AMF AMP* Connector-Specific Kit 768352-1 for EUROLATCH* Connectors Instruction Sheet 408-9840 13MAY93 Rev A PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. AMP hand tools ara intended far occasional use and low volume applications. AMP offers a wide selection of powered application equipment for extended-use, production operations. CONNECTOR-SPECIFIC KIT 768352-1 LOWER Yo VA. UPPER TOOL INSERT LOCATORS TYPICAL APPLICATIONS MANUAL ARBOR FRAME ASSEMBLY 91085-2 (Ref) AMP-LATCH* HAND TOOL KIT BASE ASSEMBLY UNIVERSAL ARBOR TOOL 768338-1 Figure 7 cad 1. INTRODUCTION This instruction sheet describes AMP Connector- Specific Kit 768352-1, lists cable requirements, and describes installation of the kit. (See Figure 1.) The connector-specific kit can be used with AMP-LATCH Hand Tool Kit 768340-1 or Base Assembly Universal Arbor Tool 768338-1 (Figure 1) ) AMP Incorporated, Harrisburg, PA 17105 TOOLING ASSISTANCE CENTER 1-800-722-1111 AMP FAX/PRODUCT INFO 1-800-522-6752 This AMP controled document is subject fo change. For latest revision call the AMP FAX number. Copyright 1993 by AMP Incorporated. Al International Rights Reserved. *Trademark to terminate EUROLATCH Connectors having 1.27 mm [.050-in.] centerline spacing to ribbon cable. Refer to Figure 2 for cable dimensions. The Base Assembly Universal Arbor Tool is powered by either AMP Manual Arbor Frame Assembly 91085-2 or AMP Pneumatic Auto-Cycle Unit 91112-3. tof3 Per EC M-9045, EG 0990-0071-93 ANF AMP Connector-Specific Kit 768352-1 408-9840 For information concerning AMP EUROLATCH centerline spacing to ribbon cable with 26 AWG solid Connectors, refer to AMP Catalog 82012. For or stranded conductors, 28 AWG solid or stranded detailed information on other tooling compo- conductors, or 30 AWG solid conductors. Refer to nents used with Connector-Specific Kit Figure 2 for the recommended cable dimensions. 768352-1, refer to the following instruction sheets: Mee /2e cable must be cut 90 to the edge of the cable; otherwise an improper termination will 408-6732 -- Pneumatic Auto-Cyele Unit result. We suggest you use 2 guillotine-type 91112-3 cable cutter, such as the Carpenter Model 95 408-7777 -- Manual Arbor Frame Assembly which can be purchased from: 91085-2 408-9827 -- Base Assembly Universal Arbor Carpenter Manufacturing Co., inc. Tool 768338-1 Fairgrounds Drive 408-9828 AMP-LATCH Hand Tool Kit Manlius, N.Y. 13207 768340-1 All dimensions on this sheet are in metric units AMP-LATCH HAND TOOL KIT 768340-1 (Ref) [with U.S. customary units in brackets}. (Includes AMP-LATCH Hand Too! Subassembly 768942-1 and Base Assembly Universal Hand Tool 768339-1. Refer to 408-9846 and 408-9826) 2. DESCRIPTION (Figure 1) \ -LOCATORS The connector-specific kit features an upper tool, two locators, and a lower insert. The upper tool applies an even force aver the length of the connector during termination. The lower insert positions the connector on the tooling assembly, and the locators adjust for the different sizes of cables and connectors. Components are marked EL. SLOT OF FLUTED PLATE LOWER INSERT Figure 3 ead 4. CONNECTOR-SPECIFIC KiT INSTALLATION 274. (Figures 3 and 4) [.050 + .003) For hand tool applications, mount the hand tool *A* + 076.003] _ onto a Suitable work surface, whenever possible, NOTE before terminating the connectors. Refer to the ACCUMULATIVE TOLERANCE FOR CABLE CONDUCTORS 1 THROUGH bench-clamping insiructions in 408-9828, 34 1S + 254 [.010] AND THROUGH 60 IS + .38 [015]. packaged with the AMP-LATCH Hand Tool Kit. CONDUCTOR DIMENSION . SIZE (AWG) TYPE qh BP 1. Slide the upper tool onto the upper tool mount. 26 Stranded or Solid 0 889 1.27 mm [.050 IN,] 2. Slide lower insert into slot of fluted plate. 28 _| Stranded or Solid] (0351N] x otal NO. of 3 Install locators into base of tool, as shown in Figure 2 cad 9831 This completes the installation procedure. 3. CABLE REQUIREMENTS NOTE For information conceming termination proce- dures, refer to 408-9828 packaged with the The connector-specific kit will terminate hand tool kit, and 408-9827 packaged with the EUROLATCH Connectors with 1.27 mm [.050 in.] Base Assembly Universal Arbor Tool. 20f3 RevA AMP AMP Connector-Specific Kit 768352-1 408-9840 BASE ASSEMBLY UNIVERSAL ARBOR TOOL 768338-1 (Ref) Q RAM (Ref) UPPER TOOL MOUNT (Ref) LOCATORS SLOT OF FLUTED J 5. CONNECTOR-SPECIFIC KIT INSPECTION Connector-Specific Kit 768352-1 has been inspected and should be verified with the information provided in Figure 5. it is recommended that the connector- specific kit be inspected immediately upon its arrival at your facility (and at regularly scheduled intervals) to ensure that the kit components have not been damaged during handling. For additional information concerning connector- specific kits, or to purchase additional kits, contact your local AMP representative or: CUSTOMER SERVICE (38-35) NUMERICAL PLATE MARKINGS LOWER AMP INCORPORATED INSERT P.O. BOX 3608 HARRISBURG, PA 17105-3608 Figure 4 cad CONNECTOR-SPECIFIC KIT 768352-1 UPPER 9,651.38 spe (Ct) 9.65 [.38] 20.83.82] _. Lt 5.59.22] 307 [- 8.56|.337] = , J 89.92 [3.54] _ LOWER INSERT + d 1, L Eu ty LL 21.84.86] |~______ 9.2 [3.54] ____+ REAR 12.45 |.49] 12,451.49 FRONT LOCATOR t | ma t LOCATOR 4.57[.18] 16.26[.64]| R 1. Fl 16.26[.64) \ 4.57[.18] Oh Cc OEL @. faa rH 22.10.87] 22.10.87] e! 30.73[1.21] e a 30.73 [1.21] LL COMPONENT LIST ITEM NO. PART NUMBER DESCRIPTION QTY 1 543274-1 Upper Tool 1 2 1-543275-2 Lower Insert 1 3 - 768935-1 Rear Locator 1 4 768936-1 Front Locator 1 Figure cad, cad 9839 RevA 3of3