PRELIMINARY NJW1164 AUDIO PROCESSOR with BBE GENERAL DESCRIPTION The NJW1164 is a TV audio processor with sound enhancement (BBE). The NJW1164 contains all necessary functions to process TV audio signal such as volume control, tone control, balance, mute, AGC and NJRC's proprietary surround sound process, eala. The eala reproduces a natural surround sound with clear vocal orientation. 2 The total modes and variables are controlled by the I C bus interface. PACKAGE OUTLINE NJW1164L NJW1164M FEATURES Operating Voltage 7.5 to 13V 2 I C BUS Interface BBE Sound Enhancement (Low Boost and High Boost: 15dB max.) eala (NJRC Original Surround) AGC Circuit (It reduces volume difference among input sources.) Simulated Surround Bi-CMOS Technology Package Outline SDIP30, SDMP30 BLOCK DIAGRAM VOL1 BBE TONE VOL2 I2C Bus Interface eala & Sim ulated Surround AGC VOL1 BBE TONE VOL2 Bias - 1 - NJW1164 PRELIMINARY PIN FUNCTION No. Symbol 1 INa 2 INb 30 BBE1a BBE1b 29 3 BBE2a BBE2b 28 4 BBEOUTa BBEOUTb 27 5 TONE INa TONE INb 26 6 TONE-Ha TONE-Hb 25 7 TONE-La TONE-Lb 24 8 OUTa OUTb 23 9 AGC SR-FIL 22 VREF 21 10 SS-FIL 11 CVB CTH 20 12 CVA CTL 19 13 SDA AUX0 18 14 SCL AUX1 17 15 GND Vcc 16 Function No Symbol Function 1 INa Ach Input 16 Vcc Power Supply Pin 2 BBE1a Ach BBE Filter1 (Process) 17 AUX1 Auxiliary Output1 3 BBE2a Ach BBE Filter2 (Lo Contour) 18 AUX0 Auxiliary Output0 4 BBE OUTa Ach Output for the Other Accessories 19 CTL Pop Noise reduction for Bass Control 5 TONE INa Ach Input From the Other Accessories 20 CTH Pop Noise reduction for Treble Control 6 TONE-Ha Ach Treble Filter 21 VREF 7 TONE-La Ach Bass Filter 22 SR-FIL Surround Filter 8 OUTa Ach Output 23 OUTb Bch Output 9 AGC 10 SS-FIL Reference Voltage AGC Filter 24 TONE-Lb Bch Bass Filter Simulated Stereo Filter 25 TONE-Hb Bch Treble Filter 11 CVB Pop Noise Reduction for Volume & Balance 26 TONE INb Bch Input from the Other Accessories 12 CVA Pop Noise Reduction for Volume & Balance 27 BBE OUTb Bch Output for the Other Accessories 13 SDA SDA Data Input (I2C BUS) 28 BBE2b 2 14 SCL SCL Data Input (I C BUS) 29 BBE1b 15 GND GND 30 INb -2- Bch BBE Filter2 (Process) Bch BBE Filter1 (Lo Contour) Bch Input PRELIMINARY NJW1164 ABSOLUTE MAXIMUM RATING (Ta=25C) PARAMETER SYMBOL + RATING UNIT 15 V Supply Voltage V Power Dissipation PD 700 mW Operating Temperature Range Topr -20 to +75 C Storage Temperature Range Tstg -40 to +125 C ELECTRICAL CHARACTERISTICS (Ta=25C, V+=9V, Rg=600, RL=47k, Vin=100mVrms/1kHz unless otherwise specified) PARAMETER SYMBOL TEST CONDITION + MIN. TYP. MAX. UNIT 7.5 9.0 13.0 V Operating Voltage V Supply Current ICC No Signal - 13 25 mA Reference Voltage VREF No Signal 4.0 4.5 5.0 V Maximum Input Voltage VIM VOL=-20dB,THD=1% 2.8 3.0 - Vrms Maximum Output Voltage VOM OUTPUT VOL=0dB,THD=1% - 2.5 - Vrms Channel Balance GCB VOL=0dB -1.5 0.0 1.5 dB Balance Boost A BABST CHS="0", BAL="11111" -2.0 0.0 2.0 dB Balance Cut A BACUT CHS="1", BAL="11111" Vin = 1Vrms - - -70 dB Balance Boost B BBBST CHS="1", BAL="11111" -2.0 0.0 2.0 dB Balance Cut B BBCUT - - -70 dB - - 0.5 % -2.0 0.0 2.0 dB - - -70 dB - - -70 dB - -90 (31.6) -106 (5.0) Logic Output: High 4.5 - 5.0 Logic Output: Low 0 - 0.3 Total Harmonic Distortion THD CHS="0", BAL="11111" Vin = 1Vrms Vo=0.5Vrms BW=400Hz to 30kHz Maximum Gain GVMAX VOL= 0dB Minimum Gain GVMIN VOL= MUTE Channel Separation CS Output Noise 1 VNO1 Output Noise 2 VNO2 AUX Output Voltage VAUX Vin = 2Vrms Ain Bout, Bin Aout VOL = 0dB BW=400Hz to 30kHz VOL = MUTE BW = 400Hz to 30kHz -85 (56.2) -96 (15.8) dBV (Vrms) dBV (Vrms) V BW: Band Width -3- NJW1164 PRELIMINARY TONE CONTROL PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT High Frequency Boost HFBST BCT="1", TREB="1111", f=10kHz 12.5 15.0 17.5 dB High Frequency Flat HFFLT TRBE="0000", f=10kHz -2.0 0.0 2.0 dB High Frequency Cut HFCUT BCT="0", TRBE="1111", f=10kHz -17.5 -15.0 -12.5 dB Low Frequency Boost LFBST BCB="1", BASS="1111", f=100Hz 12.5 15.0 17.5 dB Low Frequency Flat LFFLT BASS="0000", f=100Hz -2.0 0.0 2.0 dB Low Frequency Cut LFCUT BCB="0", BASS="1111", f=100Hz -17.5 -15.0 -12.5 dB SUB-TONE CONTROL PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT High Frequency Boost SHFBST BCST="1", SUB-TREB="11", f=10kHz 2.0 3.0 4.0 dB High Frequency Cut SHFCUT BCST="0", SUB-TREB="11", f=10kHz -4.0 -3.0 -2.0 dB Low Frequency Boost SLFBST BCSB="1", SUB-BASS="11", f=100Hz 2.0 3.0 4.0 dB Low Frequency Cut SLFCUT BCSB="0", SUB-BASS="11", f=100Hz -4.0 -3.0 -2.0 dB SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT AGC CONTROL PARAMETER AGC Boost AGCBST Vin=50mVrms, f=1kHz 1.5 3.5 5.5 dB AGC Flat1 AGCFLT1 Vin=150mVrms, f=1kHz -2.5 0.0 2.5 dB AGC Flat2 AGCFLT2 Vin=300mVrms, f=1kHz -2.5 0.0 2.5 dB AGC Flat3 AGCFLT3 Vin=400mVrms, f=1kHz -2.5 0.0 2.5 dB AGC Flat4 AGCFLT4 Vin=540mVrms, f=1kHz -2.5 0.0 2.5 dB AGC Cut AGCCUT Vin=2Vrms, f=1kHz -14 -10 -6.0 dB MIN. TYP. MAX. UNIT BBE PARAMETER SYMBOL TEST CONDITION BBE Low Frequency Boost Range BBELOW BBE-Low="1111", f = 50Hz - 15.0 - dB BBE High Frequency Boost Range BBEHIGH BBE-High="1111", f = 10KHz - 15.0 - dB MIN. TYP. MAX. UNIT 6.0 8.0 10.0 dB 1.6 3.6 5.6 dB 10.7 12.7 14.7 dB 8.4 10.4 12.4 dB 1.0 3.0 5.0 dB 1.0 3.0 5.0 dB SURROUND (SURROUND-ON) PARAMETER SYMBOL Surround Gain1 SRGAIN1 Surround Gain2 SRGAIN2 Surround Gain3 SRGAIN3 Surround Gain4 SRGAIN 4 Simulated Surround Gain1 SRSIM1 Simulated Surround Gain2 SRSIM2 -4- TEST CONDITION AinAout, f=100Hz SUR0="0", SUR="1" AinBout, f=100Hz SUR0="0", SUR="1" AinAout, f=100Hz SUR0="1", SUR="1" AinBout, f=100Hz SUR0="1", SUR="1" Ain+BinAout, f=1kHz SUR0="1", SUR="0" Ain+BinBout, f=1kHz SUR0="1", SUR="0" PRELIMINARY NJW1164 2 I C BUS BLOCK CHARACTERISTICS (SDA, SCL) PARAMETER SYMBOL MIN. TYP. MAX. UNIT High Level Input Voltage VIH 2.5 - 5.0 V Low Level Input Voltage VIL 0 - 1.5 V High Level Input Current IIH - - 10 A Low Level Input Current IIL - - 10 A Low Level Output Voltage (3mA at SDA pin) VOL 0 - 0.4 V Maximum Output Current IOL -3.0 - - mA Maximum Clock Frequency fSCL - - 100 kHz Data Change Minimum Waiting Time tBUF 4.7 - - s tHD:STA 4.0 - - s Low Level Clock Pulse