Preliminary data
This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to
change without notice.
July 2009 Doc ID 15807 Rev 2 1/12
12
LPY530AL
MEMS motion sensor:
dual axis pitch and yaw ±300°/s analog gyroscope
Features
■2.7 V to 3.6 V single supply operation
■Very extended operating temperature range
(-40°C to +85°C)
■High stability overtemperature
■Absolute analog rate output
■Two separate outputs for each axis
(1x and 4x amplified)
■Integrated low-pass filters
■Low power consumption
■Embedded power-down
■Embedded self-test
■High shock and vibration survivability
■ECOPACK® RoHS and “Green” compliant
(see Section 5)
Applications
■Pointing devices, remote and game controllers
■Motion control with user interface
■GPS navigation systems
■Industrial and robotics
Description
The LPY530AL is a low-power two-axis
micromachined gyroscope able to measure
angular rate along pitch and yaw axes.
It provides excellent temperature stability and
high resolution over extended operating
temperature range (-40°C to +85°C).
The LPY530AL has a full scale of ±300 °/s and is
capable of detecting rates with a -3 dB bandwidth
up to 140 Hz. The gyroscope is the combination
of one actuator and one accelerometer integrated
in a single micromachined structure.
It includes a sensing element composed by single
driving mass, kept in continuos oscillating
movement and able to react when an angular rate
is applied based on the Coriolis principle.
A CMOS IC provides the measured angular rate
to the external world through an analog output
voltage, allowing high level of integration and
production trimming to better match sensing
element characteristics.
ST gyroscope family leverages on robust and
mature manufacturing process already used for
the production of micromachined accelerometers.
ST is already in the field with several hundreds
million sensors with excellent acceptance from
the market in terms of quality, reliability and
performance.
LPY530AL is provided in plastic land grid array
(LGA) package.
Several years ago ST pioneered successfully the
usage of this package for accelerometers. Today
ST has the widest manufacturing capability and
strongest expertise in the world for production of
sensor in plastic LGA package.
LGA-16L (5x5x1.5mm)
Table 1. Device summary
Order code Temperature range (°C) Package Packing
LPY530AL -40 to +85 LGA-16 (5x5x1.5) Tray
LPY530ALTR -40 to +85 LGA-16 (5x5x1.5) Tape and reel
www.st.com
Obsolete Product(s) - Obsolete Product(s)
Contents LPY530AL
2/12 Doc ID 15807 Rev 2
Contents
1 Block diagram and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Mechanical and electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Mechanical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3 Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 Zero-rate level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.3 Self-test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.4 High pass filter reset (HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4 Application hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1 Output response vs. rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2 Soldering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Obsolete Product(s) - Obsolete Product(s)
LPY530AL Block diagram and pin description
Doc ID 15807 Rev 2 3/12
1 Block diagram and pin description
Figure 1. Block diagram
1.1 Pin description
Figure 2. Pin connection
+
-
CLOCK
TRIMMING
CIRCUITS
REFERENCE
DEMODULATOR
CHARGE
AMPLIFIER
PHASE GENERATOR
SWITCHED
4xOUTX (amplified)
X/Z
LOW-PASS
CAPACITOR
FILTER
+Ω x
DRIVING MASS
DEMODULATOR
CHARGE
AMPLIFIER
SWITCHED
4xOUTZ (amplified)
LOW-PASS
CAPACITOR
FILTER
+Ω z
Optional
Filter
LP/HP
Optional
Filter
LP/HP
GAIN
GAIN
Not amplified
Not amplified
4x
4x
Feedback loop
+
-
filtered output X
filtered output Z
(TOP VIEW)
DIRECTION OF THE
DETECTABLE
ANGULAR RATES
GND
VCONT
FILTOUT Z/ OUT Z
FILTVDD
4xOUTX
Vref
FILTIN Z
ST
Vdd
Res
FILTIN X
FILTOUT X/ OUT X
HP
1614
6
8
9
13 1
5
(BOTTOM VIEW)
Res
4xOUTZ
PD
+Ω x
+Ω z
Obsolete Product(s) - Obsolete Product(s)
Block diagram and pin description LPY530AL
4/12 Doc ID 15807 Rev 2
Table 2. Pin description
Pin # Pin name Analog function
1 GND 0V supply voltage
2 FILTVDD PLL filter connection pin #2
3 VCONT PLL filter connection pin #1
4 OUTX Not amplified output
5 4xINX Input of 4x amplifier
6 4xOUTX X rate signal output voltage (amplified)
