TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 1 8 2 7 3 6 4 5 GND RT DTC SCP 3 2 1 20 19 NC GND FK PACKAGE (TOP VIEW) NC D OUT VCC COMP FB OUT D D, JG OR P PACKAGE (TOP VIEW) Complete PWM Power Control 3.6-V to 40-V Operation Internal Undervoltage-Lockout Circuit Internal Short-Circuit Protection Oscillator Frequency . . . 20 kHz to 500 kHz Variable Dead Time Provides Control Over Total Range 3% Tolerance on Reference Voltage (TL5001A) Available in Q-Temp Automotive HighRel Automotive Applications Configuration Control / Print Support Qualification to Automotive Standards NC D D D D D D NC 4 18 NC VCC 5 17 RT NC 6 16 NC COMP 7 15 DTC description NC SCP NC FB NC The TL5001 and TL5001A incorporate on a single NC 8 14 NC monolithic chip all the functions required for a 9 10 11 12 13 pulse-width-modulation (PWM) control circuit. Designed primarily for power-supply control, the TL5001/A contains an error amplifier, a regulator, an oscillator, a PWM comparator with a dead-time-control input, undervoltage lockout (UVLO), short-circuit protection (SCP), and an open-collector output transistor. The TL5001A has a typical reference voltage tolerance of 3% compared to 5% for the TL5001. The error-amplifier common-mode voltage ranges from 0 V to 1.5 V. The noninverting input of the error amplifier is connected to a 1-V reference. Dead-time control (DTC) can be set to provide 0% to 100% dead time by connecting an external resistor between DTC and GND. The oscillator frequency is set by terminating RT with an external resistor to GND. During low VCC conditions, the UVLO circuit turns the output off until VCC recovers to its normal operating range. The TL5001C and TL5001AC are characterized for operation from - 20C to 85C. The TL5001I and TL5001AI are characterized for operation from - 40C to 85C. The TL5001Q and TL5001AQ are characterized for operation from - 40C to 125C. The TL5001M and TL5001AM are characterized for operation from - 55C to 125C. AVAILABLE OPTIONS PACKAGED DEVICES TA - 20C to 85C - 40C to 85C - 40C to 125C SMALL OUTLINE (D) PLASTIC DIP (P) CERAMIC DIP (JG) CHIP CARRIER (FK) TL5001CD TL5001CP -- -- TL5001ACD TL5001ACP -- -- TL5001ID TL5001IP -- -- TL5001AID TL5001AIP -- -- -- -- TL5001QD -- TL5001AQD -- -- -- TL5001MJG TL5001MFK -- -- TL5001AMJG TL5001AMFK - 55C to 125C -- -- The D package is available taped and reeled. Add the suffix R to the device type (e.g., TL5001CDR). Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2002, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. * DALLAS, TEXAS 75265 1 TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 schematic for typical application VI + TPS1101 VO + 2 VCC 5 SCP VO COMP 1 3 TL5001/A 6 7 DTC FB 4 RT GND 8 functional block diagram VCC 2 DTC 6 RT 7 OUT 1 UVLO IDT 2.5 V 1V 1.5 V Error Amplifier Reference Voltage 1V SCP Comparator 1 OSC PWM/DTC Comparator + FB COMP 4 - 3 SCP Comparator 2 SCP 5 8 GND 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 detailed description voltage reference A 2.5-V regulator operating from VCC is used to power the internal circuitry of the TL5001 and TL5001A and as a reference for the error amplifier and SCP circuits. A resistive divider provides a 1-V reference for the error amplifier noninverting input which typically is within 2% of nominal over the operating temperature range. error amplifier The error amplifier compares a sample of the dc-to-dc converter output voltage to the 1-V reference and generates an error signal for the PWM comparator. The dc-to-dc converter output voltage is set by selecting the error-amplifier gain (see Figure 1), using the following expression: VO = (1 + R1/R2) (1 V) Compensation Network R1 VI(FB) 3 COMP 4 FB TL5001/A - R2 + 8 GND To PWM Comparator Vref = 1 V Figure 1. Error-Amplifier Gain Setting The error-amplifier output is brought out as COMP for use in compensating the dc-to-dc converter control loop for stability. Because the amplifier can only source 45 A, the total dc load