D/CRCW-IF e3 www.vishay.com Vishay Pulse Proof Thick Film Chip Resistors FEATURES * High pulse performance, up to 10 kW * Stability R/R 1 % for 1000 h at 70 C * AEC-Q200 qualified * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 STANDARD ELECTRICAL SPECIFICATIONS LIMITING ELEMENT VOLTAGE Umax. ACRMS/DC V TEMPERATURE COEFFICIENT ppm/K CASE SIZE IMPERIAL CASE SIZE METRIC POWER RATING P70 W D10/CRCW0402-IF 0402 RR1005M 0.063 50 200 D11/CRCW0603-IF 0603 RR1608M 0.10 75 200 D12/CRCW0805-IF 0805 RR2012M 0.125 150 200 D25/CRCW1206-IF 1206 RR3216M 0.25 200 200 CRCW1210-IF 1210 RR3225M 0.50 200 200 CRCW2010-IF 2010 RR5025M 0.75 400 200 CRCW2512-IF 2512 RR6332M 1.0 500 200 TYPE TOLERANCE % 5 10 5 10 5 10 5 10 5 10 5 10 5 10 RESISTANCE RANGE SERIES 1.0 to 100K E24 1.0 to 100K E24 1.0 to 100K E24 1.0 to 100K E24 1.0 to 100K E24 1.0 to 100K E24 1.0 to 100K E24 Notes * These resistors do not feature a limited lifetime when operated within the limits of rated dissipation, permissible operating voltage, and permissible film temperature. However, the resistance typically increase due to the resistor's film temperature over operating time, generally known as drift. The drift may exceed the stability requirements of an individual application circuit and thereby limits the functional time. * Marking: See data sheet "Surface Mount Resistor Marking" (document number 20020). * Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material. TECHNICAL SPECIFICATIONS PARAMETER UNIT D10/ D11/ D12/ D25/ CRCW1210-IF CRCW2010-IF CRCW2512-IF CRCW0402-IF CRCW0603-IF CRCW0805-IF CRCW1206-IF Rated dissipation P70 (1) W 0.063 0.1 0.125 0.25 0.5 0.75 1.0 Operating voltage Umax. ACRMS/DC V 50 75 150 200 200 400 500 Insulation voltage Uins (1 min) V 75 100 200 300 300 300 300 16 25.5 40.5 Insulation resistance > 109 Operating temperature range C -55 to +155 Failure rate h-1 < 0.1 x 10-9 Mass mg 0.65 2 5.5 10 Note (1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printe-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 C is not exceeded. Revision: 17-Mar-15 Document Number: 20024 1 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-IF e3 www.vishay.com Vishay PART NUMBER AND PRODUCT DESCRIPTION Part Number: CRCW08051R00JNEAIF C R C W 0 8 0 5 1 R 0 0 J N E A I F TYPE VALUE TOLERANCE TCR PACKAGING SPECIAL CRCW0402 CRCW0603 CRCW0805 CRCW1206 CRCW1210 CRCW2010 CRCW2512 R = Decimal K = Thousand J=5% K = 10 % N = 200 ppm/K EA, EB, EC, ED, EE, EF, EG, EH, EI, EL Up to 2 digits IF = Pulse proof Product Description: D12/CRCW0805-IF 200 1R0 5 % ET1 e3 D12/CRCW0805-IF 200 1R0 5% ET1 e3 TYPE TCR RESISTANCE VALUE TOLERANCE PACKAGING LEAD (Pb)-FREE D10/CRCW0402-IF D11/CRCW0603-IF D12/CRCW0805-IF D25/CRCW1206-IF CRCW1210-IF CRCW2010-IF CRCW2512-IF 200 ppm/K 1R0 = 1 10K = 10 k 5% 10 % ET1, ET2, ET3, ET4, ET5, ET6, ET7, ET8, ET9, EF4, E02, E67, E82 e3 = Pure tin termination finish PACKAGING TYPE D10/CRCW0402-IF D11/CRCW0603-IF D12/CRCW0805-IF D25/CRCW1206-IF CRCW1210-IF CRCW2010-IF CRCW2512-IF Revision: 17-Mar-15 CODE QUANTITY ED = ET7 10 000 EE = EF4 50 000 EI = ET2 5000 ED = ET3 10 000 EL = ET4 20 