient / Burst Immunity
IEC 61000-4-4 Level 2
Surge Immunity
IEC 61000-4-5 Level 3
RF, Conducted Disturbance Immunity
IEC 61000-4-6 Level 2
Power frequency Magnetic Field Immunity
IEC 61000-4-8 Level 1
Voltage dips, Short Interruptions Immunity
IEC 61000-4-11
Series AMEOR30-AZ
up to 2.5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 052.1e R3.L 3 of 14 North America only
Dimensions
NOTE: to adjust the output current connect a 20K Ohm pot between blue and white wire
Wire connection:
AMEOR30-AZ Analog (resistive) Dimming Application Circuit
AMEPR30-AZ
N
1st LED
+Vout
1
1
-Vout
RED
BLACK
AC
BLUE
L
BROWN
GREEN
BLUE
WHITE Pot
Wire
Connection
Brown
AC L
Blue
AC N
Green
Ground
Red
+V output
Black
-V Output
Blue (Dimming)
+ Vs dimming
White (Dimming)
-Vs dimming
Model Number
Maximum Pot
Value (kΩ)
AMEPR30-5070AZ
9.00
AMEPR30-4864AZ
9.00
AMEPR30-36100AZ
9.00
AMEPR30-24140AZ
26.00
AMEPR30-12250AZ
26.10
148.00
(5.83)
Top View
Side View
28.00
(1.10)
50.00
(1.97)
5.00
(0.20)
4.50
(0.18)
4.50
(0.18)
4 Mounting Holes-M3
139.00
(5.47)
41.00
(1.61)
200.00
(8.00)
200.00
(8.00)
Input/Output Wires are 18 AWG 20cm
Series AMEOR30-AZ
up to 2.5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 052.1e R3.L 4 of 14 North America only
AMEOR30-AZ Analog (0-10V) Dimming Application Circuit
AMEOR30-AZ PWM (1KHz) Dimming Application Circuit
Temperature graph
-40 -20 0 20 40 60 80 100
100
80
60
40
20
0
Free Air Convection
55 º C
Safe Operating Area
Ambient Temperature º C
85
Series AMEOR30-AZ
up to 2.5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 052.1e R3.L 5 of 14 North America only
Efficiency Vs. Input Voltage & Output Current (Constant current load)
AMEOR30-5070AZ
AMEOR30-4864AZ
73.8
86.4
68.2
86.2
0.0
10.0
20.0
30.0
40.0
50.0
60.0
70.0
80.0
90.0
100.0
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
(%)
(A)
Efficiency Vs. Input Voltage & Output Current
110Vac
230Vac
Series AMEOR30-AZ
up to 2.5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 052.1e R3.L 6 of 14 North America only
Efficiency Vs. Input Voltage & Output Current (Constant current load)
(continued)
AMEOR30-36100AZ
AMEOR30-24140AZ
81.4
88.0
74.6
87.9
72.0
74.0
76.0
78.0
80.0
82.0
84.0
86.0
88.0
90.0
0.0 0.2 0.4 0.6 0.8 1.0 1.2
(%)
(A)
Efficiency Vs. Input Voltage & Output Current
110Vac
230Vac
81.6
86.6
79.4
87.5
78.0
79.0
80.0
81.0
82.0
83.0
84.0
85.0
86.0
87.0
88.0
0.0 0.5 1.0 1.5 2.0
(%)
(A)
Efficiency Vs. Input Voltage & Output Current
110Vac
230Vac
Series AMEOR30-AZ
up to 2.5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 052.1e R3.L 7 of 14 North America only
Efficiency Vs. Input Voltage & Output Current (Constant current load)
(continued)
AMEOR30-12250AZ
PFC Value vs. Output Load Current (constant current mode)
AMEOR30-5070AZ
Series AMEOR30-AZ
up to 2.5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 052.1e R3.L 8 of 14 North America only
PFC Value vs. Output Load Current (constant current mode)
(continued)
AMEOR30-4864AZ
AMEOR30-36100AZ
0.98 1.00
0.77
0.94
0.00
0.20
0.40
0.60
0.80
1.00
1.20
50% 60% 70% 80% 90% 100%
(Value)
(load)
PFC value Vs. Output Load Current
110Vac
230Vac
0.98
0.99
0.88
0.96
0.86
0.88
0.90
0.92
0.94
0.96
0.98
1.00
1.02
50% 60% 70% 80% 90% 100%
(Value)
(load)