resistance should be 100 k or more. oscillator/PWM The oscillator frequency (fosc) can be set between 20 kHz and 500 kHz by connecting a resistor between RT and GND. Acceptable resistor values range from 15 k to 250 k. The oscillator frequency can be determined by using the graph shown in Figure 5. The oscillator output is a triangular wave with a minimum value of approximately 0.7 V and a maximum value of approximately 1.3 V. The PWM comparator compares the error-amplifier output voltage and the DTC input voltage to the triangular wave and turns the output transistor off whenever the triangular wave is greater than the lesser of the two inputs. dead-time control (DTC) DTC provides a means of limiting the output-switch duty cycle to a value less than 100 %, which is critical for boost and flyback converters. A current source generates a reference current (IDT) at DTC that is nominally equal to the current at the oscillator timing terminal, RT. Connecting a resistor between DTC and GND generates a dead-time reference voltage (VDT), which the PWM/DTC comparator compares to the oscillator triangle wave as described in the previous section. Nominally, the maximum duty cycle is 0 % when VDT is 0.7 V or less and 100 % when VDT is 1.3 V or greater. Because the triangle wave amplitude is a function of frequency and the source impedance of RT is relatively high (1250 ), choosing RDT for a specific maximum duty cycle, D, is accomplished using the following equation and the voltage limits for the frequency in question as found in Figure 11 (Voscmax and Voscmin are the maximum and minimum oscillator levels): POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 dead-time control (DTC) (continued) R DT + Rt ) 1250 ) Voscmin D V oscmax - V oscmin Where RDT and Rt are in ohms, D in decimal Soft start can be implemented by paralleling the DTC resistor with a capacitor (CDT) as shown in Figure 2. During soft start, the voltage at DTC is derived by the following equation: V DT [ IDTRDT 1- e -t R C DT DT 6 DTC CDT TL5001/A RDT Figure 2. Soft-Start Circuit If the dc-to-dc converter must be in regulation within a specified period of time, the time constant, RDTCDT, should be t0/3 to t0/5. The TL5001/A remains off until VDT 0.7 V, the minimum ramp value. CDT is discharged every time UVLO or SCP becomes active. undervoltage-lockout (UVLO) protection The undervoltage-lockout circuit turns the output transistor off and resets the SCP latch whenever the supply voltage drops too low (approximately 3 V at 25C) for proper operation. A hysteresis voltage of 200 mV eliminates false triggering on noise and chattering. short-circuit protection (SCP) The TL5001/A includes short-circuit protection (see Figure 3), which turns the power switch off to prevent damage when the converter output is shorted. When activated, the SCP prevents the switch from being turned on until the internal latching circuit is reset. The circuit is reset by reducing the input voltage until UVLO becomes active or until the SCP terminal is pulled to ground externally. When a short circuit occurs, the error-amplifier output at COMP rises to increase the power-switch duty cycle in an attempt to maintain the output voltage. SCP comparator 1 starts an RC timing circuit when COMP exceeds 1.5 V. If the short is removed and the error-amplifier output drops below 1.5 V before time out, normal converter operation continues. If the fault is still present at the end of the time-out period, the timer sets the latching circuit and turns off the TL5001/A output transistor. 