SS-214 R3 printer's spr. 3/13/01 3:27 PM Page 1 KOA SPEER ELECTRONICS, INC. SS-214 R3 Chip Inductors Type KQ 0603 CERTIFIED 1. Scope of Application This specification applies to chip inductors KQ series produced by KOA corporation. 2. Type Designation Type designation shall be as the following form. KQ 0603 TE R12 J Type Component Size Packaging Nominal Inductance Tolerance Winding Form .063 x .039 x .035 in. 1.6 x 1.0 x 0.9 mm TE: Embossed Taping No Designation: Bulk 1N8----1.8 nH R12----120 nH G:2% J:5% K:10% 3. Rating Item Nominal inductance range Nominal inductance tolerance Q (Quality factor) Self-resonant frequency (MHz) DC resistance (ohm) Allowable current (mA) Measurement frequency (MHz) Storage temperature range Operating temperature range Specification 1.6 nH ~ 390 nH The rating shall be shown in the Table-1 -40C ~ +100C -40C ~ +125C PAGE 1 OF 8 Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com SS-214 R3 printer's spr. 3/13/01 3:27 PM Page 2 KOA SPEER ELECTRONICS, INC. SS-214 R3 Table-1 Ordering Code* KQ0603TE1N6 SelfAllowable Measuring DC Inductance Quality Inductance Tolerance Factor Resonant Resistance DC Current Frequency (MHz) min. Frequency max. () max. (mA) (%) min. (MHz) 1.6 nH 24 12500 0.03 700 250 KQ0603TE1N8 1.8 nH KQ0603TE3N6 3.6 nH KQ0603TE3N9 3.9 nH KQ0603TE4N3 16 12500 0.045 700 250 22 6900 0.063 700 250 22 6900 0.08 700 250 4.3 nH 22 5900 0.063 700 250 KQ0603TE4N7 4.7 nH 20 5800 0.116 700 250 KQ0603TE6N8 6.8 nH 27 5800 0.11 700 250 KQ0603TE7N5 7.5 nH 28 4800 0.106 700 250 KQ0603TE8N7 8.7 nH 28 4600 0.109 700 250 KQ0603TE10N 10 nH 31 4800 0.13 700 250 KQ0603TE11N 11 nH 33 4000 0.086 700 250 KQ0603TE12N 12 nH 35 4000 0.13 700 250 KQ0603TE15N 15 nH 35 4000 0.17 700 250 KQ0603TE16N 16 nH 34 3300 0.104 700 250 KQ0603TE18N 18 nH 35 3100 0.17 700 250 KQ0603TE22N 22 nH 38 3000 0.19 700 250 KQ0603TE24N 24 nH 37 2650 0.135 700 250 KQ0603TE27N 27 nH 40 2800 0.22 600 250 KQ0603TE30N 30 nH 37 2250 0.144 600 250 KQ0603TE33N 33 nH 40 2300 0.22 600 250 KQ0603TE36N 36 nH 38 2080 0.25 600 250 KQ0603TE39N 39 nH 40 2200 0.25 600 250 KQ0603TE43N 43 nH 39 2000 0.28 600 250 KQ0603TE47N 47 nH 38 2000 0.28 600 200 KQ0603TE56N 56 nH 38 1900 0.31 600 200 KQ0603TE68N 68 nH 37 1700 0.34 600 200 : Tolerance character (G,J,K) Bolivar Drive P.O. Box 547 J (5%) K (10%) G (2%) J (5%) K (10%) G (2%) J (5%) * TE: Embossed plastic Bradford, PA 16701 USA 814-362-5536 PAGE 2 OF 8 Fax 814-362-8883 www.koaspeer.com SS-214 R3 printer's spr. 3/13/01 3:27 PM Page 3 KOA SPEER ELECTRONICS, INC. SS-214 R3 Table-1 Continued Ordering Code* KQ0603TE72N SelfAllowable Measuring DC Inductance Quality Resonant Resistance DC Current Frequency Inductance Tolerance Factor (MHz) min. Frequency max. () max. (mA) (%) min. (MHz) 72 nH 34 1700 0.49 400 150 KQ0603TE82N 82 nH 34 1700 0.54 400 150 KQ0603TER10 100 nH 34 1400 0.58 400 150 KQ0603TER11 110 nH 32 1350 0.61 300 150 KQ0603TER12 120 nH 32 1300 0.65 300 150 32 1400 1.4 160 150 G (2%) J (5%) KQ0603TER15 150 nH KQ0603TER18 180 nH 25 1300 2.2 140 100 KQ0603TER22 220 nH 25 1200 2.5 120 100 KQ0603TER27 270 nH 24 900 2.3 170 100 KQ0603TER33 330 nH 30 800 3.0 100 100 KQ0603TER39 390 nH 30 700 3.7 80 100 : Tolerance character (G,J,K) * TE: Embossed plastic 4. Dimensions 5. Construction PAGE 3 OF 8 Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com SS-214 R3 printer's spr. 3/13/01 3:27 PM Page 4 KOA SPEER ELECTRONICS, INC. SS-214 R3 6. Marking of Inductance The marking of nominal inductance consists of only one-figure as detailed below: Value 1.6 nH 1.8 nH 3.6 nH 3.9 nH 4.3 nH 4.7 nH 6.8 nH 7.5 nH 8.7 nH 10 nH Number C 0 E 1 F G 2 H J 3 Value 11 nH 12 nH 15 nH 16 nH 18 nH 22 nH 24 nH 27 nH 30 nH 33 nH Number K 4 5 L 6 7 M 8 N 9 Number P 0 Q 1 2 3 4 5 6 7 Value 36 nH 39 nH 43 nH 47 nH 56 nH 68 nH 72 nH 82 nH 100 nH 110 nH Value 120 nH 150 nH 180 nH 220 nH 270 nH 330 nH 390 nH Number 8 9 0 1 2 3 4 No tolerance of inductance shall be indicated. 