Width tLOW 4.7 - - s High Level Clock Pulse Width THIGH 4.0 - - s Minimum Start Preparation Waiting Time tSU:STA 4.7 - - s Minimum Data Hold Time tHD:DAT 5.0 - - s Minimum Data Preparation Time tSU:DAT 250 - - ns Rise Time tR - - 1.0 s Fall Time tF - - 300 ns tSU:STO 4.0 - - s Data Transfer Start Minimum Waiting Time Minimum Stop Preparation Waiting Time 2 I C BUS Load Condition: Pull up resistance 4k (Connected to +5V) Load capacitance 200pF (Connected to GND) SDA tBUF tR tF tHD:STA SCL tHD:STA tLOW P S tHD:DAT tHIGH tSU:STA tSU:DAT Sr tSU:STO P -5- NJW1164 PRELIMINARY !TERMINAL DESCRIPTION No. SYMBOL FUNCTION EQUIVALENT CIRCUIT VOLTAGE V+ 1,30 pin 1 30 INa INb 20k Ach Input terminal Bch Input terminal V+/2 80k Vref 4 8 23 27 BBE OUTa OUTa OUTb BBE OUTb Ach Output for the Other Accessories Ach Output Bch Output Bch Output for the Other Accessories 50 SS-FIL Simulated Stereo Filter terminal 2 3 28 29 BBE1a BBE2a BBE2b BBE1b Ach BBE Filter1 (Process) Ach BBE Filter2 (Lo Contour) Bch BBE Filter2 (Lo Contour) Bch BBE Filter1 (Process) 6 25 TONE-Ha TONE-Hb Treble (tone control) filter terminal -6- V+/2 FB 6k 10 4, 8 23,27pin 10pin FB V+/2 2,3 28,29pin FB FB V+/2 20k 6, 25pin V+/2 PRELIMINARY NJW1164 !TERMINAL DESCRIPTION No. SYMBOL FUNCTION 7 24 TONE-La TONE-Lb Bass (tone control) filter terminal 9 AGC Capacitor connection terminal for AGC attack and recovery time setting 11 12 CVB CVA Pop Noise Reduction for Volume & Balance EQUIVALENT CIRCUIT 12k VOLTAGE 7, 24pin V+/2 12k FB 9pin 400 - 4k 400 11,12pin 8k - 5V 13 SDA 13pin 4k 2 I C data terminal - 8k 5V 14 SCL 2 I C clock terminal 14pin 4k - 8k -7- NJW1164 PRELIMINARY !TERMINAL DESCRIPTION No. SYMBOL FUNCTION 5 26 TONE INa TONE INb Ach Input from the Other Accessories Bch Input from the Other Accessories EQUIVALENT CIRCUIT 5,26pin 24k VOLTAGE V+/2 212k 21 Vref V+/2 Reference voltage terminal 21pin 212k 5V 17 18 AUX0 AUX1 0/5V Auxiliary 2 values voltage output terminal 50 20 19 CTH CTL Pop Noise reduction for Bass Control Pop Noise reduction for Treble Control 22 SR-FIL Surround filter terminal 15 16 V+ GND Ground terminal Supply voltage terminal -8- V+ 19pin FB 17, 18pin 36k 2k - - 22pin V+/2 - PRELIMINARY NJW1164 APPLICATION CIRCUIT 4.7 4.7 1 INa 3.3n 2 33n 4.7 4.7 INb 30 BBE1a BBE1b 29 3.3n 3 BBE2a BBE2b 28 33n 4 BBEOUTa BBEOUTb 27 5 TONEINa TONEINb 26 4.7 4.7 4.7n 6 TONE-Ha TONE-Hb 25 4.7n 100n 7 TONE-La TONE-Lb 24 100n 8 OUTa OUTb 23 1 9 AGC SR-FIL 22 100n 100n 10 SS-FIL VREF 21 4.7 4.7 11 CVB CTH 20 4.7 4.7 12 CVA CTL 19 4.7 13 SDA AUX0 18 14 SCL AUX1 17 15 GND Vcc 16 4.7 4.7 22 (NOTE) 2 1. Separate the I C bus line from the following terminals for avoiding digital noise problem. Pin No. Symbol Pin No. Symbol Pin No. Symbol Pin No. Symbol Pin No. 2 BBE1a 6 TONE-Ha 10 SS FIL 24 TONE-Lb 28 3 BBE2a 7 TONE-La 22 SR FIL 25 TONE-Hb 29 Symbol BBE2b BBE1b 2. The constant of capacitors connected to the terminals No.2, 3, 28 and 29 are designated by BBE Sound Inc. Do not change the constant of these capacitors without the approval of BBE Sound Inc. -9- NJW1164 PRELIMINARY APPLICATION NOTE 1. AGC (Auto Gain Control) Circuit AGC circuit adjusts the input signal level with Boost/Attenuate circuit. AGC boost the low input signal level and attenuate high input signal level automatically. 