MAC15-8G - LITTELFUSE - Product.Network

Speciﬁcations are subject to change without notice.

Revised: 07/02/19

Thyristors

Surface Mount – 400V - 800V > MAC15 Series

• Blocking Voltage to 800 V

• All Diffused and Glass

Passivated Junctions

for Greater Parameter

Uniformity and Stability

• Small, Rugged,

Thermowatt Construction

for Low Thermal

Resistance, High Heat

Dissipation and Durability

• Gate Triggering

Guaranteed in Three

Modes (MAC15 Series)

or Four Modes (MAC15A

Series)

• These Devices are

Pb−Free and are RoHS

Compliant

Features

Designed primarily for full-wave ac control applications,

such as solid−state relays, motor controls, heating controls

and power supplies; or wherever full−wave silicon gate

controlled solid−state devices are needed. Triac type

thyristors switch from a blocking to a conducting state

for either polarity of applied main terminal voltage with

positive or negative gate triggering.

Description

MAC15 Series

Additional Information

Samples

Resources

Datasheet

Functional Diagram

MT 1

MT 2

Pin Out

CASE 221A

STYLE 4

Speciﬁcations are subject to change without notice.

Revised: 07/02/19

Thyristors

Surface Mount – 400V - 800V > MAC15 Series

Rating Symbol Value Unit

Peak Repetitive Off-State Voltage (Note 1)

(Gate Open, Sine Wave 50 to 60 Hz, TJ = 25° to 100°C)

MAC15A6G

MAC15-8G, MAC15A8G

MAC15-10G, MAC15A10G

VDRM,

VRRM

400

600

800 V

On-State RMS Current (Full Cycle Sine Wave, 50 to 60 Hz, TC = 90°C) IT (RMS) 15 A

Peak Non-Repetitive Surge Current (One Full Cycle Sine Wave, 60 Hz, TJ = 125°C)

Preceded and Followed by Rated Current ITSM 150 A

Peak Gate Voltage

(Pulse Width ::: 1.0 µsec; TC = 90°C) VGM 10 V

Circuit Fusing Consideration (t = 8.3 ms) I2t 93 A²sec

Peak Gate Power

(TC = +80°C, Pulse Width = 1.0 µs) PGM 20 W

Peak Gate Current

(Pulse Width ::: 1.0 µsec; TC = 90°C) IGM 2.0 A

Average Gate Power (t = 8.3 ms, TC = 80°C) PG (AV) 0.5 W

Operating Junction Temperature Range TJ-40 to +125 °C

Storage Temperature Range Tstg -40 to +150 °C

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied.

Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.

1. VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative

potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded.

Maximum Ratings (TJ = 25°C unless otherwise noted)

Thermal Characteristics

Rating Symbol Value Unit

Thermal Resistance, Junction−to−Case (AC)

Junction−to−Ambient RƟJC

RƟJA

2.0

62.5 °C/W

Maximum Lead Temperature for Soldering Purposes, 1/8” from case for

10 seconds TL260 °C

2. Indicates Pulse Test: Pulse Width ≤ 2.0 ms, Duty Cycle ≤ 2%.

Characteristic Symbol Min Ty p Max Unit

Peak On−State Voltage (Note 2) (ITM = ±21 A Peak) VTM −1.3 1. 6 V

Gate Trigger Current

(Continuous dc)

(VD = 12 V, RL = 100 Ω)

MT2(+), G(+)

IGT

_ _ 50

MT2(+), G(−) _ _ 50

MT2(−), G(−) _ _ 50

MT2(–), G(+) 75

Gate Trigger Voltage

(Continuous dc)

(VD = 12 V, RL = 100 Ω)

MT2(+), G(+)

VGT

0.5 0.62 1.3

MT2(+), G(−) 0.5 0.57 1. 3

MT2(−), G(−) 0.5 0.65 1. 3

MT2(–), G(+) 0.5 0.74 1.3

Gate Non−Trigger Voltage

(TJ = 125°C)

(VD = 12 V, RL = 100 Ω)

MT2(+), G(+)

VGD

0.2 − −

MT2(+), G(−) 0.2 − −

MT2(−), G(−) 0.2 − −

MT2(–), G(+) 0.2 − −

Holding Current (VD = 12 Vdc, Gate Open, Initiating Current = ±200 mA)) IH– 6.0 40 mA

Electrical Characteristics - ON (TJ = 25°C unless otherwise noted; Electricals apply in both directions)

Electrical Characteristics - OFF (TJ = 25°C unless otherwise noted ; Electricals apply in both directions)

Characteristic Symbol Min Ty p Max Unit

Peak Repetitive Blocking Current

(VD = VDRM = VRRM; Gate Open) TJ = 25°C

TJ = 125°C IDRM,

IRRM

- - 1.0 mA

- - 2.0

Speciﬁcations are subject to change without notice.

