ECS25/45/60 COVER - XP POWER

Notes

1. Safety approvals cover frequency 47-63 Hz.

2. ECS60US12 1.5% pk-pk, 20 MHz bandwidth under certain line/load conditions.

3. See longform datasheet or contact sales for details.

AC-DC

Specification

25-60 Watts

•IT & Medical Safety Approvals

•Very Small 2”x 3”x 0.95”Package

•<0.3 W No Load Input Power

•25, 45 & 60 W - Convection Cooled Ratings

•Class I & Class II Installations

•-20 °C to +70 °C Operation

•3 Year Warranty

ECS Series

Input

Input Voltage • 80-264 VAC (120-370 VDC), derate linearly

from 100% at 90 VAC to 80% at 80 VAC

Input Frequency • 47-400 Hz(1)

Input Current • 25 W: 0.45 A, 45 W: 0.75 A, 60 W: 0.95 A

typical at 115 VAC, full load,

25 W: 0.30 A, 45 W: 0.45 A, 60 W: 0.60 A,

typical at 230 VAC, full load

Inrush Current • 40 A max at 230 VAC, cold start 25 ˚C

Power Factor • EN61000-3-2, class A

No Load Input Power • US05, 12 & 24 models: <0.3 W,

US48 and all ECS60 models: <0.5 W

Earth Leakage Current • 260 µA at 264 VAC/60 Hz max,

80/160 µA typical 115/230 VAC

Input Protection • T3.15 A/250 V internal fuse in line

and neutral

Output

Output Voltage • 5-48 VDC (see tables)

Output Voltage Trim • ±10%

Initial Set Accuracy • ±1%

Minimum Load • No minimum load required

Start Up Delay • 1 s typical

Start Up Rise Time • 50 ms

Hold Up Time • 16 ms min at 115 VAC

Drift • ±0.2% after 20 min warm up

Line Regulation • ±0.5% max

Load Regulation • ±1%

Over/Undershoot • 5% typical

Transient Response • 4% max. deviation, recovery to within

1% in 500 µs for a 50-75-50% load

change

Ripple & Noise • 1% pk-pk V1, 20 MHz bandwidth(2)

Overvoltage Protection • 115-140% Vnom, recycle input to reset

Overload Protection • 110-160%

Short Circuit Protection • Continuous trip and restart (hiccup mode)

Temperature • 0.05%/˚C

Coefficient

xppower.com

General

Efficiency • Up to 90%, model dependant

Isolation • 4000 VAC In to Out, 2 x MOPP, 1500 VAC In

to Earth, 1 x MOPP, 500 VDC Out to Earth, 1

x MOPP

Switching Frequency • 65 KHz typical

Power Density • Up to 7.9 W/in3

MTBF • 25 & 45 W: 1072 kHrs, 60 W: 471 kHrs to

MIL-HDBK-217F at 25 ˚C, GB

Environmental

Operating Temperature • -20 ˚C to +70 ˚C derate linearly from +50 ˚C

at 2.5%/˚C to 50% load at +70 ˚C.

Cooling • Convection, see thermal considerations

Operating Humidity • 95% RH, non-condensing

Storage Temperature • -40 ˚C to +85 ˚C

Operating Altitude • 3000 m

Shock • 30 g pk, half sine, 6 axes

Vibration • 2 g rms, 5 Hz to 500 Hz, 3 axes

EMC & Safety

Low Voltage PSU EMC • EN61204-3, high severity level

Emissions • All models: EN55011/22 level B conducted.

45 & 60 W: EN55011/22 level A radiated,

ECS25 & ECS60US24/48 models: level B

radiated

Harmonic Currents • EN61000-3-2, class A

Voltage Flicker • EN61000-3-3

Radiated Immunity • EN61000-4-3, level 3 Perf Criteria A

EFT/Burst • EN61000-4-4, level 3 Perf Criteria A

Surge • EN61000-4-5, installation class 3

Perf Criteria A

Conducted Immunity • EN61000-4-6, level 3 Perf Criteria A

Dips & Interruptions • EN61000-4-11 , 30% 10 ms, 60% 100 ms,

100% 5000 ms, Perf Criteria A, B, B ,

EN60601-1-2, 30% 500 ms, 60% 100 ms,

100% 10 ms, 100% 5000 ms, Perf Criteria

A, A, A, B - 230 VAC. Consult longform

datasheet for 115 V operation.

