SPEC NO: DSAJ1448 REV NO: V.2 DATE: NOV/24/2010 PAGE: 1 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1203008949
1.6X0.8mm SMD CHIP LED LAMP
Part Number: APT1608ZGC-AMT Green
Package Dimensions
Features
zHigh reliability LED package.
z1.6mmx0.8mm SMT LED,0.75mm thickness.
zLow power consumption.
zWide viewing angle.
zIdeal for backlight and indicator.
zVarious colors and lens types available.
zPackage: 2000pcs / reel .
zMoisture sensitivity level : level 3.
zRoHS compliant.
Applications
zTraffic signaling.
zBacklighting (illuminated advertising , general lighting).
zInterior and exterior automotive lighting.
zSubstitution of micro incandescent lamps.
zReading lamps.
zSignal and symbol luminaire for orientation.
zMarker lights (e.g. Steps, exit ways, etc).
zDecorative and entertainment lighting.
zIndoor and outdoor commercial and residential
architectural lighting.
Description
The Green source color devices are made with InGaN
on Sapphire Light Emitting Diode.
Static electricity and surge damage the LEDS.
It is recommended to use a wrist band or anti-electrostatic
glove when handling the LEDs.
All devices, equipment and machinery must be electrically
grounded.
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.004") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAJ1448 REV NO: V.2 DATE: NOV/24/2010 PAGE: 2 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1203008949
Selection Guide
Absolute Maximum Ratings at Ta=25°C
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
Part No. Dice Lens Type
Iv (mcd) [2]
@ 20mA
V
iewing
Angle [1]
Code. Min. Max. 2θ1/2
APT1608ZGC-AMT Green (InGaN) Water Clear 120°
Q 300 400
R 400 500
S 500 700
Notes:
1.The dominant Wavelength (λ d) above is the setup value of the sorting machine. (Tolerance λ d : ±1nm. )
2. Forward Voltage: +/-0.1V.
Electrical / Optical Characteristics at Ta=25°C
Notes:
1. Rth(j-a) Results from mounting on PC board FR4 (pad size≥16 mm2 per pad),
2. 1/10 Duty Cycle, 0.1ms Pulse Width.
Parameter Symbol Value Unit
Power dissipation PD 82 mW
Reverse Voltage VR 5 V
Junction temperature TJ 110 °C
Operating Temperature Top -40 To +10 0 °C
Storage Temperature Ts tg -40 To +11 0 °C
DC Forward Current[1] IF 20 mA
Peak Forward Current [2] IFM 150 mA
Electrostatic Discharge Threshold (HBM) 450 V
Thermal Resistance (Junction/ambient) [1] Rth j-a 350 °C/W
Parameter Symbol
Value
Unit
Code. Min. Typ. Max.
Wavelength at peak emission IF=20mA λpeak 515 nm
Dominant Wavelength IF=20mA λ dom [1]
1 513 522
nm
2 518 527
3 523 532
4 528 537
Spectral bandwidth at 50%ΦREL MAX IF=20mA Δλ 30 nm
Forward Voltage IF=20mA VF [2] 3.3 4.1 V
Reverse Current (VR = 5V) IR 50 uA
Temperature coefficient of λpeak
IF=20mA, -10 °C≤ T≤100 °C TC λpeak 0.09 nm/°C
Temperature coefficient of λdom
IF=20mA, -10 °C≤ T≤100 °C TC λdom 0.05 nm/°C
Temperature coefficient of VF
IF=20mA, -10 °C≤ T≤100 °C TCV -2.5 mV/°C
SPEC NO: DSAJ1448 REV NO: V.2 DATE: NOV/24/2010 PAGE: 3 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1203008949
Green APT1608ZGC-AMT
SPEC NO: DSAJ1448 REV NO: V.2 DATE: NOV/24/2010 PAGE: 4 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1203008949
APT1608ZGC-AMT
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Tape Specifications
(Units : mm)
Reel Dimension
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
SPEC NO: DSAJ1448 REV NO: V.2 DATE: NOV/24/2010 PAGE: 5 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1203008949
PACKING & LABEL SPECIFICATIONS APT1608ZGC-AMT
SPEC NO: DSAJ1448 REV NO: V.2 DATE: NOV/24/2010 PAGE: 6 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1203008949
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below
Lot Tolerance Percent Defective (LTPD) : 10%
No. Test Item Standards Test Condition Test Times /
Cycles
Number of
Damaged
1 Continuous operating test - Ta =25°C ,IF = maximum rated current* 1,000 h 0 / 22
2 High Temp. operating test EIAJ ED-
4701/100(101) Ta = 100°C IF = maximum rated current* 1,000 h 0 / 22
3 Low Temp. operating test - Ta = -40°C, IF = maximum rated current* 1,000 h 0 / 22
4 High temp. storage test EIAJ ED-
4701/100(201) Ta = maximum rated storage temperature 1,000 h 0 / 22
5 Low temp. storage test EIAJ ED-
4701/100(202) Ta = -40°C 1,000 h 0 / 22
6 High temp. & humidity storage test EIAJ ED-
4701/100(103) Ta = 60°C, RH = 90% 1,000 h 0 / 22
7 High temp. & humidity operating test EIAJ ED-
4701/100(102)
Ta = 60°C, RH = 90%
IF = maximum rated current* 1,000 h 0 / 22
8 Soldering reliability test EIAJ ED-
4701/100(301)
Moisture soak : 30°C,70% RH, 72h
Preheat : 150~180°C(120s max.)
Soldering temp : 260°C(10s)
3 times 0 / 18
9 Thermal shock operating test - Ta = -40°C(15min) ~ 100°C(15min)
IF = derated current at 100°C 1,000 cycles 0 / 22
10 Thermal shock test - Ta = -40°C(15min) ~ maximum rated
storage temperature(15min) 1,000 cycles 0 / 22
11 Electric Static Discharge (ESD) EIAJ ED-
4701/100(304) C = 100pF , R2 = 1.5KΩ V = 450V Once each
Polarity 0 / 22
12 Vibration test - a = 196m/s² , f = 100~2KHz ,
t = 48min for all xyz axes 4 times 0 / 22
* : Refer to forward current vs. derating curve diagram
Items Symbols Conditions Failure Criteria
luminous Intensity lv IF = 20mA Testing Min. Value <Spec.Min.Value x 0.5
Forward Voltage VF IF = 20mA Testing Max. Value ≥Spec.Max.Value x 1.2
Reverse Current IR VR = Maximum Rated Reverse Voltage Testing Max. Value ≥Spec.Max.Value x 2.5
High temp. storage test - - Occurrence of notable decoloration, deformation
and cracking
Failure Criteria