7. Measurement Method Nominal Inductance Range 1.6 nH to 390 nH Test Equipment Fixture Setup Measuring Frequency 4291A RF Impedance analyzer 16193A Test fixture E.L = 1.4 cm OSC = 500 mV Listed Table-1 8. Test Conditions Unless otherwise specified, the test shall be performed at the temperature of 20 15C and at a relative humidity of 65 20%. Reverse test conditions shall be performed at the temperature of 20 2C and at a relative humidity of 65 5%. PAGE 4 OF 8 Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com SS-214 R3 printer's spr. 3/13/01 3:27 PM Page 5 KOA SPEER ELECTRONICS, INC. SS-214 R3 9. Reliability Tests 9-1 Electrical Characteristics Item Dielectric withstanding voltage Requirement No evidence of flaming, fuming, or breakdown Test Methods 5 seconds at AC 500 V applied between both terminals and film. Insulation resistance 1000M and over 1 minute at DC 100 V measured between both terminals and film. Flammability Withstands needle-flame test. IEC 695-2-2 9-2 Mechanical Characteristics Item Terminal pull strength Requirement No evidence of damage Test Methods Terminals shall withstand a pull of 10 N (0805 + 1008) and 5 N (0402 + 0603) in a horizontal direction. Terminal bending strength No evidence of breakdown Specimen shall be soldered on bend test board and force applied to the opposite side to cause a 3 mm deflection Vibration L/L within 5% Q/Q within 10% 2 hours in each direction of X, Y, Z, on PCB at a frequency range of 10-55-10Hz with 1.5 mm amplitude Dropping No evidence of damage L/L within 5% Q/Q within 10% Dropping 1 m on the ground of concrete 1 time Resistance to soldering heat No evidence of outer damage L/L within 5% Q/Q within 10% Immerse in the solder at 260 5C for 101 seconds Solderability 95% of the terminal should be covered with new solder Immerse in the solder at 230 5C for 3 0.5 seconds Resistance to solvent No damage and marking must remain legible Accordance with MIL-STD-202F Method 215 PAGE 5 OF 8 Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com SS-214 R3 printer's spr. 3/13/01 3:27 PM Page 6 KOA SPEER ELECTRONICS, INC. SS-214 R3 9-3 Environmental Characteristics Item Low temperature storage Requirement No evidence of damage L/L within 5% Q/Q within 10% Test Methods Store at -40 2C, for 1000 hours High temperature storage No evidence of damage L/L within 5% Q/Q within 10% Store at +125 2C, for 1000 hours Moisture endurance No evidence of damage L/L within 5% Q/Q within 10% Store at 40 2C, 90 ~ 95% RH for 1000 hours Load life No evidence of damage L/L within 5% Q/Q within 10% Biased to full rated current at +125C for 1000 hours High temperature High humidity No evidence of damage L/L within 5% Q/Q within 10% Biased to 10% rated current at +85C, 85% RH for 1000 hours Thermal shock No evidence of damage L/L within 5% Q/Q within 10% 100 cycles between -40C/hour and +125C/hour Temperature characteristics L/L within 5% L/L to be measured at the temperature of between -40C and +125C as based on the inductance at 20C Unless otherwise specified, measurements shall be performed within 2 hours after leaving test samples for more than one hour at the normal temperature and at the normal humidity. 