Safety Approvals • IEC60950-1 CB report, UL60950-1,

TUV EN60950-1, IEC60601-1 CB report,

ANSI/AAMI ES60601-1, TUV 60601-1,

Including Risk Management

Equipment Protection • Class I and Class II

Class

AC-DC

0.95 (24.2) 0.14 (3.6)

SMD Height

1.75

(44.4)

0.25 (0.6) Faston Ground Tab

1.65

(41.8)

1.31

(33.3)

3.00 (76.2)

2.00

(50.8)

0.27

(7.0)

0.20

(5.1)

C5 C18

2.75 (69.8) 4 x Ø.156 (3.96) Mounting Holes

Ø.312 (7.92) Clearance Top and Bottom

ECS25

Models and Ratings

Mechanical Details

Notes

1. All dimensions in inches (mm).

Tolerance .xx = ±0.02 (0.50); .xxx = ±0.01 (0.25)

2. Weight 0.22 lbs (100 g)

Notes

1. All dimensions in inches (mm).

Tolerance .xx = ±0.02 (0.50); .xxx = ±0.01 (0.25)

2. Weight 0.5 lbs (230 g)

Notes

1. For covered versions, add suffix ‘-C’ to model number or order part number ECS25-60 COVER KIT for standalone cover. Not suitable for use in class II installations,

derate output power by 20% with cover.

Output Power Output Voltage Output Current Model Number(1)

25 W 12.0 VDC 2.08 A ECS25US12

25 W 15.0 VDC 1.67 A ECS25US15

25 W 24.0 VDC 1.04 A ECS25US24

25 W 48.0 VDC 0.52 A ECS25US48

J1 mates with Molex Housing PN 09-50-1031,

J2 mates with Molex Housing PN 09-50-1041 and

both with Molex Series 5194 Crimp Terminals

Faston ground tab requires insolated receptacle

In put Connector J1

Molex PN 09-65-2038

Pin 1 Line

Pin 2 Neutral

0.25” Faston Earth

Output Connector J2

Molex PN 09-65-2048

Pin 1 +V1

Pin 2 +V1

Pin 3 RTN

Pin 4 RTN

1.40

(35.6)

0.70

(17.79)

1.23 (31.28)

0.22 (5.7)

3.48

(88.4) 3.03

(76.9)

Output Connector

2J1

Input

Connector Top View

0.63

(16.0)

0.22 (5.7)

3.03

(76.99)

1.26

(32.0)

2.52

(64.0)

Bottom View

4 x M3 x 0.5 THD

0.16 (4.0) Max

Screw Penetration

4 x M3 x 0.5 THD

0.16 (4.0) Max

Screw Penetration

0.25 (0.6) Faston Ground Tab

Covered version (All ECS25-60 Models)

ECS45

Models and Ratings

Mechanical Details

1. For covered versions, add suffix ‘-C’ to model number or order part number ECS25-60 COVER KIT for standalone cover. Not suitable for use in class II installations,

derate output power by 20% with cover.

Notes

AC-DC

Output Power Output Voltage Output Current Model Number(1)

