SC70-5 SOT23-5
MiniSO8 DFN8 2x2
Features
• Ultra low current consumption: 250 nA typ./op.
• Propagation delay: 2 µs typ.
• Rail-to-rail inputs
• Open-drain outputs
• Supply operation from 0.9 V to 5.5 V
• Wide temperature range: -40 to +125 °C
• ESD tolerance: 8 kV HBM
• Single version available in SC70-5 and SOT23-5 package
• Dual version available in MiniSO8 and DFN8 2x2 mm package
Applications
• Portable systems
• Signal conditioning
• Medical
Description
The open-drain series of nanopower comparator integrates a single version TS880
and a dual version TS883. They feature an ultra low supply current of 250 nA typical
per operator with rail-to-rail input capability and open-drain output. The performance
of these comparators allows them to be used in a wide range of portable
applications. The TS880 and TS883 minimize battery supply leakage and therefore
enhance battery lifetime.
Operating from 0.9 to 5.5V supply voltage, these comparators can be used over a
wide temperature range (-40 to +125 °C) keeping the current consumption at an ultra
low level.
Product status link
TS880, TS883
Related products
TS881
See the datasheet for
push-pull output version
TS882
TS884
Rail-to-rail 0.9 V open-drain output, nanopower comparators
TS880, TS883
Datasheet
DS12948 - Rev 1 - April 2019
For further information contact your local STMicroelectronics sales office.
www.st.com
1Pin description
Figure 1. Pin connection TS880 (top view)
OUT
VCC-
IN+
VCC+
IN-
1
2
3
5
4
OUT
IN+
VCC-
IN-
VCC+
SC70-5
SOT23-5
Figure 2. Pin connection TS883 (top view)
MiniSO8/DFN8
TS880, TS883
Pin description
DS12948 - Rev 1 page 2/31
2Absolute maximum ratings and operating conditions
Table 1. Absolute maximum ratings
Symbol Parameter Value Unit
VCC Supply voltage(1) 6 V
VID Differential input voltage(2) ± VCC V
VIN Input voltage range (VCC-) - 0.3 to (VCC+) + 0.3 V
IIN Input current(3) ±10 mA
VOUT Output voltage 6 V
RTHJA
Thermal resistance junction to ambient SC70-5 205
°C/W
Thermal resistance junction to ambient
SOT23-5 250
Thermal resistance junction to ambient
MiniSO8 190
Thermal resistance junction to ambient DFN8
2x2 mm 57
TSTG Storage temperature -65 to +150 °C
TJJunction temperature 150 °C
TLEAD Lead temperature (soldering 10 s) 260 °C
ESD
Human body model (HBM)(4) 8000
V
Charged device model (CDM)(5) 1500
1. All voltage values, except differential voltages, are referenced to VCC-. VCC is defined as the difference between VCC+ and
VCC-.
2. The magnitude of input and output voltages must never exceed the supply rail ±0.3 V.
3. Input current must be limited by a serial resistor with inputs when the input voltage is beyond supply voltage.
4. According to JEDEC standard JESD22-A114F.
5. According to ANSI/ESD STM5.3.1.
Table 2. Operating conditions
Symbol Parameter Value Unit
Toper Operating temperature range -40 to +125 °C
VCC Supply voltage 0.9 to 5.5 V
VICM
Common mode input voltage range
0.9 < Vcc < 1.1 V (1)
(VCC-) - 0.2 to (VCC-) + 0.2
and
(VCC+) - 0.2 to (VCC+) + 0.2 V
Common mode input voltage range
1.1 ≤ Vcc < 5.5 V (VCC-) - 0.2 to (VCC+) + 0.2
VOUT Output voltage 0 to 5.5 V
1. See Figure 13. Input offset voltage vs. input common mode voltage, Vcc=0.9 V, Figure 14. Input hysteresis voltage vs.
input common mode voltage, Vcc=0.9 V, Figure 27. Propagation delay TPLH vs. input common mode voltage, Vcc=0.9 V
and Figure 28. Propagation delay TPHL vs. input common mode voltage, Vcc=0.9 V.
TS880, TS883
Absolute maximum ratings and operating conditions
DS12948 - Rev 1 page 3/31
3Electrical characteristics
Table 3. Electrical characteristics VCC = +0.9 V, Tamb = 25 °C, VICM = 0 V (unless otherwise specified).