7 Vref Reference voltage
8 4xOUTZ Z rate signal output voltage (amplified)
9 4xINZ Input of 4x amplifier
10 OUTZ Not amplified output
11 ST Self-test (logic 0: normal mode; logic 1: self-test)
12 PD Power-down (logic 0: normal mode; logic 1: power-down
mode)
13 HP High pass filter reset (logic 0: normal operation mode;
logic1: external high pass filter is reset)
14,15 Res Reserved. Connect to Vdd
16 Vdd Power supply
Obsolete Product(s) - Obsolete Product(s)
LPY530AL Mechanical and electrical specifications
Doc ID 15807 Rev 2 5/12
2 Mechanical and electrical specifications
2.1 Mechanical characteristics
Table 3. Mechanical characteristics @ Vdd = 3 V, T = 25 °C unless otherwise noted(1)
Symbol Parameter Test condition Min. Typ.(2) Max. Unit
FSA Measurement range 4x OUT (amplified) ±300 °/s
FS OUT (not amplified) ±1200 °/s
SoA Sensitivity(3) 4x OUT (amplified) 3.33 mV/ °/s
So OUT (not amplified) 0.83 mV/ °/s
SoDr Sensitivity change vs
temperature Delta from 25°C 0.037 %/°C
Voff Zero-rate level(3) 1.23 V
Vref Reference voltage 1.23 V
OffDr Zero-rate level change
Vs temperature Delta from 25°C 0.05 °/s/°C
NL Non linearity Best fit straight line ±1 % FS
BW Bandwidth(4) 140 Hz
Rn Rate noise density 0.035 °/s /
Top Operating
temperature range -40 +85 °C
1. The product is factory calibrated at 3 V. The operational power supply range is specified in Table 4.
2. Typical specifications are not guaranteed
3. Sensitivity and Zero-rate Offset are not ratiometric to supply voltage
4. The product is capable of measuring angular rates extending from DC to the selected BW.
H
z
Obsolete Product(s) - Obsolete Product(s)
Mechanical and electrical specifications LPY530AL
6/12 Doc ID 15807 Rev 2
2.2 Electrical characteristics
2.3 Absolute maximum ratings
Stresses above those listed as “absolute maximum ratings” may cause permanent damage
to the device. This is a stress rating only and functional operation of the device under these
conditions is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
Table 4. Electrical characteristics @ Vdd =3 V, T=25 °C unless otherwise noted(1)
Symbol Parameter Test condition Min. Typ.(2) Max. Unit
Vdd Supply voltage 2.7 3 3.6 V
Idd Supply current PD pin connected to GND 6.8 mA
IddPdn Supply current in
power-down mode PD pin connected to Vdd 1 5 µA
VST Self-test input Logic 0 level 0 0.2*Vdd V
Logic 1 level 0.8*Vdd Vdd
VPD Power-down input Logic 0 level 0 0.2*Vdd V
Logic 1 level 0.8*Vdd Vdd
To p Operating temperature
range -40 +85 °C
1. The product is factory calibrated at 3 V
2. Typical specifications are not guaranteed
Table 5. Absolute maximum ratings
Symbol Ratings Maximum value Unit
Vdd Supply voltage -0.3 to 6 V
Vin Input voltage on any control pin (PD, ST) -0.3 to Vdd +0.3 V
A Acceleration) 3000 g for 0.5 ms
10000 g for 0.1 ms
TSTG Storage temperature range -40 to +125 °C
ESD Electrostatic discharge protection 2 (HBM) kV
This is a mechanical shock sensitive device, improper handling can cause permanent
damage to the part
This is an ESD sensitive device, improper handling can cause permanent damage to
the part
Obsolete Product(s) - Obsolete Product(s)
LPY530AL Terminology
Doc ID 15807 Rev 2 7/12
3 Terminology
3.1 Sensitivity
An angular rate gyroscope is a device that produces a positive-going output voltage for
counterclockwise rotation around the sensible axis considered. Sensitivity describes the
gain of the sensor and can be determined by applying a defined angular velocity to it. This
value changes very little over temperature and time.
3.2 Zero-rate level
Zero-rate level describes the actual output signal if there is no angular rate present. Zero-
rate level of precise MEMS sensors is, to some extent, a result of stress to the sensor and
therefore zero-rate level can slightly change after mounting the sensor onto a printed circuit
board or after exposing it to extensive mechanical stress. This value changes very little over
temperature and time.
3.3 Self-test
Self-test allows testing the mechanical and electrical part of the sensor, allowing the seismic
mass to be moved by means of an electrostatic test-force. The Self-test function is off when
the ST pin is connected to GND. When the ST pin is tied to Vdd, an actuation force is
applied to the sensor, emulating a definite Coriolis force. In this case the sensor output will
exhibit a voltage change in its DC level which is also dependent on the supply voltage.
