ELECTRICAL SPECIFICATIONS: 1.0 INDUCTANCE P2-J2@=P3-J3=P5-J5 2.0 DC RESISTANCE Pe-J2@=P3-J3=P5-J5 3.0 COMMON MODE ATTENUATION: FREQUENCY (MHz) 1 10 30 70 200 300 PS @ @ Pe @ |@ |@ + 30 uH MIN. 0.01V, 10 KHz, : 0.5 ohm MAX CMACOB> o 15 15 20 17 6 334 InNet Technologies Inc. http://www.innettech.com Stewart Connector Systems http://www.stewartconnector.com wior 3 PEE Sie c0146 REV. X +| * 545 [13.84] MAX -- fu SS * 608 [15.44, J CT720059X1 /24002701 |+ 850 [21.59] MAX.~] = 148 [3.75] HIGHEST POINT OF BEAM = 2 5g = i 2 8 z a S N _ : 5 6G) = re 083 [2.12] Z a oT HIGHEST POINT 1.02] OF BEAM 495 [10.79] + 050 [1.27] TYP TOL NON-ACCUM 025 [0.64] 100 [2.54] TYP TOL NON-ACCUM 9.035 [0.89] (6) S +t 8 +h 100 [2.54] 250 [6.35] 6.062 [1.57] (2) ees 128 [3.25] 125 [3.18] (2) 120 [3.05] * 400 [10.16] * 530 [13.46] P.C.B. RECOMMENDED HOLE LAYOUT SEEN FROM. COMPONENT SIDE TOLERANCE +.003 [0.08] UNLESS OTHERWISE SPECIFIED NOTES: TOLERANCES COMPLY WITH F.C.C. DIMENSION REQUIREMENTS DIMENSIONS SHOWN WITH * TO BE CENTRAL ABOUT CENTER LINE DIMENSIONS SHOWN ARE SUBJECT TO CHANGE WITHOUT NOTICE. PINS WITHOUT ELECTRICAL CONNECTIONS MAYBE OMITTED. SEE ELECTRICAL DRAWING FOR DETAILS. AVAILABLE WITH: STANDARD 50 MICRO-INCH SELECTIVE GOLD PLATING InNet Technologies Inc. http://www.ilnnet-tech.com Stewart Connector Systems http://www.stewartconnector.com OF 3 DRAWING NO. S I _ P 0 1 4 G REV. 0 r 1300 7 1200 1100 yA 1000 900 - 800 7 700 7 600 500 400 i 300 f 200 100 GRAMS OF FORCE / GROUNDING BEAM S S S&S S S FHA Ts | PANEL GROUNDING BEAM DEFLECTION S.0.S. = SUGGESTED OPENING SIZE L 000 (TOP OF PCB TO BOTTOM OF OPENING) -010 MAX. RADIUS(4) SUGGESTED PANEL OPENING CT720059x! POINT OF CONTACT WITH PANEL ~| - .080 > ES4 4 => =|) FF THE SUGGESTED PANEL OPENING IS INTENDED TO GIVE THE USER THE ABILITY TO HAVE REASONABLE JACK / PANEL CLEARANCES YET MAINTAIN RELIABLE GROUNDING CAPABILITY. THESE VARIABLES CAN BE ADJUSTED IN EITHER DIRECTION BUT MAY CARRY SOME CONSEQUENCES IN THE FORM OF LOWER MATING FORCES OR TIGHTER ASSEMBLY TOLERANCES. FORCE VALUES ON THE GRAPH ARE GENERAL AVERAGES TAKEN AT THE POINT OF CONTACT SHOWN ABOVE. THE SUGGESTED PANEL OPENING INCLUDES APPROXIMATELY .020 CLEARANCE ON THE SIDES AND TOP AND .013 ON THE BOTTOM, AT PANEL OPENING. InNet Technologies Inc. http://www.ilnnet-tech.com Stewart Connector Systems http://www.stewartconnector.com 3 OF 3 DRAWING NO. S I _ P 0 1 4 G REV. 0 r