Symbol Parameter Test conditions Min. Typ. Max. Unit
VIO Input offset voltage (1)
Tamb = + 25 °C -10 1 10
mV
-40 °C < Tamb < +85 °C -12 12
ΔVIO Input offset voltage drift -40 °C < Tamb < +85 °C 3 µV/°C
VHYST Input hysteresis voltage
(2)
Tamb = +25 °C 2.6
mV
-40 °C < Tamb < +85 °C 1 4.2
IIO Input offset current (3)
Tamb = + 25 °C 1 10
pA
-40 °C < Tamb< + 85 °C 100
IIB Input bias current (3)
Tamb = + 25 °C 5 10
pA
- 40 °C < Tamb < + 85 °C 100
ICC Supply current per
operator
Output low, VID = - 0.1 V 300 480
nA
- 40 °C < Tamb < + 85 °C 500
Output high,VID = + 0.1 V 250 410
-40 °C < Tamb < + 85 °C 440
ISink Output sink current VOUT = VCC+, VID = - 0.1 V 1.2 mA
IOH High level output current
VOUT = VCC+, VID = 0.1 V 17 30 pA
-40 °C < Tamb < + 85 °C 15 nA
VOL Output voltage low
Isink = 50 µA, VID = - 0.1 V 10 50
mV
-40 °C < Tamb < + 85 °C 70
TPLH
Propagation delay (4)
(low to high)
f = 1 kHz, CL = 10 pF, overdrive = 10 mV
VPU = VCC+
µs
RPU = 10 kΩ, Tamb = +25 °C 7 10
RPU = 10 kΩ, 40 °C < Tamb < +85 °C 12
RPU = 1 MΩ, Tamb = +25 °C 20 22
RPU = 1 MΩ, -40 °C < Tamb < +85 °C 24
f = 1 kHz, CL = 10 pF, overdrive = 100 mV
VPU = VCC+
RPU = 10 kΩ, Tamb = +25 °C 2.5 4
RPU = 10 kΩ, 40 °C < Tamb < +85 °C 4.5
RPU = 1 MΩ, Tamb = +25 °C 18 20
RPU = 1 MΩ, -40 °C < Tamb < +85 °C 21
TS880, TS883
Electrical characteristics
DS12948 - Rev 1 page 4/31
Symbol Parameter Test conditions Min. Typ. Max. Unit
TPHL
Propagation delay (5)
(high to low)
f = 1 kHz, CL = 10 pF, overdrive = 10 mV
VPU = VCC+
µs
RPU = 10 kΩ, Tamb = +25 °C 6 9
RPU = 10 kΩ, 40 °C < Tamb < +85 °C 10
RPU = 1 MΩ, Tamb = +25 °C 7 9
RPU = 1 MΩ, -40 °C < Tamb < +85 °C 10
f = 1 kHz, CL = 10 pF, overdrive = 100 mV
VPU = VCC+
RPU = 10 kΩ, Tamb = +25 °C 2 3.5
RPU = 10 kΩ, 40 °C < Tamb < +85 °C 4
RPU = 1 MΩ, Tamb = +25 °C 2 4
RPU = 1 MΩ, -40 °C < Tamb < +85 °C 5
TRRise time (10% to 90%) CL = 10 pF, RPU = 10 kΩ, overdrive = 100 mV 500 ns
TFFall time (90% to 10%) CL = 10 pF, RPU = 10 kΩ, overdrive = 100 mV 600 ns
TON Power-up time 0.9 1.3 ms
1. The offset is defined as the average value of positive and negative trip points (input voltage differences requested to change
the output state in each direction).
2. The hysteresis is a built-in feature. It is defined as the voltage difference between the trip points.
3. Maximum values include unavoidable inaccuracies of the industrial tests.
4. TPLH is measured when the output signal crosses a voltage level at 50% of VCC with the following conditions: inverting input
voltage (IN-) = VICM and non-inverting input voltage (IN+) moving from VICM - 100 mV to VICM + overdrive.
5. TPHL is measured when the output signal crosses a voltage level at 50% of VCC with the following conditions: inverting input
voltage (IN-) = VICM and non-inverting input voltage (IN+) moving from VICM + 100 mV to VICM - overdrive
Note: All values over the temperature range are guaranteed through correlation and simulation. No production test is
performed at the temperature range limits.
TS880, TS883
Electrical characteristics
DS12948 - Rev 1 page 5/31
Table 4. Electrical characteristics VCC = +1.2 V, Tamb = 25 °C, VICM = VCC/2 (unless otherwise specified).
