Thyristors Surface Mount - 400V - 800V > MAC15 Series MAC15 Series Pb Description Designed primarily for full-wave ac control applications, such as solid-state relays, motor controls, heating controls and power supplies; or wherever full-wave silicon gate controlled solid-state devices are needed. Triac type thyristors switch from a blocking to a conducting state for either polarity of applied main terminal voltage with positive or negative gate triggering. Features * Blocking Voltage to 800 V * All Diffused and Glass Passivated Junctions for Greater Parameter Uniformity and Stability * Small, Rugged, Thermowatt Construction for Low Thermal Resistance, High Heat Dissipation and Durability * Gate Triggering Guaranteed in Three Modes (MAC15 Series) or Four Modes (MAC15A Series) * These Devices are Pb-Free and are RoHS Compliant Functional Diagram Pin Out MT 2 MT 1 G CASE 221A STYLE 4 1 Additional Information 2 Datasheet Resources Samples (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/02/19 Thyristors Surface Mount - 400V - 800V > MAC15 Series Maximum Ratings (TJ = 25C unless otherwise noted) Rating Peak Repetitive Off-State Voltage (Note 1) (Gate Open, Sine Wave 50 to 60 Hz, TJ = 25 to 100C) Symbol Value Unit VDRM, VRRM 400 600 800 V 15 A MAC15A6G MAC15-8G, MAC15A8G MAC15-10G, MAC15A10G On-State RMS Current (Full Cycle Sine Wave, 50 to 60 Hz, TC = 90C) IT (RMS) Peak Non-Repetitive Surge Current (One Full Cycle Sine Wave, 60 Hz, TJ = 125C) Preceded and Followed by Rated Current ITSM 150 A Peak Gate Voltage (Pulse Width ::: 1.0 sec; TC = 90C) VGM 10 V I2t 93 Asec Peak Gate Power (TC = +80C, Pulse Width = 1.0 s) PGM 20 W Peak Gate Current (Pulse Width ::: 1.0 sec; TC = 90C) IGM 2.0 A Circuit Fusing Consideration (t = 8.3 ms) Average Gate Power (t = 8.3 ms, TC = 80C) PG (AV) 0.5 W Operating Junction Temperature Range TJ -40 to +125 C Storage Temperature Range Tstg -40 to +150 C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1.VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. Thermal Characteristics Rating Symbol Value Unit RJC RJA 2.0 62.5 C/W TL 260 C Junction-to-Case (AC) Junction-to-Ambient Thermal Resistance, Maximum Lead Temperature for Soldering Purposes, 1/8" from case for 10 seconds Electrical Characteristics - OFF (TJ = 25C unless otherwise noted ; Electricals apply in both directions) Characteristic Peak Repetitive Blocking Current (VD = VDRM = VRRM; Gate Open) Symbol Min IDRM, IRRM - - 1.0 - - 2.0 TJ = 25C TJ = 125C Typ Max Unit mA Electrical Characteristics - ON (TJ = 25C unless otherwise noted; Electricals apply in both directions) Characteristic Peak On-State Voltage (Note 2) (ITM = 21 A Peak) Gate Trigger Current (Continuous dc) (VD = 12 V, RL = 100 ) Gate Trigger Voltage (Continuous dc) (VD = 12 V, RL = 100 ) Gate Non-Trigger Voltage (TJ = 125C) (VD = 12 V, RL = 100 ) Symbol Min Typ Max Unit VTM - 1.3 1.6 V _ _ 50 MT2(+), G(+) MT2(+), G(-) MT2(-), G(-) IGT _ _ 50 _ _ 50 0.5 0.62 1.3 MT2(-), G(+) 75 MT2(+), G(+) MT2(+), G(-) MT2(-), G(-) VGT 0.5 0.57 1.3 0.5 0.65 1.3 1.3 MT2(-), G(+) 0.5 0.74 MT2(+), G(+) 0.2 - - MT2(+), G(-) 0.2 - - 0.2 - - MT2(-), G(-) VGD MT2(-), G(+) Holding Current (VD = 12 Vdc, Gate