When ST is active, the device output level is given by the algebraic sum of the signals
produced by the velocity acting on the sensor and by the electrostatic test-force. If the output
signals change within the amplitude specified in Table 3, then the mechanical element is
working properly and the parameters of the interface chip are within the defined
specification.
3.4 High pass filter reset (HP)
LPY530AL provides the possibility to reset the optional external high pass filter by applying
high logic value to HP pad. This procedure ensures faster response expecially during
overload conditions. Moreover, this operation is suggested each time the device is powered.
Obsolete Product(s) - Obsolete Product(s)
Application hints LPY530AL
8/12 Doc ID 15807 Rev 2
4 Application hints
Figure 3. LPY530AL electrical connections and external components values
Power supply decoupling capacitors (100 nF ceramic or polyester + 10 µF Aluminum)
should be placed as near as possible to the device (common design practice).
The LPY530AL allows band limiting the output rate response through the use of an external
low pass filter (suggested) and/or high pass filter (optional) in addition to the embedded low
pass filter (ft = 140 Hz).
4xOUTX and 4xOUTZ are respectively OUTX and OUTZ amplified outputs lines, internally
buffered to ensure low output impedance.
If external high pass or low pass filtering is not applied it is mandatory to short-circuit
respectively pad 4 to pad 5 and pad 9 to pad 10 when amplified outputs are used.
When only not-amplified output are used (OUTX/Z), it is suggested to set pads 5 and 9 to
fixed reference voltage (Vref).
When high pass filter is applied to not amplified output (OUTx), it is recommended to buffer
the line before entering ADC for performance optimization.
The LPY530AL IC includes a PLL (phase locked loop) circuit to synchronize driving and
sensing interfaces. Capacitors and resistors must be added at FILTVDD and VCONT pins
(as shown in Figure 3) to implement a low-pass filter.
100 nF
10kOhm 470nF
Vdd
GND
HP
Vref
4xOUTX
C2
R1 C1
GND
10 µF
GND
Recomended
Low-pass filter
LPY530AL
(Top View)
1
16 14
13
9
86
5
10nF
PD
ST
GND
Vref
4xOUTZ
Optional
High-pass filter
Vref GND
Typical values:
C1
R1
C2
R2 C1
R1 C2
R2
R1 = 1MOhm
C1 = 4.7 uF
R2 = 33kOhm
C2 = 2.2nF to 2.2uF
Not amplified
(TOP VIEW)
DIRECTION OF THE
DETECTABLE
ANGULAR RATES
+Ω
x
+Ω
z
filtered output X
Not amplified
filtered output Z
Obsolete Product(s) - Obsolete Product(s)
LPY530AL Application hints
Doc ID 15807 Rev 2 9/12
4.1 Output response vs. rotation
Figure 4. Output response vs. rotation
4.2 Soldering information
The LGA package is compliant with the ECOPACK®, RoHS and “Green” standard.
It is qualified for soldering heat resistance according to JEDEC J-STD-020C.
Leave “pin 1 indicator” unconnected during soldering.
Land pattern and soldering recommendations are available at www.st.com
+Ω x
Steady State position:
4xOUTX = 4xOUTZ = 1.23V
OUTX = OUTZ = 1.23V
+Ω x
+Ω z
+Ω z
Positive rotations as indicated by arrows
+300°/sec --> 4xOUTX, 4xOUTZ = 1.23V + SoA*300 = 2.23V
+300°/sec --> OUTX, OUTZ = 1.23V + So*300 = 1.48V
increase output value over Zero rate level:
Obsolete Product(s) - Obsolete Product(s)
Package information LPY530AL
10/12 Doc ID 15807 Rev 2
5 Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Figure 5. LGA-16: mechanical data and package dimensions
A1 1.46 1.5 1.6 0.057 0.059 0.063
A2 1.33 0.052
A30.16 0.2 0.24 0.006 0.0080.009
C0.30.012
D1 4.85 5 5.15 0.191 0.197 0.203
E1 4.85 5 5.15 0.191 0.197 0.203
L0.80.031
L1 3.2 0.126
M 1.6 0.062
M1 2.15 2.175 2.20 0.0850.0860.087
M2 1.625 0.064
N 2.175 0.086
N1 2.4 0.094
T1 0.80.031
T2 0.475 0.5 0.525 0.019 0.020 0.021
R 1.2 1.6 0.047 0.063
S0.1 0.004
h 0.15 0.006
k 0.05 0.002
j 0.1 0.004
LGA-16 (5x5x1.5mm)
Land Grid Array Package
7887555A
Obsolete Product(s) - Obsolete Product(s)
LPY530AL
12/12 Doc ID 15807 Rev 2
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Obsolete Product(s) - Obsolete Product(s)