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 short-circuit protection (SCP) (continued) 2.5 V RSCP 185 k 12 k CSCP SCP 5 From Error Amp 1.5 V SCP Comparator 2 To Output Drive Logic Q1 Vref = 1 V SCP Comparator 1 Q2 Figure 3. SCP Circuit The timer operates by charging an external capacitor (CSCP), connected between the SCP terminal and ground, towards 2.5 V through a 185-k resistor (RSCP). The circuit begins charging from an initial voltage of approximately 185 mV and times out when the capacitor voltage reaches 1 V. The output of SCP comparator 2 then goes high, turns on Q2, and latches the timer circuit. The expression for setting the SCP time period is derived from the following equation: V SCP + (2.5 * 0.185) 1 * e-t ) 0.185 t Where = RSCPCSCP The end of the time-out period, tSCP, occurs when VSCP = 1 V. Solving for CSCP yields: C SCP + 12.46 t SCP Where t is in seconds, C in F. tSCP must be much longer (generally 10 to 15 times) than the converter start-up period or the converter will not start. output transistor The output of the TL5001/A is an open-collector transistor with a maximum collector current rating of 21 mA and a voltage rating of 51 V. The output is turned on under the following conditions: the oscillator triangle wave is lower than both the DTC voltage and the error-amplifier output voltage, the UVLO circuit is inactive, and the short-circuit protection circuit is inactive. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 V Amplifier input voltage, VI(FB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 V Output voltage, VO, OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 V Output current, IO, OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 mA Output peak current, IO(peak), OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating ambient temperature range, TA: TL5001C, TL5001AC . . . . . . . . . . . . . . . . . . . . . . - 20C to 85C TL5001I, TL5001AI . . . . . . . . . . . . . . . . . . . . . . . . - 40C to 85C TL5001Q, TL5001AQ . . . . . . . . . . . . . . . . . . . . . - 40C to 125C TL5001M, TL5001AM . . . . . . . . . . . . . . . . . . . . . - 55C to 125C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to 150C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: All voltage values are with respect to network ground terminal. DISSIPATION RATING TABLE PACKAGE TA 25C POWER RATING DERATING FACTOR ABOVE TA = 25C TA = 70C POWER RATING TA = 85C POWER RATING TA = 125C POWER RATING D 725 mW 5.8 mW/C 464 mW 377 mW 145 mW FK 1375 mW 11.0 mW/C 880 mW 715 mW 275 mW JG 1050 mW 8.4 mW/C 672 mW 546 mW 210 mW P 1000 mW 8.0 mW/C 640 mW 520 mW 200 mW recommended operating conditions Supply voltage, VCC Amplifier input voltage, VI(FB) MIN MAX 3.6 40 UNIT V 0 1.5 V Output voltage, VO, OUT 50 V Output current, IO, OUT 20 mA COMP source current 45 COMP dc load resistance 100 A k Oscillator timing resistor, Rt 15 250 k Oscillator frequency, fosc 20 500 kHz TL5001C, TL5001AC - 20 85 TL5001I, TL5001AI - 40 85 TL5001Q, TL5001AQ - 40 125 TL5001M, TL5001AM - 55 125 Operating ambient temperature, temperature TA 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 C TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 electrical characteristics over recommended operating free-air temperature range, VCC = 6 V, fosc = 100 kHz (unless otherwise noted) reference PARAMETER TEST CONDITIONS Output voltage COMP connected to FB Input regulation VCC = 3.6 V to 40 V TA = - 20C to 25C (C suffix) Output voltage change with temperature TA = - 40C to 25C (I suffix) TA = 25C to 85C TL5001C, TL5001I MIN TYP MAX 0.95 1 1.05 2 12.5 - 10 -1 10 - 10 -1 10 - 10 -2 10 TL5001AC, TL5001AI MIN TYP MAX 0.97 UNIT 1 1.03 V 2 12.5 mV - 10 -1 10 - 10 -1 10 - 10 -2 10 mV/V All typical values are at TA = 25C. undervoltage lockout PARAMETER Upper threshold voltage TEST CONDITIONS TL5001C, TL5001I MIN TYP MAX Lower threshold voltage TA = 25C TA = 25C Hysteresis TA = 25C 100 200 TA = 25C 2.1 2.55 Reset threshold voltage All typical values are at TA = 25C. TL5001AC, TL5001AI MIN TYP MAX UNIT 3 3 2.8 2.8 V V 100 200 mV 2.1 2.55 V short-circuit protection PARAMETER SCP threshold voltage TEST CONDITIONS SCP voltage, latched TA = 25C No pullup SCP voltage, UVLO standby No pullup Input source current TA = 25C TL5001C, TL5001I MIN TYP MAX TL5001AC, TL5001AI MIN TYP MAX UNIT 0.95 1.00 1.05 0.97 1.00 1.03 V 140 185 230 140 185 230 mV 60 120 60 120 