Open, Initiating Current = 200 mA)) mA IH 0.2 - - - 6.0 40 V V mA 2.Indicates Pulse Test: Pulse Width 2.0 ms, Duty Cycle 2%. (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/02/19 Thyristors Surface Mount - 400V - 800V > MAC15 Series Dynamic Characteristics Characteristic Symbol Min Typ Max Unit Critical Rate of Rise of Commutation Voltage (VD = Rated VDRM, ITM = 21 A, Commutating di/dt = 7.6 A/ms, Gate Unenergized, TC = 80C) dV/dt - 5.0 - V/s Voltage Current Characteristic of SCR Symbol Parameter VDRM Peak Repetitive Forward Off State Voltage IDRM Peak Forward Blocking Current VRRM Peak Repetitive Reverse Off State Voltage IRRM Peak Reverse Blocking Current VTM Maximum On State Voltage IH +C urrent V TM on stat e I RR M at V RR M Holding Current Quadrant Definitions for a Triac IH Quadrant 3 Main Terminal 2 MT2 POSITIVE (Positive Half Cycle) + +V oltage I DR M at V DR M V TM MT 1 MT 1 RE F RE F ( ) MT 2 ( ) MT 2 I GT Q u a dr a n t III off stat e Q ua dr a nt I (+) I GT GA TE ( ) I GT GA TE IH (+) MT 2 (+) MT 2 Q u a dr a n t II Quadrant 1 Main Terminal 2 + +I GT Q u a dr a n t IV (+) I GT GA TE ( ) I GT GA TE MT 1 MT 1 RE F RE F MT2 NEGA TIVE (Negative Half Cycle) All polarities are referenced to MT1. With in phase signals (using standard AC lines) quadrants I and III are used (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/02/19 Thyristors Surface Mount - 400V - 800V > MAC15 Series Figure 1. RMS Current Derating Figure 2. On-State Power Dissipation Figure 3. Typical Gate Trigger Voltage Figure 4. Typical Gate Trigger Current (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/02/19 Thyristors Surface Mount - 400V - 800V > MAC15 Series Figure 5. On-State Characteristics Figure 6. Typical Holding Current Figure 7. Maximum Non-Repetitive Surge Current Figure 8. Thermal Response r(t) TRANSIENT THERMAL RESIST ANCE (NORMALIZED) 1 0.5 0.2 Z JC(t) = r(t) R JC 0.1 0.05 0.02 0.01 0.10 .2 0.51 25 10 20 50 1002 00 5001 k2 k5 k1 0k (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/02/19 Thyristors Surface Mount - 400V - 800V > MAC15 Series Dimensions Part Marking System 4 SEATING PLANE B F 4 Q 12 C T S A U 3 1 H 2 3 MAC15xxG YMAXX TO 220AB CASE 221A STYLE 12 K Z xx =See Table on Page 2 Y =Year M =Month A =Assembly Site XX =Lot Serial Code G =Pb-Free Package R L V J G D N Dim Inches Millimeters Pin Assignment Min Max Min Max 1 Main Terminal 1 A 0.590 0.620 14.99 15.75 2 Main Terminal 2 B 0.380 0.420 9.65 10.67 3 Gate C 0.178 0.188 4.52 4.78 4 No Connection D 0.025 0.035 0.64 0.89 F 0.142 0.147 3.61 3.73 G 0.095 0.105 2.41 2.67 H 0.110 0.130 2.79 3.30 J 0.018 0.024 0.46 0.61 K 0.540 0.575 13.72 14.61 L 0.060 0.075 1.52 1.91 N 0.195 0.205 4.95 5.21 Q 0.105 0.115 2.67 2.92 R 0.085 0.095 2.16 2.41 S 0.045 0.060 1.14 1.52 T 0.235 0.255 5.97 6.47 U 0.000 0.050 0.00 1.27 V 0.045 --- 1.15 --- Z --- 0.080 --- 2.04 Ordering Information MAC15-8G Device Marking MAC15-8 MAC15-10G MAC1510 MAC15A6G MAC15A6 Device MAC15A8G MAC15A8 MAC15A10G MAC15A10 Package Shipping TO-220AB (Pb-Free) 500 Units/Box 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2.CONTROLLING DIMENSION: INCH. 3.DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/02/19