000 EE = ET8 50 000 EA = ET1 5000 EB = ET5 10 000 EC = ET6 20 000 EA = ET1 5000 EB = ET5 10 000 EC = ET6 20 000 EA = ET1 5000 EB = ET5 10 000 EC = ET6 20 000 EA = ET1 5000 EB = ET5 10 000 EC = ET6 20 000 EF = E02 4000 EG = E67 2000 EH = E82 4000 CARRIER TAPE WIDTH PITCH 8 mm 2 mm REEL DIAMETER 180 mm/7" 330 mm/13" 180 mm/7" 8 mm 2 mm 180 mm/7" 285 mm/11.25" 330 mm/13" 180 mm/7" 8 mm 4 mm Paper tape acc. to IEC 60286-3 Type 1a 285 mm/11.25" 330 mm/13" 180 mm/7" 8 mm 4 mm 285 mm/11.25" 330 mm/13" 180 mm/7" 8 mm 4 mm 285 mm/11.25" 330 mm/13" 180 mm/7" 8 mm 4 mm 12 mm 4 mm 285 mm/11.25" 330 mm/13" Pressed tape acc. to IEC 60286-3 Type 1b 12 mm 8 mm 4 mm 180 mm/7" 180 mm/7" Document Number: 20024 2 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-IF e3 www.vishay.com Vishay DIMENSIONS in millimeters L T2 b I W a H T1 SIZE RECOMMENDED SOLDER PAD DIMENSIONS DIMENSIONS T1 WAVE SOLDERING IMPERIAL METRIC L W T2 a b l 0402 RR1005M 1.0 0.05 0.5 0.05 0.35 0.05 0.25 0.05 0.2 0.1 0.4 0.6 0.5 0603 RR1608M 1.55 0.85 0.1 0.45 0.05 0.3 0.2 0.5 0.9 0.3 0.2 0.7 + 0.10 - 0.05 H REFLOW SOLDERING 0.3 0.2 + 0.20 - 0.10 a b l 1.0 0.9 0.9 1.0 1.3 1.2 0.9 1.3 1.3 0805 RR2012M 2.0 + 0.20 - 0.10 1.25 0.15 0.45 0.05 1206 RR3216M 3.2 + 0.10 - 0.20 1.6 0.15 0.55 0.05 0.45 0.2 0.4 0.2 0.9 1.7 2.0 1.1 1.7 2.3 1210 RR3225M 3.2 0.2 2.5 0.2 0.55 0.05 0.45 0.2 0.4 0.2 0.9 2.5 2.0 1.1 2.5 2.2 2010 RR5025M 5.0 0.15 2.5 0.15 0.6 0.1 0.6 0.2 0.6 0.2 1.0 2.5 3.9 1.2 2.5 3.9 2512 RR6332M 6.3 0.2 3.15 0.15 0.6 0.1 0.6 0.2 0.6 0.2 1.0 3.2 5.2 1.2 3.2 5.2 0.3 FUNCTIONAL PERFORMANCE Pulse Power (W) Maximum pulse dissipation as a function of the pulse duration, single pulse 100 000 2512 2010 1210 1206 0805 0603 0402 10 000 1000 100 10 1 0.1 0.01 0.000001 0.00001 0.0001 0.001 0.01 0.1 1 10 100 Pulse Duration (s) Maximum pulse load, single pulse; applicable if P 0 and n 1000 and U Umax.; for permissible resistance change equivalent to 8000 h operation Revision: 17-Mar-15 Document Number: 20024 3 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-IF e3 www.vishay.com Vishay Pulse Power (W) Maximum pulse dissipation as a function of the pulse duration, continuous pulse loading 100 000 2512 2010 1210 1206 0805 0603 0402 10 000 1000 100 10 1 0.1 0.01 0.000001 0.00001 0.0001 0.001 0.01 0.1 1 10 100 Pulse Duration (s) Pulse Voltage U max. (V) Maximum pulse load, continuous pulses; applicable if P P (amb) and U Umax.; for permissible resistance change equivalent to 8000 h operation 2000 1800 2512 1600 1400 2010 1200 1000 800 1206/1210 600 400 0805 0603 200 0402 0 -6 10 10- 5 10- 4 10- 3 10- 2 10- 1 1 10 Pulse Duration t i (s) Maximum pulse voltage, single and continuous pulses; applicable if P Pmax.; for permissible resistance change equivalent to 8000 h operation Revision: 17-Mar-15 Document Number: 20024 4 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-IF e3 www.vishay.com Vishay Peak Voltage (V) Single-pulse high voltage overload test 1.2 s/50 s EN 140000 4.27 10 000 2512 2010 1210 1206 0805 0603 0402 1000 100 10 1 1 10 100 1000 10 000 100 000 Resistance Value () Pulse load rating in accordance to EN 