30 W 5.0 VDC 6.00 A ECS45US05

45 W 12.0 VDC 3.75 A ECS45US12

45 W 15.0 VDC 3.00 A ECS45US15

45 W 24.0 VDC 1.90 A ECS45US24

45 W 48.0 VDC 0.95 A ECS45US48

J1 mates with Molex Housing PN

09-50-1031,

J2 mates with Molex Housing PN 09-50-1041 and

both with Molex Series 5194 Crimp Terminals

Faston ground tab requires insolated receptacle

In put Connector J1

Molex PN 09-65-2038

Pin 1 Line

Pin 2 Neutral

0.25” Faston Earth

Out put Connector J2

Molex PN 09-65-2048

Pin 1 +V1

Pin 2 +V1

Pin 3 RTN

Pin 4 RTN

J1 mates with Molex Housing PN 09-50-1031,

J2 mates with Molex Housing

PN 09-50-1041 and both with Molex Series

5194 Crimp Terminals

Faston ground tab requires insolated receptacle

In put Connector J1

Molex PN 09-65-2038

Pin 1 Line

Pin 2 Neutral

0.25” Faston Earth

Out put Connector J2

Molex PN 09-65-2048

Pin 1 +V1

Pin 2 +V1

Pin 3 RTN

Pin 4 RTN

0.14 (3.6) SMD Height Limit

2.75 (69.9)

1.75

(44.5)

0.25 (0.6) Faston Ground Tab

1.58

(40.3)

1.30

(33.0)

3.00 (76.2)

0.28

(7.0)

0.20

(5.1)

1.05

(26.7)

2.00

(50.8)

C18

4 x Ø.156 (3.96) Mounting Holes

Ø.312 (7.92) Clearance Top and Bottom

0.95

(24.2) 0.14 (3.6)

SMD Height

2.75 (69.9)

1.75

(44.5)

1.65

(41.8)

1.31

(33.3)

3.00 (76.2)

2.00

0.28

(7.0)

0.20

(5.1)

C5 C18

0.25 (0.6) Faston Ground Tab

4 x Ø.156 (3.96) Mounting Holes

Ø.312 (7.92) Clearance Top and Bottom

(50.8 )

5 V version

12-48 V version

Notes

1. All dimensions in inches (mm).

Tolerance .xx = ±0.02 (0.50); .xxx = ±0.01 (0.25)

2. Weight 0.22 lbs (100 g)

04 Dec 17

ECS60

Models and Ratings

AC-DC

J1 mates with Molex Housing PN 09-50-1031

Faston ground tab requires insolated receptacle

J2 mates with Molex Housing PN 09-50-1041

and both with Molex Series 5194 Crimp Terminals

Faston ground tab requires insolated receptacle

In put Connector J1

Molex PN 09-65-2038

Pin 1 Line

Pin 2 Neutral

0.25” Faston Earth

Out put Connector J2

Molex PN 09-65-2048

Pin 1 +V1

Pin 2 +V1

Pin 3 RTN

Pin 4 RTN

1.05 (26.7)

0.14 (3.5)

Components may

extend beyond

edge of PCB

by 0.04 (1.0)

1.62

(41.1)

1.30

(33.0)

0.20 (5.1)

C5 C18

0.28 (7.1)

4 x ø0.156 (3.96) mounting holes

ø3.12 (7.92) clearance top and bottom

3.00 (76.2)

1.75

(44.4)

0.12

(3.18)

2.00

(50.8)

2.75 (69.8)

0.12

(3.1)

Mounting points A should be connected together for optimum EMI performance

0.25 faston ground tab

Mechanical Details

1. For covered versions, add suffix ‘-C’ to model number or order part number ECS25-60 COVER KIT for standalone cover. Not suitable for use in class II installations,

derate output power by 20% with cover.

Notes

Output Power Output Voltage Output Current Model Number(1)

40 W 5.0 VDC 8.00 A ECS60US05

60 W 12.0 VDC 5.00 A ECS60US12

60 W 15.0 VDC 4.00 A ECS60US15

60 W 24.0 VDC 2.50 A ECS60US24

60 W 48.0 VDC 1.25 A ECS60US48

Thermal Considerations (All ECS25-60 Models)

In order to ensure safe operation of the PSU in the most adverse conditions

permitted in the end-use equipment, the temperature of the components listed

in the table must not be exceeded. See mechanical drawings for component

locations. Temperature should be monitored using K type thermocouples

placed on the hottest part of the component (out of

any direct air flow).

Temperature Measurements (Ambient ≤50 °C)

Component Max Temperature ºC

T1 110 °C

Q1 110 °C

C5 100 °C

C18 100 °C

Notes

1. All dimensions in inches (mm).

Tolerance .xx = ±0.02 (0.50); .xxx = ±0.01 (0.25)

2. Weight: 0.22 lbs (100 g)