2 The AGC flat levels (150mV, 300mV, 400mV and 540mV) are selectable via I C bus. (Refer to the following figure.) AGC Control V+=9V, Vin(Ach+Bch), f=1kHz, Vo(Ach)OUTPUT Rg=600, Ta=25oC 540mV Output Voltage [Vrms] 1 400mV 0.1 AGC ON 300mV 150mV 0.01 0.001 0.001 AGC OFF 0.01 0.1 1 Input Voltage [Vrms] Attack-Recovery Rb=8k Ra=4k 9pin Ir=0.5A 11pin 12pin Cb Ca Smoothing circuit of Attenuate Smoothing circuit of Boost Attack and recovery time in the attenuation processing depends on external part Ca, and it in the boost processing depends on external part Cb. They become longer as the capacity bigger and become shorter as it gets smaller. (Recommendation value: Ca=1F, Cb=4.7F) Reducing the capacity of Ca may cause the distortion. As for Cb, since it serves as the click noise prevention, reducing the capacity may cause the click noise upon volume changing. - 10 - PRELIMINARY NJW1164 2. Tone Control a) Bass: Setting the Cut-off frequency Bass Filter 12k fC = 12k 8pin 23pin M 2 x C x12k M changes by gain setting of Tone. M 2.65 M 3.45 M 8.10 C (15dB) (10dB) (5dB) b) Treble: Setting the Cut-off frequency Treble Filter fC = N 2 x C x10k N changes by gain setting of Tone. 10k C 3. 7pin 24pin N 0.76 N 0.58 N 0.25 (15dB) (10dB) (5dB) BBE, Surround mode and "OUT" switch settings The click noise may be generated by changing the BBE, Surround mode setting and "OUT" switch. Provide the external circuit for avoiding the click noise on above condition. 4. External parts for BBE circuits The constant of capacitors connected to the terminals No.2, 3, 28 and 29 are designated by BBE Sound Inc. Do not change the constant of these capacitors without the approval of BBE Sound Inc. 5. AUX1, AUX0 Terminal AUX1/0 are enable to control external logic circuit is Source current : 1mA typ. (Ta=25uC) Sink current : 0.5mA typ. (Ta=25uC) 6. Capacitor for Reference Voltage (21pin) 22F should be recommended for ripple filter connected to Vref terminal (21pin). Reducing this capacity may cause to reduce the maximum attenuation level and to increase the output noise. - 11 - NJW1164 PRELIMINARY 2 DEFINITION OF I C REGISTER 2 I C BUS FORMAT MSB S LSB Slave Address 1bit 8bit MSB LSB A Select Address 1bit 8bit MSB A 1bit LSB Data A P 8bit 1bit 1bit S: Starting Term A: Acknowledge Bit P: Ending Term SLAVE ADDRESS MSB LSB 1 0 0 0 0 1 0 R/W R/W=0: Receive Only R/W=1: No Output Data CONTROL REGISTER TABLE The select address sets each function (Volume, Balance, AGC, Surround, Tone Control, BBE, AUX). The auto increment function cycles the select address as follows. 