Revised: 07/02/19

Thyristors

Surface Mount – 400V - 800V > MAC15 Series

Voltage Current Characteristic of SCR

Quadrant Deﬁnitions for a Triac

Symbol Parameter

VDRM Peak Repetitive Forward Off State Voltage

IDRM Peak Forward Blocking Current

VRRM Peak Repetitive Reverse Off State Voltage

IRRM Peak Reverse Blocking Current

VTM Maximum On State Voltage

IHHolding Current

+C urrent

+V oltage

VTM

IDR M at VDR M

on stat e

off stat e

IRR M at VRR M

Quadrant 1

Main Terminal 2 +

Quadrant 3

Main Terminal 2 VTM

All polarities are referenced to MT1.

With in phase signals (using standard AC lines) quadrants I and III are used

MT 1

(+) IGT

GA TE

(+) MT 2

RE F

MT 1

() IGT

GA TE

(+) MT 2

RE F

MT 1

(+) IGT

GA TE

() MT 2

RE F

MT 1

() IGT

GA TE

() MT 2

RE F

MT2 NEGA TIVE

(Negative Half Cycle)

MT2 POSITIVE

(Positive Half Cycle)

VItnardauQIIItnardauQ

ItnardauQIItnardauQ

IGT +I GT

Dynamic Characteristics

Characteristic Symbol Min Ty p Max Unit

Critical Rate of Rise of Commutation Voltage (VD = Rated VDRM, ITM = 21 A, Commutating

di/dt = 7.6 A/ms, Gate Unenergized, TC = 80°C) dV/dt − 5.0 − V/µs

Speciﬁcations are subject to change without notice.

Revised: 07/02/19

Thyristors

Surface Mount – 400V - 800V > MAC15 Series

Figure 4. Typical Gate Trigger CurrentFigure 3. Typical Gate Trigger Voltage

Figure 1. RMS Current Derating Figure 2. On−State Power Dissipation

Speciﬁcations are subject to change without notice.

Revised: 07/02/19

Thyristors

Surface Mount – 400V - 800V > MAC15 Series

Figure 6. Typical Holding Current

Figure 7. Maximum Non−Repetitive Surge Current

Figure 5. On−State Characteristics

Figure 8. Thermal Response

0.5

0.1

0.05

0.02

0.01

0.10 .2 0.51

ZJC(t) = r(t)

∞ R JC

0.2

25 10 20 50 1002 00 5001 k2 k5 k1 0 k

r(t) TRANSIENT THERMAL RESISTANCE

(NORMALIZED)

Speciﬁcations are subject to change without notice.

Revised: 07/02/19

Thyristors

Surface Mount – 400V - 800V > MAC15 Series

Device Device

Marking Package Shipping

MAC15−8G MAC15−8

TO-220AB

(Pb-Free) 500 Units/Box

MAC15−10G MAC1510

MAC15A6G MAC15A6

MAC15A8G MAC15A8

MAC15A10G MAC15A10

Dimensions Part Marking System

12 3

SEATING

PLANE

Pin Assignment

1Main Terminal 1

2Main Terminal 2

3 Gate

4 No Connection

Ordering Information

TO 220AB

CASE 221A

STYLE 12

123

1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE

ALLOWED.

Dim Inches Millimeters

Min Max Min Max

A0.590 0.620 14.99 15.75

B0.380 0.420 9.65 10.67

C0.178 0.188 4.52 4.78

D0.025 0.035 0.64 0.89

F0.142 0.147 3.61 3.73

G0.095 0.105 2.41 2.67

H0.110 0.130 2.79 3.30

J0.018 0.024 0.46 0.61

K0.540 0.575 13.72 14.61

L0.060 0.075 1.52 1.91

N0.195 0.205 4.95 5.21

Q0.105 0.115 2.67 2.92

R0.085 0.095 2.16 2.41

S0.045 0.060 1.14 1.52

T0.235 0.255 5.97 6.47

U0.000 0.050 0.00 1.27

V0.045 --- 1.15 ---

Z--- 0.080 --- 2.04

Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and

test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications.

Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics.

MAC15xxG

YMAXX

xx =See Table on Page 2

Y =Year

M =Month

A =Assembly Site

XX =Lot Serial Code

G =Pb-Free Package