Amplifier
print this page ERA-4SM
Frequency
MHz GAIN, dB Maximum Power, dBm Dynamic Range VSWR Absolute
Maximum
Rating DC Power Thermal
resistance
Øjc
°C/W
fL - fUMin. Output
(1 dB
Comp.) Min. Input
(no
damage)
NF
dB
Typ.
IP3
dBm
Typ.
In
DC-3
GHz
In
3-fu
GHz
Out
DC-3
GHz
Out
3-fu
GHz
I
(mA) P
(mW)
Cur-
rent
(mA) Device Volt(V.)
DC-4000 11.00 +17.30 +15.00 +20.00 4.20 34.00 +1.20 1.20 1.30 1.80 120.00 650.00 65.00 4.50 168.00
Lw=low range(fL to fU/2) U=upper range(fU/2 to fU)
Pin Connections
Port RF in RF Out DC Case GND Not Used
cb 1 3 3 2,4 -
Case Style - WW107 (inch,mm ) weight: 0.015 grams.
A B C D E F G H J
.012
0.305 .10
2.540 .020
0.508 .092
2.337 .085
2.159 .060
1.524 .007
0.178 .026
0.660 .235
5.969
K L M N P Q R S T
.118
2.997 .235
5.969 .118
2.997 .072
1.829 .040
1.016 .020
0.508
Tolerance: .x ± .1 .xx ± .03 .xxx ± .015 inch.
Material and Finish:
Case material: plastic. Lead finish: tin-lead plate or tin plate.
Marking:
RF input lead (1) identified by one or both of the following at factory option:
(a) diagonally cut lead, which may be 45°(ref) in either direction;
(b) orientation mark on the case. Model dash number identified by color dot or
alphanumeric code on case. See specification data sheet.
Packaging:
Packaging information:
Tape Width(mm): 12
Reel Size(inches): 7
Device Cavity Pitch(mm): 8
Devices Per Reel: 1000
Notes:
•ERA-SM models available on tape and reel.
•Model number designated by alphanumeric code marking.
•Permanent damage may occur if any of these limits are exceeded. These
ratings are not intended for continuous normal operation.
•Application notes: Improved ERA Amplifiers
•For Amplifier Selection Guide, please click here.
For Amplifier Environmental Specifications, please click here.
•For Surface Mount Environmental Specifications, please click here.
Re-flow soldering information is available in "Surface Mount" article.
•Low frequency cutoff determined by external coupling capacitors.
•Gain, VSWR at 2 GHz.
•Maximum Power, NF, IP3 at 1 GHz.
•fU is the upper frequency limit for each model as shown in the table.
•Non-hermetic
•Absolute maximum ratings:
Operating temperature: -45°C to 85°C,
Storage temperature: -65° to 150°C,
Device voltage:
4.2V min., 5.5V max.
•Typical Biasing Configuration ERA/MAR/MAV/RAM/VAM
•Supply voltage must be connected to pin 3 through a bias resistor in order
to prevent damage. See Biasing MMIC Amplifiers. Reliability predictions
are applicable at specified current and normal operating conditions.
•General Quality Control Procedures and Environmental Specifications are
given in Mini- Circuits Guarantees Quality.
Hi-Rel, MIL description are given in Hi-Rel and MIL
•Prices and Specifications subjects to change without notice.
Typical Performance Data