SN74LS145 1-of-10 Decoder/Driver Open-Collector The SN74LS145, 1-of-10 Decoder/Driver, is designed to accept BCD inputs and provide appropriate outputs to drive 10-digit incandescent displays. All outputs remain off for all invalid binary input conditions. It is designed for use as indicator/relay drivers or as an open-collector logic circuit driver. Each of the high breakdown output transistors will sink up to 80 mA of current. Typical power dissipation is 35 mW. This device is fully compatible with all TTL families. http://onsemi.com LOW POWER SCHOTTKY * Low Power Version of 74145 * Input Clamp Diodes Limit High Speed Termination Effects GUARANTEED OPERATING RANGES Symbol VCC Parameter Supply Voltage 16 Min Typ Max Unit 4.75 5.0 5.25 V 0 25 70 C TA Operating Ambient Temperature Range VOH Output Voltage - High 15 V IOL Output Current - Low 24 mA 1 PLASTIC N SUFFIX CASE 648 16 1 SOIC D SUFFIX CASE 751B 16 1 SOEIAJ M SUFFIX CASE 966 ORDERING INFORMATION Device Package Shipping SN74LS145N 16 Pin DIP 2000 Units/Box SN74LS145D SOIC-16 38 Units/Rail SN74LS145DR2 SOIC-16 2500/Tape & Reel SN74LS145M SOEIAJ-16 See Note 1 SN74LS145MEL SOEIAJ-16 See Note 1 1. For ordering information on the EIAJ version of the SOIC package, please contact your local ON Semiconductor representative. Semiconductor Components Industries, LLC, 2001 October, 2001 - Rev. 7 1 Publication Order Number: SN74LS145/D SN74LS145 CONNECTION DIAGRAM DIP (TOP VIEW) VCC P0 P1 P2 P3 Q9 Q8 Q7 16 15 14 13 12 11 10 9 8 1 2 3 4 5 6 7 Q0 Q1 Q2 Q3 Q4 Q5 Q6 GND LOADING (Note a) HIGH LOW 0.5 U.L. Open Collector 0.25 U.L. 15 U.L. PIN NAMES P0, P1, P2, P3 Q0 - Q9 BCD Inputs Outputs NOTES: a) 1 TTL Unit Load (U.L.) = 40 A HIGH/1.6 mA LOW. LOGIC SYMBOL 15 14 13 12 P0 P1 P2 P3 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 1 2 3 4 5 6 7 9 10 11 VCC = PIN 16 GND = PIN 8 http://onsemi.com 2 SN74LS145 LOGIC DIAGRAM INPUTS P0 P1 P2 P3 INPUT INVERTERS 0 0 Q0 Q1 1 1 2 Q3 Q4 2 3 3 DECODE/DRIVER GATES Q2 Q5 Q6 Q7 Q8 Q9 OUTPUTS TRUTH TABLE INPUTS OUTPUTS P3 P2 P1 P0 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 L L L L L L L L H H H H H H H H L L L L H H H H L L L L H H H H L L H H L L H H L L H H L L H H L H L H L H L H L H L H L H L H L H H H H H H H H H H H H H H H H L H H H H H H H H H H H H H H H H L H H H H H H H H H H H H H H H H L H H H H H H H H H H H H H H H H L H H H H H H H H H H H H H H H H L H H H H H H H H H H H H H H H H L H H H H H H H H H H H H H H H H L H H H H H H H H H H H H H H H H L H H H H H H H H H H H H H H H H L H H H H H H H = HIGH Voltage Level L = LOW Voltage Level http://onsemi.com 3 SN74LS145 DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified) Limits Symbol Min Parameter VIH Input HIGH Voltage VIL Input LOW Voltage VIK Input Clamp Diode Voltage IOH Output HIGH Current VOL Output Ou u LOW O Voltage o age IIH Input HIGH Current IIL Input LOW Current ICC Power Supply Current Typ Max Unit Test Conditions V Guaranteed Input HIGH Voltage for All Inputs V Guaranteed Input LOW Voltage for All Inputs -1.5 V VCC = MIN, IIN = -18 mA 250 A VCC = MIN, VOH = MAX 0.25 0.4 V IOL = 12 mA 0.35 0.5 V IOL = 24 mA 2.3 3.0 V IOL = 80 mA 2.0 0.8 -0.65 VCC = VCC MIN, VIN = VIL or VIH per T Truth hT Table bl 20 A VCC = MAX, VIN = 2.7 V 0.1 mA VCC = MAX, VIN = 7.0 V -0.4 mA VCC = MAX, VIN = 0.4 V 13 mA VCC = MAX, VIN = GND AC CHARACTERISTICS (TA = 25C) Limits Symbol tPHL tPLH Min Parameter Typ Propagation Delay Pn Input to Qn Output Max Unit Test Conditions 50 50 ns VCC = 5.0 V CL = 45 pF AC WAVEFORMS VIN VOUT 1.3 V VIN 1.3 V tPHL tPLH 1.3 V 1.3 V VOUT Figure 1. 1.3 V 1.3 V tPHL tPLH 1.3 V 1.3 V Figure 2. http://onsemi.com 4 SN74LS145 PACKAGE DIMENSIONS N SUFFIX PLASTIC PACKAGE CASE 648-08 ISSUE R NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. -A- 16 9 1 8 B F C L S -T- SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M T A M http://onsemi.com 5 DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0 10 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0 10 0.51 1.01 SN74LS145 PACKAGE DIMENSIONS D SUFFIX PLASTIC SOIC PACKAGE CASE 751B-05 ISSUE J -A- 16 9 1 8 -B- P NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 8 PL 0.25 (0.010) M B S G R K F X 45 C -T- SEATING PLANE J M D 16 PL 0.25 (0.010) M T B S A S http://onsemi.com 6 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0 7 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0 7 0.229 0.244 0.010 0.019 SN74LS145 PACKAGE DIMENSIONS M SUFFIX SOEIAJ PACKAGE CASE 966-01 ISSUE O 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). LE 9 Q1 M E HE 1 8 L DETAIL P Z D e VIEW P A A1 b 0.13 (0.005) c M 0.10 (0.004) http://onsemi.com 7 DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.18 0.27 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 0 0.70 0.90 --0.78 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 0 0.028 0.035 --0.031 SN74LS145 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800-282-9855 Toll Free USA/Canada http://onsemi.com 8 SN74LS145/D