Symbol Parameter Test conditions Min. Typ. Max. Unit
VIO Input offset voltage(1)
Tamb = + 25 °C -5 1 5
mV
-40 °C < Tamb < +125 °C -6 6
ΔVIO Input offset voltage drift -40 °C < Tamb < +125 °C 3 µV/°C
VHYST Input hysteresis voltage
(2)
Tamb = +25 °C 2.5
mV
-40 °C < Tamb < +125 °C 1.6 4.2
IIO Input offset current (3)
Tamb = + 25 °C 2 10
pA
-40 °C < Tamb< + 125 °C 100
IIB Input bias current (3)
Tamb = + 25 °C 1 10
pA
- 40 °C < Tamb < + 125 °C 100
ICC Supply current per
operator
Output low, VID = - 0.1 V 320 490
nA
- 40 °C < Tamb < + 125 °C 510
Output high,VID = + 0.1 V 240 360
-40 °C < Tamb < + 125 °C 390
ISink Output sink current VOUT = VCC+, VID = - 0.1 V 3.6 mA
IOH High level output current
VOUT = VCC+, VID = 0.1 V 22 36 pA
-40 °C < Tamb < + 125 °C 15 nA
VOL Output voltage low
Isink = 0.2 mA 25 50
mV
-40 °C < Tamb < + 125 °C 70
CMRR Common mode rejection
ratio
0 < VICM < VCC 68
dB
-40 °C < Tamb < + 125 °C 50
TPLH
Propagation delay
(low to high)
f = 1 kHz, CL = 10 pF, overdrive = 10 mV
VPU = VCC+
µs
RPU= 10 kΩ,Tamb= + 25 °C 5 7
RPU= 10 kΩ, 40 °C < Tamb < + 85 °C 8
RPU= 1 MΩ,Tamb= + 25 °C 20 21
RPU= 1 MΩ, -40 °C < Tamb < + 85 °C 22
f = 1 kHz, CL = 10 pF, overdrive = 100 mV
VPU = VCC+
RPU= 10 kΩ,Tamb= + 25 °C 1.9 3
RPU= 10 kΩ, 40 °C < Tamb < + 85 °C 3.5
RPU= 1 MΩ, Tamb = + 25 °C 17 18
RPU= 1 MΩ, -40 °C < Tamb < + 85 °C 19
TS880, TS883
Electrical characteristics
DS12948 - Rev 1 page 6/31
Symbol Parameter Test conditions Min. Typ. Max. Unit
TPHL
Propagation delay (5)
(high to low)
f = 1 kHz, CL = 10 pF, overdrive = 10 mV
VPU = VCC+
µs
RPU= 10 kΩ,Tamb= + 25 °C 5 6
RPU= 10 kΩ, 40 °C < Tamb < + 85 °C 7
RPU= 1 MΩ, Tamb = + 25 °C 5 6
RPU= 1 MΩ, -40 °C < Tamb < + 85 °C 7
f = 1 kHz, CL = 10 pF, overdrive = 100 mV,
VPU = VCC+
RPU= 10 kΩ,Tamb= + 25 °C 1.7 2.5
RPU= 10 kΩ, 40 °C < Tamb < + 85 °C 3
RPU= 1 MΩ, Tamb = + 25 °C 2 3
RPU= 1 MΩ, -40 °C < Tamb < + 85 °C 4
TRRise time (10% to 90%) CL = 10 pF, RPU = 10 kΩ overdrive = 100 mV 800 ns
TFFall time (90% to 10%) CL = 10 pF, RPU = 10 kΩ overdrive = 100 mV 250 ns
TON Power-up time 0.9 1.3 ms
1. The offset is defined as the average value of positive and negative trip points (input voltage differences requested to change
the output state in each direction
2. The hysteresis is a built-in feature. It is defined as the voltage difference between the trip points.
3. Maximum values include unavoidable inaccuracies of the industrial tests.
4. TPLH is measured when the output signal crosses a voltage level at 50% of VCC with the following conditions: inverting input
voltage (IN-) = VICM and non-inverting input voltage (IN+) moving from VICM - 100 mV to VICM + overdrive.
5. TPHL is measured when the output signal crosses a voltage level at 50% of VCC with the following conditions: inverting input
voltage (IN-) = VICM and non-inverting input voltage (IN+) moving from VICM + 100 mV to VICM - overdrive.
Note: All values over the temperature range are guaranteed through correlation and simulation. No production test is
performed at the temperature range limits.
TS880, TS883
Electrical characteristics
DS12948 - Rev 1 page 7/31
Table 5. Electrical characteristics VCC = +2.7 V, Tamb = 25 °C, VICM = VCC/2 (unless otherwise specified).