00H01H02H03H04H05H00H Select Address BIT D7 D6 D5 D4 00H D3 D2 D1 D0 AGC SUR VOL 01H CHS 02H BCB BASS BCSB SUB-BASS 03H BCT TREB BCST SUB-TREB 04H 05H BAL BBE (Lo Contour) OUT Don't care Don't care BBE (Process) SUR0 AGC1 AGC0 AUX1 AUX0 CONTROL REGISTER DEFAULT VALUE Control register default value is all "0". Select Address - 12 - BIT D7 D6 D5 D4 D3 D2 D1 D0 00H 0 0 0 0 0 0 0 0 01H 0 0 0 0 0 0 0 0 02H 0 0 0 0 0 0 0 0 03H 0 0 0 0 0 0 0 0 04H 0 0 0 0 0 0 0 0 05H 0 0 0 0 0 0 0 0 PRELIMINARY NJW1164 !INSTRUCTION CODE a) MASTER VOLUME SETTING Select Address BIT D7 D6 D4 D5 00H D3 D2 D1 D0 VOL The volume control for both Ach and Bch (0.33dB/step). The volume is consisted of volume1 and volume2 and the level is divided into half to each volume1 and volume2. b) BALANCE, AGC AND SURROUND SETTING BIT Select Address D7 01H CHS D6 D4 D5 D3 D2 BAL D1 D0 AGC SUR *CHS: Channel select for balance control "0": Ach "Bch is attenuated" "1": Bch "Ach is attenuated" *BAL: Balance control for both Ach and Bch (1dB/Step) The balance is consisted of volume1 and volume2 and the level is divided into half to each volume1 and volume2. *AGC: AGC switch "0": AGC OFF "1": AGC ON *SUR: Surround mode switch "0": Surround OFF "1": Surround ON NOTE) The click noise may be generated by changing the Surround mode setting. Provide the external circuit for avoiding the click noise on above condition. c) TONE CONTROL BASS SETTING BIT Select Address D7 02H BCB D6 D4 D5 BASS D3 D2 BCSB D1 D0 SUB-BASS *BCB: Boost cut select for Bass control "0": Cut "1": Boost *BASS: BASS control Cut Level : -15dB to 0dB(1dB/Step) Boost Level : 0dB to +15dB(1dB/Step) *BCSB: Boost cut select for SUB-BASS control "0": Cut "1": Boost *SUB-BASS: SUB- BASS control (1dB/Step) Sub-Cut Level : -3dB to 0dB(1dB/Step) Sub-Boost Level : 0dB to +3dB(1dB/Step) - 13 - NJW1164 PRELIMINARY d) TONE CONTROL TREBLE SETTING BIT Select Address D7 03H BCT D6 D4 D5 D3 TREB D2 BCST D1 D0 SUB-TREB *BCT: Boost cut select for Treble control "0": Cut "1": Boost *TREB: Treble control (1dB/step) Cut Level : -15dB to 0dB(1dB/Step) Boost Level : 0dB to +15dB(1dB/Step) *BCST: Boost cut select for Sub-Treble control "0": Cut "1": Boost *SUB-TREB: Sub-Treble control (1dB/step) Sub-Cut Level : -3dB to 0dB(1dB/Step) Sub-Boost Level : 0dB to +3dB(1dB/Step) e) BBE Boost Level Setting Select Address BIT D7 04H D6 D5 D4 D3 BBE (Lo Contour) * BBE Lo Contour * BBE Process D2 D1 D0 BBE (Process) : 0dB to 15dB(1dB/step) : 0dB to 15dB (1dB/step) When all bits are "0"(=00H), BBE becomes off NOTE) The click noise may be generated by changing the BBE setting. Provide the external circuit for avoiding the click noise on above condition. f) OUTPUT AND AUXILIARY SETTING BIT Select Address D7 D6 D5 D4 D3 D2 D1 D0 05H OUT Don't Care Don't Care SUR0 AGC1 AGC0 AUX1 AUX0 *OUT: ON/OFF Switch for OUTPUT "0" : OFF "1" : ON NOTE) The click noise may be generated by changing the "OUT" switch. Provide the external circuit for avoiding the click noise on above condition. *Surround Setting Surround Function Surround OFF Surround Effect1 Surround Effect2 Simulated Stereo SUR0(05H:D4) 0 0 1 1 SUR(01H:D0), Remarks 0 Input through 1 Surround Effect Small ( 8.0dB typ. ) 1 Surround Effect Large (12.7dB typ. ) 0 For monaural signal input only NOTE) The click noise may be