Product Specification 16GFC RoHS Compliant Long-Wavelength SFP+ Transceiver FTLF1429P3BCV PRODUCT FEATURES Up to 14.025 Gb/s bi-directional data links Hot-pluggable SFP+ footprint Built-in digital diagnostic functions 1310nm DFB laser transmitter Duplex LC connector RoHS compliant and Lead Free Up to 10 km on 9/125m SMF Metal enclosure, for lower EMI 1W maximum power consumption with established link Tri Rate 4.25 / 8.5 / 14.025 Gb/s Fibre Channel through Rate Select Single 3.3V power supply 10GBASE-LR/LW 10G Ethernet Extended operating temperature range: 0C to 70C APPLICATIONS Finisar's FTLF1429P3BCV SFP+ transceivers are designed for use in Fibre Channel links up to 14.025 Gb/s data rate and up to 10 km link length. They are compliant with FC-PI-5 Rev. 6.101 and SFF-8472 Rev 11.03 and SFF-80817. They are compatible with SFF-84322 and applicable portions of SFF-8431 Rev. 4.14. The optical transceivers are compliant per the RoHS Directive 2011/65/EU. See Finisar Application Note AN-2038 for more details. PRODUCT SELECTION FTLF1429P3BCV Finisar Corporation January 2017 Rev. B Page 1 FTLF1429P3BCV Product Specification I. Pin Descriptions Pin 1 2 3 4 5 6 7 Symbol VEET TFAULT TDIS SDA SCA MOD_ABS RS0 8 9 LOS RS1 10 11 12 13 14 15 16 17 18 19 20 VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ TDVEET Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault. Transmitter Disable. Laser output disabled on high or open. 2-wire Serial Interface Data Line (MOD-DEF2) 2-wire Serial Interface Clock (MOD-DEF1) Module Absent, connected to VEET or VEER Rx Rate Select: Open or Low = 4.25 or 8.5 Gb/s Fibre Channel (Low Bandwidth) High = 14.025 Gb/s Fibre Channel (High Bandwidth) Loss of Signal indication. Logic 0 indicates normal operation. Tx Rate Select: Open or Low = 4.25 or 8.5 Gb/s Fibre Channel (Low Bandwidth) High = 14.025 Gb/s Fibre Channel (High Bandwidth) Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Inverted DATA out. AC Coupled Receiver Non-inverted DATA out. AC Coupled Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. AC Coupled. Transmitter Inverted DATA in. AC Coupled. Transmitter Ground (Common with Receiver Ground) Ref. 1 2 3 4 4 4 5 6 5 1 1 1 1 1 Notes: 1. Circuit ground is internally isolated from chassis ground. 2. TFAULT is an open collector/drain output, which should be pulled up with a 4.7k - 10k Ohms resistor on the host board if intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V. A high output indicates a transmitter fault caused by either the TX bias current or the TX output power exceeding the preset alarm thresholds. A low output indicates normal operation. In the low state, the output is pulled to <0.8V. 3. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 4. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.6V. MOD_ABS pulls line low to indicate module is plugged in. 5. Rate select can also be set through the 2-wire bus in accordance with SFF-8472 v. 10.2. Rx Rate Select is set at Bit 3, Byte 110, Address A2h. Tx Rate Select is set at Bit 3, Byte 118, Address A2h. Note: writing a "1" selects maximum bandwidth operation. Rate select is the logic OR of the input state of Rate Select Pin and 2-wire bus. 6. LOS is open collector output. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. Finisar Corporation April 2018 Rev. B1 Page 2 FTLF1429P3BCV Product Specification Pinout of Connector Block on Host Board II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Symbol Vcc TS Min -0.5 -40 TOP RH 0 0 Case Operating Temperature Relative Humidity III. Typ Max 4.2 85 Unit V C 70 85 C % Ref. 1 Electrical Characteristics (TOP = -5 to 85 C, VCC = 3.00 to 3.60 Volts) Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage Receiver Single ended data output swing Data output rise/fall time, 4.25 Gb/s LOS Fault LOS Normal Power Supply Rejection Symbol Vcc Icc Rin Vin,pp VD VEN Vout,pp tr, tf VLOS fault VLOS norm PSR Min 3.15 Typ 200 Max 3.45 300 100 90 2 Vee 350 VccT+0.3 Vee+ 0.8 185 425 120 VccHOST Vee+0.4 2 Vee-0.3 66 Unit V mA mV V V mV ps V V mVpp Ref. 2 2 3 4 5 6 7 7 8 Notes: 1. Non-condensing. 2. Module power consumption never exceeds 1W with established link. 3. AC coupled. 4. Or open circuit. 5. Into 100 ohm differential termination. 6. 20 - 80 %. 7. LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 8. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the power supply filtering network shown on page 23 of the Finisar Corporation April 2018 Rev. B1 Page 3 FTLF1429P3BCV Product Specification Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA)6, September 14, 2000. The Power Supply Rejection applies for a supply voltage range of 3.1 to 3.6 V. 9. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and DJ. 10. For 14.025 and 8.5 Gb/s operation, Deterministic Jitter and Total Jitter are not specified per FC-PI-5 Rev 6.10. Jitter values for gamma T and gamma R are controlled by TDP and stressed receiver sensitivity. IV. Optical Characteristics (TOP = 0 to 70 C, VCC = 3.15 to 3.45 Volts) Parameter Transmitter Output Opt. Power, 14.025 Gb/s Output Opt. Power, 4.25, 8.5 Gb/s Optical Wavelength Spectral Width Optical Modulation Amplitude, 14.025 Gb/s Optical Modulation Amplitude, 4.25, 8.5 Gb/s Transmitter and Dispersion Penalty, 14.025 Gb/s Transmitter and Dispersion Penalty, 8.5 Gb/s Optical Rise/Fall Time, 4.25 Gb/s RIN Receiver Unstressed Receiver OMA Sensitivity, 14.025 Gb/s Unstressed Receiver OMA Sensitivity, 8.5 Gb/s Unstressed Receiver OMA Sensitivity, 4.25 Gb/s Average Received Power Optical Center Wavelength Return Loss LOS De-Assert LOS Assert LOS Hysteresis Symbol Min PO,RH PO,RL OMA OMA TDP TDP tr/ tf -5.0 -5.0 1295 RSENSr RSENSr RSENS4 RxMAX C LOSD LOSA Typ Max +2.0 -1.0 1325 1 631 290 4.4 3.2 90 -130 1260 12 0.063 0.042 0.029 +2.0 1370 -19 -30 0.5 Unit dBm dBm nm nm W W dB dB ps dB/Hz mW mW mW dBm nm dB dBm dBm dB Ref. 1,2 3 4 4,5 6 4,6 7 7 8 9 9 Notes: 1. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations. 2. High Bandwidth Mode. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations. 3. Low Bandwidth Mode. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations. 4. Also specified to meet curves in FC-PI-5 Rev 6.101 Figures 23, 24, and 25, which allow trade-off between wavelength, spectral width and OMA for 4.25 and 8.5 Gb/s operation. 5. 20dB spectral width. 6. Equivalent extinction ratio specification for Fibre Channel. Allows smaller ER at higher average power. 7. For 14.025 and 8.5 Gb/s operation, Jitter values for gamma T and gamma R are controlled by TDP. 8. Unfiltered, 20-80%. Complies with IEEE 802.3 (Gig. E), FC 4x eye masks when filtered. 9. Measured with PRBS 27-1 at 10-12 BER. Finisar Corporation April 2018 Rev. B1 Page 4 FTLF1429P3BCV Product Specification V. General Specifications Parameter Data Rate Bit Error Rate Supported Link Length on 9/125 m SMF , 4.25, 8.5, 14.025 Gb/s Symbol BR BER LMAX1 Min 4.25 Typ Max 14.025 10-12 10 Units Gb/sec km Ref. 1 2 3 Notes: 1. 4x/8x/16x Fibre Channel compliant. 2. Tested with a PRBS 27-1 test pattern for 4.25 and 8.5Gb/s operation. Tested with a PRBS 231-1 test pattern for 14.025Gb/s operation. 3. Distances are based on FC-PI-5 Rev. 6.101 and IEEE 802.3 standards. VI. Environmental Specifications These Finisar 1310nm Extended Temperature SFP+ transceivers have an operating temperature range from -5C to +85C case temperature. Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min 0 -40 Typ Max 70 85 Units C C Ref. Regulatory Compliance Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TUV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request. Finisar Corporation April 2018 Rev. B1 Page 5 FTLF1429P3BCV Product Specification VIII. Digital Diagnostic Functions Finisar FTLF1429P3BCV SFP+ transceivers support the 2-wire serial communication protocol as defined in the SFP MSA6. It is very closely related to the E2PROM defined in the GBIC standard, with the same electrical specifications. The standard SFP serial ID provides access to identification information that describes the transceiver's capabilities, standard interfaces, manufacturer, and other information. Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range. The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification and the SFP Multi Source Agreement. The complete interface is described in Finisar Application Note AN2030: "Digital Diagnostics Monitoring Interface for SFP Optical Transceivers". The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. For more information, please see the SFP MSA documentation3,6 or Finisar Application Note AN-2030. FTLF1429P3BCV transceivers can be used in host systems that require either internally or externally calibrated digital diagnostics. Please note that evaluation board FDB-1027 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface. Finisar Corporation April 2018 Rev. B1 Page 6 FTLF1429P3BCV Product Specification IX. Mechanical Specifications Finisar's FTLF1429P3BCV SFP+ transceivers are compatible with the SFF-84322 specification for improved pluggable form factor. FTLF1429P3BCV Finisar Corporation April 2018 Rev. B1 Page 7 FTLF1429P3BCV Product Specification X. PCB Layout and Bezel Recommendations Finisar Corporation April 2018 Rev. B1 Page 8 FTLF1429P3BCV Product Specification Finisar Corporation April 2018 Rev. B1 Page 9 FTLF1429P3BCV Product Specification XI. References 1. "Fibre Channel - Physical Interfaces -5, INCITS 479-2011 (Defines 4GFC, 8GFC and 16GFC). 2. "Improved Pluggable Formfactor", SFF Document Number SFF-8432, Revision 5.0, July 16, 2007. 3. "Digital Monitoring Interface for Optical Transceivers", SFF Document Number SFF-8472, Revision 11.0. 4. "Enhanced Small Form Factor Pluggable Module `SFP+ `", SFF Document Number SFF-8431, Revision 4.1, July 6, 2009. 5. Directive 2011/65/EU of the European Council Parliament and of the Council, "on the restriction of the use of certain hazardous substances in electrical and electronic equipment". Certain products may use one or more exemptions as allowed by the Directive. 6. Small Form Factor Pluggable (SFP) Transceiver Multi-source Agreement (MSA), September 14, 2000 which is available as SFF Document Number INF-8074, Revision 1.0 May 12, 2001. 7. "0.8mm Card Edge Connector for 16Gb/s Applications", SFF Document Number SFF-8081, Revision 0.2, December 21, 2009 XII. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1134 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com Finisar Corporation April 2018 Rev. B1 Page 10 FTLF1429P3BCV Product Specification Data subject to change without notice. Finisar Corporation April 2018 Rev. B1 Page 11