Symbol Parameter Test conditions Min. Typ. Max. Unit
VIO Input offset voltage
Tamb = + 25 °C -5 1 5
mV
-40 °C < Tamb < +125 °C -6 6
ΔVIO Input offset voltage drift -40 °C < Tamb < +125 °C 3 µV/°C
VHYST Input hysteresis voltage
Tamb = +25 °C 2.7
mV
-40 °C < Tamb < +125 °C 1.6 4.2
IIO Input offset current (3)
Tamb = + 25 °C 1 10
pA
-40 °C < Tamb< + 125 °C 100
IIB Input bias current (3)
Tamb = + 25 °C 5 10
pA
- 40 °C < Tamb < + 125 °C 100
ICC Supply current per
operator
Output low, VID = - 0.1 V 350 520
nA
- 40 °C < Tamb < + 125 °C 540
Output high, VID = + 0.1 V 250 370
-40 °C < Tamb < + 125 °C 400
ISink Output sink current VOUT = VCC+, VID = - 0.1 V 22 mA
IOH High level output current
VOUT = VCC+, VID = 0.1 V 40 60 pA
-40 °C < Tamb < + 125 °C 18 nA
VOL Output voltage low
Isink = 2 mA 140 220
mV
-40 °C < Tamb < + 125 °C 290
CMRR Common mode rejection
ratio
0 < VICM < VCC 74
dB
-40 °C < Tamb < + 125 °C 55
TPLH
Propagation delay
(low to high)
f = 1 kHz, CL = 10 pF, overdrive = 10 mV
VPU = VCC+
µs
RPU= 10 kΩ,Tamb= + 25 °C 5.8 8
RPU= 10 kΩ, 40 °C < Tamb< +85 °C 10
RPU= 1 MΩ, Tamb = + 25 °C 21 23
RPU= 1 MΩ, -40 °C < Tamb< +85 °C 24
f = 1 kHz, CL = 10 pF, overdrive = 100 mV
VPU= VCC+
RPU= 10 kΩ, Tamb= + 25 °C 2 3
RPU= 10 kΩ, 40 °C < Tamb< +85 °C 3.5
RPU= 1 MΩ, Tamb= + 25 °C 18 19
RPU = 1 MΩ, -40 °C < Tamb< +85 °C 20
TS880, TS883
Electrical characteristics
DS12948 - Rev 1 page 8/31
Symbol Parameter Test conditions Min. Typ. Max. Unit
TPHL
Propagation delay
(high to low)
f = 1 kHz, CL = 10 pF, overdrive = 10 mV
VPU = VCC+
µs
RPU= 10 kΩ, Tamb= + 25 °C 5.8 7
RPU= 10 kΩ, 40 °C < Tamb< +85 °C 10
RPU= 1 MΩ, Tamb = + 25 °C 6 7
RPU= 1 MΩ, -40 °C < Tamb< +85 °C 10
f = 1 kHz, CL = 10 pF, overdrive = 100 mV
VPU= VCC+
RPU= 10 kΩ, Tamb= + 25 °C 1.9 3
RPU= 10 kΩ, 40 °C < Tamb< +85 °C 3.5
RPU= 1 MΩ, Tamb= + 25 °C 2 3.5
RPU = 1 MΩ, -40 °C < Tamb< +85 °C 4.5
TRRise time (10% to 90%) CL = 10 pF, RPU = 10 kΩ overdrive = 100 mV 1800 ns
TFFall time (90% to 10%) CL = 10 pF, RPU = 10 kΩ overdrive = 100 mV 170 ns
TON Power-up time 0.9 1.3 ms
1. The offset is defined as the average value of positive and negative trip points (input voltage differences requested to change
the output state in each direction
2. The hysteresis is a built-in feature. It is defined as the voltage difference between the trip points.
3. Maximum values include unavoidable inaccuracies of the industrial tests.
4. TPLH is measured when the output signal crosses a voltage level at 50% of VCC with the following conditions: inverting input
voltage (IN-) = VICM and non-inverting input voltage (IN+) moving from VICM - 100 mV to VICM + overdrive.
5. TPHL is measured when the output signal crosses a voltage level at 50% of VCC with the following conditions: inverting input
voltage (IN-) = VICM and non-inverting input voltage (IN+) moving from VICM + 100 mV to VICM - overdrive.
Note: All values over the temperature range are guaranteed through correlation and simulation. No production test is
performed at the temperature range limits.
TS880, TS883
Electrical characteristics
DS12948 - Rev 1 page 9/31
Table 6. Electrical characteristics VCC = +5 V, Tamb = 25 °C, VICM = VCC/2 (unless otherwise specified).
Symbol Parameter Test conditions Min. Typ. Max. Unit
VIO Input offset voltage
Tamb = + 25 °C -5 1 5
mV
-40 °C < Tamb < +125 °C -6 6
ΔVIO Input offset voltage drift -40 °C < Tamb < +125 °C 3 µV/°C
VHYST Input hysteresis voltage
(2)
Tamb = +25 °C 3.1
mV
-40 °C < Tamb < +125 °C 1.6 4.2
IIO Input offset current (3)
Tamb = + 25 °C 1 10
pA
-40 °C < Tamb< + 125 °C 100
IIB Input bias current (3)
Tamb = + 25 °C 10 20
pA
- 40 °C < Tamb < + 125 °C 100
ICC Supply current per
operator
Output low, VID = - 0.1 V 400 600
nA
- 40 °C < Tamb < + 125 °C 630
Output high, VID = + 0.1 V 290 430
-40 °C < Tamb < + 125 °C 480
ISink Output sink current VOUT = VCC+, VID = - 0.1 V 50 mA
IOH High level output current
VOUT = VCC+, VID = 0.1 V 80 100 pA
-40 °C < Tamb < + 125 °C 20 nA
VOL Output voltage low
Isink = 2 mA 110 180
mV
-40 °C < Tamb < + 125 °C 240
CMRR Common mode rejection
ratio
0 < VICM < VCC 78
dB
-40 °C < Tamb < + 125 °C 55
SVR Supply voltage rejection