generated by changing the Surround mode setting. Provide the external circuit for avoiding the click noise on above condition. - 14 - PRELIMINARY *AGC Level Setting AGC Level AGC1(D3) 150mVrms 0 300mVrms 0 400mVrms 1 540mVrms 1 *AUX1/AUX0: Auxiliary port High/Low "0": Logic output "Low" "1": Logic output "High" NJW1164 AGC0(D2) 0 1 0 1 - 15 - NJW1164 PRELIMINARY !MASTER VOLUME (Select Address: 00H) VOL Gain (dB) HEX D7 D6 D5 D4 D3 D2 D1 D0 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 -23 -24 -25 -26 -27 -28 -29 -30 -31 -32 -33 -34 -35 -36 -37 -38 -39 -40 -41 -42 FF FC F9 F6 F3 F0 ED EA E7 E4 E1 DE DB D8 D5 D2 CF CC C9 C6 C3 C0 BD BA B7 B4 B1 AE AB A8 A5 A2 9F 9C 99 96 93 90 8D 8A 87 84 81 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 - 16 - PRELIMINARY NJW1164 !MASTER VOLUME (Select Address: 00H) VOL Gain (dB) HEX D7 D6 D5 D4 D3 D2 D1 D0 -43 -44 -45 -46 -47 -48 -49 -50 -51 -52 -53 -54 -55 -56 -57 -58 -59 -60 -61 -62 -63 -64 -65 -66 -67 -68 -69 -70 -71 -72 -73 -74 -75 -76 -77 -78 -79 -80 -81 -82 -83 -84 Mute 7E 7B 78 75 72 6F 6C 69 66 63 60 5D 5A 57 54 51 4E 4B 48 45 42 3F 3C 39 36 33 30 2D 2A 27 24 21 1E 1B 18 15 12 0F 0C 09 06 03 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 1 1 0 0 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 - 17 - NJW1164 PRELIMINARY !BALANCE (Select Address: 01H) Channel Select (CHS) D7 Ach (Bch is attenuated) 0 Bch (Ach is attenuated) 1 BAL - 18 - Gain (dB) D6 D5 D4 D3 D2 0 0 0 0 0 0 -1 0 0 0 0 1 -2 0 0 0 1 0 -3 0 0 0 1 1 -4 0 0 1 0 0 -5 0 0 1 0 1 -6 0 0 1 1 0 -7 0 0 1 1 1 -8 0 1 0 0 0 -9 0 1 0 0 1 -10 0 1 0 1 0 -11 0 1 0 1 1 -12 0 1 1 0 0 -13 0 1 1 0 1 -14 0 1 1 1 0 -15 0 1 1 1 1 -16 1 0 0 0 0 -17 1 0 0 0 1 -18 1 0 0 1 0 -19 1 0 0 1 1 -20 1 0 1 0 0 -21 1 0 1 0 1 -22 1 0 1 1 0 -23 1 0 1 1 1 -24 1 1 0 0 0 -25 1 1 0 0 1 -26 1 1 0 1 0 -27 1 1 0 1 1 -28 1 1 1 0 0 -29 1 1 1 0 1 -30 1 1 1 1 0 Mute 1 1 1 1 1 PRELIMINARY NJW1164 !TONE CONTROL BASS (Select Address: 02H) Bass Cut or Boost BCB D7 Cut 0 Boost 1 BASS Cut Gain (dB) Boost Gain (dB) D6 D5 D4 D3 -15 15 1 1 1 1 -14 14 1 1 1 0 -13 13 1 1 0 1 -12 12 1 1 0 0 -11 11 1 0 1 1 -10 10 1 0 1 0 -9 9 1 0 0 1 -8 8 1 0 0 0 -7 7 0 1 1 1 -6 6 0 1 1 0 -5 5 0 1 0 1 -4 4 0 1 0 0 -3 3 0 0 1 1 -2 2 0 0 1 0 -1 1 0 0 0 1 0 0 0 0 0 0 !TONE CONTROL SUB-BASS (Select Address: 02H) Sub-Bass Cut or Boost BCSB D2 Cut 0 Boost 1 SUB-BASS Cut Gain (dB) Boost Gain (dB) D1 D0 -3 3 1 1 -2 2 1 0 -1 1 0 1 0 0 0 0 - 19 - NJW1164 PRELIMINARY !TONE CONTROL TREBLE (Select Address: 03H) Treble Cut or Boost BCT D7 Cut 0 Boost 1 TREB Cut Gain (dB) Boost Gain (dB) D6 D5 D4 D3 -15 15 1 1 1 1 -14 14 1 1 1 0 -13 -12 13 12 1 1 1 1 0 0 1 0 -11 11 1 0 1 1 -10 10 1 0 1 0 -9 9 1 0 0 1 -8 8 1 0 0 0 -7 7 0 1 1 1 -6 6 0 1 1 0 -5 5 0 1 0 1 -4 4 0 1 0 0 -3 3 0 0 1 1 -2 2 0 0 1 0 -1 1 0 0 0 1 0 0 0 0 0 0 !TONE CONTROL SUB-TREBLE (Select Address : 03H) Sub-Treble Cut or Boost BCST D2 Cut 0 Boost 1 SUB-TREB Cut Gain (dB) Boost Gain (dB) D1 D1 -3 3 1 1 -2 2 1 0 -1 1 0 1 0 0 0 0 - 20 - PRELIMINARY NJW1164 !BBE (Lo Contour) / (Process) Gain Code (Select Address: 04H) Lo Contour Process Gain (dB) D7 D6 D5 D4 D3 D2 D1 D0 15 1 1 1 1 1 1 1 1 14 1 1 1 0 1 1 1 0 13 1 1 0 1 1 1 0 1 12 1 1 0 0 1 1 0 0 11 1 0 1 1 1 0 1 1 10 1 0 1 0 1 0 1 0 9 1 0 0 1 1 0 0 1 8 1 0 0 0 1 0 0 0 7 0 1 1 1 0 1 1 1 6 0 1 1 0 0 1 1 0 5 0 1 0 1 0 1 0 1 4 0 1 0 0 0 1 0 0 3 0 0 1 1 0 0 1 1 2 0 0 1 0 0 0 1 0 1 0 0 0 1 0 0 0 1 0 0 0 0 0 0 0 0 0 - 21 - NJW1164 PRELIMINARY !TYPICAL CHARACTERISTICS Supply Current vs Supply Voltage Supply Current vs Temparature Ta=25oC V+=9V 15 Supply Current [mA] Supply Current [mA] 16 10 5 0 0 5 10 14 12 10 8 15 0 V+=9V, Vin(Ach)=1Vrms,f=1kHz, OUTPUT,Rg=600 0 -20 -40 -40 o 75,25,-20 C Gain [dB] Gain [dB] V+=9V, Vin=1Vrms, f=1kHz, Rg=600 -20 -60 Vo(Bch) -60 75, 25, -20oC Vo(Ach) 75, 25, -20oC -80 -80 -100 100 Gain vs Balance Control Gain vs Volume Control 0 50 Temparature [oC] Supply Voltage [V] 0 -10 -20 -30 -40 -50 -60 -70 -80 MUTE -100 MUTE -30 -30 Volume Control [dB] 00 10 -10 20 -20 30-30 Balance Control [dB] Output Noise vs Temperature Output Noise vs Volume Control V+=9V, OUTPUT,BW=400-30kHz V+=9V, Rg=600, BW=400Hz-30kHz Rg=600, Ta=25oC -60 -20 -20 -10 -10 -40 Output Noise [dBV] -70 Gain [dB] -80 -90 -100 -60 Vol=0dB -80 -100 -110 Vol=MUTE -120 0 -10 -20 -30 -40 -50 -60 -70 -80 MUTE Volume Control [dB] - 22 - -120 0 50 Temparature [oC] 100 MUT PRELIMINARY NJW1164 !TYPICAL CHARACTERISTICS THD+N vs Input Voltage THD+N vs Input Voltage V+=9V, Vin(Ach), f=1kHz, Vo(Ach)OUTPUT V+=9V, Vin(Ach), f=1kHz, Vo(Ach)OUTPUT Rg=600, BW=400Hz-30kHz, Vol=-20dB 100 Rg=600, BW=400Hz-30kHz, Ta=25 oC 100 10 -30dB THD+N [ % ] THD+N [ % ] 10 1 0.1 1 0.1 -20dB -10dB 0.01 0.01 75oC 0dB 0.1 0.01 0.01 1 Input Voltage [Vrms] THD+N vs Output Voltage THD+N vs Output Voltage 100 10 10 -30dB THD+N [ % ] THD+N [ % ] 1 V+=9V, Vin(Ach), f=1kHz, Vo(Ach)OUTPUT Rg=600, BW=400Hz-30kHz, Vol=0dB BW=400Hz-30kHz, Rg=600, Ta=25oC 100 1 0.1 -20oC 1 25oC 0.1 -20dB 0.01 0.01 -10dB 0.1 75 oC 0dB 0.01 0.01 1 Output Voltage [Vrms] V+=9V, Vin=2Vrms, f=1kHz, Vo=OUTPUT Vo(Ach)OUTPUT, Rg=600, Ta=25oC 120 100 Channel Separation [dB] 100 80 60 40 20 1000 Frequency [Hz] 1 Channel Separation vs Frequency V+=9V, Vin(Ach)=1Vrms, Vol=MUTE 100 0.1 Output Voltage [Vrms] MUTE Level vs Frequency MUTE Level [dB] 0.1 Input Voltage [Vrms] V+=9V, Vin(Ach), f=1kHz, Vo(Ach)OUTPUT 0 25oC -20oC 10 4 Rg=600, Vol=0dB, Ta=25oC 80 60 Vin(Ach)-Vo(Bch) Vin(Bch)-Vo(Ach) 40 20 0 100 1000 10 4 Freqency [Hz] - 23 - NJW1164 PRELIMINARY !TYPICAL CHARACTERISTICS Gain vs Frequency (TONE) Gain vs Frequency (TONE) V+=9V, Vin(Ach)=0.1Vrms,Gv:3dB steps V+=9V, Vin(Ach)=0.1Vrms,Gv= +-15dB Vo(Ach), Rg=600, Ta=25oC 20 C(7,24pin) = 47nF, 100nF, 220nF, 470nF 100nF 10 Gain [dB] 10 Gain [dB] Vo(Ach), Rg=600, Ta=25oC 20 0 470nF 0 220nF 47nF -10 -10 -20 100 1000 10 -20 4 100 10 AGC Control Gain vs Frequency (TONE) V+=9V, Vin(Ach)=0.1Vrms,Gv= +-15dB V+=9V, Vin(Ach+Bch), f=1kHz, Vo(Ach)OUTPUT Vo(Ach), Rg=600, Ta=25oC Rg=600, Ta=25oC C(6,25pin) = 1nF, 2.2nF, 4.7nF, 10nF 540mV Output Voltage [Vrms] 1 Gain [dB] 10 2.2nF 10nF 0 1nF -10 4.7nF -20 100 1000 10 