PFC value Vs. Output Load Current
110Vac
230Vac
Series AMEOR30-AZ
up to 2.5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 052.1e R3.L 9 of 14 North America only
PFC Value vs. Output Load Current (constant current mode)
(continued)
AMEOR30-24140AZ
AMEOR30-12250AZ
0.98
1.00
0.91
0.96
0.90
0.91
0.92
0.93
0.94
0.95
0.96
0.97
0.98
0.99
1.00
1.01
50% 60% 70% 80% 90% 100%
(Value)
(load)
PFC value Vs. Output Load Current
110Vac
230Vac
0.98 1.00
0.77
0.94
0.00
0.20
0.40
0.60
0.80
1.00
1.20
50% 60% 70% 80% 90% 100%
(Value)
(load)
PFC value Vs. Output Load Current
110Vac
230Vac
Series AMEOR30-AZ
up to 2.5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 052.1e R3.L 10 of 14 North America only
Constant Current vs. Constant Voltage Mode
AMEOR30-5070AZ
AMEOR30-4864AZ
36 50
50.4 52
0.00
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
36 38 40 42 44 46 48 50 52 54 (V)
(A)
Constant Current Vs. Constant Voltage
Normal Input
36
48
48.4 50
0.00
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
36 38 40 42 44 46 48 50 52
(A)
(V)
Constant Current Vs. Constant Voltage
Normal
Input
Series AMEOR30-AZ
up to 2.5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 052.1e R3.L 11 of 14 North America only
Constant Current vs. Constant Voltage Mode
(continued)
AMEOR30-36100AZ
AMEOR30-24140AZ
24 36
36.4 38
0.00
0.20
0.40
0.60
0.80
1.00
1.20
24 26 28 30 32 34 36 38 40
(A)
(V)
Constant Current Vs. Constant Voltage
Normal
Input
12.0 24.0
24.7 26.0
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
12 14 16 18 20 22 24 26 28 (V)
(A) Constant Current Vs Constant Voltage
115 & 230
Vac
Series AMEOR30-AZ
up to 2.5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 052.1e R3.L 12 of 14 North America only
Constant Current vs. Constant Voltage Mode
(continued)
AMEOR30-12250AZ
Dimming Control (Output Current vs. Radj)
AMEOR30-5070AZ
5 12
12.3 14
0.00
0.50
1.00
1.50
2.00
2.50
3.00
5 7 9 11 13 15
(A)
(V)
Constant Current Vs. Constant Voltage
Normal
Input
0.007
0.01
0.01
0.02
0.07
0.15
0.25
0.45
0.79 1.66 9.00
0%
20%
40%
60%
80%
100%
120%
0 2 4 6 8 10 K(Ω)
(A) Output Current vs. Resistance adjustment
Normal Input
Series AMEOR30-AZ
up to 2.5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 052.1e R3.L 13 of 14 North America only
Dimming Control (Output Current vs. Radj)
(continued)
AMEOR30-4864AZ
AMEOR30-36100AZ
0.000
0.01
0.02
0.10
0.14
0.25
0.45
0.88
1.50
4.26
0%
20%
40%
60%
80%
100%
120%
0246810
(A)
K(Ω)
Output Current vs Resistance adjustment
Normal
Input
0.007
0.01
0.02
0.02
0.07
0.15
0.25
0.45
0.79
1.66
9.00
0%
20%
40%
60%
80%
100%
120%
0246810
(A)
K(Ω)
Output Current vs Resistance adjustment
Normal
Input
Series AMEOR30-AZ
up to 2.5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 052.1e R3.L 14 of 14 North America only
Dimming Control (Output Current vs. Radj)
(continued)
AMEOR30-24140AZ
AMEOR30-12250AZ
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com..
0.00
0.01
0.02
0.10
0.15
0.25
0.45
0.88
1.50 4.26
26.00
0%
20%
40%
60%
80%
100%
120%
0 5 10 15 20 25 30
(A)
K(Ω)
Output Current vs Resistance adjustment
Normal
Input
0.00
0.00
0.00
0.00
0.11
0.35
0.50
0.88
1.84
4.29
26.10
0%
20%
40%
60%
80%
100%
120%
0 5 10 15 20 25 30
(A)
K(Ω)
Output Current vs Resistance adjustment
Normal
Input