ΔVCC=1.2 V to 5 V 80
dB
-40 °C < Tamb < + 125 °C 65
TPLH
Propagation delay (4)
(low to high)
f = 1 kHz, CL = 10 pF, overdrive = 10 mV
VPU = VCC+
µs
RPU= 10 kΩ, Tamb= + 25 °C 7 9
RPU= 10 kΩ, 40 °C < Tamb< +85 °C 13
RPU= 1 MΩ, Tamb = + 25 °C 21 23
RPU= 1 MΩ, -40 °C < Tamb< +85 °C 24
f = 1 kHz, CL = 10 pF, overdrive = 100 mV
VPU= VCC+
RPU= 10 kΩ, Tamb= + 25 °C 3 4
RPU= 10 kΩ, 40 °C < Tamb< +85 °C 5
RPU= 1 MΩ, Tamb= + 25 °C 18 20
RPU = 1 MΩ, -40 °C < Tamb< +85 °C 21
TS880, TS883
Electrical characteristics
DS12948 - Rev 1 page 10/31
Symbol Parameter Test conditions Min. Typ. Max. Unit
TPHL
Propagation delay (5)
(high to low)
f = 1 kHz, CL = 10 pF, overdrive = 10 mV
VPU = VCC+
µs
RPU= 10 kΩ, Tamb= + 25 °C 7.5 9
RPU= 10 kΩ, 40 °C < Tamb< +85 °C 12
RPU= 1 MΩ, Tamb = + 25 °C 9 11
RPU= 1 MΩ, -40 °C < Tamb< +85 °C 13
f = 1 kHz, CL = 10 pF, overdrive = 100 mV
VPU= VCC+
RPU= 10 kΩ, Tamb= + 25 °C 2 3
RPU= 10 kΩ, 40 °C < Tamb< +85 °C 3.5
RPU= 1 MΩ, Tamb= + 25 °C 2 3
RPU = 1 MΩ, -40 °C < Tamb< +85 °C 4
TRRise time (10% to 90%) CL = 10 pF, RPU = 10 kΩ overdrive = 100 mV 3.7 µs
TFFall time (90% to 10%) CL = 10 pF, RPU = 10 kΩ overdrive = 100 mV 190 ns
TON Power-up time 0.9 1.3 ms
1. The offset is defined as the average value of positive and negative trip points (input voltage differences requested to change
the output state in each direction).
2. The hysteresis is a built-in feature. It is defined as the voltage difference between the trip points.
3. Maximum values include unavoidable inaccuracies of the industrial tests
4. TPLH is measured when the output signal crosses a voltage level at 50% of Vcc with the following conditions: inverting input
voltage (IN-) = VICM and non-inverting input voltage (IN+) moving from VICM - 100 mV to VICM + overdrive.
5. TPHL is measured when the output signal crosses a voltage level at 50% of Vcc with the following conditions:inverting input
voltage (IN-) = VICM and non-inverting input voltage (IN+) moving from VICM + 100 mV to VICM - overdrive.
Note: All values over the temperature range are guaranteed through correlation and simulation. No production test is
performed at the temperature range limits.
TS880, TS883
Electrical characteristics
DS12948 - Rev 1 page 11/31
4Typical characteristics and curves
Figure 3. Current consumption vs. supply voltage,
Vicm=Vcc, output low
Supply voltage
Quiescent current per channel
Figure 4. Current consumption vs. supply voltage,
Vicm=Vcc, output high
Supply voltage
Quiescent current per channel (nA)
Figure 5. Current consumption vs. supply voltage,
Vicm=0 V, output low
Supply voltage
Quiescent current per channel (nA)
Figure 6. Current consumption vs. supply voltage,
Vicm=0 V, output high
Quiescent current per channel (nA)
Supply voltage
TS880, TS883
Typical characteristics and curves
DS12948 - Rev 1 page 12/31
Figure 7. Current consumption vs. input common mode
voltage, Vcc=0.9 V, output low
Input common mode voltage
Quiescent current per channel (nA)
Figure 8. Current consumption vs. input common mode
voltage, Vcc=0.9 V, output high
Input common mode voltage (V)
Quiescent current per channel (nA)
Figure 9. Current consumption vs. input common mode
voltage, Vcc=5 V, output low
Input common mode voltage (V)
Quiescent current per channel (nA)
Figure 10. Current consumption vs. input common mode
voltage, Vcc=5 V, output high
Figure 11. Current consumption vs. temperature
Temperature (°C)
Quiescent current per channel (nA)
Figure 12. Current consumption vs. toggle frequency
Toggle frequency (Hz)
Current consumption per channel
TS880, TS883
Typical characteristics and curves
DS12948 - Rev 1 page 13/31
Figure 13. Input offset voltage vs. input common mode
voltage, Vcc=0.9 V
Figure 14. Input hysteresis voltage vs. input common
mode voltage, Vcc=0.9 V
Figure 15. Input offset voltage vs. input common mode
voltage, Vcc=1.2 V
Input common mode voltage (V)
Input offset voltage (V)
Figure 16. Input hysteresis voltage vs. input common
mode voltage, Vcc=1.2 V
Hysteresis voltage (mV)
Input common mode voltage(V)
Figure 17. Input offset voltage vs. input common mode
voltage, Vcc=5 V
Input common mode voltage