mV -15 -20 -15 -20 A -10 SCP comparator 1 threshold voltage All typical values are at TA = 25C. -10 1.5 1.5 V oscillator PARAMETER Frequency TEST CONDITIONS TL5001C, TL5001I MIN TYP MAX Rt = 100 k Standard deviation of frequency Frequency change with voltage Frequency change with temperature VCC = 3.6 V to 40 V TA = - 40C to 25C TA = - 20C to 25C TA = 25C to 85C UNIT 100 100 kHz 15 15 kHz 1 1 kHz -4 - 0.4 4 -4 - 0.4 4 kHz -4 - 0.4 4 -4 - 0.4 4 kHz -4 - 0.2 4 -4 - 0.2 4 kHz Voltage at RT All typical values are at TA = 25C. 1 POST OFFICE BOX 655303 TL5001AC, TL5001AI MIN TYP MAX * DALLAS, TEXAS 75265 1 V 7 TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 electrical characteristics over recommended operating free-air temperature range, VCC = 6 V, fosc = 100 kHz (unless otherwise noted) (continued) dead-time control PARAMETER Output (source) current TL5001C, TL5001I MIN TYP MAX TEST CONDITIONS TL5001C TL5001I V(DT) = 1.5 V V(DT) = 1.5 V 0.9 x IRT 0.9 x IRT Duty cycle = 0% Input threshold voltage 0.5 Duty cycle = 100% 1.1 x IRT 1.2 x IRT 0.7 TL5001AC, TL5001AI MIN TYP MAX 0.9 x IRT 0.9 x IRT 1.1 x IRT 1.2 x IRT 0.5 1.3 UNIT 0.7 1.5 1.3 A V 1.5 All typical values are at TA = 25C. Output source current at RT error amplifier PARAMETER TEST CONDITIONS Input voltage TL5001C, TL5001I MIN TYP MAX VCC = 3.6 V to 40 V 0 Input bias current 1.5 - 160 Output voltage swing Positive 1.5 Negative 0 - 500 2.3 0.3 Open-loop voltage amplification TL5001AC, TL5001AI MIN TYP MAX - 160 1.5 0.4 Unity-gain bandwidth 1.5 Output (sink) current VI(FB) = 1.2 V, COMP = 1 V VI(FB) = 0.8 V, COMP = 1 V Output (source) current All typical values are at TA = 25C. 1.5 V - 500 nA 2.3 0.3 80 UNIT V 0.4 V 80 dB 1.5 MHz 100 600 100 600 A - 45 - 70 - 45 - 70 A output PARAMETER TEST CONDITIONS Output saturation voltage IO = 10 mA VO = 50 V, Off state current Off-state TL5001C, TL5001I MIN TYP MAX 1.5 VCC = 0 VO = 50 V VO = 6 V Short-circuit output current All typical values are at TA = 25C. 2 TL5001AC, TL5001AI MIN TYP MAX 1.5 2 10 10 10 10 40 40 UNIT V A mA total device PARAMETER Standby supply current Average supply current All typical values are at TA = 25C. 8 TEST CONDITIONS TL5001C, TL5001I MIN TYP MAX Off state Rt = 100 k POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TL5001AC, TL5001AI MIN TYP MAX UNIT 1 1.5 1 1.5 mA 1.4 2.1 1.4 2.1 mA TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 electrical characteristics over recommended operating free-air temperature range, VCC = 6 V, fosc = 100 kHz (unless otherwise noted) reference PARAMETER TEST CONDITIONS Output voltage TA = 25C TA = MIN to MAX COMP connected to FB Input regulation TA = MIN to MAX VCC = 3.6 V to 40 V Output voltage change with temperature All typical values are at TA = 25C. *Not production tested. TA = MIN to MAX TL5001Q, TL5001M MIN TYP MAX TL5001AQ, TL5001AM MIN TYP MAX 0.95 1.00 1.05 0.97 1.00 1.03 0.93 0.98 1.07 0.94 0.98 1.06 2 12.5 2 12.5 2 *6 2 *6 *- 6 *- 6 UNIT V mV % undervoltage lockout PARAMETER TL5001Q, TL5001M TEST CONDITIONS MIN TYP TL5001AQ, TL5001AM MAX MIN TYP Upper threshold voltage TA = MIN, 25C TA = MAX 3.00 3.00 2.55 2.55 Lower threshold voltage TA = MIN, 25C TA = MAX 2.8 2.8 2.0 2.0 Hysteresis TA = MIN to MAX 100 200 100 200 Reset threshold voltage TA = MIN, 25C TA = MAX 2.10 2.55 2.10 2.55 0.35 0.63 0.35 0.63 UNIT MAX V V mV V All typical values are at TA = 25C. short-circuit protection PARAMETER SCP threshold voltage SCP voltage, latched SCP voltage, UVLO standby Equivalent timing resistance SCP comparator 1 threshold voltage All typical values are at TA = 25C. TEST CONDITIONS TA = MIN, 25C TA = MAX TA = MIN to MAX TA = MIN to MAX No pullup TL5001Q, TL5001M MIN TYP MAX TL5001AQ, TL5001AM MIN TYP MAX 0.95 1.00 1.05 0.97 1.00 1.03 0.93 0.98 1.07 0.94 0.98 1.06 140 185 230 140 185 230 mV 60 120 60 120 mV No pullup TA = MIN to MAX TA = MIN to MAX POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 UNIT V 185 185 k 1.5 1.5 V 9 TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 electrical characteristics over recommended operating free-air temperature range, VCC = 6 V, fosc = 100 kHz (unless otherwise noted) (continued) oscillator PARAMETER TEST CONDITIONS Frequency TL5001Q, TL5001M MIN TYP MAX TL5001AQ, TL5001AM MIN TYP MAX UNIT 100 100 kHz 2 2 kHz 1 1 kHz TA = MIN to MAX TA = MIN to MAX Rt = 100 k Standard deviation of frequency Frequency change with voltage TA = MIN to MAX Frequency change with temperature TA = MIN to MAX VCC = 3.6 V to 40 V Q suffix *- 6 3 *6 *- 6 3 *6 M suffix *- 9 5 *9 *- 9 5 *9 Voltage at RT All typical values are at TA = 25C. *Not production tested. TA = MIN to MAX 1 1 kHz V dead-time control PARAMETER TEST CONDITIONS Output (source) current TA = MIN to MAX TA = 25C Input threshold voltage TA = MIN to MAX V(DT) = 1.5 V Duty cycle = 0% TL5001Q, TL5001M MIN TYP MAX 0.9 x IRT 0.5 Duty cycle = 100% Duty cycle = 0% 1.1 x IRT 0.7 1.3 0.4 Duty cycle = 100% 0.9 x IRT 1.1 x IRT 0.5 UNIT A 0.7 1.5 0.7 1.3 TL5001AQ, TL5001AM MIN TYP MAX 1.3 0.4 1.5 0.7 1.7 1.3 V 1.7 All typical values are at TA = 25C. Output source current at RT error amplifier PARAMETER TL5001Q, TL5001M TEST CONDITIONS MIN Input bias current Output Out ut swing voltage TA = MIN to MAX Positive Negative Open-loop voltage amplification Unity-gain bandwidth Output (sink) current Output (source) current 1.5 TA = MIN to MAX TYP MAX - 160 - 500 2.3 0.3 MIN 1.5 0.4 UNIT TYP MAX - 160 - 500 2.3 0.3 nA V 0.4 V TA = MIN to MAX 80 80 dB TA = MIN to MAX TA = MIN to MAX 1.5 1.5 MHz A TA = MIN, 25C TA = MAX VI(FB) = 1.2 V, COMP = 1 V VI(FB) = 0 0.8 8 V, V COMP = 1 V 100 600 100 600 - 45 - 70 - 45 - 70 - 30 - 45 - 30 - 45 All typical values are at TA = 25C. 10 TL5001AQ, TL5001AM POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 A TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 electrical characteristics over recommended operating free-air temperature range, VCC = 6 V, fosc = 100 kHz (unless otherwise noted) (continued) output PARAMETER TL5001Q, TL5001M MIN TYP MAX TL5001AQ, TL5001AM MIN TYP MAX UNIT IO = 10 mA VO = 50 V, VCC = 0 VO = 50 V 1.5 1.5 V VO = 6 V 40 TEST CONDITIONS Output saturation voltage TA = MIN to MAX Off state current Off-state TA = MIN to MAX Short-circuit output current All typical values are at TA = 25C. TA = MIN to MAX 2 2 10 10 10 10 40 A mA total device PARAMETER TL5001Q, TL5001M TEST CONDITIONS MIN Standby supply current Off state Average supply current All typical values are at TA = 25C. TA = MIN to MAX TA = MIN to MAX Rt = 100 k POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TL5001AQ, TL5001AM TYP MAX 1 1.4 UNIT TYP MAX 1.5 1 1.5 mA 2.1 1.4 2.1 mA MIN 11 TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 PARAMETER MEASUREMENT INFORMATION 2.3 V COMP 1.5 V DTC OSC PWM/DTC Comparator OUT SCP Comparator 1 1V SCP SCP Timing Period SCP Comparator 2 VCC 0V 3V NOTE A: The waveforms show timing characteristics for an intermittent short circuit and a longer short circuit that is sufficient to activate SCP. Figure 4. PWM Timing Diagram 12 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 TYPICAL CHARACTERISTICS OSCILLATION FREQUENCY vs AMBIENT TEMPERATURE OSCILLATOR FREQUENCY vs TIMING RESISTANCE 100 VCC = 6 V DT Resistance = Rt TA = 25C fosc - Oscillation Frequency - kHz fosc - Oscillator Frequency - Hz 1M 100 k 10 k 10 k 100 k VCC = 6 V Rt = 100 k DT Resistance = 100 k 98 96 94 92 90 88 - 50 1M - 25 REFERENCE OUTPUT VOLTAGE vs POWER-SUPPLY VOLTAGE V ref - Reference Output Voltage Fluctuation - % V ref - Reference Output Voltage - V 1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 0 0 1 2 3 4 5 50 75 100 REFERENCE OUTPUT VOLTAGE FLUCTUATION vs AMBIENT TEMPERATURE TA = 25C FB and COMP Connected Together 1.8 25 Figure 6 Figure 5 2 0 TA - Ambient Temperature - C Rt - Timing Resistance - 6 7 8 9 10 VCC - Power-Supply Voltage - V 0.6 0.4 0.2 0 - 0.2 - 0.4 - 0.6 IIIIIIIIIIII IIIIIIIIIIII IIIIIIIIIIII IIIIIIIIIIII IIIIIIIIIIII IIIIIIIIIIII