60115-1, 4.27; 1.2 s/50 s; 5 pulses at 12 s intervals; for permissible resistance change 1 % Peak Voltage (V) Single-pulse high voltage overload test 10 s/700 s EN 140000 4.27 10 000 2512 2010 1210 1206 0805 0603 0402 1000 100 10 1 1 10 100 1000 10 000 100 000 Resistance Value () Pulse load rating in accordance to EN 60115-1, 4.27; 10 s/700 s; 10 pulses at 1 min intervals; for permissible resistance change 1 % Revision: 17-Mar-15 Document Number: 20024 5 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-IF e3 www.vishay.com Vishay Fraction of Rated Dissipation P70 (%) Derating 100 50 0 - 50 0 50 100 150 70 Ambient Temperature amb (C) TEST PROCEDURES AND REQUIREMENTS IEC EN 60082-2 60115-1 TEST CLAUSE METHOD PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (R) STABILITY CLASS 1 OR BETTER TEST Stability for product type: D/CRCW-IF e3 1 to 100 k 4.5 - Resistance - 5 %; 10 % 4.7 - Voltage proof U = 1.4 x Uins; 60 s No flashover or breakdown 4.13 - Short time overload U = 2.5 x P 70 x R 2 x Umax.; duration acc. to style (0.25 % R + 0.05 ) Solder bath method; Sn60Pb40; non-activated flux; (235 5) C, (2 0.2) s Good tinning ( 95 % covered); no visible damage Solder bath method; Sn96.5Ag3Cu0.5; non-activated flux; (245 5) C, (3 0.3) s Good tinning ( 95 % covered); no visible damage (20/- 55/20) C and (20/125/20) C 200 ppm/K 4.17.2 4.8.4.2 58 (Td) - Solderability Temperature coefficient 30 min. at - 55 C; 30 min. at 125C 4.19 14 (Na) Rapid change of temperature 5 cycles 1000 cycles Revision: 17-Mar-15 (0.25 % R + 0.05 ) (1 % R + 0.05 ) Document Number: 20024 6 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-IF e3 www.vishay.com Vishay TEST PROCEDURES AND REQUIREMENTS IEC EN 60082-2 60115-1 TEST CLAUSE METHOD PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (R) STABILITY CLASS 1 OR BETTER TEST Stability for product type: D/CRCW-IF e3 4.23 - Climatic sequence: - 4.23.2 2 (Ba) Dry heat 125 C; 16 h 4.23.3 30 (Db) Damp heat, cyclic 55 C; 90 % RH; 24 h; 1 cycle 4.23.4 1 (Aa) Cold - 55 C; 2 h 4.23.5 13 (M) Low air pressure 1 kPa; (25 10) C; 1 h 4.23.6 30 (Db) Damp heat, cyclic 55 C; 90 % RH; 24 h; 5 cycles 4.23.7 - DC load U= U= 1 to 100 k (1 % R + 0.05 ) P 70 x R P 70 x R Umax. 1.5 h on; 0.5 h off; 70 C; 1000 h 70 C; 8000 h 4.25.1 - Endurance at 70 C 4.18.2 58 (Td) Resistance to soldering heat Solder bath method (260 5) C; (10 1) s (0.25 % R + 0.05 ) 4.24 78 (Cab) Damp heat, steady state (40 2) C; (93 3) % RH; 56 days (1 % R + 0.05 ) 4.25.3 - Endurance at upper category temperature 155 C; 1000 h (1 % R + 0.05 ) 4.27 - Single pulse high voltage overload, 10 s/700 s U = 10 x P 70 x R 2 x Umax.; 10 pulses (1 % R + 0.05 ) (2 % R + 0.1 ) (1 % R + 0.05 ) All tests are carried out in accordance with the following specifications: * EN 60115-1, generic specification * EN 140400, sectional specification * EN 140401-802, detail specification * IEC 60068-2-x, environmental test procedures Packaging of components is done in paper or blister tapes according to IEC 60286-3. Revision: 17-Mar-15 Document Number: 20024 7 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000