10. Packaging 10-1 Bulk packaging (1) 200 piece chip inductors are packed in a poly bag. (2) Inner box indicates Type (KQ 0603), Nominal inductance, Tolerance, Quantity, Production lot number, Manufacturer's name or Trade mark. Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 10-2 Taping The tapes for taping shall be embossed carrier tapes of .315" (8 mm) width and .157" (4 mm) pitches. The standard quantity per reel shall be 2,000 pieces. PAGE 6 OF 8 814-362-5536 Fax 814-362-8883 www.koaspeer.com SS-214 R3 printer's spr. 3/13/01 3:27 PM Page 7 KOA SPEER ELECTRONICS, INC. SS-214 R3 (1) Dimensions of Carrier Tape .010 (0.25 0.05) Feeding hole* .059 .043 (1.5 0.1 (1.1 0.05) 0 ) Chip pocket .069 (1.75 0.1) .138 (3.5 0.05) .315 (8.0 0.1) Chip inductor .047 .069 .157 .157 (1.2 0.1) (1.75 0.1) (4.0 0.1) (4.0 0.1) Dimensions in inches (mm) .024 .079 * 10 Pitches accumulation of feeding (0.6 0.05) (2.0 0.05) holes shall be 1.57" (40 0.2 mm). Top tape peeling strength: 0.1 N ~ 0.7N Tape running direction (2) Taped Configurations (conforming to EIA-481 standard) Empty space Chip mounting space Empty space Leader space End Beginning 9.04 (230) min. 6.29 (160) min. Dimensions in inches (mm) 6.29 (160) min. Drawing out direction (3) Reel Dimensions and Indication .448 (11.4 1.0) The following items shall be indicated on the reel. .079 (2.0 0.5) .511 (13 0.2) 2.36 (60 1.0) .826 (21 0.8) Indicate position .354 (9.0 0.3) 7.08 (180 +0-3 ) Dimensions in inches (mm) Bolivar Drive P.O. Box 547 * Type (KQ 0603 TE) * Nominal inductance and tolerance * Quantity * Production lot number * Manufacturer's name or trade mark PAGE 7 OF 8 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com SS-214 R3 printer's spr. 3/13/01 3:27 PM Page 8 KOA SPEER ELECTRONICS, INC. SS-214 R3 11. General Information (1) Storage Chip inductors shall not be stored under high temperature and high humidity conditions. Especially, do not store taping where they are exposed to heat or direct sunlight. Otherwise, the packing material may be deformed, causing problems during mounting. (2) Mounting Placement force should not be excessive. (3) Soldering Flow soldering should be done at 260C for less than 10 seconds. Reflow soldering should be done at 240C for less than 30 seconds. When using a soldering iron, temperature shall not exceed 350C and within 3 seconds. Soldering iron time of each electrode shall be allowed only one time. After soldering, chip inductors shall not be stressed excessively. (5) Pattern design The land pattern is recommended as follows. .076 (1.92) Inductor position .040 (1.02) .025 (0.64) Solder resist .006 (0.16) Dimensions in inches (mm) (4) Cleaning It is no problem to use organic solvents. Since this chip inductor is a coil of ultrafine wire, it is susceptible to vibration. If an ultra-sonic cleaning unit is used for cleaning, check for any possibility of problem generation before practical use since such cleaning units considerably differ in vibration level and mode. Although the conditions differ depending on the printed board size, ultrasonic cleaning is generally used in the conditions described below as examples. Power: Within 20 W/L Cleaning times: Within 5 minutes PAGE 8 OF 8 Bolivar Drive AHA 02/01 P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com Notice: The information contained in this Spec Sheet is believed to be accurate and up-to-date. KOA Speer Electronics reserves this right to change these specifications without notice.