IIIIIIIIIIII IIIIIIIIIIII IIIIIIIIIIII IIIIIIIIIIII IIIIIIIIIIII - 0.8 - 50 VCC = 6 V FB and COMP Connected Together - 25 0 25 50 75 TA - Ambient Temperature - C 100 Figure 8 Figure 7 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 13 TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 TYPICAL CHARACTERISTICS AVERAGE SUPPLY CURRENT vs POWER-SUPPLY VOLTAGE AVERAGE SUPPLY CURRENT vs AMBIENT TEMPERATURE 2 1.3 I CC - Average Supply Current - mA I CC - Average Supply Current - mA Rt = 100 k TA = 25 C 1.5 1 0.5 0 0 10 20 30 VCC = 6 V Rt = 100 k DT Resistance = 100 k 1.2 1.1 1 0.9 0.8 0 - 50 40 - 25 Figure 9 50 75 100 ERROR AMPLIFIER OUTPUT VOLTAGE vs OUTPUT (SINK) CURRENT 3 1.8 VCC = 6 V TA = 25 C VO - Error Amplifier Output Voltage - V PWM Triangle Wave Amplitude Voltage - V 25 Figure 10 PWM TRIANGLE WAVE AMPLITUDE VOLTAGE vs OSCILLATOR FREQUENCY 1.5 1.2 Voscmax (100% duty cycle) 0.9 Voscmin (zero duty cycle) 0.6 0.3 0 10 k VCC = 6 V VI(FB) = 1.2 V TA = 25 C 2.5 2 1.5 1 0.5 0 100 k 1M fosc - Oscillator Frequency - Hz 10 M 0 0.2 Figure 12 POST OFFICE BOX 655303 0.4 IO - Output (Sink) Current - mA Figure 11 14 0 TA - Ambient Temperature - C VCC - Power-Supply Voltage - V * DALLAS, TEXAS 75265 0.6 TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 TYPICAL CHARACTERISTICS ERROR AMPLIFIER OUTPUT VOLTAGE vs AMBIENT TEMPERATURE ERROR AMPLIFIER OUTPUT VOLTAGE vs OUTPUT (SOURCE) CURRENT 2.46 VCC = 6 V VI(FB) = 0.8 V TA = 25 C 2 1.5 1 0.5 60 80 100 20 40 IO - Output (Source) Current - A 2.44 2.43 2.42 2.41 2.40 - 50 0 0 2.45 VCC = 6 V VI(FB) = 0.8 V No Load 120 25 50 75 - 25 0 TA - Ambient Temperature - C Figure 14 Figure 13 ERROR AMPLIFIER OPEN-LOOP GAIN AND PHASE SHIFT vs FREQUENCY ERROR AMPLIFIER OUTPUT VOLTAGE vs AMBIENT TEMPERATURE 40 VCC = 6 V VI(FB) = 1.2 V No Load AV - Error Amplifier Open-Loop Gain - dB VO - Error Amplifier Output Voltage - mV 240 220 100 200 180 160 140 120 - 50 - 25 0 25 50 75 TA - Ambient Temperature - C 100 VCC = 6 V TA = 25 C - 180 30 - 210 20 - 240 AV - 270 10 0 - 330 - 10 - 20 10 k - 300 100 k 1M Error Amplifier Open-Loop Phase Shift 2.5 VO - Error Amplifier Output Voltage - V VO - Error Amplifier Output Voltage - V 3 - 360 10 M f - Frequency - Hz Figure 15 Figure 16 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 15 TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 TYPICAL CHARACTERISTICS OUTPUT DUTY CYCLE vs DTC VOLTAGE SCP TIME-OUT PERIOD vs SCP CAPACITANCE 12 120 Output Duty Cycle - % 100 t SCP - SCP Time-Out Period - ms VCC = 6 V Rt = 100 k TA = 25 C 80 60 40 20 VCC = 6 V Rt = 100 k DT Resistance = 200 k TA = 25 C 10 8 6 4 2 0 0 0 0.5 1.5 1 DTC Voltage - V 2 0 20 40 100 120 OUTPUT SATURATION VOLTAGE vs OUTPUT (SINK) CURRENT DTC OUTPUT CURRENT vs RT OUTPUT CURRENT 2 - 60 VCC = 6 V TA = 25 C DT Voltage = 1.3 V TA = 25 C - 50 VCE - Output Saturation Voltage - V IO(DT) - DTC Output Current - A 80 Figure 18 Figure 17 - 40 - 30 - 20 - 10 0 1.5 1 0.5 0 0 - 10 - 20 - 30 - 40 - 50 - 60 0 IO - RT Output Current - A Figure 19 16 60 CSCP - SCP Capacitance - nF 5 10 15 IO - Output (Sink) Current - mA Figure 20 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 20 TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 APPLICATION INFORMATION VI 5V C1 100 F 10 V R1 470 + Q1 TPS1101 GND L1 20 H 3.3 V C3 0.1 F CR1 MBRS140T3 C2 100 F 10 V 2 C4 1 F + VCC 5 SCP VO C5 0.1 F R2 56 k R3 43 k COMP 1 7 GND 3 U1 TL5001/A 6 C6 0.012 F DTC R5 7.50 k 1% FB R7 2.0 k C7 0.0047 F R4 5.1 k 4 RT R6 3.24 k 1% GND 8 Partial Bill of Materials: U1 TL5001/A Q1 TPS1101 LI CTX20-1 or 23 turns of #28 wire on Micrometals No. T50-26B core C1 TPSD107M010R0100 C2 TPSD107M010R0100 CR1 MBRS140T3 NOTES: A. B. C. D. + Texas Instruments Texas Instruments Coiltronics AVX AVX Motorola Frequency = 200 kHz Duty cycle = 90% max Soft-start time constant (TC) = 5.6 ms SCP TC = 70 msA Figure 21. Step-Down Converter POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 17 TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 