400mV 300mV 0.1 150mV 0.01 OFF 0.001 0.001 4 0.01 0.1 1 Input Voltage [Vrms] Frequency [Hz] AGC Attack Time (C:9pin=1 F) AGC Recovery Time (C:9pin=1 F) V+=9V, Vin(Ach+Bch)=1Vrms, f=10kHz,Vo(Ach)OUTPUT AGC level=0.15V,Rg=600,Ta=25oC 2 AGC level=0.15V,Rg=600,Ta=25oC 0.2 1 Output Voltage [V] Output Voltage [V] V+=9V, Vin(Ach+Bch)=1Vrms,f=20kHz,Vo(Ach)OUTPUT 0 -1 -2 0 2 4 6 Time [ms] - 24 - 4 Frequency [Hz] Frequency [Hz] 20 1000 8 10 0.1 0 -0.1 -0.2 0 100 200 300 Time [ms] 400 500 PRELIMINARY NJW1164 !TYPICAL CHARACTERISTICS AGC Recovery Time (C:9pin=2.2 F) V+=9V, Vin(Ach+Bch)=1 to 0.05Vrms, f=10kHz, AGC level=0.15V,Rg=600,Ta=25oC 2 Vo(Ach)OUTPUT,AGC level=0.15V,Rg=600,Ta=25oC 0.2 1 Output Voltage [V] Output Voltage [V] AGC Attack Time (C:9pin=2.2 F) V+=9V, Vin(Ach+Bch)=1Vrms,f=20kHz,Vo(Ach)OUTPUT 0 -1 -2 0 2 4 6 8 0.1 0 -0.1 -0.2 10 0 100 Time [ms] 300 400 500 Time [ms] AGC Attack Time (C:9pin=0.47 F) AGC Recovery Time (C:9pin=0.47 F) V+=9V, Vin(Ach+Bch)=1Vrms,f=20kHz,Vo(Ach)OUTPUT V+=9V, Vin(Ach+Bch)=1 to 0.05Vrms, f=10kHz, AGC level=0.15V,Rg=600,Ta=25oC 2 Vo(Ach)OUTPUT,AGC level=0.15V,Rg=600,Ta=25oC 0.2 1 Output Voltage [V] Output Voltage [V] 200 0 -1 -2 0.1 0 -0.1 -0.2 0 2 4 6 Time [ms] 8 10 0 100 200 300 400 500 Time [ms] - 25 - NJW1164 PRELIMINARY !TYPICAL CHARACTERISTICS Gain vs Frequency (eala&Simulated) Phase vs Frequency (Simulated) V+=9V, Vin=0.1Vrms,OUTPUT, Rg=600, V+=9V, Vin(A+Bch)=0.1Vrms, Rg=600, 20 Ta=25oC 200 eala AIN-AOUT Ta=25oC BchOUT 150 0 Phase [deg] Gain [dB] 10 Simulated (A+B)IN-AOUT eala AIN-BOUT -10 100 50 AchOUT 0 -50 -20 100 1000 10 -100 4 100 Frequency [Hz] V+=9V, Vin(Ach)=0.1Vrms, Vo(Ach) OUTPUT,Rg=600, Ta=25oC 200 100 Phase [deg] Gain [dB] Gv:3dB steps, Rg=600, Ta=25oC +15 15 10 5 +3 0 BBE OFF +15 -100 0 BBE OFF 100 1000 Frequency [Hz] - 26 - 4 Phase vs Frequency (BBE) Gain vs Frequency (BBE) -5 10 Frequency [Hz] V+=9V, Vin(Ach)=0.1Vrms,Gv=3dB steps 20 1000 10 +3 4 -200 100 1000 Frequency [Hz] 10 4 PRELIMINARY NJW1164 NOTE The NJW1164 is manufactured by New Japan Radio Co., Ltd. under license from BBE Sound Inc. A license from BBE Sound Inc. is required before the NJW1164 can be purchased from New Japan Radio Co., Ltd. BBE Sound, Inc. 5381 Production Drive Huntington Beach, CA 92649 Tel:(714) 897-6766 Fax:(714) 896-0736 2 Purchase of I C components of New Japan Radio Co., Ltd or one of its sublicensed Associated Companies 2 2 conveys a license under the Philips I C Patent Rights to use these components in an I C system, provided that 2 the system conforms to the I C Standard Specification as defined by Philips. [CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights. - 27 - This datasheet has been downloaded from: www.EEworld.com.cn Free Download Daily Updated Database 100% Free Datasheet Search Site 100% Free IC Replacement Search Site Convenient Electronic Dictionary Fast Search System www.EEworld.com.cn All Datasheets Cannot Be Modified Without Permission Copyright (c) Each Manufacturing Company Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: NJR: NJW1164M