Input offset voltage (mV)
Figure 18. Input hysteresis voltage vs. input common
mode voltage, Vcc=5 V
Input common mode voltage (V)
Hysteresis voltage (mV)
TS880, TS883
Typical characteristics and curves
DS12948 - Rev 1 page 14/31
Figure 19. Input offset voltage vs. temperature
Temperature (°C)
Input offset voltage (mV)
Figure 20. Input hysteresis voltage vs. temperature
Temperature (°C)
Hysteresis voltage (mV)
Figure 21. Output voltage drop vs. sink current, Vcc=1.2 V
Output voltage (V)
Output current (A)
Figure 22. Output voltage drop vs. source current,
Vcc=1.2 V
.0
Output current (A)
Output voltage (V)
Figure 23. Output voltage drop vs. sink current, Vcc=2.7 V
Output voltage (V)
Output current (A)
Figure 24. Output voltage drop vs. source current,
Vcc=2.7 V
Output current (A)
Output voltage (V)
TS880, TS883
Typical characteristics and curves
DS12948 - Rev 1 page 15/31
Figure 25. Output voltage drop vs. sink current, Vcc=5 V
Output voltage (V)
Output current (A)
Figure 26. Output voltage drop vs. source current,
Vcc=5 V
Output voltage (V)
Output current (A)
Figure 27. Propagation delay TPLH vs. input common
mode voltage, Vcc=0.9 V
Figure 28. Propagation delay TPHL vs. input common
mode voltage, Vcc=0.9 V
Figure 29. Propagation delay TPLH vs. input common
mode voltage, Vcc=1.2 V
Input common mode voltage (V)
Propagation delay-low to high (µs)
Figure 30. Propagation delay TPHL vs. input common
mode voltage, Vcc=1.2 V
Input common mode voltage (V)
Propagation delay-high to low (µs)
TS880, TS883
Typical characteristics and curves
DS12948 - Rev 1 page 16/31
Figure 31. Propagation delay TPLH vs. input common
mode voltage, Vcc=5 V
Input common mode volatge (V)
Propagation delay-low to high (µs)
Figure 32. Propagation delay TPHL vs. input common
mode voltage, Vcc=5 V
Input common mode voltage (V)
Propagation delay-high to low (µs)
Figure 33. Propagation delay TPLH vs. input signal
overdrive, Vcc=1.2 V
Overdrive voltage (mV)
Propagation delay-low to high (µs)
7
8
Figure 34. Propagation delay TPHL vs. input signal
overdrive, Vcc=1.2 V
Overdrive voltage (mV)
Propagation delay-high to low (µs)
Figure 35. Current consumption Vs. input common mode
voltage, Vcc=0.9 V, output low
Propagation delay-low to high (µs)
1
2
3
4
5
6
7
8
9
10
11
Overdrive voltage (mV)
Figure 36. Current consumption Vs. input common mode
voltage, Vcc=0.9 V, output high
Overdrive voltage (mV)
Propagation delay-high to low (µs)
TS880, TS883
Typical characteristics and curves
DS12948 - Rev 1 page 17/31
Figure 37. Propagation delay TPLH vs. input signal
overdrive, Vcc=5 V
Supply voltage (V)
Propagation delay-low to high (µs)
Figure 38. Propagation delay TPHL vs. input signal
overdrive, Vcc=5 V
Supply voltage (V)
Propagation delay-high to low (µs)
Figure 39. Propagation delay TPLH vs. supply voltage
Time (µs)
Signal amplitude (V)
Figure 40. Propagation delay TPHL vs. supply voltage
Time (µs)
Signal amplitude (V)
TS880, TS883
Typical characteristics and curves
DS12948 - Rev 1 page 18/31
5Package information
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages,
depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product
status are available at: www.st.com. ECOPACK is an ST trademark.
TS880, TS883
Package information
DS12948 - Rev 1 page 19/31
5.1 SC70-5 (or SOT323-5) package information
Figure 41. SC70-5 (or SOT323-5) package outline
SEATING PLANE
GAUGE PLANE
DIMENSIONS IN MM
SIDE VIEW
TOP VIEW
COPLANAR LEADS
Table 7. SC70-5 (or SOT323-5) package mechanical data
Ref.
Dimensions
Millimeters Inches
Min. Typ. Max. Min. Typ. Max.
A 0.80 1.10 0.032 0.043
A1 0.10 0.004
A2 0.80 0.90 1.00 0.032 0.035 0.039
b 0.15 0.30 0.006 0.012
c 0.10 0.22 0.004 0.009
D 1.80 2.00 2.20 0.071 0.079 0.087
E 1.80 2.10 2.40 0.071 0.083 0.094
E1 1.15 1.25 1.35 0.045 0.049 0.053
e 0.65 0.025
e1 1.30 0.051
L 0.26 0.36 0.46 0.010 0.014 0.018
< 0° 8° 0° 8°
TS880, TS883
SC70-5 (or SOT323-5) package information
DS12948 - Rev 1 page 20/31
5.2 SOT23-5 package information
Figure 42. SOT23-5 package outline
SOT23-5
E
e
1
5 x b
e1 D
C
s
E1
L
A
A2
5x
0.10 C
A1
Table 8. SOT23-5 mechanical data
Symbol
Milimeters Inches(1)
Min. Typ. Max. Min. Typ. Max.
A 1.45 0.057
A1 0.00 0.15 0.000 0.006
A2 0.90 1.15 1.30 0.035 0.045 0.051
b 0.30 0.50 0.012 0.020
c 0.08 0.22 0.003 0.009
D 2.90 0.114
E 2.80 0.110
E1 1.60 0.063
e 0.95 0.037
e1 1.90 0.075
L 0.30 0.45 0.60 0.012 0.018 0.024
θ048048
1. Values in inches are converted from mm and rounded to 4 decimal digits.
TS880, TS883
SOT23-5 package information
DS12948 - Rev 1 page 21/31
Figure 43. SOT23-5 recommended footprint
1.10
1
2
3
5
4
0.95
2.30
0.60
TS880, TS883
SOT23-5 package information
DS12948 - Rev 1 page 22/31
5.3 DFN8 2x2 package information
Figure 44. DFN8 2x2 package outline
Table 9. DFN8 2x2 package mechanical data
Ref.
Dimensions
Millimeters Inches
Min. Typ. Max. Min. Typ. Max.
A 0.51 0.55 0.60 0.020 0.022 0.024
A1 0.05 0.002
A3 0.15 0.006
b 0.18 0.25 0.30 0.007 0.010 0.012
D 1.85 2.00 2.15 0.073 0.079 0.085
D2 1.45 1.60 1.70 0.057 0.063 0.067
E 1.85 2.00 2.15 0.073 0.079 0.085
E2 0.75 0.90 1.00 0.030 0.035 0.039
e 0.50 0.020
L 0.225 0.325 0.425 0.009 0.013 0.017
ddd 0.08 0.003
TS880, TS883
DFN8 2x2 package information
DS12948 - Rev 1 page 23/31
Figure 45. DFN8 2x2 recommended footprint
Note: The exposed pad of the DFN8 2x2 can be connected to VCC- or left floating.
TS880, TS883
DFN8 2x2 package information
DS12948 - Rev 1 page 24/31
5.4 MiniSO8 package information
Figure 46. MiniSO8 package outline
Table 10. MiniSO8 mechanical data
Dim. Millimeters Inches
Min. Typ. Max. Min. Typ. Max.
A 1.1 0.043
A1 0 0.15 0 0.006
A2 0.75 0.85 0.95 0.03 0.033 0.037
b 0.22 0.4 0.009 0.016
c 0.08 0.23 0.003 0.009
D 2.8 3 3.2 0.11 0.118 0.126
E 4.65 4.9 5.15 0.183 0.193 0.203
E1 2.8 3 3.1 0.11 0.118 0.122
e 0.65 0.026
L 0.4 0.6 0.8 0.016 0.024 0.031
L1 0.95 0.037
L2 0.25 0.01
k 0° 8° 0° 8°
ccc 0.1 0.004
TS880, TS883
MiniSO8 package information
DS12948 - Rev 1 page 25/31
6Ordering information
Table 11. Order code
Order code Temp. range Package Packing Marking
TS880ICT
-40 to +125 °C
SC70-5
Tape and reel
K5P
TS880ILT SOT23-5 K534
TS883IST MiniSO8
K5Q
TS883IQ2T DFN8 2x2 mm
TS880, TS883
Ordering information
DS12948 - Rev 1 page 26/31
Revision history
Table 12. Document revision history
Date Version Changes
16-Apr-2019 1 Initial release.
TS880, TS883
DS12948 - Rev 1 page 27/31
Contents
1Pin description ....................................................................2
2Absolute maximum ratings and operating conditions ..............................3
3Electrical characteristics...........................................................4
4Typical characteristics and curves ................................................12
5Package information..............................................................19
5.1 Package information ...........................................................20
5.2 SOT23-5 package information...................................................21
5.3 DFN8 2x2 package information ..................................................23
5.4 MiniSO8 package information ...................................................25
6Ordering information .............................................................26
Revision history .......................................................................27
TS880, TS883
Contents
DS12948 - Rev 1 page 28/31
List of tables
Table 1. Absolute maximum ratings .............................................................3
Table 2. Operating conditions .................................................................3
Table 3. Electrical characteristics VCC = +0.9 V, Tamb = 25 °C, VICM = 0 V (unless otherwise specified). ..............4
Table 4. Electrical characteristics VCC = +1.2 V, Tamb = 25 °C, VICM = VCC/2 (unless otherwise specified). ............6
Table 5. Electrical characteristics VCC = +2.7 V, Tamb = 25 °C, VICM = VCC/2 (unless otherwise specified). ............8
Table 6. Electrical characteristics VCC = +5 V, Tamb = 25 °C, VICM = VCC/2 (unless otherwise specified). ............. 10
Table 7. SC70-5 (or SOT323-5) package mechanical data ............................................ 20
Table 8. SOT23-5 mechanical data............................................................. 21
Table 9. DFN8 2x2 package mechanical data ..................................................... 23
Table 10. MiniSO8 mechanical data ............................................................. 25
Table 11. Order code ....................................................................... 26
Table 12. Document revision history ............................................................. 27
TS880, TS883
List of tables
DS12948 - Rev 1 page 29/31
List of figures
Figure 1. Pin connection TS880 (top view)........................................................2
Figure 2. Pin connection TS883 (top view)........................................................2
Figure 3. Current consumption vs. supply voltage, Vicm=Vcc, output low ................................. 12
Figure 4. Current consumption vs. supply voltage, Vicm=Vcc, output high ................................. 12
Figure 5. Current consumption vs. supply voltage, Vicm=0 V, output low ............................... 12
Figure 6. Current consumption vs. supply voltage, Vicm=0 V, output high ............................... 12
Figure 7. Current consumption vs. input common mode voltage, Vcc=0.9 V, output low ........................ 13
Figure 8. Current consumption vs. input common mode voltage, Vcc=0.9 V, output high ....................... 13
Figure 9. Current consumption vs. input common mode voltage, Vcc=5 V, output low ......................... 13
Figure 10. Current consumption vs. input common mode voltage, Vcc=5 V, output high ........................ 13
Figure 11. Current consumption vs. temperature ................................................... 13
Figure 12. Current consumption vs. toggle frequency ................................................ 13
Figure 13. Input offset voltage vs. input common mode voltage, Vcc=0.9 V ................................. 14
Figure 14. Input hysteresis voltage vs. input common mode voltage, Vcc=0.9 V .............................. 14
Figure 15. Input offset voltage vs. input common mode voltage, Vcc=1.2 V ................................. 14
Figure 16. Input hysteresis voltage vs. input common mode voltage, Vcc=1.2 V .............................. 14
Figure 17. Input offset voltage vs. input common mode voltage, Vcc=5 V .................................. 14
Figure 18. Input hysteresis voltage vs. input common mode voltage, Vcc=5 V ............................... 14
Figure 19. Input offset voltage vs. temperature..................................................... 15
Figure 20. Input hysteresis voltage vs. temperature ................................................. 15
Figure 21. Output voltage drop vs. sink current, Vcc=1.2 V ............................................ 15
Figure 22. Output voltage drop vs. source current, Vcc=1.2 V .......................................... 15
Figure 23. Output voltage drop vs. sink current, Vcc=2.7 V ............................................ 15
Figure 24. Output voltage drop vs. source current, Vcc=2.7 V .......................................... 15
Figure 25. Output voltage drop vs. sink current, Vcc=5 V.............................................. 16
Figure 26. Output voltage drop vs. source current, Vcc=5 V ......................................... 16
Figure 27. Propagation delay TPLH vs. input common mode voltage, Vcc=0.9 V .............................. 16
Figure 28. Propagation delay TPHL vs. input common mode voltage, Vcc=0.9 V .............................. 16
Figure 29. Propagation delay TPLH vs. input common mode voltage, Vcc=1.2 V .............................. 16
Figure 30. Propagation delay TPHL vs. input common mode voltage, Vcc=1.2 V .............................. 16
Figure 31. Propagation delay TPLH vs. input common mode voltage, Vcc=5 V ............................... 17
Figure 32. Propagation delay TPHL vs. input common mode voltage, Vcc=5 V ............................... 17
Figure 33. Propagation delay TPLH vs. input signal overdrive, Vcc=1.2 V ................................... 17
Figure 34. Propagation delay TPHL vs. input signal overdrive, Vcc=1.2 V ................................... 17
Figure 35. Current consumption Vs. input common mode voltage, Vcc=0.9 V, output low........................ 17
Figure 36. Current consumption Vs. input common mode voltage, Vcc=0.9 V, output high ....................... 17
Figure 37. Propagation delay TPLH vs. input signal overdrive, Vcc=5 V .................................... 18
Figure 38. Propagation delay TPHL vs. input signal overdrive, Vcc=5 V .................................... 18
Figure 39. Propagation delay TPLH vs. supply voltage ................................................ 18
Figure 40. Propagation delay TPHL vs. supply voltage ................................................ 18
Figure 41. SC70-5 (or SOT323-5) package outline .................................................. 20
Figure 42. SOT23-5 package outline ........................................................... 21
Figure 43. SOT23-5 recommended footprint ...................................................... 22
Figure 44. DFN8 2x2 package outline ........................................................... 23
Figure 45. DFN8 2x2 recommended footprint...................................................... 24
Figure 46. MiniSO8 package outline ............................................................ 25
TS880, TS883
List of figures
DS12948 - Rev 1 page 30/31
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST
products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST
products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other product or service
names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2019 STMicroelectronics – All rights reserved
TS880, TS883
DS12948 - Rev 1 page 31/31