MECHANICAL DATA D (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PIN SHOWN 0.050 (1,27) 0.020 (0,51) 0.014 (0,35) 14 0.010 (0,25) M 8 0.008 (0,20) NOM 0.244 (6,20) 0.228 (5,80) 0.157 (4,00) 0.150 (3,81) Gage Plane 0.010 (0,25) 1 7 0- 8 A 0.044 (1,12) 0.016 (0,40) Seating Plane 0.069 (1,75) MAX 0.010 (0,25) 0.004 (0,10) PINS ** 0.004 (0,10) 8 14 16 A MAX 0.197 (5,00) 0.344 (8,75) 0.394 (10,00) A MIN 0.189 (4,80) 0.337 (8,55) 0.386 (9,80) DIM 4040047 / D 10/96 NOTES: B. C. D. E. 18 All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15). Falls within JEDEC MS-012 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TL5001, TL5001A PULSE-WIDTH-MODULATION CONTROL CIRCUITS SLVS084F - APRIL 1994 - REVISED JANUARY 2002 MECHANICAL DATA FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER 28 TERMINALS SHOWN 18 17 16 15 14 13 NO. OF TERMINALS ** 12 19 11 20 10 A B MIN MAX MIN MAX 20 0.342 (8,69) 0.358 (9,09) 0.307 (7,80) 0.358 (9,09) 28 0.442 (11,23) 0.458 (11,63) 0.406 (10,31) 0.458 (11,63) 21 9 22 8 44 0.640 (16,26) 0.660 (16,76) 0.495 (12,58) 0.560 (14,22) 23 7 52 0.740 (18,78) 0.761 (19,32) 0.495 (12,58) 0.560 (14,22) 24 6 68 25 5 0.938 (23,83) 0.962 (24,43) 0.850 (21,6) 0.858 (21,8) 84 1.141 (28,99) 1.165 (29,59) 1.047 (26,6) 1.063 (27,0) B SQ A SQ 26 27 28 1 2 3 4 0.080 (2,03) 0.064 (1,63) 0.020 (0,51) 0.010 (0,25) 0.020 (0,51) 0.010 (0,25) 0.055 (1,40) 0.045 (1,14) 0.045 (1,14) 0.035 (0,89) 0.045 (1,14) 0.035 (0,89) 0.028 (0,71) 0.022 (0,54) 0.050 (1,27) 4040140 / C 11/95 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a metal lid. The terminals are gold-plated. Falls within JEDEC MS-004 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 19 PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) 5962-9958301Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 59629958301Q2A TL5001 MFKB 5962-9958301QPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9958301QPA TL5001M 5962-9958302Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 59629958302Q2A TL5001 AMFKB 5962-9958302QPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9958302QPA TL5001AM TL5001ACD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -20 to 85 5001AC TL5001ACDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -20 to 85 5001AC TL5001ACDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -20 to 85 5001AC TL5001ACDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -20 to 85 5001AC TL5001AID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 5001AI TL5001AIDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 5001AI TL5001AIDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 5001AI TL5001AIDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 5001AI TL5001AIP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -40 to 85 TL5001AIP TL5001AIPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -40 to 85 TL5001AIP TL5001AMFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 59629958302Q2A TL5001 Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) AMFKB TL5001AMJG ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 TL5001AMJG TL5001AMJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9958302QPA TL5001AM TL5001AQD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 5001AQ TL5001AQDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL5001AQDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL5001AQDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL5001CD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -25 to 85 5001C TL5001CDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -25 to 85 5001C TL5001CDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -25 to 85 5001C TL5001CDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -25 to 85 5001C TL5001CP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -25 to 85 TL5001CP TL5001CP-P ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL5001CP TL5001CP-PE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL5001CP TL5001CPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TL5001CPS