4 This document Is the property of Amphenol Corporation and Is delivered on the express condition that It Is not to be disclosed, reproduced or used, In whole or In part, for manufacture or sala by anyone other than Amphenol Corporation without Its prior concert, & that no right Is granted to disclose or to use any Information In this document. OA y a 20.90240.05 dV 5.104+0.10 20.8040.05 | z 35.5040.10 | 6.4040.10 A 3.9020. 10 1.7040. 10 0.80Full distortion position CUSTOMER DRAWING sucking area for pick and place NOTE 4.3 0.15 P 2 S H S y SS { 0.4040.15 S 2.2040.10 ~ H 2 SECTION AA S 1.70928, 3.000.10 0.90Working position NOTE 4.2 0.65 2.0040.20 REVISIONS SYM ECN DESCRIPTION DATE APPROVED HK4336 RELEASE TO CUSTOMER 03/20/07| IP HK4478 OPTIMIZE SOLDER TAB DESIGN |06/26/07 IP 1. x A 7. &. 9. 3,5020.05 I 2-1.35040.05 | | | T r--4 J hid N S 21.0040.05 2.70 S N S } Housing EDGE Recommended PCB layout NOTES: MATERIAL: A. PIN:BERYLLIUM COPPER B. INSULATOR: 30% GLASSFILLED THERMOPLASTIC LCP OR EQUIVALENT UL94V0, BLACK. FINISH: CONTACT:GOLD FLASH(1 MICRONINCH MIN.) ALL OVER, 50-100 MICROINCH (1.27-2.54 MICRON) NICKEL UNDERPLATED ALL OVER SOLER TAB: 50-100(1.272.54 MICRON) MICROINCH MATTE TIN, 50-100 MICROINCH(1.272.54 MICRON) NICK UDERPLATED ELECTRICAL SPECIFICATIONS: VOLTAGE RATING: 250 VAC MIN CURRENT RATING: 2.0 A MIN DIELECTRIC STRENGTH: 1000 VAC FOR | MINUTE MIN INSULATION RESISTANCE: 1000 MEG OHM MIN CONTACT RESISTANCE: 30 MILL.OHM MAX OPERATION TEMPERATURE: 55 TO +125C PRODUCT WITHSTANDING REFLOW SOLDERING 260 FOR 10S MECHANICAL SPECIFICATIONS: 4.1 DURABILITY: 5,000 CYCLES 4.2 NORMAL FORCE AT MATED POSITION: 100g MIN 4.3 NORMAL FORCE AT FULL DISTORTION: 110g MIN AMPHENOL IDENTIFICATION TO BE MOLDED INTO INSULATOR. PARTS TO BE PACKAGED IN ANTI-STATIC TAPE AND REEL FOR AUTOMATIC PLACEMENT. ALL PACKAGING MATERIALS TO BE APPROVED BY AMPHENOL ENGINEERING. THE CAVITY# IS 0.8+.10mm HIGH WITH 0.102.10mm RECESSED FROM SURFACE. THE Amphenol LOGO IS 0.84.70mm HIGH WITH 0.1024.10mm RECESSED FROM SURFACE. THE ORDER P/N IS C BC2040L02-001. 10. MATERIAL SHOULD BE FUFILLED AMPHENOL SPEC#SSNOO1. UNLESS OTHERWISE SPECIFIED TOLERANCES U.S. METRIC XxX 4+/- 0.25 XX +/- 0.20 XXX +/- FRACTIONS +/- ANGLES +/- z APPROVAL DATE Amphenol FOR MATERIALS AND FINISHES SEE NOTES \DRAWING\ BC\ CBC2040L02001-B DRAWN | ly.yi 06/26/07 CHECKED| DB.Gao (06/26/07 CHECKED DRAWING FILE : REMOVE SHARP EDGES ANGLE OF PROJECTION DIMENSIONS HS | TNOHES- (METRIC) (MM) TITLE 2 Pins SMT Battery Connector SIZE | DRAWING NO. REV. A3IC BC-2040L02-O001| B SCALE | NONE | SHEET 1 OF 1 1