ACTIVE SO PS 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM T5001 TL5001CPSG4 ACTIVE SO PS 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM T5001 TL5001CPSLE OBSOLETE SO PS 8 TBD Call TI Call TI TL5001CPSR ACTIVE SO PS 8 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2000 Addendum-Page 2 5001AQ -40 to 125 5001AQ 5001AQ -25 to 85 -25 to 85 TL5001CP T5001 Samples PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) TL5001CPSRG4 ACTIVE SO PS 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -25 to 85 T5001 TL5001ID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 5001I TL5001IDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 5001I TL5001IDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 5001I TL5001IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 5001I TL5001IP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -40 to 85 TL5001IP TL5001IPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -40 to 85 TL5001IP TL5001IPSR ACTIVE SO PS 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Z5001 TL5001IPSRG4 ACTIVE SO PS 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Z5001 TL5001MFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 59629958301Q2A TL5001 MFKB TL5001MJG ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 TL5001MJG TL5001MJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9958301QPA TL5001M TL5001QD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 5001Q TL5001QDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL5001QDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TL5001QDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. Addendum-Page 3 5001Q -40 to 125 5001Q 5001Q Samples PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TL5001, TL5001A, TL5001AM, TL5001M : * Catalog: TL5001A, TL5001 * Automotive: TL5001A-Q1, TL5001A-Q1 * Military: TL5001M, TL5001AM NOTE: Qualified Version Definitions: Addendum-Page 4 PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 * Catalog - TI's standard catalog product * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects * Military - QML certified for Military and Defense Applications Addendum-Page 5 PACKAGE MATERIALS INFORMATION www.ti.com 14-Mar-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TL5001ACDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL5001AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL5001AQDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL5001AQDRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL5001CDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL5001CPSR SO PS 8 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1 TL5001IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL5001IPSR SO PS 8 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1 TL5001QDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TL5001QDRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Mar-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TL5001ACDR SOIC D 8 2500 340.5 338.1 20.6 TL5001AIDR SOIC D 8 2500 340.5 338.1 20.6 TL5001AQDR SOIC D 8 2500 367.0 367.0 35.0 TL5001AQDRG4 SOIC D 8 2500 367.0 367.0 35.0 TL5001CDR SOIC D 8 2500 340.5 338.1 20.6 TL5001CPSR SO PS 8 2000 367.0 367.0 38.0 TL5001IDR SOIC D 8 2500 340.5 338.1 20.6 TL5001IPSR SO PS 8 2000 367.0 367.0 38.0 TL5001QDR SOIC D 8 2500 367.0 367.0 35.0 TL5001QDRG4 SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 MECHANICAL DATA MCER001A - JANUARY 1995 - REVISED JANUARY 1997 JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE 0.400 (10,16) 0.355 (9,00) 8 5 0.280 (7,11) 0.245 (6,22) 1 0.063 (1,60) 0.015 (0,38) 4 0.065 (1,65) 0.045 (1,14) 0.310 (7,87) 0.290 (7,37) 0.020 (0,51) MIN 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.023 (0,58) 0.015 (0,38) 0-15 0.100 (2,54) 0.014 (0,36) 0.008 (0,20) 4040107/C 08/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification. Falls within MIL STD 1835 GDIP1-T8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated